Search Documents

By Peter J. Coghill, Michael J. Millen, Brian D. Sowerby, Kirby D. Cunningham

"CSIRO Minerals has developed an integrated particle size analysis system for deployment in the grinding circuits of minerals processing plants. The system includes a slurry sampling station, a de-aeration tank and an ultrasonic particle size analyser (UltraPS). The UltraPS analyser is based on ultrasonic attenuation and velocity spectrometry combined with gamma-ray transmission. The technology is applicable to the measurement of 0.1 to 1000 µm diameter particles directly in highly concentrated slurries without dilution. The analyser incorporates a gamma-ray transmission gauge utilising an ultra-low activity radioisotope source that is exempt from International Atomic Energy Agency (IAEA) and Australian licensing regulations.The UltraPS analyser consists of a submersible probe and an electronics package. The probe can be immersed directly in a minerals processing plant stream if the aeration level in the stream is low. For applications where a de-aerated slurry stream is not available, CSIRO has developed an integrated system that includes a sampling station, a de-aeration tank as well as the UltraPS analyser itself. A schematic drawing of the continuous flow gravity fed system is shown in the figure. A commercial sampling system is used to supply slurry at a rate of 2.5m3/hr to the deaeration tank. The aim of the de-aeration tank is to remove air in the slurry to a level where meaningful particle size measurements can be performed. The tank volume is about 0.2m3, thus giving the slurry flowing through the tank a mean residence time in the tank of approximately five minutes. Tests at a number of concentrators have shown that five minutes is sufficient time for slurry to de-aerate to a level where ultrasonic measurements can be made. The tank incorporates an ultrasonic level detection sensor and flow to the deaeration tank is adjusted based on the level of slurry within the tank. The UltraPS probe is mounted through a flanged section of duct, which is bolted to the bottom of the de-aeration tank."

Jan 1, 2003

By W. Pawlos

"The paper will present the methods of visual observation and recording of movement paths of coal grains of different physical properties in the paramagnetic liquid. The paths were recorded with a video camera in the working chamber by means of a specially constructed device, acting as a periscope, which were then transformed into digital images.Experimental movement paths were confronted to the paths obtained in a theoretical way by means of solving differential equations of movement. The outlet level of a grain of the same physical properties from the separator is a random variable with normal distribution which modal value is equal to the outlet level of a spherical grain, calculated from the solution of grain movement equations. At these assumptions it is possible to calculate the height of the passage from the separator working chamber to separate a given product with a given separation accuracy, measured by a probable error and to determine separation conditions."

Jan 1, 2003

By S. Fiore, M. C. Zanetti, C. Clerici

The processes and fluxes of a cast iron foundry plant located in the North of Italy were analyzed in order to determine the amount and kind of wastes produced from the different activities. The main fractions are the molding sands, furnace muds and powders coming from the dust abatement plant, the exhaust lime, the furnace refractory, the metallic shotting and the sludges and powders coming from the dust abatement plant of molding lines for a total production equal to 800 t/d. All wastes were sampled and particle-size and chemically characterized to evaluate the best recycling or reuse solutions. Wastes were sieved and divided in three categories according to the particle-size dimensions: below 0.1 mm, between 0.1 and 0.6 mm and above 0.6 mm. The fraction above 0.6 mm dimension underwent magnetic separation to recover and quantify the potentially available iron fraction. The fraction between 0.1 mm and 0.6 mm was chemically characterized in order to understand if it could be fed to the sand regeneration plant. The below 0.1 mm fraction was characterized to evaluate the following recycling and reuse solutions: additive for molding sands and/or raw material for the concrete industry.

