Search Documents

By Robert Snow, Shibo Zheng, Wenyi Song, Xiaoqing Ma, Patrick Zhang

Numerous phosphate mineral depressants have been reported in the literature for use during anionic flotation of dolomite from carbonate fluorapatite in slightly acid circuits. In one part of this research, laboratory flotation experiments were conducted to compare the effectiveness of phosphate depressants to process ground, deslimed high-MgO Florida phosphate pebbles. Ten potential phosphate depressants were evaluated during laboratory anionic flotation of dolomite from phosphate in a slightly acid circuit using a sulfonated oleic acid soap plus oil as the dolomite collector. Eight of the depressants have been used by various investigators with foreign and domestic carbonate-phosphate ores. Four of the depressants were found to be reasonably effective during the current flotation study, namely: sodium tripolyphosphate (STPP), sodium hexametaphosphate (SHMP), tetrasodium pyrophosphate (TSPP) and diphosphonic acid (DPA). Without depressants, the sulfonate collector required to produce cell underflow phosphate products containing <0.80% MgO and MgO/ P2O5 ratio <.033 was 1.13 kg/ton of flotation feed at a flotation pH range = 5.5-6.0. Using this collector level with 0.91 - 1.36 kg/ton of feed of STPP, SHMP or TSPP yielded phosphate products analyzing 0.73-0.92% MgO and MgO/ P2O5 ratios = .027-.034 at 90.0-96.8% P2O5 recovery. Similar grade phosphate products were obtained using DPA as the phosphate depressant at 84.1-87.5% P2O5 recovery. When no depressant was used, a similar grade phosphate product was obtained at only 65.9% P2O5 recovery. Another part of the research aimed at reducing MgO content in the final concentrate from Florida phosphate plants by conducting dolomite flotation on the final concentrate. Numerous phosphate depressants were tested for this purpose, including acidic, neutral and alkaline reagents. The most effective phosphate depressant was found to be phosphoric acid, giving both high grade and recovery.

Jan 1, 2014

By X. Q. Chen

According to the different characters of the middle-low grade bauxite, based on the normal flotation & reverse flotation technology, the author innovates the new technology which is named bi-flotation, it integrates the advantages of normal flotation & reverse flotation, while avoids their disadvantages. Take Henan middle-low grade bauxite as research object, according to the pilot experiment of bi-flotation technology, the concentrate A/S is 9.37 and the recovery of alumina is 80.18% by flotation separate the raw ore which A/S is only 4.19.

Jan 1, 2014

By Z. Q. Zhang

The iron ore from Yichang in China assaying 41.64% Fe and 1.02% P is a low grade and high phosphorus oolitic hematite ore. The separation of iron minerals from gangue minerals in the ore by conventional processing techniques is ineffective owing to their close similar properties. The modification of iron minerals by microwave-assisted reduction was investigated in order to improve separability of the ore. The effects of microwave-assisted reduction on the subsequent low intensity magnetic separation and floatation were examined. The results show that the main factors affecting the reduction and separation process are grinding size, reduction temperature and reductant. Fine grinding of the microwave-treated ore to smaller than 0.074mm was found to be imperative due to the tiny dissemination characteristics of iron oxide minerals. After magnetizing reduction by microwave heating at 500?, the magnetic concentrate containing 58.36% Fe and 0.67% P can be obtained with the Fe recovery of 91.28%. Magnetizing reduction drops the floatability of iron oxide minerals, thus reverse flotation is fit for upgrading the magnetic concentrate to contain 62.13% Fe and 0.21% P with Fe recovery of 81.59%. Compared with present microwave-assisted reduction technique of carbon reductant, using a waste iron powder as reductant is a novel and effective technique without the green house effect caused by the release of CO and CO2. Waste iron powder with a faster response to microwave heating then coke and charcoal can be recovered by magnetic separation in a low cost and plays the role of reductant and microwave heating accelerator.

