Search Documents

By Michael J. Brown

Load testing is important for controlling the quality of piled foundations. The Statnamic test is an alternative to existing testing methods with a load duration that lies between that for static and dynamic tests. Current methods of analysis offer excellent correlation between static and Statnamic tests for coarse-grained soils but often over-predict the capacity for fine-grained soils. Thus a calibration chamber is being used to produce instrumented beds of clay with reproducible properties. A model pile placed in the beds can be loaded at varying rates using a computer controlled servo-hydraulic system. Results from the modelling will be used to improve methods of analysis and govern the design of a full-scale study. Initial results suggest the rate effect can be represented by a power law relating pile velocity and resistance. Statnamic loading of the model pile produced large negative pore pressures in the clay bed.

Jan 1, 2002

By Wesley Schmutzler

The Deep Mixing Method (DMM) was employed to raise and support the LPV (Lake Pontchartrain and Vicinity) -111 Levee in New Orleans. Even using innovative technologies, the tight schedule to achieve the 100 year elevation by June 1, 2011 was a daunting endeavor. The size and scope of DMM proposed for LPV-111 was on a scale never attempted outside of Japan. Over 1.65 million cubic yards of DMM was installed. LPV-111 is adjacent to the Bayou Sauvage Wildlife Refuge, which is the largest urban National Wildlife refuge in the United States. By utilizing DMM to control settlement and improve stability of the taller levee, side slopes were steepened from the conventional 1V:4H to 1V:2.85H, thus avoiding encroachment into the Bayou Sauvage and reducing the amount of clay needed for the completed levee. The COE utilized Early Contractor Involvement (ECI) for this contract. The ECI process allowed for input from the DMM contractor, TREVIICOS South, in order to optimize equipment resources and material requirements. This paper gives an overview of the extensive DMM requirements for LPV-111 and explains the benefits of the ECI process.

By Hiren J. Shah

The urban environment and geology create unique challenges for design and construction of deep foundations. The effect of these is prominently experienced in New York City. Three such project case histories are presented in this paper. The first project is a multi-use development. Relatively unusual glacial geology was observed at the site during the subsurface investigation phase. This played an important role in the selection of deep foundations as well as during construction. The design and construction aspects of the pile foundations, settlement estimates, a pile drive test program during design, piling equipment and production pile installation are discussed herein. A relatively smaller project is the second case history. A combination of drilled and driven deep foundations was employed in one area of the project due to its unique conditions. In another area of the project, an addition to a structure required the use of supplemental foundations to resist new additional loading. Tight space and load sharing with the existing foundations were important considerations in the design and construction. Finite element modeling of the existing and completed structure was performed which was an interesting aspect of the project. The third project case history involves a very large multi-billion dollar project in which various different types of deep foundation elements were used. The aspects requiring the use of such a variety of types and sizes of deep foundation elements included: geologic conditions, re-use of existing foundations, protection of adjacent infrastructure, construction staging, restricted space, loads, deep excavations, cost and schedule.

Jan 1, 2011

By Karl A. Higgins

In 1976, Prof. G. G. Meyerhof published a famous article in the Journal of Geotechnical Engineering titled ?Bearing Capacity and Settlement of Pile Foundations?. This article presents the authors opinions on calculating pile capacities in clays and sands, group capacities and pile settlement. A portion of the article presents correlations of shaft friction and end bearing to the Standard Penetration Test (SPT) N-value. Subsurface exploration via the Standard Penetration Test is the most widely used exploration tool in the United States, so correlations of pile capacity to N-value are significant to the practice of geotechnical engineering. Meyerhof?s SPT-N correlations are relatively simple calculations compared to other pile capacity computation methods presented in the article or found in other text books (such as the a-method, b-method, Nordlund, Vesic, Meyerhof?s semi-empirical, others) and therefore are popular amongst practicing geotechnical engineers. At the time these correlations were published by Prof. Meyerhof, utilization of dynamic testing with the Pile Driving Analyzer (PDA) was not widespread in geotechnical engineering practice. Prof. Meyerhof?s correlations appear to be based upon conventional static pile load testing of instrumented piles. Dynamic pile measurements to estimate a pile?s static capacity provides certain advantages over conventional static load testing, namely the determination of unit shaft friction values at discrete intervals along the pile, and the unit end bearing support value. The author has compiled a database of driven, displacement piles tested with dynamic methods (ref. ASTM D4945, Test Method for High-Strain Dynamic Testing of Piles). The data was collected between 2002-2010 and is comprised of displacement piles driven into coastal plain sediments in the mid-Atlantic states of Virginia, Maryland and the District of Columbia. In layered soils, dynamic testing in particularly helpful as it reveals the differences in unit shaft friction for varying soil types. One hundred ninety (190) piles are included in the database, with a corresponding 1,373 discrete shaft friction and 190 end (toe) bearing measurements. The pile type typically consisted of 12 and 14 inch square, prestressed, precast concrete piles; however, a significant number of piles were steel HP 12 or 14 inch sections. The database was sorted based upon soil type, and then correlations of shaft friction and end bearing were derived in the same or similar manner as Meyerhof?s original 1976 publication. The new correlations are compared to Meyerhof?s original values.

