Search Documents

By Hiren J. Shah

Across much of New York City, the geology of glacially deposited soils follows a common sequence. Outwash sands generally overlie varved silts and clays, which lie above a basal till deposit underlain by the bedrock. Pile foundations at projects with such typical stratigraphy generally develop their axial capacities by extending below the fine-grained deposits into the till or the bedrock. Contrastingly, at a project site on the Brooklyn waterfront, high capacity piles were efficiently and economically installed by driving them into the relatively shallow glacial drift and till deposits which lay above thick fine-grained compressible glacial lake deposits. An unusual aspect about the foundation design at the Brooklyn project site is that, relatively short and high capacity piles were driven into the shallow glacial drift and till deposits, overlying the thick fine-grained glacial lake deposits. In order for this unusual foundation scheme to be feasible and economical, the piles needed to achieve their driving criteria in the upper strata. Consolidation settlements in the lower stiff and over-consolidated glacial lake deposits below the pile tips had to be relatively small. The paper discusses the unusual stratigraphy in this area of Brooklyn in greater detail with geologic profiles and engineering characteristics of the glacial strata. It also discusses the design aspects of the pile foundations, settlement estimates, a pile drive test program during design, results of the static load test program during construction, and production pile installation results.

Jan 1, 2008

By Abid Adekunte

"In recent years, developers have had to deal with complexities associated with numerous cases of deep basement construction in built-up areas. Design and construction of deep excavation support systems in urbanised zones come with many technical challenges. Restricted working spaces often render the use of temporary struts as wall restraint systems unpopular, as working space needs to be maximised. Also, tie-back anchors are often inapplicable due to the existence of adjacent structures. Therefore, developing alternative restraint systems for deep basement structures in builtup areas is becoming increasingly important to the present day basement engineer.This paper is centred on the design, construction and monitoring of enabling works for deep basement structures on three sites in the United Kingdom and Republic of Ireland. Traditional tieback anchorage and propping systems were inapplicable on the sites. As alternatives, separate novel wall restraint systems were developed and adopted, to enable excavation on each of the three sites.Performances of the novel wall restraint systems, as well as the responses of adjacent structures were monitored. Numerical modelling and field monitoring results show the three alternative wall restraint systems to be safe and effective. The paper also highlights the advantages of the novel solutions over conventional methods.INTRODUCTIONRecently, deep basement structures have become popular components of urban building developments. As pointed out by Pearlman et al., 2004, this could be attributed to the inadequacy of surface parking spaces in urbanised zones, while underground parking facilities are also believed to improve both aesthetic and commercial qualities of urban structures.However, while the incorporation of basement structure into new urban development appeals to developers and architects, the engineering design and construction aspects of basement works typically come against a whole lot of complexities and challenges. As highlighted by Wong, 2002, engineering problems associated with basement construction in built-up areas are numerous, some of these include; complicated sub-soil conditions, dealing with excessive active pressures, complex temporary works, proximity of sensitive adjacent structures, high level hazards to construction workmen and surrounding community, inadequate working space, etc."

Jan 1, 2015

By Tae Hwan Lee, Jun-Shin Lee, Daejin Kwag, Sangchul Bang, Gerard T. Houlahan, Moo Sung Ryu

