Search Documents

By Jiahua Pan, Yanxiong Mei, Shuqin Liu, Rongfu Pei

Growth characteristics of Co-rich crusts from the Western Pacific have been approached. The thick crust shows 3 structural layers: compact upper layer, porous middle layer, and compact lower layer. The middle and lower layers have obviously different microscopic structure, color, and luster. Preliminary study of Calcareous nanofossils in one crust shows that the crust began to grow since Paleogene. The porous middle layer was formed from late Miocene to late Pliocene (Ca. 0.5 ~ 11.9Ma) and the compact lower layer was formed from late Paleocene to late Oligocene (Ca. 56.3 ~ 23.2Ma). The sedimentary hiatus of a 14.26Ma was observed between the middle and lower layers. The boundary between them to be Oligocene/Miocene (O/M) shows an important message on growth age.

By James R. Hein

Ferromanganese oxyhydroxide crusts (Fe-Mn crusts) precipitate out of cold ambient seawater onto hard-rock surfaces at water depths of about 600-4000 m throughout the ocean basins. Fe-Mn crusts concentrate most elements in the Periodic Table above their mean concentration in the earth's crust (continental plus oceanic crust), except for the major rock-forming oxides and also notably gold and palladium. Tellurium is concentrated greater than any other element relative to its earth's crust mean (about 1 ppb). For example, mean contents of the elements heretofore known to be most enriched in crusts, Mo, Tl, Sb, Co, Mn, Bi, As, Se, and Pb are enriched 100 to 1000 times over their earth's crust mean, whereas the mean Te content in Fe-Mn crusts is enriched about 50,000 times. However, the distribution of Te in the earth is poorly known. Estimates of the mean Te content of the earth's crust range from 0.36 to 10 ppb, with 1 ppb being the most commonly cited mean content (compilations in Levinson, 1974 and Govett, 1983). If we took the highest estimate of 10 ppb, then Te would be enriched in Fe-Mn crusts five times more than the next most enriched element, or 5000 times the estimated maximum mean earth's crust.

Jan 1, 2000

By Irina Melekestseva

The Cu-Zn massive sulfides from the basalt-hosted Semenov-2 hydrothermal field (13°31.13´ N, 44°59.03´ W, MAR) are enriched in Au (22?188 ppm) and Ag (127?1787 ppm) [Ivanov et al., 2008] and elevated contents (ppm) of Se (269?289), Sn (123?125), and Sb (72?75). These may indicate heterogeneous substrate rocks and possible ultramafic rocks. Based on phase analysis, 70% of the gold in the massive sulfides is free. LA-ICPMS analysis has shown that the main carrier of the invisible gold is covellite (22.51? 226.64 ppm). Covellite is also characterized by elevated contents of Se, Mo, Sn, Te, Au, Bi, As, Ag, Sb, Tl, and Pb relative to the primary sulfides.

Sep 14, 2011

By Robert G. Ditchburn

The NW caldera hydrothermal vent field at Brothers volcano, of the Kermadec-Tonga arc, has associated massive sulfide mineralization. This includes an abundance of black smoker chimneys that contain significant concentrations of copper, lead, zinc and gold (de Ronde et al., 2005; de Ronde et al, 2010, under review). [ ] The oldest volcanic massive sulphide (VMS) samples recovered so far from Brothers have been dated using radiometric methods at GNS Science and found to be c. 1000 years old. By contrast, a volcanic cone that has formed in the southern part of the caldera has no associated VMS. Only elemental sulphur and Fe-oxide crusts are present here, samples of which have been analysed for their trace elements. From d34S values of sulfates and native sulfur, and the volume of gas (dominated by CO2 and H2S) discharging at the cone site, elements being deposited here are considered more directly magmatic in origin (de Ronde et al., 2005; 2010 under review). It has been discovered that deep-seated changes in volcanic activity at Brothers affect the NW caldera and cone site simultaneously, though the mineralogy at each site is so very different. Thus, the cone site is being studied to determine if elements being deposited there can be used as predictors of potential future VMS mineralisation as similar sites have been found at other volcanoes along the Kermadec arc and elsewhere. The frequency of these deep-seated magmatic events is considered important in the formation of Cu-Au-rich mineralization along arcs. The analysis of Fe within resulting hydrothermal plumes (surveyed by surface vessels), and trace elements in rock and mineral samples, are used to help determine the influence of magmatic contributions to the hydrothermal system. To verify that plumes are a reliable proxy for hydrothermal events depositing iron on the seafloor, Fe-oxide crusts from Brothers volcano cone have been dated to see if their emplacement coincides with highly Fe-enriched plumes in the water column. The radiometric dating techniques developed for barite-rich VMS, i.e. using 228Ra and 226Ra, were unsuitable for the Fe-oxide crusts because 210Pb was the only isotope detected by gamma spectrometry. Therefore, new techniques using 210Pb, 10Be and arsenic have been established.

