Search Documents

By Peter E. Halbach, Andreas Jahn

"Co-rich ferromanganese crust deposits exist on slopes, summits and platforms of seamounts and guyots throughout the global oceans, where deep-sea currents have kept the seafloor structures more or less free of sediment for millions of years. They form by direct precipitation from cold seawater under more or less oxic conditions and consist of thin layers (2 up to 25 cm thick) covering hard substrate rocks in water depths of 800 to 5000m (Halbach and Marbler, 2009; Hein et al., 2000). Besides Mn these crusts contain interesting concentrations of minor elements (Co, Ni, Ti and Cu) and trace elements (Mo, W, Te, Ga, Pt and REEs), thus they represent significant metal deposits and promise potentially valuable additions to the world’s metal resources.The prospects for mining of this marine type of metal deposits largely depend on the grades and the scale of the potential ore resources. However, only a few percent of existing seamounts and guyots have been mapped and sampled in detail, most of them in the Pacific Ocean. Therefore, a model to estimate the geological resources based on the global seamount catalogue of Wessel (2001; revised: Wessel et al., 2009) and the empirical parameters which control the metal composition and distribution was developed."

Jan 1, 2017

By Alexander Malahoff

Mineral zonation studies were conducted on hydrothermal vents of two hot spot volcanoes. One study site is located within the Axial Caldera of the axial hot spot volcano of the Juan de Fuca Ridge. The young high-temperature hydrothermal vent field consisting of two polymetallic sulfide chimneys, five meters high, located at 130°01.5'W, 45°56.5'N, along a fault complex at the base of the southwestern wall of Axial Caldera was sampled during four ALVIN dives in 1983. Temperatures of up to 270°C were measured within the orifice of one of the chimneys, which was then broken off and recovered with the submersible. Both black and white "smoke" was observed to be emanating from the one chimney sampled. The high-temperature chimney extends directly from a field of broken lobate lavas which are located at a water depth of 1,550 meters, about 200 meters east of the caldera wall. The chimney makes one of the shallowest active high-temperature vents studied to date. The vent is surrounded by clumps of vestimentiferan worms and is located within an elongate field of red-colored iron smectite blankets and chimneys. The low-temperature field forms a ribbon 150 meters wide, extending for about 1,300 meters at the base of the wall. Chemical analyses of the hydrothermal deposits ranging from the polymetallic sulfides of the chimney to the outer zones of the low-temperature field show a range of elemental assemblages consistent with temperature zonation around the vent. Chemical zonation within the high-temperature

Jan 1, 1988

By William Siapno

Manganese nodules, as metal ores, have for the most part been cast aside from further consideration within this century. However, in the decade of the 90s, rising demand at all levels of society, for clean air give nodules a new - lease on life as a stack gas cleaning agent. Further, the Clean Air act of 1990, mandates enormous outlays to bring systems into compliance with new stringent standards. Quick corrective actions are imperative. Research beginning in the 1960s proved nodules possess unique qualities to remove acid compounds from stack gases. Early this year, the National Science Foundation awarded General Electric an $83 million contract to design a system to extract oxides of sulfur and nitrogen from coal fired power plants. Environmental damage is abundantly evident on the ground, from the air as well as form space. A dirty pall of yellow-brown smog is smothering both animal as well as plant life around the globe. Losses run into billions!

Jan 1, 1991

By D. J. Scarratt

Fisheries make a significant regional contribution to the economy of Canada. In the Atlantic Region, over 70 thousand workers depend on the primary or secondary fishing industry. Fisheries are vulnerable to pre-emption of space by other marine industries and to contamination by chemical discharges. Markets may be affected even by the threat that products may be tainted. Fish may be killed by drags and dredges, and their physiology and behaviour affected by suspended sediments are stirred up by mechanical devices. Virtually no evidence exists of adverse impacts £ran ocean mining on fisheries, but projections from other marine activities such as fishing itself, dredging and other marine discharges give reason for caution. Department of Fisheries and Oceans policy calls for review of ocean mining proposals to ensure adequate protection of fish stocks, fishing activities and fish habitat, and compensation for losses attributable to any industrial project. Adverse impacts can be minimized by careful attention to details of location, technology and timing, and to close co-operation and information exchange between industry and the regulatory agencies.