Jan 1, 2014

The ball level and pulp load play a key role in the operation of industrial scale ball mills. These two operating variables have a significant influence on the performance of the ball mill and any attempts to optimize these devices require manipulating either one or both of these variables. There are several models that can be employed to perform simulations to optimize the performance of industrial ball mills. However, most of these models require ball load and pulp load measurements as inputs to calibrate the model. The changes suggested by the simulator also provide operating regimes that involve moving either the ball level or pulp load and sometimes both of these variables. A ball mill model coded in JKSimMet was used in conjunction with the Sensomag to optimize the secondary ball mill at Waterval concentrator in South Africa. The results show that the perfect mixing ball mill model can be used in conjunction with the Sensomag to optimize the performance of the secondary ball mill.

Sep 1, 2012

The ever increasing demand for energy and the progressive depletion of crude oil resources, have renewed interest in oil shale as an alternative fuel resource. Weathered oil shale samples were assembled from El-Nakheil phosphate mine in Quseir area, Eastern desert, Egypt. The oil shale samples were prepared and analyzed by XRD (X-ray diffraction), XRF (X-ray fluorescence spectrometry), and optical microscopic techniques. Rock-Eval pyrolysis and total organic carbon were used to study shale hydrocarbon potential. A leaching procedure using inorganic and organic acids was used to selectively dissolve the oil shale associated ash forming minerals. XRD results showed that calcite is the dominant carbonate mineral, whereas primary silicate minerals are quartz and montmorillonite. SEM (Scanning Electron Microscopy) observations indicated that the organic matter is dispersed throughout the rock matrix. The acid soluble fraction upon leaching was determined to be 37.59 and 42.74 wt% by using 5% HCl and 10% HCl, respectively. The TOC was increased from 20.78 to 29.88 and 34.09 wt% by using 5% HCl and 10% HCl, respectively. Keywords: el nakheil oil shale, characterization, xrd, xrf, sem, elemental analysis, proximate analysis, ultimate analysis, thin section, rock eval pyrolysis, acid leaching

Sep 1, 2012

By Y. Q. He

The dynamic behaviors of the air bubbles in the dense gas-solid fluidized bed have a significant effect on the performance of dry coal separation. The combined method of experimental measurement and numerical simulation were conducted to conduct the research of the mean diameters and rising velocities of the bubbles in the fluidized bed. The calculation models of mean diameter and rising velocity of the single bubble were proposed. The results indicate that the models of the mean diameter raised by Rowe (1976) and the rising velocity raised in this work could be used to predict the bubble dynamic parameters in gas-solid fluidized bed. With the Geldart B type of magnetite powder as the medium solids and while the gas velocity of 1.5Umf=U=2.2Umf, the mean bubble diameter along the bed height is 36mm<Db<45mm, and the mean rising velocity of the single bubble is distributed in 40~65cm/s. The results of experimental measurement, numerical simulation and model predication provide well agreements finally. Based on the uniform fluctuations of air bubbles diameters and their rising velocities, the separation experiments of 50~6mm dry coal using the mixture of 0.3~0.15mm magnetite powder and <1mm fine coal as medium solids were carried out. The results show that the probable error, E is 0.06, which indicates a good separation performance by using the gas-solid fluidized bed. Keywords: dense gas-solid fluidized bed, bubble dynamic behaviors, numerical simulation, separation performance