Jan 1, 2003

By S. Q. Zhu

Coal Water Mixtures (CWMs) are densed suspensions of coal particles in water. Viscosity is one of the most important rheological properties of CWMs and it is desired to be as low as possible. The slurry viscosity was influenced significantly by additive formation, the particle size distribution and the ash content of the coal. However, the influence of dispersants is most obvious. At present, there are several kinds of dispersants such as polymeric styrene sulfuric sodium, lignin sulfonate, humate, polycarboxy salt, ethylene epoxide surfactant. In this paper, a newly synthesized CWM dispersant has been reported, which is an efficient anionic surfactants of polycarboxylic acid type. The synthesis process includes three steps. At the beginning, the polyglycol acetate ester has been performed by acetic acid and polyethylene glycol (PEO) on the condition of acetic-acid/PEO ratio 1:1.1, at 368~373K for 30 minutes. Then the macro-monomer is prepared through the esterification of 85.71% acrylic and 14.29% polyglycol acetate ester, at 368~373K for 10 minutes. After that, the polycarboxylic acid CWM dispersant is polymerized using proper proportion macro-monomer, acrylic (AA) and sulfonic styrol sodium, at 368~373K for 1 hour. This new dispersants are used in the coal water mixtures formulation. Four kinds of coal used in the experiment are Shuang Yashan, Tunliu, Luning, Changcun samples. ? The highest concentration for shuanyashan coal is 70% when the dosage of dispersant is 0.4%, and the content of -200 meshes particles is 75.53%. As the dosage of dispersant de-creases to 0.25%, the Shangyashan CWM concentration is 67%. ? For Tunliu coal CWM concentrations are in the range of 76% to 75% when dosage of the dispersant changes from 0.4% to 0.25% at the same particle size distribution of 83.5% minus 200 meshes. ? The highest concentration for Luning coal is 69% when dosage of the dispersant is 0.4%, and the content of -200 meshes particles is 88.86%. ? For Changcun sample, the coal concentration of CWM is 73%~75% when dosage range of the dispersant is 0.35%~0.5%. The experiments show that the synthesied dispersant is quite promising for some coals CWM preparation, but a little bit coal-dependent. The Proximate and Ultimate analysis, surface characteristic measurement have been made to investigate the interactions between coal and additives.

Jan 1, 2014

By A. Collings, A. Farmer

Power ultrasound may be used in the processing of mineral suspensions to clean the particle surfaces of oxidation products and fine coatings, mainly through the large, but very localised forces, produced by cavitation. This effect may be utilised in lowering the level of iron contamination in silica sand used for glass making, in improving the sharpness of electrostatic separation of heavy mineral concentrates, in shortening the time of leaching of minerals and in improving the selectivity and recovery of flotation processes. Parameters affecting the efficiency of these processes, such as input power and levels of reagent addition, are discussed. In particular, we present data showing the relationship between power input and the particle size of surface coatings removed, which can be explained by the Derjaguin approximation for the energy of interaction between a sphere and a flat surface. Pilot scale studies, using commercially available components, are currently being used to assess process viability and will be compared with laboratory scale results.

