Search Documents

By Alastair Torrance

The performance of commercial explosives is clearly influenced by the conditions under which they are used. Mining companies are supplied with Technical Data Sheets which provide details about explosive properties and its suitable application. These are generally produced using laboratory techniques which may not accurately reflect the quality and performance of the product in the field.

Jan 1, 2013

By Aris Tambunan, Nella Lubis, Nurafrianti Saala, Komang Widhiayanto, Herry Saputra, Rudolf Sitorus

Maximizing mining recovery rates and minimizing ore loss are pivotal objectives for economic efficiency and operational effectiveness. This study explores methods to address these imperatives by enhancing ore production and recovery through improved blasting techniques and spillage control in the Martabe Gold Mine Project in North Sumatra Province, Indonesia. Between 2018 and 2021, the average mining recovery rate stood at 93%, resulting in a potential annual ore loss of 7% and a potential quarterly financial impact of close to $2 million. Maintaining and enhancing mining recovery became crucial, with a planned 30% increase in total material movement for 2022. The mining recovery target for 2022 was set at 96% based on best achievement historical data from 2021 to increase ore tonnage by 203 KTon per annum. To achieve the primary objective of increasing ore production by improving mining recovery, the study focused on predicting and controlling the movement of blasted ore to reduce spillage and enhancing the grade control model to reflect actual conditions post-blasting. Several alternative solutions were explored, primarily emphasizing drilling and blasting activities. Essential methods included capturing the actual blasting movement to adjust the ore block based on blasting design data and post-blasting muckpile topography. This approach minimizes ore loss by providing output as ore block adjustment based on post-blast movement data. In addition, the tie-up design was adjusted to control ore spillage outside the pit ridge. The implementation of these methods yielded significant improvements. Adjusting the ore block based on actual blasting movement contributed $1,545,764 in benefits. Controlling ore spillage outside the pit ridge achieved a 10% reduction in spillage, contributing $79,184 in benefits. These enhancements successfully met the 2022 mining recovery target of 96%, marking a 3% increase from 2021. Consequently, ore loss was reduced by 178 KTon throughout 2022, resulting in a financial impact of $7.3 million. The study underscores the significance of precise blasting techniques and effective spillage control in enhancing mining recovery rates.

Jan 21, 2025

By William Reisz

Many different types of drills coming in a wide range of sizes and configurations are used in the blasting industry today. While each system may have its own unique attributes and capabilities, it may hold its own perils as well. This article will focus primarily on hazards that are mutual to most every type of drilling system.

Jan 1, 2013

By Samir Garcia, Alain Mestanza

This technical work was carried out in an open pit copper mining unit, located in central Peru, which has a daily production of 440 thousand tons per day. Currently the pit consists of three mining phases, however, in phase 05 north, there is the construction of a shaft with a height of 375 meters, the function of this structure is to collect and drain the water coming from the pit, there is the importance of preserving its stability and keeping it operational, guaranteeing the sustainability of the operation. For this, a controlled blasting plan was developed that goes from level 4530 to level 4455 to place the central well on a bench, reactivating the pools.

Jan 21, 2025

By Malcolm Scoble, Yves Lizotte, Ajit Singh

Fragmentation size assessment faces difficult problems, traditionally involving tedious and time consuming procedures. Early work had been directed towards developing empirical methods of predicting rather than measuring fragmentation. More recent development of computer-based image processing techniques which derive size distributions by analysis of photographic or video images are reviewed. These are now being adapted by various workers to fragmentation analysis in mines. Results are presented from experimental work aimed to establish the accuracy and precision of photographic techniques for muckpile assessment. Reference is made to McGill fragmentation studies at surface and underground mines in Canada, relating to experience gained in photographic and image processing techniques. The various factors that affect such techniques as well as their limitations and strengths are discussed.

Jan 1, 1990

In situ, most Taconite is heavily pre-fractured; because of the high cost of comminution of taconite, maximum fracture of pre-existing blocks is desirable. Sustained borehole pressure plays a significant role in fragmentation, especially by penetrating pre-existing fractures. The distribution of explosive-induced energy in the burden in three dimensions was calculated. Data on the comminution of single particles was used, with the distribution of energies and the distribution of pre-existing block sizes, to calculate fragmentation for a case study. The calculation agreed well with the measured fragmentation. Sequential comminution events are much more efficient than single ones, and enhanced fragmentation may be possible with alternative blasting practices. Some important factors in the dependence of comminution on energy input are discussed.

Jan 1, 1995

By S C. Alford

Explosive fracturing of metal is usually considered to be an imprecise process but, by careful consideration of shock-wave geometry, precise results are obtainable. The limited development of such charges is attributed to experimental difficulties. A charge configuration has now been devised in which a prismatic wave-shaping element is used to resolve the shock-waves entering a target plate into two convergent components. The extreme pressure caused by their collision initiates a diamond fracture in the proximal target face, and coincidence of reflected tension waves generates a fracture in the distal face. A combination of these effects breaks the target. An embodiment of S.R.T. is described which is flexible, magnetic and contains no cavities.

