Search Documents

There are interactions between different minerals from the same ore, minerals and grinding media, and the electrochemical conditions present in the system. Grinding in steel rod and ball mills is a common practice in minerals processing. It is accepted, that the electrochemical interactions between the grinding media and minerals in a grinding mill, influence the corrosive wear of balls/rods and the surface properties of the ground minerals. A complex massive sulphide, Cu-Zn, TAKNAR, Iran, was used for all the experiments. The aim of this study was to investigate the effect of grinding media (dry or wet) on the pulp chemistry and recovery of Cu and Zn in bulk concentrate. 1100 g of ore samples were milled, and mill products with d80=85 and 75 micron in wet and dry grinding methods were produced. Rougher bulk flotation experiments were performed with 550g ore samples, at 30% solids. SIPX in conjunction with Aero238 in 1:2 ratio (48 g/t), was used as mixed collector system, and copper sulphate (200g/t) and MIBC (20 g/t) were employed as sphalerite activator and frother. Lime and High purity Oxygen gas were used for adjusting pH at 8.5 and aeration. The results showed that, more positive pulp potentials were measured when the feed had been ground in a dry environment, and the difference in pulp potentials between the dry and wet ground feed was approximately 250 mV after the grinding stage. In dry grinding method, the recovery of Cu and Zn increased approximately 5 and 10%, respectively. In addition, in dry ground samples, the volume of middling and coarse particles (+100 micron) were more and Dry ground flotation feed had better agreed with using a mixture of collectors. After using copper sulphate, pulp potential increased about 50 mV in dry and 75 mV in wet grinding methods. Keywords: grinding media, pulp potential, Cu-Zn massive sulphide, bulk flotation

Sep 1, 2012

By A. Saramak

"The paper focuses on problems of atmospheric pollution by the dusts, produced during the course of crushing and grinding processes, and the main objective of investigative programme is an assessment of emission of particulate pollutants for following crushing devices operated in plant scale: impactors, cone and jaw crushers. All crushers operate in aggregate production plants in Poland. In the first stage of investigations there were determined dust emission levels and supporting characteristics for all crushers under investigation. Then there were introduced indices that allow for comparative analysis in terms of dust emission, for devices with different energy consumptions and comminution ratio. It appeared that crushers with high the overall dust emission do not always achieved unfavorable dust emission per comminution ratio or energy consumption. The introduced indices proved their usefulness, because they helped to carry out a comparative analysis among crushers, operating under different technological conditions. It is also easier to assess environmental impact of individual crushing devices, under analysis. Results of investigations also show that environmental impact of different types of crushers is diverse and it is difficult to compare dust emissions of various types of crushers without taking into account technological aspects (like throughput, comminution ratio, energy consumption, and others) of their operations.INTRODUCTION Mineral processing of raw material is a complex process, involving in general operations of size reductions and separation. Depending on the type of specific raw material, the technological circuit may include operations of comminution and size classification. This is a typical circuit for aggregate production. In ore treatment industry the process in much more complicated and include also a metallurgical treatment of ore concentrate – the final product from processing plant stage.In general, regardless the type of raw material, operations of size reduction are present in each technological circuit of mineral processing. Operations of crushing and grinding are an integral part of processing technology, because they play a crucial role in effective treatment of mineral raw materials (Gawenda 2013). Their duty is to liberate the useful minerals from the gangue in ore treatment industry, or to produce the material with the required particle size in case of aggregate processing. Crushing and grinding operations are of a high negative impact on environment and humans. They consume great amounts of energy, what indirectly contributes to higher emission of carbon dioxide CO2. Apart from energy, crushing and grinding device consume significant amount of steel and other metals and alloys due to high wear of working parts and grinding media. This is also of negative environmental impact due to emissions of additional amounts of CO2 in production of steel and other metals required as spare parts for comminution devices."