Jan 1, 2003

By S. Mitra1

"This study aims to investigate coarse particle detachment mechanisms (particle diameter > 150 ?m) utilising both experimental and numerical technique. Two mechanisms were studied – (i) interactions of bubbleparticle (BP) aggregate with vortices and (ii) coalescence of bubble-particle aggregates. On the first mechanism, interaction behaviour of coherent vortex structures with a BP aggregate (bubble diameter db = 3 mm, particle diameter dp = 0.3 mm) was studied using a CFD model in the Reynolds number range of 100 to 1000. Effect of surface hydrophobicity on the BP stability was examined using a range of contact angle boundary conditions. To address the second mechanism, interactions of bubble-particle aggregate (db ~ 4 mm, dp ~ 0.4 mm) with both free gas-liquid interface and individual bubbles were investigated using high speed imaging. Both rebound and coalescence outcomes were observed to be responsible for BP instability leading to particle detachment.INTRODUCTIONIt is widely known that flotation process performs excellent mineral recovery for base metal ore particles that are typically in the range of ~ 20 to 150 µm in diameter (Jameson, 2010). More specifically, higher recoveries are usually reported for particles in the size range of ~20 to 70 µm while outside this spectrum, generally the recovery diminishes significantly. It would be highly desirable to improve the recovery of particles at the coarse end of the flotation size range spectrum which has significant economic benefit (Jameson, 2010). However, it is essential that insights to particle detachment phenomenon, the primary impediment in coarse particle flotation caused by the underlying hydrodynamic factors are first obtained at a greater depth.In an ideal quiescent liquid medium, due to inertia, coarse particles deviate substantially from the fluid streamlines and collision efficiency with bubbles decreases which can only be augmented by increasing turbulence level in the medium sufficiently to make random physical contacts with bubbles. Nonetheless, even if successful contacts are made, it is difficult for these large particles to remain attached to bubbles in a turbulent shear flow environment. There are two major mechanisms postulated for particle detachment – interaction of turbulent flow structures (eddies) with BP aggregate and coalescence among surrounding aggregates. Earlier work of Schulze (1982) theorised a vortex acceleration component to characterise turbulence effect on BP aggregate instability in flotation machines. Wang et al. (2015) investigated bubble detachment behaviour from a stationary particle in a nearly homogeneous and isotropic flow field. Using PIV (particle image velocimetry), it was shown that the local maximum energy dissipation rate for the case of bubble detachment was significantly higher than the no detachment case, and was also higher than the critical value for bubble detachment calculated using Schulze’ theory (Schulze, 1982). Later, Wang et al. (2017) also visualised the BP aggregate instability in a cavity flow leading to particle detachment which was attributed to bubble coalescence, bubble surface oscillation and particle deceleration phenomena."

Jan 1, 2018

By L. A. Cisternas, R. I. Jeldres, C. Cruz, P. A. Robles

"Previous studies have shown that the floatability of chalcopyrite in seawater at highly alkaline conditions is significantly affected by the presence of clays. The reason is that the species of calcium and magnesium present in seawater under those conditions may act as a bridge between the surfaces of clay and chalcopyrite, generating massive aggregates that then depress. In this context, the objective of this work is to analyze the impact of pretreated seawater with low amount of calcium and magnesium ions on the recovery of a sulphide copper mineral with high kaolinite content as clay. The seawater pre-treatment is done by the addition of sodium hydroxide in a high carbon dioxide environment. The chemical reactions realized under these conditions lead to the formation and precipitation of calcium and magnesium species that are subsequently removed by vacuum filtration. The pre-treated seawater is then used in flotation tests at pH 11 for copper sulphide, where the mineral is synthetically prepared by mixtures of chalcopyrite, kaolinite, and quartz. When comparing the flotation results for different types of water, including seawater and pre-treated seawater, a significant effect is observed: as the seawater hardness decreases, which comprises the calcium and magnesium ions, the recovery of chalcopyrite is increased. However, the effect is markedly enhanced in the presence of kaolinite. Therefore, the results indicate that sodium hydroxide and carbon dioxide are able to remove different species of calcium and magnesium from seawater and could improve the chalcopyrite recovery with high kaolinite content. INTRODUCTIONIn many cases, mineral deposits are found in arid areas with little access to water resources. Water is a fundamental element to carry out the unit operations that achieved the separation of valuable minerals (especially in concentration operations). Seawater has acquired an interesting role in recent years (Cisternas and Moreno, 2014); in fact, it seems to be one of the few viable options to ensure the sustainability of the mining industry in arid zones. At present, there are numerous experiences of industries that use or have used this resource, either by submitting the seawater to a desalination treatment by reverse osmosis or by applying it directly, without desalting. The latter case may involve significant economic benefits (for example, by avoiding the investment of building a desalination plant) and in some cases some operational benefits. A positive aspect is that in general terms the foaming in the saline medium is much more efficient compared to fresh water (Quinn et al., 2014; Castro et al., 2010). Some reports show that the foaming doses required to achieve a certain quality of bubbles are remarkably reduced, reaching exceptional cases such as Xstrata's Raglan concentrator, where it did not even include foaming to carry out the operation. This fact is quite promising, considering that some researchers have stated that controlling the quality of bubbles and foam could float minerals through coarse particles. This would lead to multiple benefits, such as energy savings by avoiding excessive grinding and a lower presence of fine ore that causes major problems in water recovery operations by gravitation (such as thickening) and in tailings management. However, seawater also causes significant challenges in multiple operations (Jeldres et al., 2017, 2016; Castro et al., 2010), as for example in minerals with high clay content (Uribe et al., 2017). In fresh water, the presence of clays minerals in ores is already a major problem in the flotation stages since the operation becomes difficult to be controlled, and operators are commonly forced to increase the consumption of reagents because the collectors are deposited on the clays' surfaces reducing froth stability (Farrokhpay and Bradshaw, 2012). Sometimes the use of rheology-modifying reagents should also be incorporated since the pulps become more visc"