Jan 1, 1986

By Yonghun Jong, Chungin Lee

The main purpose of this study was to apply the artificial neural network (ANN) models to determine optimal powder factors and predict peak particle velocities, based on a series of observations and input parameters. The used blasthole pattern was V-cut. The locations of blastholes and ignition patterns remained almost constant. The input parameters were 14 geological conditions (i.e., dip, dip direction, spacing, separation, and persistence of 2 discontinuity sets, tunnel orientation, rock strength, RQD, and RMR) and 4 blasting conditions (i.e., distance between blasting points and measuring points, charge weight per delay, drilling length, and blasting efficiency). Data for the ANN application in this study were recently collected in a highway tunnel under construction in Korea. The main rock type in the site was biotitic granite. An optimum ANN model was determined by training models with collected data. The trained model was used to evaluate the prediction capability of the optimum model. It was shown that the ANN model could predict the powder factor and the peak particle velocity depended upon the selected input parameters. Particularly, the ANN model predicted more accurate peak particle velocities than those obtained by the blasting vibration equation. Moreover, the more dominant factors among the input parameters could be determined by analysis of the relative strength effect.

Jan 1, 2002

By Randall M. Wheeler

Many blasting companies are using simulated production ground vibration waveforms to aid them in the control of their vibration effects. The simulations are typically produced by using a seismograph to record a signature waveform from a single hole shot and subsequently applying the various delays to be used in a proposed production design. The ability of this simulation method to give good results usually depends on three primary factors. These are: 1) the homogeneity of the seismic travel path from hole to hole; 2) the consistency of the seismic energy release per unit of explosive from hole to hole; and 3) whether or not the delays fire as planned.

Jan 1, 1991

By Francis O. Otuonye

A time series and system analysis modeling technique was applied to signals from strain egages mounted on a fully grouted resin roof bolt and signals from accelerometers mounted on the bolt head and roof rock to determine the roof bolt's response to repeated blast loading. The derived model gives a comprehensive quantitative description of the modes of vibration of the roof bolt response to each blast loading. The damping ratios and natural frequencies of the modes of vibration can reveal the alteration of the process dynamics due to the deterioration of the roof rock and can be used to identify the incipience of instability in the roof bolt system.

Jan 1, 1987

By Kenneth K. Eltschlager, Richard R. Brochu

At the International Society of Explosives Engineers Annual Conference held in Nashville, Tennessee in February 1995, a Seismograph Standards Committee was established. The purpose of this committee was to develop objective performance specifications for vibration measurement instrumentation and field use practices. It was also understood that due to geology, temperature, and moisture in the soils, it is not possible to design and build an instrument to give results which are absolutely comparable for ground vibration. It was, however, considered essential to standardize instrumentation by which vibration can be measured under closely defined conditions so that results obtained by users of seismographs are always the same within stated tolerances.

Jan 1, 1999

By C. Yi, D. Johansson, C. San Miguel, M. Wimmer

Sublevel caving (SLC) is a mass mining method based upon the utilization of gravity flow of blasted ore and caved waste rock. Production blasting has significant impact on the efficiency and productivity of SLC output, affecting material fragmentation, flow and recovery. Misfires could occur during blasting in SLC, which results in the loss of explosives and poor fragmentation. Usually, the blastholes are top-initiated with redundant lower primers set at + 25 ms as a precaution. If the top primers fail, the lower primers may initiate the explosive, which will induce out-of-sequence delays that can influence fragmentation and gravity flow. This work investigated the impact of misfires and out-ofsequence delays on fragmentation and gravity flow through numerical simulations using a coupled finite element and discrete element method. Different scenarios of misfires and out-of-sequence delays were studied, and the fragment size distribution was obtained to evaluate the blasting performance. The material flow behaviour was investigated to assess the gravity flow process. The results indicated that misfires significantly affect the fragmentation and the gravity flow process while the effects of out-of-sequence delays are not so significant for the investigated cases

Jan 1, 2024

By Catherine T. Aimone-Martin, Susan G. Beattie

A series of small scale explosive tests were performed at a perlite mine near Socorro, New Mexico. The tests were designed to investigate the azimuthal or directional relationship between small scale geologic structures such as joints and the propagation of explosively-induced ground motions. Three shots were initiated within a single borehole located at ground zero at depths varying from 83 m (272 ft) to 10 m (32 ft). An array of three component velocity and acceleration transducers were placed in two concentric rings at distances of 20 m (66 ft) and 40 m (131 ft) surrounding the single hole at 7.5° , 15° , and 30° azimuths as measured from ground zero. Data from the transducers were then used to determine the average propagation velocity and waveform characteristics of the blast vibration through the rock mass at the various azimuths. The rock mass was mapped to determine the predominate joint orientations (strike and dip) and the average propagation velocities were correlated with this geologic information. The results showed that there is a correlation between the predominate joint orientation and ground motion amplitudes and velocity. The more predominate geologic structures allow the wave to follow along their strike thereby forming a planar path of least resistance and in turn, allowing higher velocities and amplitudes. Secondary joints or structures may act in concert with more prominent features to form a network of channels or paths along which the wave moves more freely than it may when traveling against the structures. The greatest azimuthal variations in velocity and amplitude was observed for the shallow shot at 10 m (32 ft) depth.

