Search Documents

By F. P. Hassani, H. B. Poorooshasb

"A kinematically admissible velocity field is applied to study the arching phenomenon in a cohesionless granular backfill placed between two rough vertical inflexible walls. The study is different from the previous works which are almost entirely based on statically admissible stress fields. It is shown that the development of arches is strongly influenced by the previous loading history of the backfill which controls the nature of the constitutive laws that govern the mode of stress deformation of the backfill. This preliminary study employs simple models in order to show the potential use of such an approach in evaluating and understanding mine backfill behaviour in the underground excavation. The pressure exerted on the floor supporting the backfill is also studied in some detail.INTRODUCTIONAlthough the importance of the design of mine backfill has been discussed extensively by a number of authors, i.e. Hassani et al. (1985), such theories have not as yet been incorporated in design criteria for underground mine backfilling operation . One factor that such theories must incorporate is the so-called arching action .The phenomenon of arching has been the subject of study by many researchers in the field of civil engineering and mining engineering. Among these scholars the works of Terzaghi (1943), Krynine (1945), Lusher and Hoeg (1964) and Handy (1985) are noteworthy. All these authors use a statically admissible stress field as a starting point to develop their theories. The approach taken by the authors of the present paper is completely different because they employ a kinematicallyadmissible velocity field. It is their belief that the arching phenomenon is closely linked to the interlocking of grains as manifested by the degree of dilatation of the granular mass when subjected to a shearing process.This paper is written in the following sequence. To define the interlocking quantitatively it is necessary to state the constitutive law governing the stress deformation characateristics of the granular mass. This is done in the next section as the law proposed by Poorooshasb and Pietruszazck (1985, 1986) is stated and simplified to suit the present analysis. Next the mode of formation of an arch in a simple system consisting of a mass of backfill sandwiched between two vertical rough walls of infinite extent is examined. The velocity field obtained from the above example is used to obtain solutions to two more complicated situations. The first situation assumes that the backfill is supported, in addition to the vertical rough walls, by a Winkler foundation at its base. The second situation assumes that the Winkler foundation has been replaced by a horizontal beam of uniform section and simply supported at its extremities. The findings of the study are summarized and their practical implications discussed in the concluding remarks."

Jan 1, 1989

By P. J. Noakes

Remote and isolated, located in a frigid, hostile environment, the Black Angel mine in Greenland had to create a warm social environment which would help attract and retain a stable work force of miners and support staff. The high cost of personnel turnover plagues many mines and, when the mine is inside the Arctic Circle, accessible by helicopters which are highly vulnerable to unpredictable weather conditions during the long, dark winters, the potential costs of personnel turnover become critical factors in the success or failure of the mining venture. Manpower planning should start from the date the engineers begin the technical design of the new mine. The plan should include provisions not only to ensure an adequate, skilled work force, but also to ensure a stable work force of people who are happy enough in the mining environment to want to remain, take their vacation and return to work at the mine. The skilled work force was assured with training courses of four months, designed to produce highly specialized underground workers from unskilled Danes and Greenlanders supported by trained Swedish and other Scandinavian miners. The stable social unit was assured by plans the primary attribute of which had to be flexibility. The accommodation changed from shared accommodation with communal washroom facilities to single accommodation with private washroom facilities. A recreational director was hired to help the workers make use of elaborate recreational facilities. A closed-circuit TV and radio system was installed to operate as a private broadcasting system using taped programs originally broadcast on European TV networks or developed by the mine personnel themselves. The liquor rules were changed and the mine manager became a licensed innkeeper responsible for the orderly operation of the Black Angel Bar in accordance with the Danish laws governing the services of a public bar. The result is a relatively stable work force. Some 35% of the people have more than two years' service with the company, Greenex A/S, and some 62% complete 10 months of service.