"Geotechnical engineers have been installing innovative, permanent underwater foundation systems utilizing suction buckets for the offshore industry since the early 1980s (Senpere and Auvergne, 1982). This foundation system has been successfully used on numerous and various types of offshore structures in a wide range of environments. Suction buckets have numerous advantages compared to conventional underwater foundation systems. The more notable advantages include easy installation, large loading capacity, low noise and retrievability. The application of reduced water pressure inside the bucket facilitates the installation of the suction buckets, where a suction pump attached at the top of the bucket can accomplish the entire driving operation. Because of this efficient operation, very large suction buckets can be driven into the seafloor, which eliminates the use of a large number of small piles.In Korea, one of the most economical and reliable renewable energy sources is wind power; however, onshore wind power generation has encountered many problems, such as the lack of favorable sites and public concerns about noise and environmental damage. Consequently, offshore wind power generation has attracted increasing attention due to its abundant potential, high efficiency of grid connection, and availability of easy expansion.In November 2011, the government of Korea announced a national offshore wind power development roadmap, which targeted its offshore wind power generation with the goal of becoming one of the top three nations in the world for offshore wind power generation. Korea Electric Power Corporation Research Institute (KEPRI) is the main research arm of the Korea Electric Power Corporation (KEPCO) and conducts research and development on electricity, power generation, renewable energy and other energy-related matters. KEPRI ultimately provides forefront knowledge and leadership to KEPCO with respect to energy and related areas for its near- and long-term needs. Financial support for the overall project, of which the suction bucket foundation system installed for the pilot phase wind turbine is described below, was provided from the New and Renewable Energy Program of the Korea Institute of Energy Technology Evaluation and Planning funded by the Korean Government Ministry of Trade, Industry and Energy"

Jan 1, 2017

By Tae Hwan Lee, Jun-Shin Lee, Daejin Kwag, Sangchul Bang, Gerard T. Houlahan, Moo Sung Ryu

"Geotechnical engineers have been installing innovative, permanent underwater foundation systems utilizing suction buckets for the offshore industry since the early 1980s (Senpere and Auvergne, 1982). This foundation system has been successfully used on numerous and various types of offshore structures in a wide range of environments. Suction buckets have numerous advantages compared to conventional underwater foundation systems. The more notable advantages include easy installation, large loading capacity, low noise and retrievability. The application of reduced water pressure inside the bucket facilitates the installation of the suction buckets, where a suction pump attached at the top of the bucket can accomplish the entire driving operation. Because of this efficient operation, very large suction buckets can be driven into the seafloor, which eliminates the use of a large number of small piles.In Korea, one of the most economical and reliable renewable energy sources is wind power; however, onshore wind power generation has encountered many problems, such as the lack of favorable sites and public concerns about noise and environmental damage. Consequently, offshore wind power generation has attracted increasing attention due to its abundant potential, high efficiency of grid connection, and availability of easy expansion.In November 2011, the government of Korea announced a national offshore wind power development roadmap, which targeted its offshore wind power generation with the goal of becoming one of the top three nations in the world for offshore wind power generation. Korea Electric Power Corporation Research Institute (KEPRI) is the main research arm of the Korea Electric Power Corporation (KEPCO) and conducts research and development on electricity, power generation, renewable energy and other energy-related matters. KEPRI ultimately provides forefront knowledge and leadership to KEPCO with respect to energy and related areas for its near- and long-term needs. Financial support for the overall project, of which the suction bucket foundation system installed for the pilot phase wind turbine is described below, was provided from the New and Renewable Energy Program of the Korea Institute of Energy Technology Evaluation and Planning funded by the Korean Government Ministry of Trade, Industry and Energy."

Jan 1, 2017

By Andrew Higgins, Jamey Rosen

This presentation will demonstrate some recent advancements in the applications of Project Information Systems (PIMS) technology to seepage barrier walls in the context of evolving Owner Specifications. The use of geospatial technology in particular is used to track, visualize, and analyze data from a variety of sources and serve those data to contractors and owners via dashboards and as-built drawings. Data describing the geometry of construction elements (including diaphragm panels, secant piles, and jet grout columns) is of particular importance on these projects, and this presentation will include case studies in the United States of how these data are used to determine if a barrier wall is constructed as designed and if it meets the owner specifications with respect to tolerance (i.e., if each element is sufficiently close to vertical) and overlap (i.e., do adjacent elements overlap sufficiently to prevent leakage).