Jan 1, 1985

By Tony van der Steen

Subsea mining system are designed for the following, principally different, tasks: Dreding - The destruction and removal of seabed sediments overlaying the bedrock. Cleaning - The competence of the system to systematically remove the deposits from an undulating hard bedrock with irregular pulleys, channels and fissures. Factors that influence the choice of dredging equipment for a specific project are project requirements such as environmental conditions, location and water depth. However, the most important selection criteria are soil conditions. As a consequence, possible dredging systems, must be evaluated for the following, principally different, characteristics: Dredging proficiency - The destruction of the strata by the equipment. System stability - The capability of the soil to support the subsea equipment The above parameters are determined by the strength characteristics and the bearing capacitv_ of the soil. The author describes the processes involved in excavating the subsea deposits and (transporting the gathered soil as a water-soil mixture to the surface using different excavation and transport methods.

Jan 1, 1998

By In Kwon Um

The XRF Core-Scanner system performs non-destructive analysis of elements from Mg to U, in concentrations of ppm levels on split cores with digital images. Using the AVAATECH XRF Corescanner system, we conducted high resolution element analysis of deep sea sediment cores from Clarion-Clipperton fracture zone of the northeastern Pacific to reveal recent environmental changes. Comparison of data estimated by the XRF core scanner with ICP-AES showed relatively weak correlation coefficients except Mn contents. Down-core variations of most elements seem to be matched with each other and reflect changes of sediment colors. Especially Mn/Al ratio significantly change at distinct color boundaries. The variations of Mn/Al ratio with sediment colors are suggestive of changes in redox condition and further divided into two types probably affected by activities of benthic organisms. Be isotope age datings of select core (BC08-02-13) indicate that the color boundaries are approximately coincident with late Pliocene and Pleostocene also early Pliocene and late Pliocene boundary. Keywords: XRF core scanner, High resolution, C-C zone

Jan 1, 2011

By Gordon B. J. Fader

A regional assessment of the aggregate potential of the Scotian Shelf is presently being funded through a Canada-Nova Scotia Cooperation Agreement on Mineral Development. This assessment includes testing of seabed materials for their suitability in a variety of concrete, asphalt and other specialized applications. The glacial and postglacial Holocene history of the Scotian Shelf has been favourable for the formation of large deposits of sand and gravel that have potential for use as marine aggregate resources. Large banks and inner shelf areas of the seabed consist of basal transgressive sand and gravel of the Sable Island Sand and Gravel Formation. These sediments accumulated during the late Wisconsinan postglacial transgression, through sorting of glacial materials that were originally deposited beneath marine terminating glaciers. Some sandy deposits occur as low-stand deltas on the inner shelf at 70 m water depth and were formed during the maxi- mum low sea level stand, in early postglacial time, at approximately 12 000 yBP. Modern sediment transport processes have contributed to the formation of areas of large sand bedforms, such as the Cape Split sand wave field and other isolated sand waves of the inner Bay of Fundy, and Eastern Shoal on Banquereau. Sandy sediments, found in many transverse channels in the nearshore, offer a potential for placer gold where proximal to adjacent onshore epithermal gold deposits. Lithothamnion covered gravel occurs as a thin lag overlying glacial sediments in much of the nearshore. Relict gravel beach ridges have been eroded and redistributed through sub-littoral processes after passage of the transgressing beach front. Multibeam bathymetry, sidescan sonograms and high-resolution seismic reflection profiles are the main survey tools. Ground truth consists of large volume seabed samples, vibrocores and photographs. A preliminary assessment of the aggregate potential indicates that very large volumes of suitable aggregate lie in the offshore of southeast Canada.