Jan 1, 1978

By Sanjeeva Latchireddi, Travis Orser

"Today’s high capacity semiautogenous grinding (SAG) mills expend vast amounts of energy and in doing so consume tons of shell liners and steel balls, while processing ore. The energy efficiency of these high throughput grinding mills can be attributed to the field of breakage and slurry discharge system. The charge motion and breakage of particles inside the mill depends on the shell lifters design, while the discharge of ground particles is controlled by the grate and pulp lifters. The limitations imposed by poor grate and pulp lifter design become increasingly apparent with increasing size of ag/sag mills and their operation in closed circuit. The design of these mill components has been largely based on trial and error and hence varies considerably between manufacturers. This paper discusses the use of two state of the art design tools - Millsoft™ and FlowMod™. Millsoft™ is an effective tool to design the shell lifters and optimize charge motion, whereas FlowMod™ simulates the slurry discharge system to design grate and pulp lifters. The application of these simulators will be discussed using case studies of full scale mills.INTRODUCTIONMany large mining operations around the world have one or more semi-autogenous (SAG) mills doing bulk of the work in their size reduction operation. The SAG mill is usually followed by a ball mill to finish the size reduction prior to the concentration step. In the past when primary, secondary and tertiary crushers fed material directly to large ball mills, the energy efficiency of the concentrator was determined for the most part by the ball mill operation, whereas now the energy efficiency of a plant often rests largely on the SAG mill operation. As a result mines have shifted their emphasis in optimization from ball mills to SAG mill"

Jan 1, 2005

By M. Rebolledo, N. Mora, G. Zarate

For decades, the mining industry has been focussed to find an efficient and economically attractive process for the leaching of chalcopyrite. Jetti Resources has developed a novel hydrometallurgical alternative to extract metals of value from mineral ores that the mining industry has struggled to process. Jetti’s catalytic technology, whilst being especially advantaged for extracting copper from low-grade and highly refractory minerals, such as chalcopyrite, seamlessly integrates with existing heap leaching methods and downstream processing operations. The technology uses a catalyst which weakens the metal-sulfide bond in the crystalline structure of the chalcopyrite mineral and alters the structure of the passivation layer allowing the leaching process to continue. Metallurgical test work was conducted to examine the effect of ore variability, in terms of grade and copper deportment. The results presented in this study highlight the amenability of the technology and demonstrate that it is possible to enhance leaching performance of copper primary sulfides over a wide range of copper grades, from 0.1 to 2.2%. Further, it is concluded that despite the copper grade, the tests with increasing chalcopyrite content render copper recoveries up to 4 times higher compared to the tests under non-catalyzed conditions. Jetti’s catalytic technology is currently being evaluated at larger scales, namely a commercial dump leach operation and 50-tonne crib tests. The results obtained thus far are compared to the results from conventional sulfide heap leaching tests. INTRODUCTION For decades, the mining industry has been focussed to find an efficient and economically attractive process for the leaching of chalcopyrite. Chalcopyrite (CuFeS2) is the most abundant and recalcitrant of the copper sulfides (Singer, 2017). Owing to its abundance and economic importance, it is the most demandable natural source for copper worldwide. In fact, the projected demand for copper is further expected to rise much higher beyond the current demand by the year 2020 (Panda et al., 2015). Therefore, it becomes imperative to find low intensity hydrometallurgical technologies for the extraction of copper from chalcopyrite in ores of such low-grades that are un-economic to concentrate and to augment the supply by extracting copper from ores with complex mineralogy that cannot be concentrated (Watling, 2013).

Jan 1, 2019

By Flavio Rojos-Tapia, Oscar Pereira-Cerda, Samuel Sánchez-Pino, Samuel Sánchez-Baquedano

"Pneumatic flotation was introduced to the Chilean Copper Mining Industry in 1993 by Ingeniería de Minerales S.A. (IDM). The technology is based on the designs of Dr. Rainer Imhof from Germany, who is the designer of several different types of pneumatic flotation cells, already sold through his Company Maelgwyn Mineral Service Limited (MMH). The company is represented by Ingenieria de Minerales S.A. (IDM) in South America.Pneumatic flotation, has been used in tough industrial applications .It has been successfully used for metallic ores such as copper sulphide and oxide minerals, copper slag, silica and silicates from iron magnetic preconcentrate (reverse flotation) and gold. It has also provided promising results when applied to molybdenum flotation. The latest applications, with ultrafine molybdenum particles in operating plants, is showing the V and G Cell (end model designed) as a real technological alternative to conventional flotation., The G Cell is an extremely high speed flotation machine with high selectivity which introduces the possibility of producing a final molybdenum concentrate with only one stage of cleaning. This is a completely new development in molybdenum flotation in the industrial circuit which has the potential to dramatically reduce the circulating load in the cleaning circuit. As a consequence the capital costs of future Molybdenum plants may also be reduced. The suitability of the G Cell will have to be determined on a case by case basis but it provides the metallurgist with an alternate flowsheet for consideration.The good performance of the G Cell can be explained by the high gas hold-up and very effective micro-turbulence which helps improve the attachment of solid particles to the bubbles. This technology may change our traditional concept of residence time in flotation. Additionally, the rotation phenomena introduced in the vessel of the G Cell ,creates radial separation forces which are critical to achieving a more rapid separation of the target minerals from the tailing. This results in a much reduced residence time requirement in the flotation machine. Some benefits associated with the use of the new G Cell are: less energy consumption, less maintenance costs, simple and reliable circuit to operate and a small area required for installing the circuits.As a result of the industrial experience in the Chile, the pneumatic flotation type G Cell can be regarded as a technology which must be considered as a replacement technology for the rougher and cleaner stages for fine particle flotation."