Jan 1, 2018

By P. Somasundaran, G. Anastassakis, Z. Pan, D. R. Nagaraj

Gums are often used as depressants for talceous gangue minerals in the flotation of nickel and platinum bearing ores. However, the mechanisms of gum adsorption on talc are not clearly established. In this work, adsorption of guar gum at the talc-solution interface is investigated using spectroscopic and allied techniques. Guar gum adsorption on talc is not affected significantly by changes in solution conditions such as pH and ionic strength. Electrokinetic studies showed that guar gum decreased the negative zeta potential of talc but did not reverse the charge. Fluorescence spectroscopy studies conducted to investigate the role of hydrophobic bonding using pyrene and dansyl probes showed no evidence of the formation of hydrophobic domains at talc-aqueous interface. Urea, a hydrogen bond breaker, reduced the adsorption of guar on talc to the same extent as that for guar/alumina system, in which hydrogen bond plays an important role. All of the above results suggest that one of the main driving forces for guar adsorption on talc is hydrogen bonding rather than electrostatic or hydrophobic force.

Jan 1, 2003

By Sergio Castro, Janusz Laskowski

In the flotation in highly concentrated electrolyte solutions not only ionic strength but also chemical composition, flotation pH and mineral properties play an important role. As a result an improvement or depression may be observed. A strong improvement in the floatability of hydrophobic bituminous coals and other inherently hydrophobic minerals is characteristic for the "salt flotation process", which is carried out in concentrated electrolyte solutions at natural pH and without addition of any flotation reagents. However, pH is a key factor when saline and hipersaline waters with hydrolyzing metallic ions are used as process water. In the case of flotation of Cu-Mo sulfide ores in seawater, molybdenite is strongly depressed by the Mg2+ hydrolysis products when pH is raised to depress pyrite. Process water with a high content of Mg2+ and Ca2+ ions, and this also includes seawater, have deleterious effect on the anionic flotation of industrial minerals with fatty acids. The flotation of potash ores is carried out in NaCl-KCl saturated brine (6-7 mole/L of NaCl and KCl) with the use of long-chain amines. Such a high electrolyte concentration changes dramatically the amine Krafft point making the collector insoluble in brine; its mode of action entirely differs from that in conventional flotation processes.