Jan 1, 2011

By Y. Duraisamy

This paper presents the compressibility of tropical peat reinforced with cylindrical cement column. When a cement column installed vertically in peat, its compressibility was reduced because of the hardened skeleton matrix formed by cement particles bonding with adjacent soil particles in the presence of pore water. The effects of diameter, number of columns and cement proportions in cement columns on the compressibility have been investigated in this study. The results indicated that compressibility index Cc and Ca decreased with the increase in diameter of the cement column. Specimens with 45 mm and 60 mm diameter of cement column were cured for 28 days, after which they were subjected to Rowe Cell Consolidation test. Based on the results obtained, it shows that cement columns can successfully reduce the compressibility of tropical peat.

Jan 1, 2007

By Edwin W. Meyer

The augered cast-in-place piling technique was used to install deep foundations 20 feet into weathered sandstone. The project involved the upgrading of the Air Quality Control System (AQCS) for a 560 megawatt coal fired power plant located in Stillwater, Minnesota. The site subsurface consisted of 20 feet of overburden overlying weak sandstone. The overburden consisted of sands and gravels with cobbles and boulders, and variable thicknesses of peat. Ground-water at the site was approximately 8 feet deep. Two foot diameter piers were selected to facilitate installation through the cobbles and boulders in the over-burden and to penetrate the sandstone 22 feet. During installation of the first pier, the weak sandstone broke down to sand-sized material that could not be cleaned from the pier hole without the use of slurry to hold the material in suspension. However, the use of slurry would significantly impact both schedule and cost. Since the sandstone could be easily drilled with the pier equipment, it was believed that 2 foot diameter deep foundations could be installed as designed using augered cast-in-place piling techniques. A brief test drilling pro-gram was conducted to evaluate the viability of 2 foot diameter continuous flight augers penetrating 22 feet into the weak sandstone. The test drilling indicated that augered cast-in-place installation techniques should be successful. Following a short delay to mobilize the additional required equipment, construction commenced. Installation of the 2 foot diameter augered cast-in-place piling to a depth of 22 feet into the weak sandstone was successfully performed.

Jan 1, 2006

By Dan Brown

A method is outlined for computing the contribution of a micropile group to global stability of a sliding mass. The forces in the micropile are computed in a way which accounts for the effect of soil mass movement on the mobilization of axial and shear forces and which maintains compatibility between shear and axial force as a function of displacement. The method provides a rigorous model to incorporate the pile forces into the stability calculations, including the effect of pile forces on the resultant shear and normal forces at the sliding surface. This paper demonstrates the proposed solution using a simple example slope.

Jan 1, 2007

By Melvin I. Esrig

Lime Cement column stabilization of soft clay and sand in Salt Lake City, Utah and in San Francisco California is described and discussed. Stabilization permitted the construction, in a single stage, of a 14 m MSE wall on "medium" clay in Salt Lake City. It was used to mitigate the potential for liquefaction in San Francisco and to stabilize the Young Bay Mud beneath the BART extension to San Francisco Airport. These applications are described and the field measurements of performance are reported.

Jan 1, 2000

By J. Osterberg

A new device has been developed for load testing driven piles and drilled shafts which consists of an hydraulic jack or bellows which has a telltale rod fastended to the bottom. The rod extends upward to the surface through a pressure pipe. When pressure is applied, the jack or bellows expands, applying an equal upward and downward load at the bottom. The downward movement at the bottom is indicated by the rod and the upward movement is indicated by the movement at the top. Thus, upward and downward load-deflection curves can be drawn. As load increases, failure will occur either in end bearing or friction. Results of field installations are described. Total loads of up to 1,100 tons metric have been used. The method obviates the need for the reaction load required for the conventional pile loading test and separates friction and end bearing. It is especially advantageous for use over water, in crowded spaces and for inclined piles.