Jan 1, 2018

By Reza M. Rahman, Seher Ata, Graeme J. Jameson

"This paper presents the results of a through investigation into the froth recovery measurements in a controlled plant environment using a device that allows direct collection of dropback particles from the froth phase. Test work was performed at the Northparkes concentrator (NSW, Australia), using a feed taken from the head of the cleaner scavenger bank. The feed slurry had a relatively higher copper grade varying from 5.2% to 6.8%. Experiments were performed to investigate the effect of important flotation parameters such as air flowrate on the froth recovery. The size of the particles in the relevant streams was also analysed to acquire in-depth knowledge about the froth dropback mechanism. The results suggested that the froth recovery could be as low as 70%, although it was relatively easy to achieve the values in the range 75% to 85% by the correct choice of operating variables. It was found that the air flowrate has a positive impact on both collection (pulp) and froth zone recoveries. However, the effect was more prominent in the froth zone. It appeared that the froth recovery is a strong function of particle size."

Jan 1, 2014

By Jiajun Geand, Shuli Wang, Baodong Pan, Xueqi Cui, Guangwei Zhang, Jipeng Sun

Gravity-fed three-product dense medium cyclone(GTDMC)is usually used as the main coal washing equipment in coking coal preparation plant. It can produce three products with a low density suspension at the same time. Raw coal and dense medium are fed separately into the cyclone. Only the qualified low-density medium suspension is pumped into the cyclone while the raw coal is fed into the first-stage 1200mm cyclone axially at the top end by gravity. The 1200mm cyclone with a cylindrical form is for low-density separation. The clean coal with light density and slower-settling velocity moves directly towards the low pressure zone along the axis and is carried through the vortex-finder to the overflow. Only the heavy products pass through the "separating zones" to the wall of 1200mm cyclone and then migrate into the series-connected second-stage 850mm cyclone through the tangential outlet. The medium suspension from the first-stage cyclone is thickened and contains more magnetite coarse particles. The second-stage cyclone typically consists of a cylindrical section and conical part. These are all favorable for the second-stage cyclone to separate at a high density. Production practices show that the clean coal and the gangue rarely mixed in the middling, the lower limit of the separation is 0.2 mm, the Organic Efficiency and the Ecart probable of the first stage is 98.30% and 0.026 kg/L respectively.

Jan 1, 2014

By A. Gueciouer, A. Akkouche, K. Chalah, A. Benmounah

"Drilling solid waste is a typical industrial solid waste, and it is a major pollutant source to ecological environment. Generally, waste management dewatering systems separate solids and fine particles from the liquid phase of drilling fluid, thereby leaving a clarified aqueous solution and allow the cleaning of waste fluids. Typically, dewatering waste management systems clean drilling fluid through coagulation, flocculation and/or mechanical separation. Chemicals used in dewatering are based on the coagulation-flocculation process, which it facilitate the removal of suspended solids and colloidal particles. The factors which can promote the coagulation-flocculation are velocity gradient, contact time, and PH. The objective of this work is to optimize a formulation adequate for dewatering based on the coagulation-flocculation process used coagulant (Aluminum sulphate), anionic flocculants (Partially Hydrolyzed Polyacrylamide) and anionic polyelectrolytes (in solid form with linear chain with very high molecular weight). The results obtained show the good efficiency of the coagulant and flocculants. INTRODUCTION Rig site dewatering of drilling fluids with recycling of processed water can help an operator to comply with environmental rules by reducing volumes of waste and reducing long term liabilities. It can also reduce disposal costs and provide a cleaner drill site overall. Most of the environmental concerns during the 1980s involved hazardous materials and toxic wastes. Drilling fluids, many of which are chemically benign, have escaped many of the difficult-to-comply-with rules and regulations. During the 1990s, however, operators may be required to submit a written plan for liquid waste reduction for even nonhazardous materials. Many states and local agencies may institute total bans on oil field wastes. Drilling rigs typically produce about 1 bbl of liquid waste for every 1 ft of hole drilled. Thus, a typical drilling operation can produce a large quantity of waste [1]. To improve the dewaterability of sludge, different pretreatment processes have been widely studied and developed including thermal, chemical, magnetic, mechanical, acoustic, electric, electro-acoustic and their hybrid treatment processes [2]. Rig site dewatering (figure 1) is the process of injecting coagulants or flocculating chemicals into the mud entering a large clarifying centrifuge. Coagulation occurs when the solid and allowing it to be attracted to other solids by van der waals forces. Flocculation is the binding of individual solid particles into aggregates of multiple particles. It is physical, rather than electrical, and occurs when one segment of a flocculating polymer chain absorbs simultaneously onto more than one particle [3]."