Sep 1, 2012

By Sergey Dyachenko

"Following the adopted strategy for making the production modern, efficient and environmental friendly the Company completed a stage of the integrated program aimed at reconfiguration of its processing capacity.Upgrade of the Talnakh Concentrator with commissioning of two start-up facilities (SF) allowed an increase of 30% in its ore processing capacity up to 10 mtpa. In addition to a new high-tech equipment installed, a new concentration process was adopted offering the main advantage of 25-30% reduction of sulfides in concentrate. New concentration technology enabled the total amount of produced nickel concentrates (from Norilsk and Talnakh Concentrators) to be processed at upgraded smelting facilities of Nadezhda Metallurgical Plant and allowed decommissioning of smelting capacities of Nickel Plant resulting in emissions reduction by 30%.Nornickel plans to boost the capacity of Talnakh Concentrator to 18 mtpa by 2022, after commissioning of the 3rd SF. This will provide a shorter route for ores transportation from Talnakh mines along with improvement of cost/performance ratio of ore processing through the usage of the modern equipment and optimized concentration flow scheme. Total capacity of Talnakh Concentrator will be sufficient to process ores from Talnakh deposits with planned upstream assets development taken into account. Volume of ore mined from Norilsk deposits to be processed at Norilsk Concentrator will be also increased.Upgrading the crushing section at Kola MMC Concentrator in 2015 provided finer particles of the crushed ore, resulting in 6.6% increase in specific capacity of ore mills as well as 1% higher recovery of non-ferrous metals due to improved liberation of ore minerals.In 2015-2017 the Company was actively engaged in optimization of existing process flow schemes and parameters of Kola MMC, new high-performance reagents were adopted for concentration process, namely, collectors, depressors, flocculants. These measures allowed the Concentrator to reduce its annual operating unit costs and ensure sustainable production of concentrate with the lower grade of the incoming feedstock.Launched in October 2017, Bystrinsky GOK’s Concentrator was 3D designed and received a range of advanced technological solutions.All design process procedures and technologies rolled-out at the Company’s concentrators were developed by Russian R&D institutes, with the key role of Gipronickel Institute, R&D Service of Kola MMC and Polar Division's in-house Engineering Support Centre."

Jan 1, 2018

By Qidong Zhang, Yongsheng Song, Wenjuan Li, Guiying Zhou, Kun Song

"Molybdenum is a very important rare mineral resources, which exists largely in oxidized ores and sulphide ores in nature. About 99% of metallic molybdenum comes from molybdenite. The talcose molybdenum resources are abundant but the resources utilization is low, because the talc is naturally hydrophobic and the floatability of talc is similar with molybdenite, which lead to difficult separation by flotation. Talc is easy entry into concentrate in flotation which can cause the content of MgO overhigh, therefore the molybdenum concentrate grade can not meet the industrial requirements. Thus the utilization level of talcose molybdenum resources has been restricted greatly.The adsorption of water on talc and molybdenite surfaces and natural floatability of minerals were studied by density functional theory method. The results showed that molybdenite and talc were layered minerals which exhibited similar surface wettability and H2O molecule prefers to stay with water rather than the minerals surfaces. N2 is adsorbed on talc and molybdenite surfaces more easily than H2O. The interaction and flotation behavior were studied by SEM and flotation experiments. The reason why talc interferes with the flotation molybdenite has been revealed. The agglomeration between molybenite and talc was caused easily in neutral or acidity solution, and it was dispersing between molybenite and talc particles in alkaline solution. The flotation results showed that good floatability of talc was the key factor causing a low grade of concentrate in alkaline solution. Thus, it is the key factor to enlarge floatability difference between molybdenite and talc.INTRODUCTIONMolybdenum is a kind of important rare metal and strategic reserve resources (Zhitao Y et al, 2016a). Due to excellent characteristic, such as high melting point, good thermal property and et al, it’s widely used in metallurgy, machinery, chemical, aerospace, and many other areas. It has become an indispensable metal in modern industry. Molybdenum generally exist in the form of molybdenite which is a kind of mineral with excellent natural floatability. Talc is a kind of typical hydrous and layered magnesium silicate minerals (Beattie D et al,2006a), which is one of the most common gangue mineral of the platinum group metal ores and metal sulfide ores (Tao L et al,2011). Due to its good native floatability, talc is easy entry into the concentrate product with foam in the process of sulfide ore flotation (Kelebek S and Smith S, 2006b), which resulted in decreasing concentrate indexes. Not on that, the high-content MgO of concentrate will also produce a series of adverse impact to the subsequent smelting (Lotter N O et al, 2008). Therefore, it is difficult to separate talc from sulfide ore concentrate effectively."