Jan 1, 2010

By Peter Halbach

The two HYFIFLUX cruises of the German RV SONNE (SO 99/1995 and SO 134/1998) were organized in the framework of a co-operation between several German universities and two European marine research partners. It is a multidisciplinary program for the study of hydrothermalism with its associated geological, mineralogical, and biological processes in the North Fiji Basin (NFB) in the SW-Pacific. The main achievements of the HYFIFLUX cruises were detailed multibeam Hydrosweep mapping in order to identify the detailed tectonic setting, water sampling at hydrothermally active vents, mineral sampling at inactive sites with sulfide, sulfate, and silica mineralizations, and sampling of basaltic rocks, (Halbach et al. 1999). Oceanic accretion in the NFB is characterized by a double spreading system (Auzende et al. 1994),with one spreading axis located in the median part of the basin (Central Fiji Ridge, CFR) and the second one located immediately west of the Fiji platform (West Fiji Ridge). Most of our investigations were done in the northern part of the N 15° segment of the CFR, which corresponds to area A of our program, area D is located farther south in the NFB and corresponds to the N-S segment of the CFR (Fig. 1). During previous works under the French-Japanese STARMER project, the active ?White Lady? mound and the extinct Père Lachaiseí site were sampled; these samples were studied by Bendel et al. 1993. Here an inactive hydrothermal field was studied, where there were many sediment-covered chimneys in various stages of disintegration, (Bendel et al. 1993). However, the area immediately southwest of the nodal circular basin, which is the triple point junction of the medium-spreading Central Fiji Ridge (about 6 cm/yr spreading rate

Jan 1, 2000

By Mark Vardy, Kasia-Leigh Chidlow, Tim Minshull, Jeorg Bialas, Sven Peterson, Bramley Murton, Alba Gil

Since the discovery of the first black smoker on the East Pacific Rise in 1977 (Francheteau, et al., 1979), the hydrothermal vents, now called seafloor massive sulphides (SMS) deposits, have generated great interest in the geological community, especially regarding their formation and composition. SMS deposits are areas of hard substratum, with high base metal and sulphides content, that form through hydrothermal circulation and are commonly found at hydrothermal vent sites. The high base metal (Fe, Cu, Zn, Pb), sulphur-rich mineral content has interested mining companies, due to their potentially high economic value. Currently, the known SMS deposits do not have the same dimensions as the massive sulphides (MS) found on land (covering just 10s to 100s m2) and pose significant mining challenges (being located in water depths between 800 m and 6000 m), meaning that they do not appear to be economically exploitable at present. However, these deep-sea mineral resources could be important targets in the near future, particularly with our ever-increasing demand for base metals. A key aim of the European Union-funded Blue Mining project is to develop techniques to robustly quantify SMS deposits dimensions (both surface expression and subsurface extent) and therefore assessing the suitability of SMS deposits for future economically viable and environmentally clean deep-sea mining operations.

Jan 1, 2017

By K. T. Damodaran

The Chavara and Manavalakurichi placer deposits have been known since a long time for their rich reserves of heavy minerals like ilmenite, rutile, monazite etc. While detailed work has been conducted on the mineralogy and texture of the bulk placer sediments, reports on the detailed investigations on individual minerals are relatively scanty. Though, limited work pertaining to the chemistry of ilmenite has been carried out by Nair et al (1995) and Ramakrishnan et al (1997), a comprehensive study of the weathering patterns of ilmenite along the longitudinal and vertical profiles has not been, so far, undertaken. Data on the microscopic analysis of ilmenite from the southwest placers, too, is sketchy. The present work deals with the variation of the weathering undergone by ilmenite in the southwest placer deposits based on chemical and mineralogical analyses.