Jan 1, 1989

By Stan Merjan

Composite piles with precast concrete tapered pile tips (TPT Composite Piles - U.S. and foreign patents) are a new and important addition to the piling types available to the construction industry. TPT Piles were invented by Stanley Merjan, Vice President of Underpinning & Foundation Constructors, Inc.. U. F. C. installs these piles in the Northeast United States and licenses piling contractors in other parts of the country. TPT Piles have been developed for use in sandy subsoils at depths to 70 feet or greater. The TPT system (see Figure 1) is simple. A pile stem of conventional material (shell, pipe, steel, wood, precast concrete) is connected to a socket formed in a precast concrete tapered pile tip (TPT). This composite assembly is then driven as a unit by ordinary pile driving methods until adequate driving resistance (established by formula or load tests) is met in a suitable soil strata. This driving resistance develops from the displacement and densification produced by the TPT. Many combinations of tip shapes and stems are available to suit particular job requirements with respect to subsoil conditions and pile capacities. TPT Piles should be considered for use on a wide variety of jobs. The advantages offered by a TPT installation include: ? High capacity piles in marginal soils ? Minimal lengths required to produce these capacities ? The use of conventional pile driving equipment and procedures ? Pile inspection techniques that are the same as for ordinary pile driving Furthermore, TPT piles are economical due to a combination of a low cost per ton of pile capacity and high productivity, both of which lead to significant savings in foundation costs and time required to complete foundation work.

Jan 1, 1987

By Eric R. Borys, Amaneh E. Kenarsari, Brett Gitskin

This case study discusses impacts of excessive Earth Retention System (ERS) lateral movement at a project in city of Chicago. The ERS (cantilevered sheeting) moved inward towards the excavation and caused lateral displacement and cracks in six drilled shafts located about 1 to 2 lateral feet (0.3 to 0.6 m) from the face of the sheet pile wall. Up to 9 inches (23 cm) of horizontal movement was observed on top of the supporting sheet-pile. Similarly, survey measurements showed the top of the drilled shafts moved laterally up to 8 inches (20.3 cm). To evaluate the cause of failure and determine a remediation solution, the soil, shaft and site conditions were investigated. Pile Integrity Tests (PIT) were conducted at the affected drilled shafts. The shafts with identified anomalies were cored and video-recorded. The cause of the failure was determined to be related to variable soil conditions across the site, deeper excavation (i.e., increased effective ERS wall height), and other differences between design and as-built conditions. Internal bracing, in the form of walers and rakers, was installed to limit further movement of the sheet pile as a short-term solution, with additional grade beams framed into the basement slab-on-grade as a long- term solution. Five of the six cracked shafts were spliced with reinforcing bars and high strength grout and one shaft was replaced. INTRODUCTION The subsoil in the Chicago Area mostly consists of glacial till clays underlain by water-bearing granular soil over bedrock. The glacial clays have very soft to medium consistencies for a typical thickness of 30 to 50 feet (9.1 to 15.2 m) below which hard clays (Hardpan, i.e., heavily over-consolidated clay soils) are encountered. The soft clays are often referred to as the “Chicago Blue Clay”. Beach Sands are also found above upper soft clays in several areas, especially within a three-mile strip near Lake Michigan (Peck and Reed 1954). Due to the existence of soft clay in Chicago area, supporting the mid to high rise buildings on drilled shafts extended to Hardpan is a common practice in modern building design. In the early 19th century it used to take about 3 weeks to excavate 1 shaft hole and about 1½ days to fill the shaft with concrete in Chicago (Manierre 1916). The early 19th century methodology of excavating a shaft consisted of hand digging the shaft, installing wood lagging as temporary shoring with spoils removed with a rope and pulley system from the surface. Today, the excavation of a typical drilled shaft in Chicago uses heavy drilling equipment and requires much less time for excavation and concrete placement. It is not uncommon for contractors to excavate shafts and place concrete at a rate of about 2 to 5 drilled shafts per day (with one drill rig).

Jan 1, 2018

By R. H. Wright

This paper describes the design philosophy and methods employed in constructing the foundation elements for the Little Britain Project in the City of London. The Contract is a design and construct package for the foundations of a 3-storey basement which will be built using "top-down" construction techniques and is to be carried out by Fairclough Piling and Marine on behalf of Wimgrove Nominees. The Project includes 8000 sq.m. of diaphragm wall and barrettes 139 No. large diameter piles ranging from 900mm to 3000mm in diameter and up to 45m deep, and 9 No. cruciform barrettes for the heaviest column loads. Major factors influencing the design of these foundations include differential settlement, heave analysis and a fast track construction approach. Little Britain will provide 43000 sq.m. of space in two linked buildings which will bridge a new road joining London Wall to Newgate Street. The foundation contract is well advanced and the building is due for completion in the Summer of 1990.