Jan 1, 2014

By N. Acarkan

Beneficiation of the pyrite concentrate of the Kastomonu-Küre (Northern Turkey) copper ore seems to be attractive due to its high Cu, Co, and Zn contents. Pyrite concentrate were used in the experimental studies. Cu, Co, and Zn were recovered from the concentrate by the sulphatizing roasting, leaching and the precipitation using H2S. Sulphatizing roasting experiments were carried out in a rotary furnace and the optimal roasting conditions were found to be at 650°C roasting temperature and 3.0 h roasting period and addition of Na2SO4 of 3 % for the concentrate containing 0.58% Cu, 0.22% Co, and 0.04% Zn. Then, the roasted product was repeatedly leached with 10 g/L H2SO4 solution. Optimal conditions were found to be 60 oC leaching temperature, 2 h leaching period, and 30% pulp density. Leaching efficiencies for Cu and Co were over 99 %. The valuable metals in the pregnant solution were selectively precipitated by H2S as sulfides. Selective precipitation of Cu, Zn, Co was achieved by adjusting the pH and the temperature of the leach solution. Final metal recoveries of 99.20% Cu, 99.40% Co, and 95.60% Zn were attained. The precipitated sulphides are marketable products. Roasting gases with their 15% SO2 content are suitable for the production of H2SO4 and the leach residues can be integrated with the iron ore processing plant as they contain 57.50 % Fe, 17.70% gangue (SiO2, CaO, etc.), 0.04% S, and 0.06% non-ferrous metals.

Jan 1, 2014

By Emile Scheepers, Chris Aldrich, Jacques J. Eksteen

The pneumatic injection of CaC2 powder into molten iron has become a very reliable and effective way to carry out desulphurisation. The key variables that influence the kinetics of this process are the condition and composition of the top slag, the oxygen activity in the hot metal and the injection conditions. Notable injection parameters include carrier gas flowrate, reagent flowrate, lance depth and initial sulphur concentration. A one-dimensional, steady-state model for momentum, heat- and mass transfer in rising gasliquid- powder plumes was developed for conditions relevant to the CaC2 refining process at Saldanha Steel?, South Africa. Combined with a model that predicts the contribution of the topslag to the process, the overall rate of desulphurisation as a function of time was determined, thereby quantitatively demonstrating the influence of the above-mentioned injection parameters on the kinetics of the desulphurisation process.

Jan 1, 2003

By F. Bello, R. Yanez, M. Pinto, T. Errazuriz

"Throughout its operation, Minera Esperanza (ME) will deposit one of the largest tonnages rates of high density tailings in the world with a solids concentration of close to 67% by weight. The tailings presently being deposited have a solids concentration of approximately 62% - 64%, and so cannot be used to directly characterize the flow and deposition characteristics of the higher concentration tailings. To increase the knowledge of the behaviour of their tailings, ME, with the support of Golder Associates, developed a large scale tailings deposition test with a capacity of 30,000 tonnes per day (1,200 m3/h). The test was carried out by depositing tailings into two large cells or paddocks in five stages. Multiple spigots were used to allow different flows to be deposited. At each stage, topographical surveys of the natural terrain and the geometry of the deposited tailings, as well as continuous flow measurement and periodical rheological characterization of the discharged tailings were conducted to create a data set against which beach slope models could be calibrated and then used to predict performance of the higher concentration tailings under different deposition scenarios. This study adopted the beach slope prediction model proposed by A.L. Li (Li, 2011). The model was successfully adjusted to the observations made during this large scale field test by applying the values measured in-situ. This paper presents the application of the model, the results obtained, the findings, and the analysis of possible future scenarios. The model was applied, using the discharge flow rate, the geometrical characteristics of the discharge area, and the rheology with its variation along the beach to estimate the development of the beach formation and the steady state of the beach slopes. Through the use of dimensionless variables, the model was applied to higher solids concentration scenarios, obtaining results that would allow beach slope estimation at different deposition stages in multiple scenarios of varying parameters such as flow, rheology and geometry of discharge area."