Jan 1, 2018

By C. Y. Sun

Flotation of chalcopyrite and unactivated malachite with xanthates (ethylxanthate, butylxanthate, octylxanthate and dodecylxanthate) is studied in this paper. Minerals interacted with xanthates are detected by FTIR, and simulated by molecular mechanics. It shows that chalcopyrite can be floated with 4 kinds of xanthates, and unactivated malachite can?t be floated with ethylxanthate but can be floated directly with later 3 kinds of xanthates while characteristic absorption peaks of those four kinds of xanthates are all detected by FTIR on chalcopyrite and malachite surface. After simulating the interaction between xanthate and mineral, it shows that H2O and OH-can interact with chalcopyrite and malachite, and their interaction energy may be so called energy bulwark which must be overcome by collector when collector interacts on minerals; the two sulfur atoms in xanthate group interact with copper and neighbor iron atoms on chalcopyrite. It also shows that molecular mechanics results with logP of collectors can interpret the mechanism of xanthate-mineral on atom scale.

Jan 1, 2014

By L. Filippov

"Nickel is an important metal with the total global consumption of about 2 million tons per year. It is sourced from both sulfide and laterite ore, but currently laterites are becoming more attractive for nickel production due to the depletion of high grade nickel sulfide ores. Laterites are generally processed by hydro or pyro-metallurgy and therefore, pre-concentration of nickel before such processes is very important. In this paper the effect different physical methods (including flotation) on the pre-concentration of nickel in laterite ores will be discussed. The ore used in this study was a laterite from South East Asia. Nickel was upgraded using different methods such as magnetic separation, flotation and sizing. The effect of ore mineralogy on choosing the best strategy to upgrade nickel will be discussed. The findings of this project will help to unlock a substantial volume of nickel with significant value from laterite ores.INTRODUCTION Nickel is an important metal with the total global consumption of about million tons per year which has grown rapidly during last decades (Mackey, 2011). Nickel is sourced from two different types of ores, sulfide and laterite. The majority (about 70%) of the world’s nickel resources occur as laterite ores which are often complex, and low grade, and therefore expensive to treat using conventional methods (Xu et al., 2013). Today, nickel laterites are more attractive for production of nickel as the amount of high grade nickel sulfide ores has diminished (Janwong, 2012). Therefore more economic processes to recover nickel from these resources should be developed.It should be noted that nickel laterite mineralogy is complex, and nickel often presents as ultrafine inclusions in a number of mineral phases. Because of the low nickel concentration and variable distribution in these phases, effective upgrading by physical separation processes would be challenging. Researchers have tried to improve nickel laterite flotation recovery by using a number of feed preparation techniques. A summary of the nickel grades obtained using flotation and magnetic separation as reported in the literature is presented in Table 1. It can be seen that only minor nickel upgrades have been reported. Quast et al. (2015) have concluded that the complex mineralogy of nickel laterite ores makes it difficult to achieve any significant nickel upgrading by physical techniques, including flotation. They achieved 40% increase in the nickel content (from 1.0% to 1.4%) at a nickel recovery of 43% (Quast et al., 2015). Various attempts in USA, New Caledonia, India and Australia, to upgrade nickel in laterite using magnetic separation have not been successful (Quast et al., 2015). A recent comprehensive review on topics influencing nickel laterite flotation has shown that further investigations in the flotation of laterite ores are undoubtedly warranted (Farrokhpay & Filippov, 2016)."