Jan 1, 2002

By Karsten Hagenah, Tor Jensen, Jens Laugesen, Øyvind Fjukmoen, Lucy Brooks

"The methods and technologies to be used for environmental monitoring of seabed mining activities are a key issue. Due to the large water depths, there are special challenges with respect to the monitoring equipment that is suitable. DNV GL has built up substantial experience of environmental monitoring from oil & gas projects in deep waters in the Norwegian Sea.Monitoring equipment and experiences from the oil & gas sector can to a large extent be applied to seabed mining.BackgroundThe International Seabed Authority is currently developing an environmental management strategy for the Area (ISA, 2017) as a part of the work on the regulations for exploitation for mineral resources in the Area.The draft environment strategy contains provisions related to monitoring and reporting of the activities. An Annex (Annex III) of the draft document describes the format and content of the environmental management and monitoring plan.The monitoring plan should contain, inter alia: ?Technology to be deployed.?Monitoring frequency of respective elements/components of the Marine Environment.?Monitoring procedures required to implement the Monitoring programme.?Details of the environmental monitoring stations across the Environmental Impact Area.?Monitoring specifics e.g. water quality; sedimentation rates; sound; plume extent; etc., as well as relevant Environmental Targets.?Monitoring of Mining Discharges.?Processes for Monitoring reviews and Environmental audits."

Jan 1, 2017

By Roger Amato

The 1982 United Nations Convention on the Low of the Sea includes provisions under Article 76 for extending a coastal State's jurisdiction beyond the 200-nautical-mile (nm) Exclusive Economic Zone (EEZ) and for establishing the seaward limits of sovereign rights over natural resources. Article 76 prescribes a set of methodologies for determining these outer limits based on physiography and sediment thickness. The methodologies were applied to each of the five continental* margin areas of the United States - Atlantic, Pacific, Gulf of Mexico, Alaska, and Pacific Islands-using existing digital hydrographic and geologic data. Figures 1 and 2 show the results of applying the methodologies to the Atlantic, Pacific, Alaskan, and Gulf of Mexico continental shelves. Figure 1 depicts the preliminary limits of each of the Article 76 determinations for the Atlantic and Gulf of Mexico continental shelves. The Atlantic limits were described by Carpenter, Thormahlen, and Amato (1995) at the 26th Underwater Mining Institute.1 The limits for the Alaskan continental shelves are shown in Figure 2. Additional areas beyond the 200 nm EEZ are highlighted. These include a small area north of the U.S. - Canada boundary, containing 7,000 km2, a large area north of Point barrow (395,000 km2), and a third area north of the Aleutian Islands (178,000 km2). The shelf between the first two areas appears to have sediments thick enough to qualify for the 1 percent method (Irish Formula); however, year-round ice cover has prevented acquisition of seismic or drill data. The entire northern Alaska shelf is prospective for petroleum The Gulf of Mexico (Figure 1) has two small areas beyond the EEZ known as "doughnut holes." One is south of Louisiana and includes part of the Sigsbee Escarpment, an area believed to have potential for oil and gas. Oil was found on Sigsbee Knoll in cores from Deep Sea Drilling Project's Leg 1 cruise in 1968. The Sigsbee areas contains about 6,000 km2. The second area is south of the Florida panhandle and contains about 12,000 km2.

Jan 1, 1996

By André. C. Louw

Diamond production from the reworked beach and river channel gravels along the west coasts of South Africa and Namibia is well known throughout the world, not only for the exceptional quality of the diamonds, but also for the sheer scope of the operations. To date an estimated 140 million carats have been produced from the resource worth some US$40 billion in today's money terms. It is therefore not surprising that it didn't take long before the attention turned towards the possible extension of this valuable diamond resource on similar submerged beaches in the adjacent territorial waters of South Africa and Namibia. This has proved to be a very successful move as the marine production in Namibia today constitutes 48% of that country's total diamond production. Although small scale recovery of diamonds from the sea commenced in the 1950's, the first large scale production came from the operations of the Texan entrepreneur, Sam Collins, in the 1960's. The De Beers Group, which took over Sam Collin's operations in 1969 had all the concession areas, as well as the financial and human resources to tackle the new mining frontier in the correct way by years of data gathering (ie diamond reserves and seafloor terrain studies) before commencing with large scale mining operations in the 1980's. Those who are familiar with the beach mining operations along the South African and Namibian west coasts will have appreciation for the daunting task of surgically removing the payable portion of diamond deposits from the non-payable material on the one hand, and the complex uneven fractured and gullied bed-rock floor of the deposits on the other hand. Not to mention the additional complexities of large boulders and hard calcretised diamond gravel layers (conglomerate) which are sometimes associated with the deposits. It was a natural development that the sea diamond mining operations were approached with the known information of the land operations, attempting to duplicate land mining operations in the sea, but taking cognisance of the variations of the terrain in the different areas. For instance, we encounter the following variations, and combinations, off the Namibian Coast. ? Close inshore - holocene sand cover often masks large areas of potentially diamondiferous gravels. ? In midwater areas (40m - 100m)