Jan 1, 2014

By Kevin Davey, Liza Forbes, Leanne Smith

Given the global scarcity and value of potable water, interest in the use of water of lower quality in mineral processing has grown significantly in recent years. Previous laboratory batch flotation tests conducted at CSIRO have shown that chalcopyrite floats strongly without collector in distilled water and that the collectorless flotability of chalcopyrite is unaffected by the use of brackish water, sea water or hypersaline water. In contrast, bornite is moderately flotable without collector in distilled water but all three lower-quality waters have a detrimental effect on the recovery of bornite. The depressant effect is so strong that the little recovery achieved in these waters was only slightly above what might have been expected from entrainment alone. This work has now been extended to another important copper sulfide mineral, chalcocite. In contrast to chalcopyrite and bornite, chalcocite does not exhibit collectorless flotability so the chalcocite tests in this study were performed in the presence of a standard collector (potassium ethyl xanthate). The results reveal that chalcocite is flotable with xanthate in distilled water but the lower-quality waters have a detrimental effect on the recovery of chalcocite. This effect is partly reversed by increase collector additions. Further tests were completed in order to investigate the effect of the different ions present in the saline waters on chalcocite flotation. Possible reasons for the observed differences are discussed in terms of the pulp chemistry of the system.

Jan 1, 2014

By K. V. Fedotov, G. I. Sarapulova

The study is devoted to the earth's surface protection and is aimed at improving the ecological safety of the territories in the mining industry. Identification of the diagnostic signs and quantitative criteria for the disturbance of soil geochemical properties and water chemistry represent an important scientific task in anthropogenically disturbed landscapes in the context of comprehensive exploitation of mineral resources. The study is aimed at geological and ecological analysis of the migration peculiarities of the man-caused chemicals and elements in soils and soil-surface water environment. We received new results. These results assist in estimating the peculiar features of distribution of heavy metals total and mobile forms (Cu, Ni, Zn, Pb), depending on the physical and chemical parameters of the disturbed soils. We obtained the empirical relationships describing heavy metals localization and accumulation processes depending on buffer properties of soils (pH, N, Corg), salinization factor and contamination with oil products. Anthropogenic geochemical barriers spontaneously formed in the area of industrial facilities were revealed in the territories of industrial facilities. These barriers prevent the further distribution of elements and pollutants in the landscapes. This makes it possible to create their artificial analogues in order to limit further migration of pollutants and to immobilize valuable components. Analysis of diagnostic features of soils geoecological state and factors influencing the distribution of heavy metals in the soil-surface water geosystem allows the identification of the geochemical barrier type with the aim of elements immobilization in a limited area of the territory. We applied modern physical and chemical methods of analysis, a package of statistics programs in Excel and modeling techniques. The proposed approach is innovative and therefore can be attractive. The accumulation of useful components losses in mineral resources exploitation is a promising reserve for their recovery from the soil with specifically arranged properties. The methodology of this research is also promising for the prediction of the environmental emergencies of the anthropogenic nature. This is consistent with the requirements of state control of environmental safety in the course of comprehensive exploitation of mineral resources.

Jan 1, 2018

By Junji Shibata

In a present process to treat the tungsten carbide tool waste, the wastes are roasted in air and then an alkali leaching is carried out in an autoclave. An environmentally friendly process is required to recover rare metals (Co and W) from the wastes. The effect of mechano-chemical (MC) treatment on leaching of rare metals was investigated in this study. The solvent extraction and crystallization-stripping methods were applied to separate and recover tungsten and cobalt in the leached solutions. The MC treatment for the rare metal leaching is effective to dissolve rare metals from the wastes due to the change in crystalline structure of WC and oxidation of WC with KMnO4. Cobalt ions are extracted with D2EHPA by a cation exchange reaction. Tungsten in the leachate can be extracted by TOA (tri-octyl amine) as an extractant, because tungsten species exist as a form of anionic species in acidic solution. The rare metals in organic phase are recovered as insoluble salts such as oxalates and ammonium salts in the crystallization-stripping process. Keywords:unheated oxidation, solvent extraction, crystallization-stripping, recycling