Jan 1, 2018

By Elzbieta Mielczarski, Jerzy Mielczarski, Jan Drzymala, Yann Duvalm

Polyethylene glycol monoalkyl ethers (CnEm) render quartz hydrophobic while feldspar remains hydrophilic. As a result quartz can be separated from feldspar in small frothless flotation devices such as the Hallimond tube. The separation can be accomplished at room temperature at pH < 7 and C16E33 concentrations between 10-5 and 10-4 M for quartz particles smaller than 0.4 mm. No separation is observed when feldspar ore containing about 60 % of feldspar and 40% of quartz is subjected to flotation in a laboratory flotation machine. The reason for the lack of separation is a low hydrophobicity of quartz in the presence of polyethylene glycol monoalkyl ethers and high intensity of mixing in the flotation machine. The flotometric tests showed that the contact angle of quartz in monoalkyl ethers of polyethylene glycol solutions is less than about 18 degrees and depends on the structure and concentration of the ether and the pH of the system.

Jan 1, 2003

By Rong Fan, Andrea Gerson

"The small recovery of Ag, often in the order of 50%, by traditional flotation and leaching process strategies is closely related to the complicated and heterogeneous nature of Ag-bearing minerals with Ag typically being associated with numerous minerals within any given ore-body. Moreover, grain sizes may be extremely fine with micron-scale common. In order to design cost-effective Ag-bearing mineral flotation and leach recovery strategies it is firstly necessary to characterise the speciation of Ag and its correlation with other elements, e.g., Cu, As and Sb, within the ore matrix and process streams. The traditional QEM-SCAN analytical approach can prove problematic for some mineralogies due to difficulties in recognising degrees of crystallinity, polymorphs, complex solid solution series, high value trace element mineralogy, very fine grained materials; and the requirement for a comprehensive data base. Moreover, there is difficulty ‘seeing’ either surface films or surface contaminants which can both lead to poor flotation performance. There is therefore clearly a need to develop confirmatory and complementary approaches when these uncertainties arise. Synchrotron X-ray microprobe analysis provides a powerful tool for the mineralogical characterisation of finely segregated heterogeneous Ag-containing materials. These measurements enable comprehensive characterisation of the Ag-bearing components using synchrotron microprobe X-ray fluorescence mapping (µ-XFM), X-ray diffraction (µ-XRD) and X-ray absorption spectroscopy (µ-XAS). Further analytical strength is provided by principal component analysis of laboratory ToF-SIMS data which enables the statistical identification of correlated surface species enabling examination of surface chemical characteristics responsible for mis-reporting of Ag containing components within flotation streams. We describe the application of these techniques to a selected Ag-containing feed and tail and demonstrate how these compliment and extend traditional analytical methodologies."