Jan 1, 1995

By G. B. Carpenter

The United Nations Law of the Sea (LOS) Convention includes provisions (Article 76) for establishing the outer limits of a coastal State's continental shelf and for denoting the seaward extent of sovereign rights over natural resources. Determination of a coastal State's continental margin, according to Article 76, must consider eight factors: 1. The territorial sea baseline 2. The 2,500-meter isobath 3. The foot of the continental slope 4. A line 200 nautical miles seaward of the territorial sea baseline 5. A line seaward of the foot of the continental slope connecting the points where sediment thickness divided by distance to the foot of the slope equals .01 6. A line 60 nautical miles seaward of the foot of the continental slope 7. A line 100 nautical miles seaward of the 2,500-meter isobath 8. A line 350 nautical miles seaward of the territorial sea baseline Figure 1 shows the preliminary limits for each of the Article 76-based definitions for a portion of the U.S. Atlantic continental shelf. The additional areas gained beyond the 200- nautical mile Exclusive Economic Zone (EEZ) are highlighted. The first three factors are baselines from which the distance provisions of Article 76 are measured. Factors 4-8 are distance- from-baseline provisions for establishing the continental shelf limits. Factor 5, also known as the Depth of Sediment Limit or "Irish Formula", was calculated using sediment thickness data from seismic linesand isopach maps. All other factors were determined from digital hydrographic data. The Depth of Sediment Limit is the most advantageous method for the area shown in Figure 1. It is especially useful for introverted coastlines such as the Georgia Embayment and New York Bight areas. The 200-mile line is advantageous for protruding coasts such as those off major capes, e.g., Cape Hatteras. The 2,500-meter isobath plus 100-mile line gains

Jan 1, 1995

By William J. Scott

In the last two years, C-CORE has developed a new seabed sampler directed specifically at obtaining samples from hard or compacted bottoms such as are typical of marine placer deposits. Samples are required for appraisal of concentrations of saleable commodities, and for determination of levels of biological indicators in the deposits. Recently C-CORE and the University of Victoria have been comparing the performance of the Scott/C-CORE sampler with that of the Van Veen sampler often used for biological sampling. Initial trials of the Scott/C-CORE sampler in 1992 at the WestGold mining site, Nome, Alaska, were described by Jewitt et al. at the 1993 UMI. Since that time the sampler has been modified to prevent overfilling, and to limit turbulent flow of water across the top of the sampler buckets when the sampler is recovered with partly-open buckets. The modifications included shoes to prevent sampler overfill, and flexible rubber shielding over top and sides of the sampler to prevent water circulation. Samples have been taken with both samplers in two field areas, one at Pine Cove, Baie Verte, Newfoundland, and the other near Long Pond in Conception Bay on the Avalon Peninsula, Newfoundland. In each area multiple samples were taken with both sampler types, and the samples processed immediately to establish the types and quantities of marine organisms that were present. Species identification is expected to be complete by late August.

Jan 1, 1994

By William J. Scott

In the last two years, C-CORE has developed a new seabed sampler directed specifically at obtaining samples from hard or compacted bottoms such as are typical of marine placer deposits. Samples are required for appraisal of concentrations of saleable commodities, and for determination of levels of biological indicators in the deposits. Recently C-CORE and the University of Victoria have been comparing the performance of the Scott/C-CORE sampler with that of the Van Veen sampler often used for biological sampling. Initial trials of the Scott/C-CORE sampler in 1992 at the WestGold mining site, Nome, Alaska, were described by Jewitt et al. at the 1993 UMI. Since that time the sampler has been modified to prevent overfilling, and to limit turbulent flow of water across the top of the sampler buckets when the sampler is recovered with partly-open buckets. The modifications included shoes to prevent sampler overfill, and flexible rubber shielding over top and sides of the sampler to prevent water circulation. Samples have been taken with both samplers in two field areas, one at Pine Cove, Baie Verte, Newfoundland, and the other near Long Pond in Conception Bay on the Avalon Peninsula, Newfoundland. In each area multiple samples were taken with both sampler types, and the samples processed immediately to establish the types and quantities of marine organisms that were present. Species identification is expected to be complete by late August.