Jan 1, 1998

By H. I. Chesalova, M. Ye. Melnikov, A. M. Asavin

The discovery of iron-manganese ores on the surface of underwater mountains was made more than a half century ago. During this time the basic ideas about the thermodynamics of the processes of hydrochemical reactions in the sea water have been developed by scientists and are revealed in geochemical and mineralogical differences between the deposits from the seamounts and the nodules of the sea bottom. The distribution of the dissolved metals, oxygen, carbonic acid and organic matter in the overlying ocean waters of seamounts in the deep ocean to depths more than 5,000 m has been studied in some detail (e.g. J.R. Hein, P. Halbach. G.B. Baturin, Ye.M., S.I. Andreev, L.I. Anikeyeva, [1-6]). In recent years scientists from YUZMORGEOLOGY have completed detailed geological survey work on the Magellan Seamounts in the Pacific Ocean. The results of drilling the ore body and geophysical and photo surveys have also been described [4]. Previous ideas about the general covering of seamount surfaces with iron-manganese crusts have been changed based on ground-truth surveys. This study examines the complex concentric-zone or spotty arrangement of the most densely covered sections, the strong dependence of the thickness of crust on the geomorphologic features, and the potential influence of the underlying substratum. One established geochemical heterogeneity in the composition of ores, also frequently inversely proportional power dependence on directions was observed. The development of a numerical model of the formation of the ore crust on the seamounts is currently a high priority.

Sep 24, 2006

By Stephan K. Schwank

In mid 1993, Bauer Spezialtiefbau GmbH, based in Germany got the order to develop a sampling tool capable of penetrating all different types of seabed sediments including cobbles and boulders and into bedrock. BHP and their partners Benguela Concessions Ltd., had been convinced by the Bauer Trench Cutter Technology and a large scale test in Germany that this system will be the right one to fulfill their expectations for sampling the diamond area off the coast of Namibia. The technique of the tool is based on Bauer's standard cutter technology, which is widely used for the installation of cut-off and diaphragm walls all around the world. The two counterrotating cutter wheels with 12.1 tom torque each cut an area of 3 x 1.2 m (up to 3 x 3 m are possible). The material mixed with seawater was then pumped to the separation plant on board the vessel Geomaster with a capacity of approximately 700 m3/h. Cutter wheels and mud pump were mounted on a special cutter frame and connected by wire ropes and hydraulic hoses to the vessel. An outer frame with four telescopic legs supported the cutter vertically on the uneven seabed and allowed a controlled penetration of the tool up to 6 m into the diamond bearing ground. The tool required a total power installed of approximately 800 kW. All hoses, the 6-inch mud hoses as well as the hydraulic hoses, were stored and compensated on drums on board suitable for a water depth of up to 200 m. Launch and recovery of the tool was effected through the moon pool of the vessel and the 25 m high, special designed drill tower. The 65? to sampling tool had been commissioned in early 1994 in Cape Town. After intensive testing the sampling programme of more than 4000 holes could be successfully completed by January 1995.

Jan 1, 1998

By Derek V. Ellis

This article is a summary, with documentation and references, of recent global developments in identifying environmental issues affecting the marine mining industry. It is recognised that marine mining for various products occurs at various depths from shallow water (e.g. aggregate and diamond mining) potentially to great depths (e.g. metalliferous muds, and manganese crusts and nodules). Nevertheless there are environmental issues in common, even though the options for resolutions will vary greatly. The point of this review is to identify the issues, so that where site-specific resolutions are considered, it is possible to draw on experience with the issues elsewhere. Related mining issues, e.g. tailings effluent quality, orebody geochemistry, are mentioned where relevant but are not detailed in this article, although obviously they are a part of there solutions to the environmental issues. The environmental issues and their resolutions are important - on the basis of the ethic of not creating more impact than is inevitable, and the long-term financial and social costs at a mine-site of not getting the resolutions right.