Jan 1, 2014

By Leopoldo Gutierrez, Esau Arinaitwe, Marek Pawlik

"The effect of various polymers, including: anionic carboxymethyl cellulose (CMC), polystyrene sulfonate (PSS), humic acids (HA) and non-ionic hydroxypropyl cellulose, on the wettability of Athabasca bitumen was evaluated through dynamic contact angle measurements using the captive bubble technique. The tests were carried out as a function of pH at a constant ionic strength (0.01 mol/L sodium chloride). The evolution of the three-phase contact angle between the solution, bitumen and an air bubble was followed as a function of time over a period of ~6 minutes. The contact angle data were modelled using a first-order kinetic equation. The results were analyzed in terms of the initial contact angle, the evolution rate constant, and the steady-state contact angle value. In the case of anionic polymers, a pronounced decrease in the initial contact angle value was observed at pH 3. Under acidic conditions, there was no significant effect of CMC observed on the steady-state contact angle value but PSS and HA significantly decreased the steady-state contact angle value. At pH 8.5. the anionic polymers did not affect the wettability of the bitumen surface but they significantly decreased the contact angle evolution rate. These results suggested that CMC is not capable of permanently lowering the hydrophobicity of bitumen, and the polymer only slowed down the evolution of the contact angle to the steady-state value. The results also showed that polystyrene sulfonate and humic acids were capable of making bitumen hydrophilic but only under acidic conditions. Only hydroxypropyl cellulose (HPC) produced a large decrease in the steady-state contact angle under alkaline conditions (pH 8.5). The kinetics of contact angle evolution in the presence of HPC was also drastically lowered. The results were discussed in terms of the chemical composition of the polymers and their different affinities towards the bitumen surface."

Jan 1, 2014

By Masakazu Niinae, Tasuma Suzuki, Mai Moribe, Yohhei Okabe

Bench-scale electrokinetic experiments were performed to elucidate the electrokinetic remediation mechanisms of arsenate from artificially contaminated kaolinite. The electrokinetic experiments in which a constant voltage was applied demonstrated that high soil pH favored arsenate remediation with respect to both the remediation time and electricity consumption. It was also demonstrated that applying a pulse voltage (1 hour ON, 1 hour OFF) significantly improved the electricity consumption efficiency when the soil pH was maintained at the initial value during the experiments; this trend was not observed when the soil pH was gradually increased from the cathode side. These electrokinetic experimental results indicate that the remediation rate-limiting step varied with soil pH. When the soil pH was maintained at the initial value of 7.2 during the experiments, arsenate desorption was the remediation rate-limiting step rather than the migration of dissolved arsenate toward the anode. Conversely, when the cathode pH was not controlled and the soil pH was correspondingly increased gradually from the cathode side, the migration of hydroxyl and desorbed arsenate ions toward the anode played a more important role in the control of the overall remediation efficiency.

Jan 1, 2014

By C. L. Lin

Previous research on particle damage during high pressure grinding roll (HPGR) crushing was limited by the resolution of point-projection micro CT systems and the extent of damage was described by the percent of particles cracked for different crushing methods as determined at a voxel resolution of 40 microns. With recent advances in X-ray optics, the resolution afforded with point-projection micro CT systems has been improved by at least an order of magnitude using a lens-based X-ray micro CT system. With the use of X-ray lens imaging the resolution is determined by the lens rather than by the spot size of the micro-focus X-ray source. The high resolution X-ray micro CT (HRXMT) system made by Xradia with a voxel resolution of less than 1 micron is now being used for the characterization of particle damage during HPGR crushing. In this way, the direct 3-D determination of the internal damage of crushed ore particles which vary from 40 mm down to 100 microns in size is being studied at a voxel resolution of a few microns. The number, size, and shape of cracks can now be measured at this improved resolution and for the first time the specific crack surface area distributions of the crushed product can be calculated from HRXMT images using specially designed software tools for 3D analysis. Results from selected crushing operations are presented. Copper ore particles from HPGR crushing at high pressure (6 N/mm2) are severely damaged having crack specific surface areas as great as 10 mm2/mm3. Keywords: HPGR, particle damage, X-ray micro tomography, crack surface area

Sep 1, 2012

By Adam Jordens, Olga Kuzmina, Christopher Marion, Kristian Waters

"In order to meet the growing demand for non-Chinese rare earth suppliers many new rare earth (RE) mineral deposits are currently under development, however these deposits typically include many minerals for which there is little processing information available. One of these deposits is the Nechalacho deposit located in the North West Territories of Canada. This deposit contains multiple RE minerals including bastnäsite, zircon, fergusonite, allanite and monazite. The work presented here investigates the use of different classes of flotation collectors (carboxylic acids, hydroxamic acids, phosphoric acids) typically used in RE mineral flotation to float the Nechalacho ore directly. Flotation tests are also conducted as the final step in a beneficiation process incorporating centrifugal gravity concentration and magnetic separation. This combination of centrifugal gravity concentration and magnetic separation rejects low specific gravity gangue minerals such as K-feldspar and plagioclase and concentrates high specific gravity minerals such as magnetite and hematite. The removal of low specific gravity gangue helps to improve flotation and the removal of ferromagnetic iron oxides is important prior to flotation using certain chelating collectors."