May 1, 2022

By Osvaldo Valdez, Matteo Bertoni, Aem Ragy

The East St. Louis Deep Cutoff Wall project is located in the area of East St. Louis, Illinois, across the Mississippi River from the city of St. Louis, Missouri, along the left descending bank of the river. The project is a fundamental part of the U.S. Army Corps of Engineers' (USACE) effort to rehabilitate and secure the aging East St. Louis levee system that provides flood protection to approxi- mately 250,000 residents and more than $4.5 billion in economic value. The project was devised and de- signed by USACE as a cutoff wall to be installed in the Metro East Sanitary District levee segment, one of the levee segments that form the East St. Louis system. The contract for the construc- tion of the cutoff wall was awarded in November 2019 to Bauer Foundation, the American subsidiary of the Bauer Group.

Sep 1, 2023

By Harald P. Ludwig, Matthew J. Niermann

The support of excavation (SOE) for the Capitol Crossing project in Washington, DC consisted of a combination of soldier piles, lagging, tiebacks, braces, underpinning, single auger soil mixed (SASM) walls, micropiles, and a tiedback slurry wall. Over 130,000 square feet of SOE was installed with more than 1,300 tiebacks providing lateral support for excavation depths of up to 72 feet. Several structures including the Holy Rosary Church, the Bell Tower, the Casa Italiana, and a modern office building were supported by a combination of conventional hand dug underpinning pits, bracket piles, and stiff SASM walls. This paper will focus on the design and performance of the SOE adjacent to the Holy Rosary Church and the Bell Tower. Deflection-based design was used to estimate the movements of and limit damage to these structures. An extensive monitoring program was used to provide real time movement data. The results of

By Scott M. Mackiewicz

This project includes replacement of the historic vertical-lift span Meridian Bridge (U.S. Highway 81 over the Missouri River) that connects Yankton, South Dakota with rural Cedar County, Nebraska. The new 76-foot wide, 1,590-foot long steel plate girder structure required the use of drilled shaft foundations that extended into the underlying Carlile Shale formation. Designers indicated that an individual drilled shaft capacity of about 2,000 kips will be needed at each of the river piers, and based on the subsurface information, 8 to 10-foot diameter drilled shafts extending to about 115-foot would be required for support of the bridge structure. An Osterberg Load Test was performed on one test shaft to determine the ultimate skin friction and end bearing of the Carlile Shale. This paper describes the design and installation of the load test drilled shaft as well as presents the load test results as compared with predicted design values determined using FHWA methods.

Jan 1, 2008

By Tsuda Wakaki, Naoki Takahashi, Natsuki Okuno, Hidenori Takahashi, Ikuo Towhata, Yoshiyuki Morikawa

"Deep mixing (DM) method has been increasingly employed as a countermeasure against subsoil liquefaction in recent years. Pile-type DM, however, is considered to have little effect as a liquefaction countermeasure, because the shear deformation of unimproved soil around the piles cannot be reduced. However, experimental results, which imply that shear deformation of unimproved soil around DM piles can be reduced, were reported. Furthermore, a new plane-arrangement of DM piles has been proposed to mitigate lateral flow induced by liquefaction. The DM piles in this arrangement confront the lateral flow in any direction, compared with the piles arranged in conventional pattern such as square and triangular arrangements. In this study, a series of dynamic centrifuge model tests was conducted to verify the lateral flow resistance of DM plies in the new arrangement. The results indicate that the DM plies can reduce the lateral flow of liquefied ground when the pile displacement and the pile head rotation are restricted. In addition, lateral load acting on DM pile from liquefied ground, which is required for design strength of the DM pile, was investigated.INTRODUCTIONDeep mixing (DM) method has been increasingly employed as a countermeasure against subsoil liquefaction in recent years. The solidified body formed by the deep mixing method is usually block or lattice shape, composed of solidified columns that overlap each other horizontally. Lattice-type solidification has been shown to be effective as a liquefaction countermeasure despite the presence of unimproved soil inside the lattice wall, because the shear deformation of the interior soil is restrained by the wall (Suzuki et al., 1989). On the other hand, it has been thought that pile-type DM cannot reduce shear deformation of unimproved soil around the piles, because the displacement of the pile is less restricted than that of the lattice wall. DM piles have been reported to have little effect as a liquefaction countermeasure, but to be superior in terms of construction cost and applicability around existing underground structures (Koga et al., 1986). However, there are experimental results implying that DM piles have reduced the shear deformation of unimproved soil and mitigated its liquefaction (Yasuda et al., 2003; Tanaka et al., 2003). Yamamoto et al. (2006) conducted dynamic analyses of ground improved with lattice- and pile-type DM. Their results showed that pile-type DM with an improvement ratio of more than 35% reduces excess pore water pressure generated by earthquakes. Furthermore, the new pile arrangement shown in Fig. 1(a) has been proposed to mitigate lateral flow induced by liquefaction. It was developed and has been verified using dynamic model testing in a 1 g field (Takahashi et al., 2010a; 2010b; 2013; Towhata et al., 2010, Morikawa et al., 2014). The DM piles in this configuration interrupt lateral flow in any direction, unlike those placed in square and triangular arrangements."