Jan 1, 1994

By Hunsoo Choi

Internal textures of manganese nodules from Clarion-Clipperton zone of northeastern Pacific Ocean are classified into five textural zones: columnar-textured layered zone, cuspate-textured layered zone, cuspate-textured massive zone, cuspate-textured porous zone and massive- textured massive zone. Vernadite is the main constituent mineral in the columnar- and cuspate-textured layered zone. Buserite sometimes occurs in the cuspate-textured layered zone. The cuspate-textured massive zone is mainly composed of buserite. Todorokite is also associated with buserite in the massive-textured porous zone, where cuspates and globes are partially replaced by massive texture. In the massive-textured massive zone, todorokite, buserite and birnessite occur together. The analyzed elements of all zones are also classified into four elemental groups by the cluster analysis of correlation coefficients: Mn group, Cu-Ni-Mg group, Fe group and Si group. Mn group consists of Mn and K. Cu-Ni-Mg group consists of Cu, Ni, Zn, Mg and/or Ca, Na. Fe group consists of Fe, Co, Ti and/or Ca, P. Si group consists of Si and Al. Each textural zone is composed of three or four elemental groups. These four elemental groups are correlated with mineral composition, such as, Mn group with todorokite, Cu-Ni-Mg group with buserite, Fe group with Co-bearing iron-oxyhydroxide minerals, and Si group with silicates.

Jan 1, 2002

By John W. Padan

What is known about manganese nodules and their potential commercial recovery is outlined in terms of economics, legal rights, environmental impacts, and mineral genesis. As a result of 20 years of accomplishments it is clear that nodules comprise a real resource, and that they can be collected in water depths up to 5000 m, for brief periods, and raised to a surface vessel at rates of production appropriate for scale model systems. Based upon information in the public domain at present there is more confidence in the nature and magnitude of the resource than in the ability to recover nodules commercially. A review of the literature suggests that the metallurgical processing of manganese nodules is technically feasible and that the associated costs are well predictable. What is less clear is the market outlook for the products. All "overlapping claim" conflicts have been resolved. Therefore, parties with a historic interest in nodule mining appear now to have the right to mine in the future, assuming they properly complete whatever exploration license obligations they may have.

Jan 1, 1989

By Colin Devey

As marine research scientists we especially appreciate the uniqueness and complexity of the deep-sea hydrothermal vent fauna and environments, and are particularly interested in preserving vents for their scientific, aesthetic, ecological, and potential economic values. In fact, because of the specialized nature of the equipment required to work at deep-sea hydrothermal vents, such as occupied and unoccupied research submersibles, scientists are the primary group of people who have the opportunity to visit these extraordinary environments. The potential for significant impact of scientific activities on a single vent site or a population of vent animals pales in comparison to the potential for disturbance by volcanic/tectonic events or industrial mining/harvesting activities. Nonetheless, we recognize that some scientific activities could adversely affect individual sites or impact communities more than is necessary, if research activities are not carefully planned and executed. In addition, because only a limited number of sites are currently known and scientists from a wide variety of disciplines frequently work at single locations, we recognize the potential for use conflicts among scientists, at sites where scientific activity is intense.

Aug 24, 2006

By Peter E. Halbach, Andreas Jahn

Co-rich hydrogenetic ferromanganese crusts are typical marine interface products of growth processes taking place on sediment-free substrate rocks on the seafloor. They grow very slowly and preferentially in water depths below the oxygen-minimum zone (OMZ) and have so far been found even in water depths of up to more than 5000 m, i.e. also below the calcite compensation depth (CCD); these deep ferromanganese crusts are particularly rich in Fe. It is assumed that the O2-minimum zone is the most important source layer of dissolved manganese, the decomposition of fecal pellets here also contributes to this Mn-budget. The process of hydrogenetic precipitation is basically an inorganic colloidal-chemical as well as a surface-chemical mechanism. Microbial mediations can be assumed, in particular since steps of redox-reactions are involved. The two main components of the hydrogenetic substance are hydrated d-MnO2 (vernadite) and x-ray amorphous Fe-oxyhydroxide, both of which are intimately intergrown with each other forming the extremely fine-grained hydrous oxidic material. In seawater, elements occur as dissolved hydrated ions or as inorganic as well as organic complexes which, in general, have either a positive or a negative surface charge depending on the pH of the respective marine environment. These complexes form hydrated colloids that interact with each other or with other dissolved hydrous metal ions. The main agent to oxidize the dissolved Mn2+ ions is oxygen, transported upwards from deeper water by turbulent eddy diffusion and turbulent rise processes at seamount slopes.