Jan 1, 2014

By Stephen Simukanga, Jewette Masinja

"Mining has been going on commercially in Zambia for over 100 years. The backbone of the mining industry has been copper production and its by-products of cobalt and gold. Over these years, the mining industry ownership structure has swung from private ownership to state ownership in 1972, and back to private ownership in 1995. Environmental management was first introduced into the body of Zambian legislation in 1991 through the promulgation of the Environmental Protection and Pollution Control Act (EPPCA). The Act’s main functions included the protection of the environment and control of pollution, and in particular to provide for the health and welfare of the people, animals, plants and the environment in general. This Act, was replaced in 2011 by the Environmental Management Act (EMA). The new Act has a number of new elements including: mainstreaming environment in national planning, it provides for the domestication of multilateral environmental agreements, enhances public participation issue, creates a central environmental information depositary, elaborates access to information principles, establishes an environment fund, creates enforcement orders, provides for both Zambia Environmental Management Authority and members of the public to sue for damages following environmental pollution, and provides for the appointment of honorary Inspectors. In addition to this, the Mines and Minerals Act of 1995 provided, for the first time, a section on environmental management in the mining sector. This section also created the Environmental Protection Fund (for mining), and made it obligatory to undertake environmental impact assessment before mining permits could be issued. The Environmental Protection Fund has now been established, as provided for by the law, and currently has more than USD9.0 million in the account. Secondly, environmental auditing is now being carried out annually on mines around the country, the effect of this has been a significant improvement in the environmental management of mining in Zambia. This paper looks at the response of the Zambian mining sector to these pieces of environmental management legislation, and the direction that the mining sector is expected to take on environmental management going forward."

Jan 1, 2014

By H. Palza, C. Ihle, S. Contreras

"Processing of minerals, particularly treatment of tailings, has been increasingly challenged by the presence of clays in the feed of thickeners. This occurrence is expected to become increasingly important given the nature of ore deposits currently being exploited and those that have been recently discovered. In sedimentation operations (solid-liquid separation), industrial flocculants often fail to coagulate clay-containing fines, generating supernatants with high levels of turbidity, thus implying operational problems. Recently, it has been reported that graphene oxide (GO), a graphite derivative with high oxygen-containing groups, could enhance the flocculation of clay systems, due to the interaction between clays and GO functional groups. In the present work, we investigated the effect of doping industrial flocculants (commercial polyacrylamide) with GO on the floculation of kaolinite suspensions in a solid-liquid separation stage. Separation performance was evaluated by studying flocculation kinetics using a focused beam reflectance measurement (FBRM) instrument, in a set of batch tests. A statistical analysis of the flocculation kinetics and floc population distribution was further carried out. Our results suggest the existence of a synergistic effect between the studied flocculants and GO. This effect is observed as a decrease of clay fine contents in the supernatant, thus improving solid-liquid separation eficiency for high clay containing tailings. INTRODUCTION Copper, given its mechanical, physical and chemical characteristics, is a critical material for the progress of society and so has been from early stages of mankind. Demand for this metal has increased due to the growth of cities and the technological explosion, leading to increase current mining production and reinforce the efforts in exploration for new deposits (Elshkaki et al. 2016). As copper-rich deposits are being depleted, it has been necessary to develop proper technology to mine deposits of lower grades and more complex mineralogies, keeping in mind that the economic window that allows the exploitation of them is reduced by the increase on operating costs (Crowson 2012 and Northey et al. 2014). High clay bearing minerals are found in many of those low-grade copper deposits, and they induce problems in all stages of the mineral processing route (Taner and Onen 2016). Particularly, in the solid-liquid separation stage, the flocculation process fails to remove the clay fraction from suspension and it leads to operational issues such as filter damage, overconsumption of reagents and the need to add an extra clarifying step for the recovered process water. Those problematics pose an interesting challenge."