Jan 1, 2018

By Matheus Tocchini, Henrique Kahn, Juliana Antoniassi, Carina Ulsen, Eldon Masini

"Sand and gravel are the second and third largest minerals in production in Brazil, and this is increasing noticeably. The extraction of natural sand from river beds is increasingly restricted and most of the sand used in large cities comes in from more than 150 km away, resulting in high transportation costs. As a result, it has become more common to use crushed rock as artificial sand. The main difficulties in this process are controlling the shape of the particles and the content of deleterious materials, such as mica. Within this situation, this paper presents an alternative to using artificial sand for concrete use. Our procedure involves the following steps: a) sampling sand from different production days, b) characterizing the bulk sample by particle size and shape distribution, chemical composition by X ray fluorescence and mineralogical composition by X ray diffraction, c) removing fine grains by air classifier, d) performing intensive attrition with high pressure washing and e) characterizing products. The results demonstrated that this sample contains a huge proportion of fine grains and a notable content of mica, which is distributed along all sieve fractions. The presence of mica makes the use of sand in concrete unfeasible, moreover scanning electron microscopy analysis demonstrated that this phylossilicate is finely grained and associated with coarse fractions. Thus, the removal of fine fractions made possible a partial reduction in mica content. Furthermore, intensive attrition demonstrated that the procedure was efficient to remove most of the mica while also reducing sharp edges, which improved the shape of these particles."

Jan 1, 2014

By Paul W. Cleary

"DEM application in mineral processing has for many years been heavily focused on simulating mills of various types. This method can be used to simulate many other aspects of mineral processing operations and can be used both to enhance understanding of the underlying flows and of issues such a breakage, wear, blockage, product degradation, segregation and mixing. The application of DEM to four important classes of non-comminution problems and equipment commonly found in or near mineral processing plants are described. These are:- Particle transport (examples include a conveyor belt and an inclined screw conveyor)- Sampling (assessment of sample bias for cross-stream samplers)- Separation (the efficiency of vibrating screens)- Storage and reclaim (discharge from a multi-port hopper and segregation in a splitter bin with asymmetric ingoing and outgoing conveyor belts, apron feeders and impact plate)."

Jan 1, 2003

By Zhong Hong

A novel ilmenite collector, tert-butyl benzoic hydroxamic acid (TBHA), was investigated in this paper. The flotation performance and adsorption mechanism of TBHA to ilmenite were evaluated through pure mineral flotation tests, ?-potential measurement and IR spectrum analysis. The experiment results indicated that TBHA exhibited strong collecting capability to ilmenite under pH 6.0-8.5. At pH 7.0-10.0, TBHA existed in the form of anionic species in aqueous solution, and the ?-potential measurement results showed the surface of ilmenite maintained negative and more negative after the adsorption TBHA on it, which inferred that TBHA might adsorb on the surface of ilmenite through chemical interaction. The IR spectrum analysis further confirmed the chemical interaction between TBHA and ilmenite surface. Keywords: Tert-butyl benzoic hydroxamic acid, Ilmenite, Flotation, Chemical adsorption mechanism

Sep 1, 2012

By W. Yao, M. L. Li, R. Cui

"The purpose of this research is providing a flotation process for recovery of lead in lead silver residues from a zinc smelting plant with a new hydroximic acid collector (HOC). The collecting ability and reaction mechanisms of HOC were investigated based on pure mineral flotation tests and analysis of zeta potential. The pure anglesite flotation tests showed that HOC has a good collecting ability for anglesite. Zeta potential measurements proved that HOC adsorbed on anglesite surface physically and chemically. The lead-silver residues in a zinc smelting plant with lead grade about 17.5% was used as raw material for flotation tests. The results showed that under the conditions of pH adjusting agent lime 500g/t, inhibitors sodium silicate 2000g/t, collector HOC 1500g/t, frother alcohol oil 75g/t, the grade of the lead concentrate can be reach 47.18% and the recovery was 76.39% by one roughing-one scavenging-three cleaning and middles back to the flow-sheet in turn after the lead-silver residues were washed by two stages of cleaning-filtration.INTRODUCTION Nowadays, with the increasing exploitation of natural mineral resources, more and more secondary resources should be researched and used for the valuable metals. Hydrometallurgical zinc leaching residues, which contain a considerable amount of zinc, lead, silver and other minor valuable constituents, is a typical and abundant secondary resources (Zhang et al., 2011). A huge quantity of zinc leaching residues (ZLR) had been produced per year (Jiang et al., 2017).This residues not only occupy precious land but also threaten the environment because of the dissolved heavy metals especially in rainy days (Han et al., 2014). Consequently, it is urgent to develop an effective and clean method to dispose this residues which can benefit not only in economical but also in environmental (Jha et al., 2001)."