Jan 1, 2017

By Demoor Damien

"The exploitation of marine resources has enjoyed renewed interest with a completely new sector, that of the Deep Sea Mining of mineral resources in the seabed, that is now gaining momentum. Nevertheless, the significant environmental constraints represent a challenge for initiating these new activities, whether this is in terms of the knowledge of the concerned ecosystems or in terms of monitoring and minimizing the impact of these new activities. This paper presents 2 technologies that aim to respond to the expectations of the stakeholders in this area. The first consists of the real-time monitoring of installations/operations and their impact on the environment using the most modern underwater technologies and especially long-term deployment AUV based on AUV docking station solution and autonomous long term observatories. The second consists of a membrane allowing the confinement of an area, the reduction of the emission of particles in suspension and noise reduction.IntroductionDeep ocean environments have been explored since the mid-1800s. As the land-based reserves of hydrocarbons and minerals become depleted, increasing numbers of resourcebased projects are being proposed for shallow then deepwater environments. Two distinct resource sectors have recognized the potential commercial value of working in shallow and deepwater environments – Oil and Gas and now Mining."

Jan 1, 2017

By Charles L. Morgan

For the past twenty years or so the oceans of the world have been transformed in the minds of most Americans from the ultimate and nearly infinite receptacles for sewage and other wastes to an almost sacrosanct and threatened last refuge of Mother Nature from man on Earth. While this general movement has helped somewhat to moderate the flows of pollutants into the oceans, it has had severe and sometimes devastating impacts upon various attempts to develop seabed mineral resources. Marine mining proposals have been easy targets for attack. In most cases, they have short or no histories and involve prototype or first-generation methods. They commonly lack major financial backing, and do not command significant public support. Their constituents are limited. Opposition movements to such proposals have been able to evoke strong support by appealing to this "last refuge" image and depicting mining operations as the final assault. In mounting these public appeals, the movements obtain visibility and support. Because of the small and sometimes tentative status of the constituencies which support particular proposal s, the potential liabilities for opposition movements are minimal.

Jan 1, 1989

By G. Cherkashov

A new hydrothermal field with massive sulfide deposits was discovered in 2004 at 16º 38.4?N, 46º 28.5?W on the Mid-Atlantic Ridge. Hydrothermal signals had already been recorded from bottom waters and sediments in this area during cruise 19 of R/V Professor Logatchev in 2000. This site was revisited during the 24th cruise of R/V Professor Logatchev in February 2004 when samples of massive sulfides were recovered and video records of the deposits made. The basalt hosted hydrothermal field is situated at a depth of 3700-3750 m, 600 m above the inner floor on the eastern slope of the rift valley. Structurally, the new field is located at the intersection of a deep along-axis marginal fault and a transverse sub-latitudinal dislocation. Six sulfide mounds as well as associated metalliferous sediments were mapped (sampled and/or recorded by video profiling) within the hydrothermal site. The largest ore body, 500 x 225 m, in the southern part of the field consists of small blocky talus and relics of sulfide chimneys partly covered by iron oxyhydroxides. The chimneys are 1-5 m high. The southern and western boundaries of the massive sulfide deposit have not yet been delineated. More than 1,100 kg of massive sulfides and stockwork mineralization were sampled at 7 sites by dredge and TV-grab. Everywhere, iron sulfides were the principal minerals present. Pyrite in association with lesser amounts of chalcopyrite occurs in both massive sulfides and stockwork mineralization. Of particular interest is the chalcopyrite-siliceous stockwork where silicified and chalcopyritized basalts are intruded by a network of chalcopyrite veinlets. These zones could be fairly thick and enriched in base metals. Sphalerite was very rare.