Sep 1, 2012

By Vasile Murariu, William Pate, John Herbst, Dilek Alkac

"Multiphysics models are essentially first principles models capable of providing very accurate micro scale predictions. The computational requirements for Multiphysics Models are extensive, precluding their direct use for flowsheet simulations. Population balance models get their form from theory but the model parameters have to be provided from experiments. The prediction errors for the population balance models are typically significantly higher than those for the Multiphysics Models but the computational effort for Population Balance Models is typically much less than that for the Multiphysics models. The hybrid model described here takes advantage of the strengths of each of the two primary model types and minimizing the weaknesses of each. The Multiphysics Model is used to perform high accuracy "experiments" that are difficult or impossible to conduct in laboratories or plants. The results of these experiments are combined with standard laboratory or plant data to parameterize and further enhance the Population Balance portion of the hybrid model. The creation of a useful Hybrid Model is demonstrated for a MP1000 secondary crusher. The validation of the hybrid crusher model is also presented. Finally the use of the Hybrid Model is illustrated in a full comminution flowsheet simulator."

Jan 1, 2014

By Naoki Hiroyoshi, Hajime Miki, Tsuyoshi Hirajima, Masami Tsunekawa

Acidic solutions for chalcopyrite leaching contain cupric, ferrous and ferric ions, and the oxidizing power of the solutions is indicated by a redox potential, determined by the concentration ratio of ferric to ferrous ions. This paper reviews our previous studies on the redox potential dependence of chalcopyrite leaching in sulfuric acid solutions. Leaching and anodic-polarization experiments showed that coexistence of cupric and ferrous ions activate anodic dissolution of chalcopyrite, causing faster copper extraction at the potentials below a certain value (critical potential). The analysis of the AC impedance spectra for chalcopyrite electrode indicated that a high-resistance passive layer grows on the chalcopyrite surface without cupric and/or ferrous ions, and that coexistence of these ions causes a formation of another product layer and inhibits the passive layer growth at low potentials. These results are explained by a reaction model assuming the formation of intermediate Cu2S due to chalcopyrite reduction and the subsequent oxidation of the Cu2S. The critical potential corresponds to the redox potential of the Cu2S formation and the predicted values matched with the experimental results. Catalytic effect of silver ions on chalcopyrite leaching was also discussed based on experimental results and the above model.

Jan 1, 2003

By J. Lindström, J. Hamuyuni, M. Lundström, J. Aromaa

"The rising demand for metals today, coupled with the scarcity of primary sources for raw materials threatens both technological advancements and industrial manufacturing. In order to meet the demand, metals and other resources trapped in waste streams, have to be harnessed. This philosophy supports circular economy, where metals and other resources are kept in a closed loop. The pickling acid recovery system of most stainless steel production is one such example where the dissolved metals such as iron, nickel and chromium are currently not completely recovered due to the limitations of the current technologies. The aim of this study was to assess the available metals recovery methods from extremely concentrated acids. The main aim is to simultaneously recover metals and keep sulphuric acid reusable in acid circulation process. From the available literature, the most promising methods were chosen for laboratory experiments. Based on experimental work, the results and observations of electrodeposition, solvent extraction, and freeze crystallization are provided. KEYWORDS Pickling acid, metal recovery, solvent extraction, cathodic polarization, Freeze crystallization. INTRODUCTION Pickling in stainless steel production is an essential surface treatment process (Regel-Rosocka, M. (2010); Agrawal and Sahu, 2009). It is applied for removing surface films such as oxides and chromium-depleted layers to improve the corrosion resistance and surface finish of steel (Regel-Rosocka, 2010). Whilst the process greatly improves the surface finish of the stainless steel, it generates large amount of used acid, containing dissolved metals including chromium, iron, and nickel (Agrawal and Sahu, 2009). Recovery of acid is common practice for most steel producing industries (Nyman and Koivunen, 1986). In this work, acid regeneration process is investigated so as to simultaneously reusing sulfuric acid and recovering the dissolved metals. Recovery of valuable metals even in very small amounts would also bring additional revenue to the steel production industry. At a time when metal production has also been challenged by lack of natural resources for raw materials, secondary sources for metals such as the acid pickling process therefore, have greater potential as supplements. From earlier studies, electrodeposition (Giovanardi and Orlando, 2011; Kuznetsov et al., 200; Rögener et al., 2012; Surviliene et al., 2006), solvent extraction (Alguacil and López 1996; Haghshenas et al., 2009; Kesieme et al., 2013) and freeze crystallization (Beyer et al.,2003; Hasan et al.,2017; Van der Ham et al., 1999) are some of the most established potential methods. Earlier studies have also shown that simultaneous recovery of acid and metals would require combination of different methods. This is primarily due to the nature of very stable metal containing complex compounds formed during pickling. These complexes must be broken down to free the metals for further recovery processes."