Jan 1, 2000

By Sup Hong

A pilot mining robot, named MineRo-II, has been developed by KIOST during 2011-2012. The pilot scale was defined as 1/5 of the commercial mining capacity, 1.5 million dry-tons of nodules per year. The development purpose of MineRo-II is to use for the pilot mining test planned in 2015. MineRo-II was designed to be self-propelled by electric-hydraulic power and remotely operated in real-time from aboard. The main operational functions are crawling on seafloor, pick-up and crushing of nodules, discharging nodules out to buffer. Prior to MineRo-II, a test miner (MineRo-I) was developed in scale of 1/20th in 2007, and performed two times sea trials in 2009 and 2010. The results of performance tests were evaluated and utilized for the concept of MineRo-II. The design concept aimed at the expandability of the mining capacity based on modularity of configuration, maintenance simplicity and multiplicity of backup solution. The pilot-scale mining capacity is achieved by four pick-up modules of each 1m wide, which are moving forward with robot vehicle and sweep the nodules entering below the pick-up heads. Principally, by adding the pickup modules in lateral dimension the mining capacity may increase linearly. MineRo-II was designed and constructed in unit-module wise. The robot consists of two unit-modules having an identical mechanical and hydraulic configuration. Each unitmodule has two tracks, two pick-up devices with attitude control devices, two crushers, one discharge pump, and one hydraulic system. Two unit-modules are connected by one loading frame and integrated by electric-electronic system. Two thrusters for control of the

Sep 14, 2011

By James R. Hein

Rodriguez Seamount, located 150 km off the central California coast at the base of the continental slope, was studied using the ROV Tiburon aboard MBARI?s R/V Western Flyer, October 13-16, 2003. Fe-Mn crust and rock samples were collected along the SW flank of the seamount at water depths from 700 to 2100 m; bottom-water dissolved oxygen content (O2) and temperature were determined at each sample site. Fifty-three samples of bulk crusts, crust layers, and surface scrapes (~0.5 mm) were analyzed for 59 elements. Data allow for the correlation of crust compositions with precisely known water depths and seawater O2 measured at the actual site of sample collection. This is the first detailed study of Fe-Mn crust compositions in a region of strong continental-margin upwelling. Compared to open-ocean seamount Fe-Mn crusts, Rodriguez crusts have significantly higher (2-6 fold) mean concentrations of Fe (26.9%), Al (1.65%), Si (13.0%), Cr (82 ppm), Th (64 ppm), and Ag (1.7 ppm); and significantly lower (2-8 fold) mean concentrations of Ca, P, Bi, Co, Cu, Ni, Tl, and especially Te (8.2 times lower). All but one Fe/Mn ratio are >1 compared to <1 ratios for open-ocean crusts. O2 contents (0.35-2.03 ml/L) are nearly perfectly corrected with water depth and elements correlated with one are correlated with the other. The Fe-Mn surface scrapes represent 60-450 ka (mean 150 ka) of growth, whereas the dissolved oxygen contents of seawater represent an instant in time. Assuming that the entire sample set was affected uniformly by oceanographic changes, we suggest that correlation of elements with O2 may reflect oceanographic processes. O2 has a negative correlation with P, V, As, Fe, U, Be, Pb, Cr, Mg, Y, Bi, Te, and REEs (except Ce) and a positive correlation with aluminosilicate-hosted elements (Al, K, Rb, Cs). This later relationship is related solely to water depth, indicating that detritus shed down the seamount slopes accumulates in greater abundances in deeper-water crusts. Si/Al ratios indicate that the detritus includes a large component of biosilica produced by upwelling-mediated high productivity. These observations are supported by positive correlations of aluminosilicate-hosted elements with crust growth rates (range 1.2-13.0 mm/Myr). In contrast, other elements (Sr, Co, Mn, Mg, Te, As, Mo, V, W, U, Ti, Ni, REEs, etc.) are negatively correlated with growth rates. Growth rate has a weak positive correlation with O2. These compositional characteristics indicate that even though low-O2 seawater acts as a reservoir for Mn and associated elements and produces slow growth rates, which would allow for the concentration of elements and surface oxidation processes to occur, the high rate of input of detritus and high bioproductivity ameliorate the strong concentration of most metals. This dilution is significantly enhanced by the doubling of FeOOH in the crusts--the main cause of the generally high growth rates compared to open-ocean crusts. The high growth rates limit the oxidation of Co, Tl, and especially Te on the crust surface, which is reflected by their relatively low concentrations. Within the range of oxygen contents measured, O2 has less of an influence on crust chemistry than does the availability and incorporation of FeOOH and detritus.