Jan 1, 2015

By Bill Zietlow

A micropile and soil nail underpinning system was installed to support a building immediately adjacent to a 25-ft deep excavation in downtown Salt Lake City, Utah. Both the building and the underpinning were instrumented to monitor deflections, rotation and crack growth. The underpinned structure consisted of a two story concrete masonry unit (CMU) building founded on shallow spread footings attached to a concrete high-rise building on spread footing two floors below grade. The face of the excavation was 10 in. in front of the underpinned building foundation wall. The underpinning system consisted of small diameter hollow bar micropiles installed with injection grouting techniques below the bottom of the excavation and attached to the underpinned structure by a concrete pile cap doweled into the existing footing. The lateral loads imposed by the soil under the underpinned structure were designed to be supported by the soil nail wall installed through the micropiles during excavation. The settlement monitoring instruments consisted of crack gages, optical survey prisms, high sensitivity vibrating wire water levels and biaxial vibrating wire tilt meters. They recorded maximum movements of approximately 0.1 in. of settlement, 0.05 deg. rotation (top of wall rotating away from excavation) and up to 0.08 in. of crack opening during the excavation until one month after the soil nails and shotcrete facing were completely installed. This movement was well within both the estimated settlement and the estimated settlement tolerance of the underpinned structure.

Jan 1, 2008

By Serhat Baycan, Mikias Yohannes

"Kuala Lumpur Karst is a complex limestone formation that is characterized by presence of cavities, solution channels, pinnacles and floaters. Basement excavations in such geological formations are usually challenging, mainly owing to the unpredictable rock head depths and potential for groundwater inflow. Any excavation support system should have adequate robustness and water tightness. Traditionally, Secant Bored Pile walls (SBP) with struts are the preferred option for karst ground. This paper discusses a cost effective and innovative alternative solution for a particular site – using Deep Soil Mixing (DSM) and using Contiguous Bored Piles (CBP) together with Ground Anchors (GA). The site, located around one of the busiest areas of Kuala Lumpur, is a 5,700 m2 commercial and residential development. A 16.0 m deep excavation was needed for four levels of basement and excavation support along the 275 m perimeter of the development. Within the site, the depth to rock head varied from 6 m to 19 m. The basis for each solution and conditions for its suitability are discussed in detail. Some design considerations and construction challenges are also presented. The performance of the two retention systems during excavation are presented, together with comparisons versus design predictions. Suggestions for future development are also given. Advantages of this approach compared to other traditional approaches are highlighted.1. INTRODUCTIONThe geology of Kuala Lumpur is among the most complicated and geotechnically challenging formations in South East Asia. The majority of the city falls into the Kuala Lumpur Limestone formation; which is a thick, highly-weathered and cavernous limestone. This formation is pure calcitic to dolomitic in composition, having infrequent schist and phyllite interbedding (Gobbett et al., 1973).The KL limestone has a highly karstic topography dotted with cavities, ravines, interconnected subterranean channels, pinnacles, overhangs, floaters and slump zones (Tan, 2006). This results in erratic bedrock profiles even within short distances. It is not uncommon to see a precipitous rock head incidence within short distances in the same site. In most parts of the City, the bedrock is typically encountered ranging from very shallow depths to about 30.0 m. The exception to this is at the heart of the City, where Kenny Hill formation prevails above the KL limestone. In such cases the limestone bedrock can be encountered much deeper. The erratic rock head profile and the highly karstic nature of the KL limestone makes it a geotechnical challenge requiring careful consideration of suitable engineering solutions.1.1 – Site DescriptionThe site, located in downtown Kuala Lumpur, is abutted by a busy street on the North. Before development, the site previously served as a car park. To the west an access road separates the site from an empty lot; while on the east, the lot is bounded by light weight residential and commercial buildings. On the south side, the site is bordered by a road that separates it from a prominent Shopping Mall in the City. A layout plan and an artist’s impression of the finished development is shown in Figure 1."

