Search Documents

By Jiang Wenli, Zhang Yimin

In order to enhance the quality of iron concentrate from magnetic separation, reverse-flotation technology is often applied in an iron ore dressing plant.However, this technology has disadvantages in terms of operating cost,energy consumptionand environmental protection(Zhao, Wu& Wang,2005).Developing innovative equipment to process magnetite ore more-effectively is a way to get rid of these disadvantages of reverse flotation and improve the quality of iron concentrate.This paper describes the development of Complex Flashing-Field Magnetic Cleaner,a new kind of equipment based on the principle of combination of separation in magnetic field and separation in gravity field(Hao & Jiang, 2002).This innovative equipment possesses a tailor-made magnetic system and has the characteristics of a magneticfieldwhich can strengthen the formation of magnetic agglomerations and the dispersion of gangue mineralsto improvethe quality of separation.The automatic control system developed specifically for this equipment can further increase the accuracy of separation and stabilize the process.

Jan 1, 2014

By Nirmal Weerasekara, Malcolm Powell, Mohsen Yahyaei

"The conditions under which rocks become superficially damaged during the grinding process are not well understood. The main purpose of the work presented here is to understand how superficial breakage occurs under incremental low-energy impacts. To enable this study a series of abrasion tests with multi-size pilot mills have been performed. Outcomes of numerical simulation corresponding to each test were examined to investigate the experimental results. Abrasion tests have been conducted using three grinding mill sizes (i.e. 1.8, 1.2, and 0.8 m). Two types of ore were used to investigate different hardness strengths. To ensure abrasion was the dominant mechanism, in all tests the mill speed was reduced to 40% of critical speed. The relationship between the Fractional mass loss rate and particle size was investigated by randomly collecting seven tracer particles from sizes -73+63, -53+45, and -37.5+31.5 mm. It was evident from the results that the Fractional mass loss rate of angular particles declines as the particle size increases whereas the Fractional mass loss rate decreases from fine to coarse in rounded particles. Results of Discrete Element Method (DEM) simulations indicate that fine particles experience higher levels of collision energy per particle and this value reduces as the particle size increases and mill size reduces. This explains the higher Fractional mass loss rate of smaller particles as well as the increase in the Fractional mass loss rate as the mill size increases. Linked DEM and experimental data indicates that under these test conditions surface damage attrition is the dominant mechanism. This work suggests that DEM simulation can be implemented to predict the abrasion wear of particles in mills."

Jan 1, 2014

By Cheng Gan, Gui Xiahui, Li Shulei, Cao Yijun, Liu Jiongtian, Wu Lun

Flotation rate constant is an essential parameter in the flotation process. The fine coal sample utilized in this investigation is anthracite from the Shenhuo mine in eastern China. Fine coal flotation rate tests were conducted to compare the flotation rate constant at constant power input with that at gradually increasing power input. Results indicate that the flotation rate constant decreases with the flotation process and increases as the flotation energy is increased. In addition, the flotation rate constant is close to the maximum value. The increasing trend of the flotation rate constant gradually slows down as the flotation energy input increases.

Jan 1, 2014

By Homero Delboni, Mauricio Guimarães Bergerman

"At the regrind or secondary grinding stages of metal ores, usually the concern about the energy efficiency is extremely important. In general, the specific energy consumption at this stage is higher than in the primary stages of grinding. In addition, it has been observed a tendency of finer grinding in the new projects of metallic ores, due to the finer mineral liberation, which leads to an increasing capital and operational costs. In Brazil, during the last 10 years, regrind P80 sizes of approximately 40 to 20 ?m have been necessary in all new iron and copper plants. The use of conventional ball mills, adequate for primary grinding, can result in low energy efficiency with products below a P80 of 50 ?m. This paper presents an overview of the regrind circuits in Brazil that operate with vertical mills and the results of industrial surveys at selected vertical mill circuits. Where possible, comparison is made between the plant results and the design criteria and laboratory regrind tests used for the mill sizing."