Jan 1, 2018

By A. Zangooi

Frothers play major roles in flotation through interaction at the air/water interface. A method of determining frother adsorption density (coverage), i.e., the number of molecules per unit of interfacial area of bubble surface, is introduced. The technique is based on mass balancing the frother around a continuously operated bubble column. The mass balance requires collection of bubbles before they burst. The column design and operating procedure is reviewed, and some preliminary results discussed. Keywords: flotation, colorimetric frother analysis technique, frother mass balance, coverage

Sep 1, 2012

By G. M. Savov

Copper recovery via Solvent Extraction (SX) process is a well-known technique, which is practiced commercially for approximately 40 years. The main advantages of the SX process are: an absence of using high temperatures (not more than 50oC), complete recycling of barren solutions, very high selectivity at removal and purification of metals, metal conversion to a form, suitable for easy subsequent recovery. Despite the wide acceptance of Solvent Extraction, it does have some shortcomings, namely SX employs large quantities of volatile organic substances. This leads to huge plant ?footprint? of SX circuits. The SX is very sensitive to low temperatures and quantity of total suspended solids in feed solutions and this causes bad phase disengagement times and therefore poor process performance. And most important ? low grade solutions (with copper concentrations below 1 gram per litre) are very unattractive for treatment via Solvent Extraction process, because capital costs for SX plants are not a direct function of copper tenor in the feed. The combined process with Ion Exchange (IX) and Solvent Extraction ? further called IX/SX by IONTECH Engineering was developed. This combination eliminates SX negative characteristics shown above. The key findings of the IX/SX process are; (1) recovery of copper from pregnant leach solutions with metal concentrations, varying on a broad range; (2) can be operate effectively with very low-graded copper pregnant leach solutions; (3) the construction of large ponds for pre-filtration of the pregnant leach solutions is not necessary; (4) working with turbid solutions and solutions containing large quantities of suspended solids; (5) winter operation without troubles; (6) strongly reduces organic losses; (7) technological approach lead to plant sizes reducing. This paper reviews the main stages of the combined IX/SX process, the applications for metal recovery and introduces projects where the process is applied. Key findings of the process are also presented. A comprehensive technical comparison between processes has been carried out. This paper also evaluates the advantages of using combined IX/SX technology as a purification and separation step in copper production process, with the aim of further increasing the overall copper recovery and to ensure that a suitable copper concentration in the advanced electrolyte is achieved. The implementation of a Ion Exchange (IX) process in the classic Solvent Extraction-Electrowinning process(SX/EW) is found to be beneficial for processing of pregnant leach solutions both from spent and new copper heaps and dumps, acid mine drainage and other industrial streams without any preconditioning as well as in terms of achieving improved recoveries and copper cathode quality.

Sep 1, 2012

By Kilian Neubert, Hermann Wotruba, Henning Knapp

Sensor-based sorting has been integrated into more and more applications in mineral processing over the past decades. Various sensor types, such as line scan cameras, near infrared sensors and X-ray transmission sensors, allow the separation of a vast variety of raw materials. Sensor-based sorting has several economic benefits which can make the difference between an uneconomic operation and a profitable mine. Sensor-based sorters can be applied to fulfill various sorting tasks, such as waste rejection, product quality improvement and ore type diversion, and have a significant impact on the layout of the processing plant. Therefore, it is important to include sensor-based sorting into the planning of a processing plant at an early stage. To evaluate the applicability of sensor-based sorting for any specific ore type, it is currently necessary to provide several hundred kilograms of material for subsequent bulk tests. In exploration, ore samples are usually rare and only available in form of drill cores. The acquisition of drill cores is time-consuming and expensive especially for deposits in great depth. Hence, it is unfavorable to spoil valuable drill cores for bulk tests. This paper describes a methodology to evaluate the applicability of sensor-based sorting based on drill core analysis. That methodology offers the possibility to calculate the achievable performances of different sensor types for various grain sizes without comminution of drill cores. The general methodology is shown on basis of an exemplary test work on drill cores from a currently conducted exploration.