Jan 1, 2018

By Wei Zhang, Jinhong Zhang

"In froth flotation, the adsorption of collector on mineral surface is critical for a successful flotation process. In present work, an atomic force microscopy (AFM) has been applied to study the adsorption of potassium amyl xanthate (PAX) on copper sulfides, i.e., chalcopyrite, chalcocite and bornite. The in-situ collected AFM images show that PAX adsorbs on chalcopyrite mainly in the form of oily dixanthogen; while it strongly adsorbs on chalcocite and bornite in the form of insoluble metal xanthate, which binds strongly with the mineral surface. The information obtained from the AFM study shed lights on the collectivity and therefore the selection of specific collector for different copper sulfide minerals in industrial practice.INTRODUCTIONFroth flotation, which treats the highest throughput in mining industry and produces the maximum economic outcome of any surface chemistry process, has been widely applied for the concentration of copper sulfide minerals, i.e., chalcopyrite, chalcocite and bornite. In flotation, collectors are added into the pulp (mixture of water and fine-grained minerals) to selectively adsorb onto the target mineral and render its surface with high hydrophobicity, which is generally beneficial for a strong mineral-bubble attachment and thus a high flotation recovery. Therefore, the adsorption of collector on mineral surface is vital for a successful flotation process and it has been studied by applying various surface analysis techniques, such as IR (Infrared Spectroscopy), CV (Cyclic Voltammetry) and XPS (X-ray Photoelectron Spectroscopy). (Poling, 1963; Allison et al., 1972; Mielczarski et al., 1984; Leppinen et al., 1989; Kartio et al., 1996) These studies have revealed a lot of information, such as the reaction, product and mechanism, of the adsorption of chemicals on mineral surface. It is also of great interest to directly get the image of adsorbed collectors on mineral surface changing with pulp chemistry, such as pH, redox potential, ionic strength and chemical’s dosage."

Jan 1, 2018

By Tsvetan Damyanov, Nikolay Hristov, Evgeni Kostadinov, Lubomir Kuzev

"The process of grinding in drum mills is directly dependent on the dynamic forces occuring in the free movement of the grinding bodies in the volume. The subject of discussion are the potential impacts between grinding bodies having different shape and equal weight in a drum mill that has a diameter of 1200 mm. The study utilised ball grinding bodies having a diameter of 120 mm and tetraballpebs having a conditional diameter of 120 mm. The study was carried out using the Solid Works Simulation software. The following cases were examined: • Impact between two identical grinding bodies; • Impact between a grinding body and the shell surface. The study provided numerical values for impact force, kinetic energy of impact, linear speed of impact, linear displacment of the center of gravity and duration of impact deformation. The impact force of the balls is approximately 179000 N. The impact force of the tetraballpebs with typical vertices, edges and spherical surfaces depending on the area of impact is 177000 to 185000 N. Upon impact between two spherical surfaces of tetraballpebs, the contact area is 263.55 mm2, which is more than twice the contact area upon impact between two balls, which is 114.39 mm2. This determines better conditions for the transmission of kinetic energy by reducing opportunities for overgrinding."