Jan 1, 2004

By Paul C. Rusanowski

Mining is a waste intensive industry, oftentimes producing hundreds of kilograms of waste rock and tailings for every gram of metal recovered. Disposal of mine tailings is a major concern in most mining operations. In Southeast Alaska the steep terrain and high seismic hazard province limits cost effective opportunities for land disposal of tailings. The lack of infrastructure and long travel distances generally limits secondary utilization of tailings, as well. Since the mines are located close to tidewater, submarine tailings disposal is an attractive option for tailings management. At the present time the EPA will not issue a permit that authorized marine tailings disposal from any mining process that includes flotation technology. Upland disposal is the "Best available technology" and must be used. Consideration of submarine disposal is generally precluded because the tailings are contaminated with fluids from the flotation process. However, when developing technological solutions to minimize environmental disturbance, destruction, pollution, and risk, submarine tailings disposal deserves another evaluation. In Southeast Alaska it may be the "Best available technology" based on an assessment of all issues and concerns in these mining projects.

Jan 1, 1991

By Delphine Pierre, Jean-Marie Augustin, Anne-Sophie Alix, Charline Guérin, Cecile Cathalot, Yves Fouquet, Arnaud Gaillot, Ewan Pelleter, Carla Scalabrin, Florian Besson

With the world’s growing demand for metals, seafloor massive sulfides (SMS) deposits are now seen as a possible mineral resource that could contributes to secure metal supply for human needs. SMS deposits are characterized by high concentrations of base metals and at some place high contents of precious and rare metals. Since 1977 and the discovery of the first high temperature (HT) hydrothermal vent and its sulfide mineralization and high biodiversity, more than 300 sites are known today. If the exploration strategy for detection of active hydrothermal sites is now robust, their associated mineralization will not (and must not) constitute a potential target for deep-sea mining due to environmental concerns and technical limitations. Recent studies on SMS deposits are rather focused on extinct and buried mineralized sites characterized by a lower biomass. Several geophysical techniques to explore and detect extinct SMS (eSMS) and buried SMS (bSMS) have been developed (e.g. Kawada and Kasaya, 2017; Szitkar et al., 2017, 2014) using different approaches (e.g. regional or local scale; ship-based or using underwater vehicles) with several degrees of success or limitation. Here we present results from acoustic surveys performed on the TAG hydrothermal district during the BICOSE (2014) and LEVE-SMF (2016) cruises and direct observation provided by HOV (Nautile) dives carried out during HERMINE cruise (2017). Acoustic data were acquired using two different multibeam echosounders (MBES): the hull-mounted Kongsberg EM122 (12 kHz, R/V L’Atalante) and the ROV-mounted RESON SeaBat 7125 (400 kHz, ROV Victor) (Figure 1). After processing, acoustic seafloor backscatter data from both MBES provides complementary qualitative results in relation to the seafloor composition. The analysis of the seafloor backscatter data obtained by near-seafloor surveys with the high-resolution 400 kHz MBES shows a clear relationship between low backscatter strength values and areas covered with pelagic and hydrothermal sediments whereas high backscatter strength values are associated to pillow lavas and basaltic scree. Intermediate backscatter strength values are rather related to old and younger eSMS as well as to mineralization on TAG active mound.

Jan 1, 2018

By Raymond A. Binns

In this first sub-seafloor examination of an active hydrothermal system hosted by felsic volcanic rocks at a convergent plate margin, we drilled 13 holes altogether, achieving deep cored penetrations at two sites. Our aims were (1) to delineate the lateral and vertical variability in mineralisation and alteration patterns below the PACMANUS hydrothermal site near the 1650-1700 m-deep crest of Pual Ridge in the eastern Manus back-arc basin, so as to understand links between volcanological, structural and hydrothermal phenomena, and (2) to establish the nature and extent of microbial activity within the system. Technological innovations vital to success included our precise location of holes on small targets with drill-stem video, the use of a new hard-rock re-entry strategy, and deployment of casing with a new hammer drill. Other technical achievements were the first ODP application of an advanced diamond coring system, and the first direct comparison in a hardrock environment between structural images obtained by wireline methods and by logging-while-drilling (resistivity-at-bit).

Jan 1, 2002