Jan 1, 2014

In this paper, the recovery of copper minerals and molybdenite in the rougher/scavenger banks of two separate mineral processing plants is compared with recovery in laboratory (batch) cells. A number of metallurgical surveys were conducted in two plants treating porphyry copper and molyb-denum ore. Batch flotation tests were performed on plant conditioned flotation feed slurry, in parallel with the plant metallurgical surveys. The effect of flotation feed density on recovery of copper minerals and molybdenite in the plant and batch laboratory cells was investigated. Changes in flotation pulp density had little effect on copper mineral recovery, in both plant and laboratory cells. The ultimate recovery for molybdenite, on the contrary, increased considerably when the pulp density was reduced, both at plant and laboratory scale. Recovery of copper minerals in the plant and laboratory cells was comparable, while molybdenite recovery in laboratory flotation cells was 3%~13% higher than in plant. It is hypothesised that the flotation rate of molybdenite is sensitive to cell hydrodynamic conditions (i.e. local turbulent energy dissipation) more than the flotation rate of copper. The flotation behaviour of molybdenite particles is likely to be predominantly controlled by bubble-particle collision frequency, which is enhanced in high local turbulent energy dissipation environment. For chalcopyrite, the flotation recovery is mostly determined by attachment and stability efficiencies. An increase in local turbulent energy dissipation, while increasing collision efficiency, may negatively impact on attachment and stability efficiencies. The outcomes may have a considerable impact on increasing molybdenite recovery from porphyry ores.

Jan 1, 2014

By Leming Ou, Qiming Feng, Yiping Lu, Pengyu Zhang, Qing Shi, Kun Liu, Guofan Zhang

"This paper introduces the mineralogical analysis of certain polymetallic copper-zinc ore in China with the aim of improving the flotation process. The main valuable elements, mineral phases and compositions of run-of-mine ore were inspected by the X-ray Fluorescence (XRF) and chemical analysis. For a deep known of the old process defects, Mineral Liberation Analysis system (MLAs) was employed to investigate the minerals liberation degree of selected key slurry points. Analysis results show that the run-of-mine ore belongs to the original copper-zinc polymetallic symbiotic ore at low oxidative level, which mainly contains 0.16% Cu, 4.43% Zn and 0.88% Sn. Gangue minerals are mainly silicate minerals, and zinc mineral is sphalerite. MLAs test illustrates that about 86% sphalerite has been dissociated in zinc flotation feed. In the current flotation process, over grinding of sphalerite monomer and insufficient liberation of intergrowths are the key problems need to be solved imminently. Up to this point, a new process consisted of two steps roughing unit is submitted in this research. It contributes two positive effects on zinc flotation performance: (i) separating sphalerite monomer timely to decrease overgrinding; (ii) improving zinc minerals intergrowths liberation efficiency. Flotation results indicate that the zinc concentrate grade increased 0.90% and the recovery improved 0.96% in the new flotation processINTRODUCTION Mineralogical analysis mainly focusses on solving mineralogy problems in minerals processing, assisting in minerals behaviors prediction and control for separation engineering (Falkovich, et al., 2001; Hillier, et al., 2003; Schouwstra and Smit, 2011). Process defects searching becomes its ordinary work, and flotation optimization appears to be its targets gradually. For example, Lucky Friday mine company (Idaho America) fails to obtain qualified lead concentrate as the change of ore properties (Nadoll, et al., 2011). Mineralogical analysis ascertains that there are too many dissociated sphalerite, pyrite and gangue particles exist in lead concentrate. According to this, more cleaning units are added to solve problems effectively. Kanowna Belle mine (Australia) takes a flash circuit in operation successfully with the aim of optimize flotation process, under the helps of mineralogical analysis and industrial test (Newcombe, et al., 2013). Lotter N.O. (2011) gives a deep description on how mineralogical data assisting mineral processing engineers to design and optimize flowsheet. For decades, quantitative and automated mineralogy techniques (Andersen, et al., 2009; Gu, et al., 2012; Oghazi, et al., 2009; Yu, et al., 2007) get well developed and hugely improve the veracity and repeatability of minerals properties measurement. Among these, MLAs (Gu, 2003) provided by JKMRC (Julius Kruttschnitt Mineral Research Center) is critically acclaimed all over the world. This analysis system can measure mineral phases composition and content, particles size, minerals occurrence and liberation degree directly."