Jan 1, 1900

By Brett K. Mainer

In the summer and fall of 2007, Drill Tech Drilling and Shoring, Inc. designed and built three 24-foot inside diameter shafts in Northern California using soil mix panels for support. The soil mixing was performed using the Bauer Cutter Soil Mix (CSM) method, by which rectangular soil mix panels up to 71 feet deep were arranged in an overlapping manner to form a 24-foot inside diameter circle. The shafts were then excavated to depths up to 51 feet. One of the shafts was a test shaft and used only the soil mix panels for support. The other two shafts were located immediately adjacent to the Mokelumne River and were used as access pits for a microtunnel drive under the river. These two shafts had wide flange beams embedded in the panels and were supported with several levels of ring steel placed during excavation. This project was the first use of the Bauer CSM method in the United States. The CSM method has been used extensively in Europe and Asia, but never for this application and never with this high a loading criteria due to water head and microtunnel reaction forces. Soil conditions at the river crossing shafts consisted of sands, gravels, and cobbles over top of sandstone and conglomerate bedrock ranging in strength up to 5,000 psi. Groundwater was within several feet of the surface. The shafts were successfully completed between October 2007 and January 2008, and the microtunnel was successfully completed in February 2008. This paper provides discussion regarding selection of the shoring type, structural design, the soil mixing method, and the mix designs. Shaft construction, shaft performance, and the capabilities of the CSM equipment are presented.

Jan 1, 2008

By Donald Deardorff

"Helical piles often rely on the final installation torque for ultimate capacity verification. When helical piles are designed using traditional bearing capacity equations for deep foundations and field monitored for a specified final installation torque, a factor of safety equal to 2 is often allowed for the design. One of the more common methods of determining torque during helical pile installation is by correlating the differential pressure across a hydraulic gear motor to a torque. Most drive head manufacturers provide multipliers to convert differential pressure to torque for different drive head models. These multipliers are based on theoretical torque equations and vary with the planetary gear ratio, hydraulic gear motor displacement and drive head efficiency. Drive head manufacturers show a linear fit between the differential pressure and output torque with no scaling effect. Previous drive head testing performed by the author has confirmed that the drive head differential pressure to torque relationship is generally linear however there is a scaling adjustment needed. This results in a variation of multipliers across the differential pressure range for a given drive head.Eight hydraulic drive heads from three manufacturers were field tested by Foundation Supportworks, Inc. to compare the torque versus differential pressure curves with varying installation equipment, hydraulic line sizes and hydraulic flow rates. Differential pressure was monitored using three methods including pressure gages, PT-Tracker and an Ashcroft AT-100. Flow and temperature was measured using a Webtech system analyzer. Torque was measured using a Pro-Dig in-line torque transducer, a TruTorque indicator and a Chance Mechanical Dial in-line torque indicator. The current testing indicates that a change in installation equipment and/or a change in hydraulic flow rate may affect the torque versus differential pressure curve of a given drive head. The results of this testing also show that some of the methods for determining torque during helical pile installations may be unconservative, thereby resulting in safety factors less than required."