Jan 1, 2014

By Atul Kumar Bhatnagar

TATA STEEL is the pioneer in coal beneficiation in India. The first coal beneficiation plant was set up in 1951 at West Bokaro and subsequently in 1953 in Jharia. Over the years more beneficiation capacity was added by setting up new coal washeries in both West Bokaro and Jharia, the coal divisions of Tata Steel. currently the beneficiation capacity available is 8.5 mtp aappx Being a captive supplier supplying the coking coal as per demands of our steel works is challenging in the sense that the intent is to leverage the captive raw material advantage and select the best strategy for maximizing value up to steel making. The beneficiation plants were designed to produce clean coal up to 17% ash. With the demand of increasing productivity at the blast furnace the clean coal ash was lowered. subsequently the processes were audited and efficiency improved. The next challenge was to improve the throughputs in the existing plants to maximize the clean coal production. The upgradation was designed in house and implemented to upgrade the plant from nameplate capacity of 2.1 mtpa to 4.5 mtpa while the yearly production targets were also achieved. The presentation will detail the different phases of improvements, process followed, challenges faced, and the results as achieved in the process. Keywords: coal beneficiation, India, coal washeries, beneficiation plants XXVI INTERNATIONAL

Sep 1, 2012

By Samira Rashidi, Robert Dunne, Raj Rajamani

"High Pressure Grinding Rolls (HPGR) are known for more energy saving, better particle weakening and higher tonnage compared to semi-autogenous/ball mill circuits. These machines are scaled up based on the roll diameter. Therefore, studies in lab-scale HPGRs are always preferred because less weight of feed sample is required to run batch tests. The 50-hp laboratory-scale machine at the University of Utah is the first-ever lab-scale machine designed by late Prof Schönert, the inventor of HPGR. This 200x100 mm [DxL] HPGR is equipped with a robust data acquisition system, which enables running steady state tests using a feed sample as small as 6 kg to 12 kg. This paper presents the HPGR grinding study on two different categories of ores, one hard ore and the other soft. A test series has been performed to evaluate the energy consumption and the relation with size reduction on open multi-pass and locked-cycle HPGR circuits. The effect of feed size distribution and operating conditions has been investigated. Locked-cycle tests result in higher reduction ratio and higher rate of fines (100 mesh, 48 mesh and 28 mesh) generation when compared to open multi-pass tests. Data shows that scale-up trend lines stay consistent even when the circuit configuration and operating conditions are varied."

Jan 1, 2014

By Cristian Melipichun, Leopoldo Gutierrez

The effect of the presence of fine particles of kaolinite and montmorillonite on the induction time for attachment of bubbles to particles of a copper concentrate rich in chalcopyrite was evaluated in this study. The results obtained from induction time measurements were correlated with data of concentrate recovery achieved from micro-flotation experiments. The effect of the presence of fine clays on the stability of air-water foams was also studied through measurements of the foam volume generated in a glass column under different conditions of air flowrate and MIBC concentrations. The experimental results showed that induction time values increased under the presence of fine clays. These data agreed with results obtained from micro-flotation experiments that showed that copper concentrate recovery decreased when clay particles were added. Although a complete explanation for these results is not available, the fact that experimental observations indicated that fine clay particles tend to adsorb on gas bubbles, suggests that the interactions between fine phyllosilicate particles and air bubbles have to be taken into account when studying the effect of clays on froth flotation. Foamability tests showed that the presence of fine clay particles increased the foam volumes only at high additions of clays and low dosages of MIBC. The results obtained at higher dosages of MIBC showed that the foam volumes decreased with the addition of clays under all the experimental conditions tested.