Jan 1, 2008

By J. Tuzo Wilson

Abstract A division of part of the Canadian Shield into provinces believed to represent former mountain belts is attempted, special emphasis- being laid upon radioactive age determinations, the relation of Archaean to Proterozoic rocks, and the structure of the Grenville province. Original data on the distribution of radioactivity within several batholiths and their connection with ore deposits are' presented. The possible growth of continents and a theory which explains the shape and distribution of the world's younger mountain and island areas are discussed and applied to the Canadian Shield in an attempt to explain how the growth and present structure came about. The relation of the major mining camps of northeastern Ontario to fault zones is discussed in the light of this theory. Introduction The valuable symposium issued by this Institute to celebrate its jubilees emphasizes the important role of major faults in determining the location of many ore deposits in the Canadian Shield. Many of these faults are known to extend for long distances. It is therefore widely appreciated that it would be of great value if the pattern, ages, and causes of these faults were better understood. This would be particularly useful if the relations of the major fault systems to petrological and metallogenic provinces and to former mountain belts could be established. Each year the volume of available data, and hence the chance of reaching a fuller solution of this problem, increases. This article is a review of the present situation. It is accordingly based almost wholly upon the work and ideas of others, which are gratefully acknowledged. Naturally, responsibility for the selection and marshalling of the data is the writer's.

Jan 1, 1949

By A. G. Doll

"Many power-based grinding models exist, and most operators are familiar with Fred Bond's ""third theory"". Bond's model is most commonly used to describe primary and secondary grinding to product sizes above, for example, 100 µm. Operators sometimes use Bond's equation to describe grinding in situations where it is not appropriate, such as fine grinding below 50 µm. Using an alternative model would be a better choice in this situation.Bond's equation is one in a large family of models. Related equations better suited to fine grinding include the “signature plot”, Von Rittinger's model and Charles' equation. These models have a similar form to Bond's and can be fit to industrial regrind mills and laboratory tests using the simple regression tools in the charts of computer spreadsheets. Operators will find that fine grinding calculations are both easier and more accurate when using the alternative equations to fit their regrind milling surveys or when performing laboratory regrind mill scale-up for plant design.None of these models are new: Charles' equation was published in 1957 and Von Rittinger's model was proposed in 1867. A quick refresh how to apply these equations can turn these oddities from the undergraduate curriculum into useful tools for plant optimization. They can be fit to any type of mill including stirred and tumbling ball mills.IntroductionBuilding a case for fine grind modelling requires reviewing some theory before building a framework for doing fine grinding calculations. The actual calculation procedure recommended is easy and can be applied by plant metallurgists. Don’t be frightened by the theory; the end result is reasonably simple.The observation that mineral breakage is related to the absorption of energy is usually attributed to Von Rittinger (1867). Lynch and Rowland (2005) describe that the ability to empirical test and calibrate energy models of breakage didn’t exist until the widespread adoption of electric motors in the mining industry during the 1930’s and 1949’s. A series of technical papers published by the Allis Chalmers company during the 1940’s demonstrate that they were attempting to do such a calibration using Von Rittinger’s model which is usually stated as: “the energy consumed in the size reduction is proportional to the area of new surface produced.”"