Jan 1, 2017

By Donald Deardorff

Helical piles often rely on the final installation torque for ultimate capacity verification. When helical piles are designed using traditional bearing capacity equations for deep foundations and field monitored for a specified final installation torque, a factor of safety equal to 2 is often allowed for the design. One of the more common methods of determining torque during helical pile installation is by correlating the differential pressure across a hydraulic gear motor to a torque. Most drive head manufacturers provide multipliers to convert differential pressure to torque for different drive head models. These multipliers are based on theoretical torque equations and vary with the planetary gear ratio, hydraulic gear motor displacement and drive head efficiency. Drive head manufacturers show a linear fit between the differential pressure and output torque with no scaling effect. Previous drive head testing performed by the author has confirmed that the drive head differential pressure to torque relationship is generally linear however there is a scaling adjustment needed. This results in a variation of multipliers across the differential pressure range for a given drive head. Eight hydraulic drive heads from three manufacturers were field tested by Foundation Supportworks, Inc. to compare the torque versus differential pressure curves with varying installation equipment, hydraulic line sizes and hydraulic flow rates. Differential pressure was monitored using three methods including pressure gages, PT-Tracker and an Ashcroft AT-100. Flow and temperature was measured using a Webtech system analyzer. Torque was measured using a Pro-Dig in-line torque transducer, a TruTorque indicator and a Chance Mechanical Dial in-line torque indicator. The current testing indicates that a change in installation equipment and/or a change in hydraulic flow rate may affect the torque versus differential pressure curve of a given drive head. The results of this testing also show that some of the methods for determining torque during helical pile installations may be unconservative, thereby resulting in safety factors less than required.

"Integrity tests refer to a variety of non-destructive tests (NDT) whose purpose is to measure or determine the quality and uniformity, and some- times dimensions, of cast-in-place concrete foundation elements. The tests are primarily aimed at detecting zones of poor quality concrete, voids, bulges, and/or necking.The non destructive integrity testing techniques in this section most generally used for drilled shaft testing are based on one of two physical principles - stress wave propagation or nuclear radiation. All of the stress wave methods involve monitoring a deliberately created vibration, usually of very low amplitude (strains on the order of ??). Some methods rely on direct transmission of the signal, while others rely on processing reflections of the imposed signal.The stress wave methods are inherently sensitive to vibrations from other sources, especially at frequencies that fall within the range of interest for the particular test being applied. Construction activity near the shaft being tested; such as: demolition jack-hammering, pile-driving, casing vibration, excavation and movement of track-vehicles are all known sources of interference that might render test data useless. The actual effect of such vibrations will vary with the type of activity, soil conditions and distance from the testing. The test operator must be able to recognize such interference, and the contractor should be prepared to cooperate with the testing personnel by stopping or moving the source of vibration. If this cannot be done immediately, testing should be postponed until the work in question is finished and the vibration source moved or shut down.NDT methods are not suitable substitutes for routine "topside" construction inspection as described in the Drilled Shaft Inspector’s Manual. However, these NDT methods do allow measurements of the quality of concrete placed in drilled shafts, which cannot be made from "topside" construction inspection. They should be considered supplemental to routine construction inspection as they do provide an additional level of quality control."

Jan 1, 2004

By Marcus Daubner, Karsten Beckhaus, Florian Bauer

The construction industry can and needs to contribute to a more sustainable world. Accordingly, geotechnical works potentially have a significant share. In this context, Bauer understands “sustainable products for geotechnical works” as those that may cause less emissions and increase the sustainability of construction activities. In order to structure the efforts and systematically pursue sustainable targets in the construction sector, and in the specialist foundation industry, the “17 sustainability goals” presented by the United Nations in their AGENDA 2030, can be used for general guidance and for continuous improvement. Benchmarks for relevant economic and social objectives, mainly with environmental aspects, are inevitable. The key parameter to sustainable products for geotechnical works in the focus of this paper is the optimisation of processes on site needed to fulfill the client’s building task, including the selection of technologies and construction methods with minimum environmental impact and minimum carbon footprint.