Jan 1, 1989

By Hal W. Hunt

Heavier loading and more efficient equipment is helping to keep driven piles competitive in America. Better Knowledge and testing of soils and support materials make it practical to use higher stresses; this is being strongly promoted by those directly concerned with timber, steel and concrete piles. Readily available point protection is increasingly used to assure penetration of piles without damage to full load bearing capability. Fabric drains are being installed with pile equipment to speed consolidation of soils. Sheet pile configuration has changed; production has been reduced largely because of imports. Dynamic checking of representative piles for load carrying capability is replacing conventional load testing of just a pile or two ? at much lower cost.

Jan 1, 1987

By John W. M. Lambert

This paper describes the execution and the results of a new method to seal off leaks in water retaining constructions. The new method, called BioSealing is based on activating the bacteries, present in soil and groundwater. The method was tested under field conditions in 2004 and applied at the HSL aqueduct of the 'Ringvaart Haarlemmermeer' in 2005.

Jan 1, 2006

By Zhang Jiaju

For the highrise buildings with deep foundstion of irregular plane shape, an appropriate calculate model to the heave of foundation soil after excavation is proposed and studied using analytic method and FEM (Finite Element Method) respectively to provide an effective way for solving this kind engineering problem. Also combined with the practice of construction deep foundation of Capital Mansion, calculation of the heave of foundation soil after excavation is given. Compared these results from above two methods with the results measured in situ, it is conformal on the whole, and the results by FEM are much closer with the measured.

Jan 1, 1991

By Brian H. Greene

The U.S. Army Corps of Engineers, Pittsburgh District, is in the final phases of modernizing the locks and dams on the Monongahela River. One facet of this modernization is to replace the existing Locks 4 located on the Monongahela River approximately 40 river miles upstream from Pittsburgh, Pennsylvania. The existing locks consist of a 56-foot x 720-foot main chamber and a riverside 56-foot x 360-foot auxiliary chamber built in the 1930s. Two new lock chambers, each 84-foot wide by 720-foot long, will be constructed at the location of existing Locks 4 and will be named Charleroi Locks. The purpose of the new project is to facilitate navigation on the lower Monongahela River. Pittsburgh is currently the second largest inland waterway port in the nation, and the new locks will be an important component of the navigational infrastructure. The existing lock walls are of mass concrete construction and are founded on wooden timber piles driven to rock through alluvial sands and gravels. The new lock walls were designed to be supported by approximately 300 reinforced concrete drilled shafts, varying in diameter from 4 to 6 feet. To handle axial loads, the drilled shafts were designed for end bearing, with some skin friction. The tips of the shafts will be founded within competent rock. Since the walls will undergo lateral loads, the drilled shaft design also had to consider this loading condition. Some of the drilled shafts will be installed within coffer boxes, which will incorporate a tremie concrete seal down to top of rock. Complicating the design even further was the fact that some portions of the new walls will be supported by shafts that extend some 9 feet above top of rock through alluvial soils, producing a cantilever effect. The first phase of the new lock construction was initiated in the summer of 2005 with a contract awarded to replace the river wall. This required shutting down the existing riverside lock chamber and diverting all river traffic to the longer existing land chamber. The foundation of the new river wall will use 144 drilled shafts. To optimize the design embedment of drilled shafts in rock for the river wall, an exploratory drilling program was conducted by the contractor in July and August, 2005. Based on the quality of the sedimentary bedrock, the shafts will be embedded in rock from 31 to 38 feet. To achieve adequate end bearing resistance, the tips of each shaft will extend through predominantly claystones into a more competent siltstone unit for a minimum embedment of one foot. The contractor also performed an exploratory pile driving program to aid in the construction of the drilled shaft casing and the cut off walls that will encapsulate the river wall. Two demonstration drilled shafts located outside the footprint of the new river wall, will be constructed prior to the drilling of any production shafts. The demonstration drilled shafts will verify that the contractor is able to meet the design criteria and quality requirements of the contract. The river wall contract is currently underway and is scheduled to be completed in 2010.