Jan 1, 2017

By C. D. Rowe, H. S. Mitri, J. Malki, I. Vennes

Ore extraction at great depths creates high stresses around mine openings, which can result in violent rock failure in one of various forms of strainburst. This is especially true with strong and brittle rocks, which can store a large amount of strain energy that is suddenly released at failure. The strength and brittleness of rocks have been extensively investigated in the past. The most widely accepted method for the determination of rock burstability is the strain energy storage index obtained from a non-destructive uniaxial load–unload test. However, the results of this method are not always conclusive, showing less repeatability when the target test load is changed. This study concerns itself with the introduction of microscopic analysis as a tool to help validate the strain energy index results when burstability cannot be warranted based on mechanical property tests alone. In this study, two types of rocks, namely, basaltic komatiite (BK) and felsic norite (FNOR) obtained from Canadian underground mines are examined. The selection is based on the premise that felsic norite is known to be burstable from the mine experience, whereas basaltic komatiite is not necessarily burstable. A total of 60 mechanical properties tests were conducted including uniaxial compressive strength, Brazilian tensile strength, and load-unload tests. Laboratory tests on FNOR consistently exhibit high burstability; however, the results for the BK tests are not conclusive. To seek explanations for the mechanical rock behavior, 18 thin sections were examined with optical microscopy and image analysis. The findings show the tested BK specimens are dominated by alteration products, and all primary igneous minerals are lost. There is minor quartz, garnet, carbonate minerals, talc, and serpentine, which give the rock its ductile properties. The FNOR specimens are found to be relatively fresh and supported by a strong network of plagioclase with minor pyroxene, biotite, and secondary micas, explaining the higher stiffness. This study demonstrates how optical microscopy can complement mechanical property tests to evaluate burstability of rocks.

May 4, 2025

By John Wilson

"The unconformity beneath 75 per cent or over 6000 km2 of the Athabasca Basin in Alberta lies within economically exploitable depths. The basement beneath this unconformity consists of an extension of the Wylie Lake Pluton, locally faulted and containing areas of mylonitic rocks. While the rocks of the Wylie Lake Pluton are not promising host rocks for uranium ore deposits, the areas of mylonites, graphitic rocks and possible remnants of granitegneiss would bear closer examination. One area of maficmylonites shows a weathering zone enriched in Si, Ca, Na, Pb, Ni, Ba, Co, Sr, Zn and U in addition to reported values of 0.08 oz/ton gold. This zone occurs beneath 800 m to 900 m of Athabasca Group sediments, but similar rock types are present beneath much thinner cover elsewhere. Detailed geophysical exploration is required over the area of thinner Athabasca Group rocks to define more precisely the areas of promising basement rock type.IntroductionThe Athabasca Basin in Alberta has considerable economic potential which has not yet been realized. The geological setting is closely analogous to parts of the basin in Saskatchewan which host major uranium deposits. Recent advances in geophysical techniques have led to deposits being located in Saskatchewan below 600 m of cover. This means that the unconformity between the Athabasca Group and the basement lies at exploitable depths over 6000 km2 or 75 per cent of the Alberta portion of the basin. Much of this area was only cursorily examined almost a decade ago. In addition, Alberta's new Metallic Mineral Regulations have clarified the regulatory situation in the area, and opened up much land for exploration. This article is based on Wilson's (1985a) study of the Athabasca Group and Wilson's (1986) work on the basement and alteration beneath the Athabasca Group in Alberta."

Jan 1, 1987

ABSTRACT Inco’s Iron Ore Recovery Plant was operated by Inco from 1955 to 1980 near Sudbury, Ontario. As exposures to specific nickel substances have been associated with adverse respiratory endpoints it is important to understand processes giving rise to such substances. This manuscript discusses the process and equipment, the propensity for aerosol formation, and operational procedures used by Inco in roasting a pyrrhotite concentrate, reducing the nickel in the formed oxide, leaching the nickel in ammoniacal solution, purifying the resulting solution, making green or black NiO, and producing iron oxide pellets. Industrial hygiene measurements are also reported.

Jan 1, 2013

By J M. Fletcher

The responsibility and scope of the Industrial Engineering Department, as organized at the Jeffrey mine, has been broadened to include any study, project or report that could result in more effective use of men, materials and equipment. Although still emphasizing wage incentives and co t reduction, much more varied work is now done, consistent with the in-.creased complexity of industry. Additional activities now include production, maintenance and inventory control improved job evaluation, packaging, labour utilization studies, technical sales liaison, mining, milling and service department n1ethods, plant layout, and specialized project analysis. Additional techniques include the extensive use of work .sampling and standard data. A recent trend has been toward increased emphasis on industrial relations, both in introducing change to the men and in providing requested explanations to Union stewards and officers. These new responsibilities have resulted in the development of specialists in some rather narrow industrial engineering fields, as well as the necessity for industrial engineering assistance in supervisory and job training.