May 1, 2022

By Pierre Gouvin

This paper describes the design, installation and monitoring of a state of the art real time geotechnical/structural instrumentation monitoring system to facilitate tunnel construction under Interstate route I-5 in Seattle, Washington, USA. The project involved removal of existing highway foundation substructures on both North and Southbound lanes as well as the underground reversible high occupancy vehicle lanes. The system utilized state of the art 3-D pulsed laser scanning, wireless sensor networks, automated robotic total stations, tilt beam sensors, narrow angle tiltmeters, and in-place inclinometers. Dedicated real time data loggers, with a web based graphical interface, provided 24/7 access to critical measurements. In addition to the instrumented sections of wall and roadway subsurface which monitored physical measurements at known points, the pulsed laser scanning allowed complete site monitoring coverage where physical sensors were not located. This data allowed post processing at any location enabling the contractor and designer to respond to unforeseen structural responses to construction. Use of the instrumentation system resulted in the early detection of wall movement, and provided feedback to the designers to facilitate construction process changes in order to minimize further movement.

Jan 1, 2010

By Josef K. Alter

Long-term performance and behavior of post-tensioned ground anchors subjected to axial cyclic loading constitutes an important aspect of the stability, reliability and overall performance of wind turbine deep foundations. Axial cyclic loading of post-tensioned (PT) ground anchors in soils has not been thoroughly investigated as evidenced by the research conducted for this topic. This paper evaluates research test data, available literature, and industry expert opinion on the current status and problems of deep foundation post-tensioned ground anchor (PTGA) technology, as applicable to the wind energy industry. It also introduces a proposed design solution that addresses the problems of construction cost and long-term performance of wind turbine deep foundations in soils subjected to dynamic cyclic axial loading. Deep foundations using ground anchors for wind turbines have only recently gained attention as a possible viable alternative to the mass spread footings currently in use. One of the primary problems with general acceptance of current PTGA designs is the need for long-term anchor maintenance. The research that was conducted for this study indicates that current literature only partially addresses the many factors influencing load capacity and pullout performance of ground anchors. The lack of information indicates the deep foundation industry has fallen behind in designing and implementing new technology to improve safety and performance, ensure sustainability, reduce costs, and address environmental responsibility. This paper describes the significance of this problem as it applies to the wind energy market, and proposes a new technology solution. The research, expert opinion, and analysis presented by the author is used to support the premise that ground anchor construction cost and long-term maintenance can be reduced with PTGA systems using the Con-Tech Systems (CTS) patent-pending Groutable Void Form (GVF) technology.

Jan 1, 2010

By George J. Tamaro

In 1967 the Port Authority of New York and New Jersey undertook the construction of the World Trade Center (WTC) diaphragm walls, installation of the lateral support system and the excavation of the site, commonly referred to as the "Bathtub". The work took two years to complete. In 2001 the City of New York undertook the re-excavation of the site after the terrorist attacks. The recovery work will take eight months to complete. This paper describes the initial work on the WTC "bathtub" in the late 1960s and the recent work during the recovery.

Jan 1, 2002

By Dennis Nottingham

The need for deep compaction of submerged granular soils has led to improvements in this area. In 1971, L.B. Foster Company personnel patented a method of deep compaction using a vibratory pile hammer and pile probe. The technique had some success, but did not produce consistent results and thus found its way to obscurity. Other patents attempted to modify the technique by various probe modifications, but again without measurable improvement from a practical point of view. Solutions to economical deep compaction up to 100 foot depths particularly in saturated granular soils would have a great impact on the construction industry and new bulkhead structures being developed, thus PND was prompted into related research and development. The advent of higher horsepower vibratory hammers, coupled with PND engineers? experiments, observations and measurements, led to an ?H? pile probe design which has produced measured soil density improvements up to 250% using SPT ?N60? values as a measure.

Jan 1, 2013