Jan 1, 2004

By Carl L. Kaiser

This abstract discusses selected recent technology developments at the Deep Submergence Lab at the Woods Hole Oceanographic Institution aimed at fundamentally changing the nature and scope of AUV operations in the deep ocean. The Autonomous Underwater Vehicle (AUV) Sentry is described in its current configuration with discussion of emerging capabilities. Telepresence enhanced AUV operations are discussed including moving both operations and data processing personnel off the vessel. Autonomous Surface Vessel (ASV) aided AUV operations are discussed including recent experiments where an ASV provided both navigational aiding and a satellite based relay for acoustic communication of telemetery and mission redirection. New flexible communications strategies to perform intervention and manipulation tasks from an untethered vehicle are discussed. The abstract concludes with a brief discussion of industrial collaborations, including the newly launched Center for Marine Robotics.

Sep 14, 2011

By Rolf B. Pedersen, Filipa Marques

The extension of the Mid-Atlantic Ridge north of Iceland has collectively been referred to as the Arctic Mid-Ocean Ridges (AMOR). The AMOR extends from the northern shelf of Iceland, to the Siberian shelf in the Laptev Sea, passing en route through the Norwegian- Greenland Sea, the narrow gateway of the Fram Strait, and across the Eurasia Basin. The AMOR is 4000 km long and is divided into six super segments: 1) the Kolbeinsey Ridge, 2) the Mohns Ridge, 3) the Knipovich Ridge, 4) the Molloy Ridge, 5) the Lena Trough, and 6) the Gakkel Ridge. After continental rifting at 60-50 million years ago, around 2.5 million km2 of oceanic seafloor has formed by seafloor spreading - resulting in the formation of the Norwegian- Greenland Sea and the Eurasian Basin. This northernmost part of the global ridge system is anomalous in several ways: The seafloor spreading takes place at an ultraslow rate (less than 2 cm/y) with spreading rates decreasing northward to around 1 cm/y at the Gakkel Ridge - which is the most slow-spreading ridge on Earth. As a result, the volcanic activity along the northern part of the AMOR is low, the oceanic crust is unusually thin (around 3,5 km at the Knipovich Ridge, Kandilarov et al.2010), and the rift valley is deep (average water depth > 3 km). In the southern part of the AMOR, the ridge system is affected by the Icelandic plume and a hot spot below Jan Mayen. The ridge-plume interaction results in higher volcanic productivity, unusually thick oceanic crust (9-11 km, Kandilarov et al. 2012) and shallow ridge segments (1500-100 m). The AMOR also display contrasting spreading regimes, whereas some super segments are dominated by orthogonal spreading (Kolbeinsey and Gakkel Ridge) others are characterized by highly oblique spreading (Mohns and Knipovich ridges). Some ridge segment displays asymmetric spreading, like the Mohns Ridge where core complexes preferentially form along the northwestern flank. Together these variations in ridge characteristics results in large diversity of hydrothermal systems and associated mineral deposits.