Jan 1, 2018

By Paul Gottlieb

This paper reviews the status of automated applied mineralogy today and describes the history and fundamental theoretical and practical bases underpinning the development of automated systems. Details are given of the technical challenges that were faced in creating the new technology and in applying it to a range of applications. In recent years, automated mineralogy has become established as an essential enabling technology for the reliable acquisition of statistically sound comprehensive mineralogical and metallurgical data. This has had a revolutionary effect on the industrial use of such data in the study of geology, mining and mineral processing. Previously, using manual methods, it was not feasible to attempt this work because the large data sets required could not be assembled in a realistic timescale. There was a reliance on individual expert mineralogists and this was not scalable. The speed, reliability, detail and repeatability of the modern automated measurements has now made this type of analysis routine. Automated Applied Mineralogy has come of age! More than 100 systems have been installed around the World. Automated mineralogical analysers such as QEMSCAN® were originally developed as diagnostic metallurgical tools to improve mineral processing plants using samples drawn from plant surveys, bench and pilot-scale tests. They were used mainly for the assessment and auditing of size fractions of mill products, such as concentrates and tails. Subsequently, they began to be used for concentrator design and optimisation where ore characterisation was used to help understand the relationship between the feed ore and its subsequent behaviour in the plant. They are now widely used to measure exploration cores and drill chips from drilling programs to predict eventual metallurgical performance. Ore samples can be classified into metallurgical, as well as geological types, by combining mineralogical features in the ores with metallurgical properties related to grade control, separation, comminution, flotation and leaching behaviour. Three-dimensional block models of ore deposits are now being created based on processing response in addition to geological and mining properties. The development of automated systems began in Australia, the United Kingdom and Canada in the late 1970s and early 1980s. There were many technical challenges. Mathematical theories of randomness, sampling theory, image analysis and stereology were developed to ensure sample representivity so that meaningful information could be obtained. Sample preparation, presentation and measurement methods were developed to ensure that the random sampling was preserved during the measurements. Methods of automatic measurement and mineral identification evolved from the use of electron microscopes, fitted with backscattered electron brightness and energy dispersive X-ray detectors. Operational procedures were required to ensure that these instruments could accommodate a large number of samples and operate unattended for long periods of time. The new technology was progressively applied to a range of commodities and applications and new analysis methods, such as liberation measurement, were needed for metallurgical interpretation of mineralogical data.

Jan 1, 2014

The flotation behavior of kaolinite and diaspore using N, N-diethyl dodecyl amine (DEN12) and N, N-dimethyl dodecyl amine (DRN12) as collector have been investigated through flotation experiments. The mechanism of adsorption of two tertiary amine collectors on surface of kaolinite and diaspore were investigated by FTIR spectral, Zeta potentials measurements and calculation of molecular orbital energy. It has been found that DEN12 and DRN12 have stronger collecting power to kaolinite and weaker collecting abilityto diaspore than DDA. Kaolinite and diaspore in bauxite ores can be separated by using DEN12 and DRN12 as collectors at pulp pH below 8 and 6, respectively. The results of zeta potentials and calculation of molecular orbital energy indicated that the adsorption strength on kaolinite surface is in the order DEN12>DRN12>DDA and the adsorption strength on diaspore surface is in the order DDA>DEN12>DRN12. FTIR spectral analysis and Zeta potentials approve that the action between kaolinite and tertiary amine collector is strong electrostatic adsorption and that of diaspore is weak electrostatic adsorption in the range of pH 5~6.

Jan 1, 2014

By M. Abdollahy

Solvent extraction of gallium from Bayer solution of Jajarm Alumina plant was investigated us-ing Kelex100 as extractant. Taguchi experimental design method was used in order to optimize the separation factor of Ga and Al. Optimum conditions were obtained as follows: Temperatuer: 65°C, volume ratio of aqueous phase to organic phase: 3.0:1.0, process time: 60min and organic phase containing 15vol.% Kelex100, 5vol.% isodecanol in kerosene. In this conditions, 74% gallium and 0.3% aluminum was extracted and separation factor was obtained 828.63.

Jan 1, 2014