Jan 1, 1996

By Earl C. Hutchison, John Loviza

At the Metropolitan Nashville International Airport, with its more than 600 scheduled daily flights from American Airlines hub operations, other scheduled airline flights, Tennessee Air National Guard operations, as well as numerous industry air flights, the excavation of 300,000 cubic yards of rock was required without disrupting airport operations for a cut and cover underground tunnel with a 4 lane US Highway and new airplane runway to extend across it's top. In addition to the excavation, the removed rock was to be broken to specification type that was clean and of small size for fill in another area of the airport property. The blasting was limited to two 1/2 hour windows per day and stiff monetary penalties were in place for schedule slippage of each phase of the project.

Jan 1, 1992

By Qi Jingyue, Wang Zhongquian, Yang Nianhua

Qinling Tunnel is the longest tunnel in China. The rock stratum is very hard rock - intact mixed gneiss. At the beginning of the construction, drift-pilot excavation is very costly due to the use of regular drill and blasting methods. After tests on the acoustic impedance match between rock and explosive, watergel explosive, which has a high velocity of detonation and high brisance, has been used for hard rock blasting. In addition, different cut plans have been compared. It was found that four-large-hole cut is the most effective. And the number of drillholes and specific charge cut down and the average advance reaches more than 94% of the blastholes depth. Thus, the difficult problem of hard rock blasting in drift pilot is successfully solved, while safe and quick construction is guaranteed.

Jan 1, 1998

By Sanjay Sengar, Nabiullah Pingua, Saurabh Sahay

In India, more than 80 percent of the total of 557 million metric ton coal production comes from open-cast mines involving large overburden removal with average 1:3.5 stripping ratio which is going to in-crease in future. This operation consumes nearly 0.5 million metric ton explosives consisting of 80-85 percent bulk explosives and remaining 15 to 20 percent non-permitted large diameter explosives. Quali-ties of bulk explosives play an important role in rock blasting. Post blast results like poor fragmentation, tight mucking, toe problems, improper muck profile and lower productivity of mine may require chang-es in explosive loading factor (amount of explosive used per unit of rock blasted ). The explosive load-ing factor is an extremely important index to assess the economy of blasting operation.

Jan 1, 2014

By Edward J. Walter

Our modern technology is provided with a unique but flexible power tool in the use of explosives. A by-product of explosives usage is vibration or elastic deformation of the earth which is annoying to the ordinary person and can be damaging to structures. The problem is not new, it is more than fifty years old. Adequate vibration standards have been developed so that blasting programs can be properly planned and safely executed. Changes in our social culture have somewhat changed the emphasis in blasting vibration from damage considerations to the much lower level of citizen annoyance. Vibration codes based on this level will be highly restrictive and prohibitively costly. Cooperation is urged between operators, community officials, agencies at all levels,and consultants to see to the development of sound realistic vibration codes.

Jan 1, 1975

By Jim Daley

SEE is a dynamic organization composed of people from all facets of the explosives industry who are truly interested in the advancement of that industry. I had been a miner at the Homestake Gold Mine in Lead, SD for 12 years when I decided to obtain a mining engineering degree. The mental and economic consequences of that decision were more severe than we had imagined. The joint scholarship program of the Northern Plains and Black Hills Chapters of SEE provides assistance to several college students each year. I was fortunate enough to receive scholarships from this program twice and this assistance helped me and my family with both monetary and psychological support during times of need so that we could stay focused on the goal of obtaining a degree.

Jan 1, 1995

By Ian Tolliday

Emulsion Explosives manufacturers are aware of the destabilizing effect that the presence of inorganic impurities such as magnesium and iron and organic impurities such as naphthalene sulfonates and alkyl amines can have on their emulsions. This destabilization often manifests itself as severe crystallization and subsequent product loss. This paper describes the performance testing of specifically developed emulsifiers which give greatly improved emulsion stability in the presence of high levels of impurities. The test work involved a series of stability tests using ammonium nitrate doped with various levels of crystal modifier and anti-caking agent. A further series of tests were done to evaluate the stability using ammonium nitrate doped with various levels of iron and magnesium ions.

Jan 1, 2018

By R Vuolio, B A. Jonsson

In the center of Helsinki - capital of Finland - extensive blasting operations were carried out during the years 1982 - 84. At the corner of the streets Mannerheimintie and Simonkatu - in the Forum block - about 125,000 cu.m. of rock were blasted to give place for a new modern shopping centre (Fig. 1). Added to this amount of rock another 10,000 cu.m. were blasted for a transport tunnel to an adjacent underground bombshelter (Fig.2) which is to be used as a parking place in peace-time. The blasting work was demanding and difficult to carry out due to old buildings surrounding the work-site as well as computers and other sensitive equipment installed in some of them.

Jan 1, 1985