Jan 1, 2006

By Donald A. Bruce

Pin Piles are small diameter, bored, cast-in-place piles used to underpin structures. They were first employed over 40 years ago in Italy, and have been used in the U.S. since the late 1970's. However, it is only in the last few years that their full potential in terms of load holding capacity has been exploited: whereas 100 kip working loads typified former practice, ultimate loads approaching 700 kips have recently been recorded for Pin Piles founded in sand. In order to better understand the actual performance of these piles, fundamental research has been conducted by a consortium of industry and academia. This paper describes the advances made in the laboratory and full scale field testing programs. In particular, the extensive field tests have been conducted in a variety of materials in which different pile configurations have been cyclically tested to failure. By using this test method, the elastic performance of the piles has been examined and so the progressive interfacial debonding phenomenon has been studied. This has led to the development of the Elastic Ratio concept which is proving extremely useful in analyzing and predicting Pin Pile performance. Data are provided from the full scale Test Pile Programs conducted at Mobile, AL and Port Vancouver, WA. Given that Pin Piles are usually installed in areas of low headroom or restricted access, and through difficult, occasionally contaminated soils, the paper also describes key aspects of construction.

Jan 1, 1993

By Allan Sylvester

Construction of the Shot Tower Metro Station in Baltimore, Maryland was performed in two phases. In the first phase, a contractor was retained to excavate the station in order to construct twin tunnels from the Shot Tower Station to the John Hopkins Station. The retention system for this 70' deep excavation consisted of a Soldier Pile in Tremie Concrete (SPTC) wall supported by cross-lot bracing. In phase two, The Clark Construction Group, Inc. was retained to construct the station interior structure, two entrances, two station ancillary shaft structures and the track work for the station and tunnel. The excavation for the construction of the two entrances adjacent to the 70' deep station SPTC wall had to proceed prior to completion of the station structure due to the tight construction schedule. A system of overlapping secant piles was specified as a vertical support of excavation element for the West Entrance. The secant piles would have provided a watertight, rigid support to resist the load from the SPTC wall constructed in phase one. A watertight system was required in order to minimize the settlement of adjacent buildings supported on wood piles. Clark Construction was concerned with the constructability, cost and performance of the specified secant piles and looked for other innovative methods of providing a watertight and rigid system. Substitution of a reinforced slurry wall in lieu of the secant piles was cost prohibitive due to the additional cost of concrete placed under tremie. Clark, being familiar with cement-bentonite cut-off walls and slurry wall construction procedures, proposed the construction of a PSHG wall, in lieu of the secant piles. The PSHG wall construction consisted of trenching 30" wide by 20' long by 60' deep panels under a self-hardening slurry. Once the excavation for a panel was completed, a 60' deep prefabricated soldier beam and lagging panel was placed in the slurry. The slurry design mix then self-hardened within the cure time, allowing excavation for the structure to proceed This paper will discuss the design, details and construction methods used on the PSHG wall and will compare the advantages of the PSHG system to conventional support systems.

Jan 1, 1997

By Ashutosh S. Dhar

Cast-in-place piles were examined in this paper from the viewpoints of construction quality, axial capacity, and load-displacement responses. The results of ten 450 mm diameter (18? f) bored piles, installed in a soil deposit of silt to medium dense sand using the method of percussion drilling, were tested under static loads. The results of the pile load tests were used for evaluation of various design methods of calculating pile capacity. The study revealed that the design methods based on the concept of critical depth underestimated the ultimate skin fiction. Thus, the applicability of the critical depth concept for design of bored piles under the soil condition considered may be unreliable. The estimated skin friction factor, ß, was too low in these methods. The Tomlinson method and the Neely method provided the best prediction of the ultimate skin friction. The methods used for calculating end bearing resistance were found to provide a conservative estimate of the resistance. During pile load tests, a settlement of 5 to 6 mm was required for full mobilization of skin friction for the piles in loose sand, while larger settlements (> 10 mm) were required for piles in denser soil. The ultimate skin frictional resistance was observed to be low for piles in loose sand.

Jan 1, 2006

By Ron Bromenschenkel

The State of California, Department of Transportation is currently retrofitting a major interchange near the San Francisco area. The project is located in a highly traveled area of Oakland with light rail commuter service near many footings. Over 600 micropiles are being used in conjunction with CIDH piles for footing stabilization. A specially designed Soil Nail pile will support footings for a new light rail utility structure. Pile testing features in this contract serve as points of interest for future foundation designs. The presentation focuses on substructure issues of this incterchange retrofit. Both design and construction considerations will be covered. Design Considerations: ? Project Description ? Structure inadequacies ? Design criteria ? Design contraints ? Retrofit strategy ? Consultant analysis ? Pile Designs and Test Sites ? Contract Specifications ? Construction Plan and Cost

Jan 1, 1998