Jan 1, 2018

By P. S. Mukherjee

Mineral ilmenite is a major resource for titanium, whose major application is for production of Titanium dioxide (TiO2) for pigment application. The production of pigment grade TiO2 from ilmenite was earlier carried out by acid leaching, which has now been banned due to environmental regulations. Further acid leaching leads to loss of iron metal values as sulphate or chloride which are also treated as effluent. In thermal plasma processing the metal values are recovered as high value pig iron and Titanium dioxide is recovered as Titania rich slag containing 80 to 85 percent TiO2. The Titania rich slag has now been considered as a better input material than synthetic rutile for production of pigment grade Titanium dioxide. On the other hand, high value pig iron goes for automobile industry for specific application. An Inflight-flight Thermal Plasma Processing plant, used for the production of Titania Rich slag and high value Pig iron from ilmenite, with 20kg capacity was designed and fabricated. The reactor has the provision to utilize the flue gas generated for preheating the input of raw materials. Various aspects of designing the furnace operation include viz. Feeding the raw material at a fixed rate, designing the crucible used for melting ilmenite, proper cooling arrangements, an innovative method for tapping the melt, recovery of heat from the gases, various safety arrangements which are some of the important milestone of the present work. The various operations have been carried out through a controller panel. Experiments were carried out to optimize various processing parameters using statistical modeling. Large scale experiments have been carried out at 10 to15 kg scale. The material balance has been calculate, and it has been observed, that about 95 percent recovery could be obtained for both Iron and Titanium oxide from ilmenite. The detailed characterization on Titania rich slag and iron has been carried out. It has also been shown that using the above slag, it is possible to prepare nanosized Titanium dioxide powder containing about 98 percent Titanium dioxide by optimizing leaching conditions. Keywords: titania rich slag, ilmenite, thermal plasma

Sep 1, 2012

By T. Wang

A new kind of mixed chelate collector was prepared in order to separate gangue (mainly quartz) and iron minerals efficiently during room temperature. The collector was was composed of two chelate collectors DES and DA. Floatation tests were carried out under 28?C with mixed magnetic concentrates of Donganshan sintering plant, and optimal test conditions were obtained, in which a direct floatation was undertaken and then a close circuit reverse floatation tests ( one roughing, one cleaning, and two scavenging), and a result of Fe grade of siderite concentrate 36.49%, Fe recovery of siderite concentrate 10.65%, Fe grade of final concentrate 66.27%, Fe recovery of final concentrate 78.25%, and Fe grade of tailing 16.22% was gained. Fourier Transform Infrared (FTIR) Spectra and Zeta potential of siderite and quartz adsorbed the DES and DA collectors before and after were measured in order to analyze the reaction between the collector and minerals. Furthermore, Molecule electronegativity of DES and DA was calculated by Electronegativity Proportionality Principle (EPP). Results showed that DES molecules have five active adsorbing sites and their molecule electronegativity was stronger while DA molecules have three active adsorbing sites, which all make the mixed collector has efficiently collecting performance. Zeta potential results of Quartz and siderite showed that at pH 11.5 both kinds of particles charged negative and at this pH value the mixed collector were mainly anionic collectors which indicate that electrostatic adsorption does not exist at this situation. FTIR results showed that characteristic peaks of the mixed collector changed before and after adsorption with the minerals, which means that there exists chemical adsorption or hydrogen bonding.

Jan 1, 2014