Jan 1, 2014

By Marzio Piller, Girolamo Belardi, Jure Mencinger, Paolo Bozano, Gianni Schena

"The hydrodynamics of the Tri-Flo™, a two stage cylindrical cyclone used in dense media separation, is studied using Computational Fluid Dynamics. The flow field is simulated with an Euler-Euler Volume of Fluid two-phase approach and the Reynolds stress turbulence model.A unique feature of the device is that the separation medium suspension is pumped and introduced tangentially into the two cylindrical compartments while the raw feed is conveyed to the feed hopper and fed at the axial inlet. This feature allows to use less pumping energy and limits the unavoidable production of fines. The Tri-Flo™ complex flow pattern is little known but central to the efficiency of the separation.The velocity field is computed within the two compartments of the separator. The interface of the air-core that forms in the inner axial part of the cylindrical sections is identified and visualized. The numerical results for a reduced-size 100 mm ID Tri-Flo™ are compared against laser Doppler measurements on a transparent acrylic model (Chinè, 1995) operated with water. The robustness of the model and its prediction capability are verified.The possibility to accurately predict the velocity profiles within the vessel and their dependence on the main Tri-Flo™ operating and geometrical variables paves the way to a better understanding of the functioning of the separator, its design improvements and scale-up."

Jan 1, 2014

By F. O. Milovich, V. A. Ignatkina, L. A. Samatova, E. D. Shepeta

"The aim of the research was to increase technological parameters of the flotation of finely disseminated scheelitecarbonate ore using selective reagent regime.In the studies the monomineral fractions of scheelite and calcite; samples of the scheelite-carbonate ore of the Primorsky deposit with the range of the carbonate module 3-65 were used. A carbonate module of ore is the ratio an initial assay of calcite to an initial assay of scheelite. Sodium oleate, iso-decyl alcohol, water glass, calcium chloride, soda or sodium hydroxide as flotation reagents were used. The flotation method in the Hallimond tube and in a mechanical cell, an adsorption method for study the kinetics of adsorption of oleate and isodecyl alcohol and its combinations on scheelite and calcite, IR spectroscopy including ATR to study the composition of surfacecompounds were applied. Selective reagent regime may include two ways - a combination of collectors or a modification of depressants of calcite and other gangue minerals. On one hand the combination of sodium oleate and higher fatty iso-alcohols of fractions C12-C16 in the rough scheelite flotation to reduce the flotation activity of calcite has been studied. On the other hand depression of calcite flotation by calcium chloride with water glass into rough flotation was used; modified the steaming cycle by Petrov's method applying change the concentration of water glass and other. Fatty iso-alcohols can adsorb on the surface of the calcite that reducing the adsorption of sodium oleate and floatability of calcite has been fallen. Their co-adsorbing with oleat on the scheelite surface were support the hydrophobization and flocculation of slime particles of scheelite. Flocculation of the particles of scheelite leads to increased up 3 times of the recovery of scheelite from the slime class, and calcite change up only 1.4-1.1 times it’s recovery.The growth of the carbonate module more than 11 is decreased the assay of WO3 in the scheelite concentrate of selection cycle."

Jan 1, 2018

By Filippov. L. O.

Metallurgical results for the copper-nickel disseminated ores were improved by using ultrasonic treatment. This has been demonstrated by processing of bubble-pulp flow in the reactor zone of a reactor-separator flotation machine. It can be explained by changes in mineral and size composition of the concentrates. Thus, the selectivity of Cu/Ni flotation for different values of the hydrodynamic parameter increases considerably. Additional effect of the ultrasound treatment has been noticed under conditions when the detachment of the gangue minerals from bubbles can be controlled. Reactor-separator has advantages over other types of flotation cells for this purpose. In fact, the weak diameter of reactors make more efficient the ultrasound effect than in conventional impeller or column flotation machines. A combination of ultrasonic treatment with original organization of gas pulp flux in the reactor-separator allows to obtain significant effects in the flotation attachment/detachment subprocesses, enhancing the process selectivity and/or recovery of substances. Increase of total recovery of copper and nickel into bulk concentrate at constant grade is 8.5% for coarse disseminated ores. For copper ore, copper recovery increased by 10% at unchanged grade of 11.7% and nickel recovery gained 17% at the constant grade of 2%.