Jan 1, 2018

By Timm Schoening, Greinert. Jens, Iason –. Zois Gazis

"Ferromanganese nodules are again of interest because of their high concentrations of Ni, Co, Cu as well as REE. With regards to an operational underwater mining industry, one of the main questions and important requests is to finding a method that can predict the abundance of nodules with high accuracy within reasonable time spans, without many requirements for ground truth data; and all these on an operational scale and ideally automated. In this regard, we present results of a study based on the combination of highresolution multibeam and optical data acquired by an AUV using specific machine learning techniques to reveal a detailed distribution of the Mn-nodules in correlation to the seafloor terrain. The accuracy of the method employed and results gained were validated and approved through comprehensive statistical analysis and by comparison to box-core data.Study AreaOur study area (AUV survey block G77) is located in the Clarion-Clipperton Zone (CCZ) (Eastern Central Pacific Ocean), an area that has been receiving international research and industrial attention for many years already (e.g. McKelvey et al., 1979; Bernhard and Blissenbach, 1988, von Stackelberg and Beiersdorf, 1991, Jeong et al. 1996). Block G77 covers an area of 9.5km2 in a depth between -4478m and -4536m. The area is characterised by gentle slopes 0-5° (0-3° in most of the area and only in the outer parts of the Block slopes can exceed 5°). The seafloor is characterised by moderate to low rugosity, the only exception being a small area in the eastern part, where sub-recent smallscale volcanic activity created 15 cone-shaped morphological features of up to 55m height and 150m width that are clustered in an area of 700 x 380m (Figure 1)."

Jan 1, 2017

By Carsten Rühlemann, David Friedmann, Bernd Friedrich, Thomas Kuhn

"This paper explores the option of direct reduction smelting of the nodules from the German license area in the equatorial NE Pacific in a submerged arc furnace (SAF). An optimized slag design is proposed to separate the larger Mn-bearing stream from the valuable metals (i.e. Ni, Cu, Co, Mo). The slag optimization allows a maximum of Mn to be retained in the manganese-silicate slag on the one hand and a maximized metal recovery in a FeNiCuCo alloy on the other. This way, the goal is to make use of the complete nodules (“zero-waste”) instead of extracting only the metals Ni, Cu, and Co, which make up about 3 wt%. The process closely relates to the “Inco Process” by the Ocean Management Inc. (OMI) of the late 1970s, which was a consortium of INCO (International Nickel Company, CAN; today Vale Canada), Preussag AG & Metallgesellschaft AG (GER), DOMCO (JPN), and Sedco (USA). However, the manganese containing slag is investigated in more detail to recover FeMn, FeMnSi and/or SiMn. To optimize the process modern tools such as thermo-chemical modeling in FactSage™ have been used. [1,2]Polymetallic deep-sea manganese nodules may offer a decreased dependency of raw material imports for Germany and the EU. Currently, four European countries (United Kingdom, Belgium, Germany, and France and an Eastern European consortium (InterOcean Metal)) hold exploration licences for these nodules in international waters in the equatorial NE-Pacific. The license areas each cover 75 000 km2 of the seafloor and are located in the Clarion Clipperton Fracture Zone (CCZ) south east off Hawaii at water-depths between 4000 and 6000 m. The nodules may be used as a resource for industrially important metals such as Cu, Ni, Mn as well as for technology metals like Co, Mo, V and Zn. The average chemical composition of nodules from the German license area is presented in Table 1. [3,4]"

Jan 1, 2017

By D. S. Cronan

Studies on polymetallic manganese nodules and Co-rich crusts in the EEZ&apos;s of the Cook, Line, Ellice and Phoenix Islands between 0-20°S show that Ni and Cu reach their greatest combined abundances of over 2% between 2-8°S on the southern margin of the equatorial zone of high biological productivity, as a result of biological fluxing of Ni and Cu to the nodules at and just below the CCD. By contrast, Co reaches it greatest abundance of 0.6% south of 8°S in nodules on non-biogenic clays well below the CCD where little biological Co supply is likely. Nodule abundances are greatest (up to 30kg/m2) in the Co-rich area in part due to AABW flow, giving highest overall metal quantities per sq meter in the nodules there, particularly of Co. There are approximately 110 x 106 tonnnes of combined Ni plus Cu plus Co expressed as Ni equivalent in Cook Islands EEZ nodules, approximately 12 x 106t. in Phoenix Islands ones, and approximately 1.4 x 106 t. in Ellice Islands ones, in areas of greater than 5kg/m2 nodule abundance. In the Co-rich crusts, Co averages about 0.7% and crust thickness about 1.6cm, both related to metal fluxes in and adjacent to the 02 minimum zone in association with which both maximum thicknesses and Co grades occur. Within the Cook Islands permissive area there are about 930 x 103 t. of Co and 630 x 103 t. of Ni in crusts, in Phoenix Islands crusts there are about 69 x 103 t. of Co and 55 x 103 t. of Ni, and in Ellice Islands crusts there are about

Jan 1, 1989