Jan 1, 2014

By K. C. Corin

It is well known that the grinding circuit plays a crucial role in flotation. The effect of pulp chemistry during grinding is often overlooked. It is believed that the surface properties of the minerals can be adjusted during flotation rather than during grinding. However, recent development in surface analysis techniques (TOF-SIMS, XPS, and AES etc.) have proven that the hydrophilic iron hydroxides formed at the mineral surface during grinding make it difficult for collector adsorption, which may result in poor grades and recoveries of the valuable minerals. This study investigated the effect of the pulp chemistry conditions during milling and the subsequent effects on flotation performance of an Nkomati ore. The results have shown that there was approximately 10 % increase in Ni recovery, when the ore was ground at a dissolved oxygen (DO) concentration of 0 ppm (DO-0) in comparison to no gas control during the grinding stage. However, when the pH was changed from 9 to 11, no gas control resulted in a 20 % decrease in the Ni recovery compared to only 5 % decrease in the Ni recovery at DO-0. A noteworthy observation is that controlling a combination of DO and pH during grinding is of critical importance for better floatability and selectivity for such a system. It also became clear from this study that the presence of oxygen is critical to the consumption of xanthate, which is consistent with the general literature. It has been established that grinding at lower DO levels/redox potentials (Eh) in the presence of xanthate significantly improves the flotation performance of the valuable minerals.

Sep 1, 2012

By P. Basarova

The attachment of bubbles onto a collecting surface is an ubiquitous natural phenomenon, playing a critical role in numerous practical processes. The goal of the project is to broaden the knowledge about hydrodynamic interactions between small bubbles and large solids that occur in nature and industrial processes. Focusing on collision processes between a single rising bubble (Db<1 mm) and a larger falling spherical particle in stagnant liquid, the theoretical model describing the bubble trajectory is given here. The model is based on analysis of forces acting on the bubble, and utilizes equation for the bubble motion. Mobile and immobile type of bubble surface mobility are considered. The calculated results are compared with the experimental data; here a high-speed video camera was used to capture the bubble motion and bubble-particle interaction. Very good agreement between experimental and calculated data was found. For both types of surface mobilities, the bubble deviation in the horizontal direction is nearly linear. The proportion constant is bigger for immobile bubble surface and increases with the bubble size. Furthermore, particular forces acting on bubble were studied. A similar course of relative bubble velocity and force impact was observed for identical bubble position. For cases when the bubble centre is close to the particle axis, only deflection in one direction is observed. When the bubble is reaching the maximum trajectory, the force ratio is changed. The bubble is firstly pushed away from the particle, but when it is within close distance from the particle, the bubble is pushed towards the particle.

Sep 1, 2012

By John Ralston

"Interfacial chemistry plays a pivotal role in bubble-particle capture, for it controls whether or not attachment occurs. Surface heterogeneity, degree of surface hydrophobicity, bubble nucleation and related phenomena influence the stability of the aqueous wetting film between a particle and an approaching bubble. The latter must be unstable if capture is to occur. Various techniques that may be used to quantify this interfacial, chemistry-dominated behaviour, are described.The efficient capture of specific particles by rising bubbles and the delicate control of interfacial chemistry that leads to selective capture are central issues in froth flotation. For efficient capture to occur between a particle and a bubble, they must undergo a close encounter, a collision process dominated by hydrodynamics. Should this encounter bring the particle and bubble within the range of attractive forces, the intervening liquid film between the bubble and the particle will drain, leading to a critical thickness at which rupture occurs. The liquid-vapour interface then retreats over the solid particle surface until a stable wetting perimeter is established. The particle and bubble are then joined after this attachment process. The particle may only be dislodged from this state if it is supplied with sufficient kinetic energy to exceed the detachment energy in this detachment process. These various events are now well documented and may be followed using high-speed videomicroscopy (Schulze, 1984; Nguyen et al., 2001).The process of collision can now be described quantitatively for single bubbles colliding with bubbles under various flow regimes (Dai et al., 1998) and appropriate scale up is possible for multiple bubble particle collisions occurring under turbulent conditions (Pyke et al., 2002). In this paper we will be concerned with the role of interfacial chemistry and how this influences the attachment process."

Jan 1, 2003