Sep 1, 2012

By Sanja Miskovic, Manjunath Basavarajappa

Numerical investigation of fluid flow characteristics and mixing efficiency of different impeller designs, based on the mixing characteristics of a passive scalar/tracer, is conducted using CFD for lab scale flotation cells of diameter D and height H equal to 300 mm. Fine computational mesh containing close to 1.6 million cells is used to obtain fully resolved steady state flow field close to the impeller. Unsteady scalar mixing simulations are performed on a relative coarse grid consisting of approximately 450,000 cells. Based on detailed numerical simulations, flows are fully characterized for four impeller designs at two off-bottom clearances C of 50 and 25 mm (D/6 and D/12). Passive scalar is injected from the cell bottom and the time required to attain uniform concentration distribution inside the cell volume is taken as the mixing time by monitoring scalar concentration at four discrete locations. The effect of varying agitation speed and off-bottom clearance on mean flow characteristics is also investigated. The scalar mixing results reveal regions of low mixing efficiency and are used to understand mixing process in greater detail. Through the previous research work, it was found that the main flow pattern undergoes transition from double-loop to single-loop configuration with decrease in off-bottom clearance below a certain critical height for stirred tanks using flotation impellers in the absence of stator. The inclusion of stator is found to alter the mean flow behaviour by preventing the jet from transitioning to axial type flow for lower clearance. Power numbers for different impeller designs are calculated based on the torque generated on impeller blades, and also from the total turbulent kinetic energy dissipation in the overall fluid volume. Power number is found to exhibit a significant dependence on off-bottom clearance based on the CFD results.

Jan 1, 2014

By M. Alvarez-Silva

The control of the amount of chromite reporting to the concentrate during the flotation of UG2 ore is of critical importance since its presence affects the downstream smelting process. It is generally reported that the main mechanism responsible for chromite recovery is through entrainment. This is reflected in analyzing the solids and water recoveries. These in turn are strongly dependent on the froth phase. In the present investigation a laboratory scale column flotation cell was used to investigate the role of the froth phase in the flotation of UG2 ore. Such a device is superior to a standard batch cell since it operates at steady state in open circuit and also allows for a greater degree of flexibility in terms of froth heights. The mass of solids and water recovered in the concentrate as well as chromite (Cr2O3) recovery by size class was determined as a function of froth height, superficial gas velocity and depressant dosage. The results showed that depressants had little effect on chromite recovery but increased the grade due to the depression of gangue minerals. A 60cm froth height always resulted in slightly lower solids, water and chromite recovery than for 30cm. Typically only 20-25 % of solids reaching the pulp-froth interface reached the launder. The relationship between solids and water recovery for a wide range of conditions indicated that chromite is mostly recovered by entrainment. Keywords: UG2 ore, column flotation cell

Sep 1, 2012

By Di Liu, Yongjun Peng

"It was identified that clay minerals adversely affect fine coal flotation through slime coatings. In the study, it was interesting to find that an anionic polymer dispersant, lignosulfonate, successfully mitigated the negative effect of clay minerals in coal flotation using fresh water, but in saline water, it exacerbated coal flotation.In order to understand the mechanisms underpinning the different behaviour of lignosulfonate in coal flotation using fresh and saline water, the adsorption isotherm, and dynamic light scattering (DLS) measurements were conducted in this study. While DLS monitored the molecular conformation change (swelling or shrinking) of the polymer in fresh and saline water, adsorption isotherms enabled polymer adsorbed amount on clay and coal mineral surfaces to be determined. It was found that lignosulfonate adsorbed on the coal and clay mineral surfaces providing effective electrostatic repulsions and resulting in a mitigation of clay minerals from coal surfaces in deionised water. In the presence of saline water, however, polymer molecular conformation changed. Polymer molecules were compressed and adsorbed in form of aggregates. The adsorption amount of lignosulfonate on clay minerals increased in saline water. A low dosage of lignosulfonate could not provide sufficient electrosteric repulsion to disperse clay minerals. Moreover, the high adsorption amount of the polymer on coal and clay surfaces led to a more hydrophilic coal surface, and coal flotation was therefore depressed in saline water. This study provides a new insight into understanding the role of anionic polymeric dispersants in mineral flotation using different quality water."