Jan 1, 1963

By J. H. Fulton

Summary Considerable test work has been done with the detachable type of carbide bit. In general, these bits improved drilling operations, but at a bit cost .greater than was compensated for by the reduction in man-hours of labour. Too few bits continued in service for the possible drilling life of the carbide inserts, and technical improvements or lowered first cost, preferably .both, are indicated ?in order that the bits can be generally acceptable as an economical drilling tool. In ?preliminary test work, the drill rods .with ?one insert of the chisel-bit type appear to be more trouble-free, to have a longer life, and to give a somewhat lower bit cost per foot drilled, than other types. INTRODUCTION The object of this paper is to outline briefly the 'methods used and the results obtained in test work with tungsten carbide bits used in combination with the smaller bore, lighter weight rock drills. As various articles have appeared in the past few years giving the historical background ?and early development of carbide ?bits, this information will not be repeated. Table I lists the equipment used in the test work. The stopers weigh about 95 pounds and the jackhammers with airleg from 97 to 110pounds. The smaller rock drills are stated to deliver about 2,200 blows per minute at 1 to 30 rotation and to require 85 to 95 cubic feet of air at around 100 pounds pressure.

Jan 1, 1950

By Tony Lipiec, Greg Gosson

"When it comes to new mines being developed, there is a general industry consensus that most low-hanging fruit has been picked. Many projects currently in the mine development pipeline have been around for decades, but were held back because of technical challenges. Future development of these deposits will likely require access to the public capital markets, and in Canada that means providing scientific and technical disclosure on these deposits in compliance with NI 43-101. As many of these “challenged” projects have metallurgical issues, the companies that own the projects need to ensure their metallurgical Qualified Persons provide transparent disclosure regarding proposed solutions to those issues.This paper provides an overview of the disclosure requirements under NI 43-101 that are pertinent to metallurgists, and other Qualified Persons who prepare technical disclosure regarding the metallurgical characteristics of a mineral project. It lists the triggers for a technical report under NI 43-101 and Canadian stock exchange policies, and identifies the sections of the report that should involve input from a metallurgist or process engineer. It briefly outlines new civil liabilities under Canadian securities laws that increase the possible consequences for not complying with the technical disclosure standards.These materials are provided for general information purposes only and do not constitute legal advice. Readers are advised to seek specific legal advice from their own legal counsel in relation to any decision or course of action contemplated."

Jan 1, 2010

By Adil Aledresse, Louis Mercier, Laxman Amaratunga

"The development of high capacity adsorbents with uniform porosity denoted, MP-HMS (Mercaptopropyl – Hexagonal Mesoporous Structure) using nanotechnology, and their ability to extract gold from solution, is presented. The preparation of highly effective heavy metal ion adsorbents by the incorporation of thiol moieties into the pore channels of mesoporous silica molecular sieves has been the subject of many nanotechnology research investigations. The unique feature of these nanoporous adsorbents is their ability to adsorb gold ions from ultra-low concentration solutions like mine effluent as well as from leached solutions in gold mills. The preliminary studies from laboratory simulated gold solutions show that the adsorption capacities of these materials are also among the highest reported. MP-HMS has shown the capability to adsorb 370 mg gold per one gram of the nanomaterials from Tetrachloroaurate solution (up to 37% of their weight). Experimental studies indicated that the maximum adsorption of gold (as high as 99.9% recovery). The current studies will be extended to investigate the interaction of ionic gold complexes with nanomaterials. Future development of this work may lead to either to replace the conventional CIP/CIL processes or use nanomaterials in tandem with the former, suggesting plausible use of mesoporous material in pulp, MIP or in leach, MIL, as a novel gold extraction process.INTRODUCTIONGold typically occurs at very low concentrations in ores less than 10 g/t or 0.001% (mass basis). At these concentrations the use of aqueous chemical (hydrometallurgical) extraction processes is the only economically viable method of extracting the gold from the ore. Typical hydrometallurgical gold recovery involves a leaching step followed by the separation of the gold bearing solution from the residues, or adsorption of the gold onto activated carbon adsorbent. After elution from the activated carbon the gold is further concentrated by precipitation or electrodeposition."

Jan 1, 2008

By T. Hofbauer, M. J. Dry, G. B. Harris, C. W. White

"Urban Mining is a term that is increasingly being used, and represents an appreciable source of secondary materials for the metals extraction industry, a source that does not incur mining costs, but does, at present, incur considerable disposal costs. Electric Arc Furnace Dust (EAFD) is probably the most common of these materials, with an estimated global production of 8 million tonnes annually, of which 1 million tonnes is generated in North America. The contained annual metal value in EAFD at current prices is of the order of $6 billion, yet, apart from the zinc, virtually none of this is recovered.Despite many attempts over the years, with pyrometallurgical, hydrometallurgical or hybrid processes, currently the only commercially viable method of treating these materials is smelting in a Waelz Kiln (or a Rotary Hearth Furnace), which essentially recovers only the zinc, in an impure oxide form, and generates a secondary slag waste, which is still toxic and requires disposal. This paper describes the development of a chloride-based treatment process to recover all components of the EAFD in a marketable form, which centres around the novel hydrochloric acid recovery and recycle operation. Laboratory, miniplant and pilot plant data are presented, leading to the definition of a viable process flowsheet enabling the recovery of pure iron and zinc products (the principal components of EAFD), together with secondary products such as copper, silver, lead, cadmium, magnesium and manganese. A rigorous mass-energy balance is used to examine the preliminary economics involved."