Jan 1, 2014

By William Conger, Greg Schick

Grinding media consumption is a major cost variable in industrial mineral comminution circuits. Specifically, industrial SAG media consumption results from a combination of surface abrasion wear, media breakage, surface spalling and rejection size from the mill. Three main consumption rates; weight of media consumed per time, per kWh and per weight of ore ground are defined and compared. Recent industrial data has provided an opportunity to relate consumption in terms of weight of media consumed to weight of ore ground (g/tonne) and weight of media consumed per kWh of energy consumed (g/kWh) with SAG specific grinding energy consumed (kWh/tonne). Using relationships developed from this data it is possible to project SAG media consumption in future mineral comminution circuits.

Jan 1, 2014

By Marina Nicolova, Irena Spasova, Plamen Georgiev, Stoyan Groudev

Different strains of "silicate" bacteria were used to improve the quality of kaolin by different ways of treatment. All strains formed large slimy capsules consisting of exopolysaccharides and were related to different species of the genus Bacillus, mainly to B. circulans and B. mucilaginosus. It was found that even a short contact of some hours of well developed cultures of these bacteria resulted in improvement of the bending strength and the other ceramic properties of the kaolin. The improvement was connected with the action of some secreted microbial metabolites such as soluble heteropolysccharides, monosugars and organic acids. The best results were achieved by continuous cultivation of bacteria in the presence of kaolin with a high relative humidity and subjected to periodic stirring.

Jan 1, 2014

By Vincent C. Smith, Agit Singh, Bernard Muller

The control of minerals processing plants is by no means trivial. In order to address some of the difficulties, it was decided to develop and test a model predictive controller (MPC) for a milling circuit. A milling simulator was written to test the MPC controller. Due to the large number of tuning parameters in a controller of this type, an optimising algorithm was written that automatically tunes the controller. Good, robust control was obtained when the controller was tuned using this algorithm. The controller was tested for various scenarios that are often encountered in the minerals processing industry. When problems were encountered, the MPC algorithm was specially adapted to accommodate for these difficulties. Control was further improved by using feedforward control as well as quadratic programming. The movement of the manipulated variables was reduced by using a region of uncertainty that allows the controlled variable to vary within a specified region around the setpoint. Integrators were handled by adapting the algorithm slightly and adding an optional integral error portion in the MPC controller. The performance of the enhanced MPC controller was compared to PI controllers on both the simulator and a commercial plant. The MPC controller showed faster responses with less interaction in both cases.

Jan 1, 2003

By Jun Qiu, Ping Chen, Xianjun Lu

Nitrogen of different forms from wastewater was adsorbed by the natural bentonite and modified bentonite. The effects of adsorption conditions on the nitrogen removal were investigated. The experiment results showed that natural bentonite could easily adsorb ammonia while poorly adsorb nitrate, the organic bentonite modified by octadecyl trimethyl ammonium could effectively adsorb nitrate with the removal ratio increased from no more than 5% to 89%. Two kinds of bentonite were added together to the simulated wastewater which contained ammonia nitrogen of 15mg/L and nitrate nitrogen of 10mg/L, the dosages were 1.0g respectively. Both ammonia and nitrate had significantly decreased on conditions that the oscillation time was 1.0h and room temperature 20?. The optimum pH value for ammonia removal was 7 while for nitrate removal was above 7. The adsorption isotherm fitting results indicated that the Freundlich adsorption isotherm was the better model to describe ammonia adsorbed on the natural bentonite and the saturated adsorption capacity was 10.25mg/L, while the Langmuir isotherm could better describe the adsorption of nitrate on the organic bentonite and the saturated adsorption capacity was 14.35mg/L. Fully considering the interaction between different ions and controlling the appropriate conditions, removing nitrogen from wastewater by adsorption of bentonite is an economic and effective method.

Jan 1, 2014

By F. S. Hoseinian, K. Filho, D. Deglon, T. Souza, M. Safari

"This paper investigates the reverse flotation of hematite in three laboratory flotation cells with very different contacting environments. The main objectives are to investigate the recovery of coarse quartz by flotation and fine hematite by entrainment. The laboratory flotation cells used were the mechanical, oscillating grid and pneumatic cells. The effect of froth height and solid concentration were investigated in the mechanical and pneumatic cells. The effect of impeller speed and energy input were investigated in the mechanical and oscillating grid cells. Froth height results show that coarse quartz particle recovery decreases almost linearly with increasing froth height due to increased detachment of coarse quartz particles in the froth. Fine hematite particle recovery also decreases almost linearly with increasing froth height due to decreased water recovery and associated entrainment. Agitation/energy input results show that coarse quartz particle recovery increases with increasing impeller speed to an optimum, after which this decreases dramatically. The increase is due to improved gas dispersion, generation of smaller bubbles and increased bubble-particle collision and attachment. The decrease is due to significantly increased bubble-particle detachment at higher impeller speeds. The recovery of coarse quartz particles in the OGC is higher than that in the mechanical cell with an optimum at a much lower energy input. Solids concentration results show that both mass recovery and water recovery increase with increasing solid concentrations. The pneumatic cell achieves higher mass recoveries and lower water recoveries than those in the mechanical cell at equivalent solids concentrations and operating conditions. INTRODUCTIONFlotation is a selective process for separating different minerals from each other. The flotation separation efficiency depends on the recoveries of the mineral species by both true flotation and entrainment (Neethling and Cilliers 2009; Wang et al. 2015). Both chemical variables and hydrodynamic conditions within the flotation cell affect the recovery and selectivity of the flotation process. Cationic reverse flotation of hematite is a common method for selective separation of quartz from iron ores to produce pellet feed. The presence of coarse quartz particles in the tailings and fine hematite particles in the concentrate are two major challenges in the reverse flotation of hematite (Vieira and Peres 2007)."

Jan 1, 2018

By G. H. Li

Preparation strontium carbonate with celestite concentrate by flotation is studied by agglomeration-reduction roasting process. It is shown that, the drop strength of green pellet is greater than 4 times?(0.5m) -1 under the balling conditions of moisture of 9% and time of 18~20min. Lignin xanthate obviously improves the ballability of the celestite concentrate due to the increase of surface hydrophilicity, therefore, the balling rate is increased, as well as green ball strength. The drop strength of 7 times?(0.5m) -1 can be obtained when the lignin xanthate dosage is 0.5%~1%. Reduction roasting with anthracite shows that the SrSO4 conversion is 82%~83% for celestite concentrate pellet, under the optimal conditions of roasting temperature of 1100~1150? and time of 30min, and it is 10% higher than conversion of celestite lump under the same conditions. The strontium carbonate are prepared after roasted pellets are leached, purified and carbonated, and the SrCO3 content is higher than 97% , while the content of CaCO3 is less than 0.3%.

Jan 1, 2014

By Janusz S. Laskowski

"Frothers offered by different manufacturers are marketed with some information on their chemical and physical properties (e.g. density, viscosity, color, water-solubility, safety/toxicity, etc.). But frothers are used in flotation to generate fine bubbles and to stabilize the forth, and this information is only provided in a very qualitative description of the visual appearance of bubbles and froths. The terms “powerful” and “selective”, which have been commonly used to characterize frothers, have intuitive rather than scientific meaning.This paper introduces the DFI (Dynamic Foamability Index) plotted vs. CCC (Critical Coalescence Concentration) diagrams to classify flotation frothers (Fig. 1). The frothers characterized by low CCC and high DFI values have properties of strong flotation frothers, while those with high CCC and low DFI values are more selective. The proposed frother classification system, based on simple CCC and DFI measurements, provides, for the first time, a solid ground-work for characterization of the flotation frothers."

Jan 1, 2003