Jan 1, 2014

By C. O. Brawner, J. Kalejta II

"The classical approach to control rock fall and ravel in open pit mining has been to use catch benches. The width and volume of benches is most dependent on the bench height, size of loading equipment, blast damage to the face and mining regulations. This was compatible with open pit slopes of less than approximately 45 degrees.As our understanding of rock mechanics and blasting control has improved over recent years, much steeper rock slopes can be developed at many open pit mines. However, narrower benches result in less rock fall capacity.The transportation industry has been very successful in using catch fences to protect highways throughout North America and Europe for years. The authors recommend that cable and ring net fences have a potential major application in open pit mining to allow steeper rock slopes with significant economic benefit. This paper outlines the application, design and operation of catch fences in surface mining for specific conditions. Typical case examples are presented."

Jan 1, 2002

By A. G. Darnley

"The Geological Survey of Canada is devoting consider-able effort to finding ways to make airborne radiometric measurements both quantitative and reproducible. Equipment has been designed by Atomic Energy of Canada Ltd. to provide high count rates in order to minimize statistical uncertainty, this being essential to justify applying terrain clearance and Compton scattering corrections to the data. Correction factors have been determined experimentally and can be applied automatically. Considerable ground work has been undertaken in parallel with equip-ment development in order to determine field parameters.Two airborne gamma-ray spectrometers are described. One is based on three 5-by 5-inch Nal(Tl) detector crystals and is used in a helicopter; the other employs twelve 9-by 9-inch detectors and is used from a Skyvan aircraft. The former is being used to investigate the range of radiometric response from specific rock types, and for the correlation of ground and air measurements; the latter has completed initial trials and will be commencing experimental surveys during 1969.Results are given to show the comparative sensitivities of the various detector sizes, and operational requirements for a gamma-ray spectrometer survey are discussed briefly."

Jan 1, 1970

By L. R. Plitt, A. A. Turak, B. C. Flintoff

"Since the publication of empirical cyclone models by Lynch and Rao in 1975 and by Plitt in 1976, the technical literature on this subject has consisted primarily of reports of applications, with only a few articles discussing basic modifications or enhancements in model form. In fact, most of the modelling eff ort in this period has been concerned with theoretical models based on the hydrodynamics of multiphase flow. (Preliminary resutls have been encouraging, however, it will be some time before this approach reaches the practical application stage.) This paper presents a review of empirical cyclone modelling technology, with an emphasis on developments since the mid 1970s. The topics addressed include homogeneous and heterogeneous ores, parameter estimation techniques, parameter confidence intervals, and the introduction of a new conceptual model of cyclone operation.IntroductionSince their first reported application in the mineral industry by Driessen (1939), cyclones have become a common unit operation in all of the process industries. The widespread use of the cyclone stems from its relative low cost and its versatility. It can be employed to carry out liquid-liquid, solid-liquid and solid-solid separations. It is the area of solid-solid separation which is of greatest interest to a mineral processing engineer. Historically, this area was divided into two application categories: (I) Separation according to density, the cyclone washer, and, (2) Classification according to particle size, the cyclone ciassifier. (When water is the carrier fluid, the cyclone is more often called the hydrocyclone. For the purposes of this paper the two names are used interchangeably). Classification is the principal application in mineral processing circuit s. Within this category, the cyclone is most commonly employed to provide some positive control over the size distribution of product from a grinding circuit. Other uses include sand-slime separation prior to froth flotation and mill tailings treatment, either for dam construction or in backfill preparation."

Jan 1, 1987

By R. J. Traill

Introduction Following the discovery of high-grade deposits of pitchblende in the Great Bear Lake area of the Northwest Territories by Mr. Gilbert LaBine in May, 1930, samples were submitted to the Mines Branch for examination and investigation as to suitable methods of treatment (1). The purpose of this paper is to present, briefly, the results of the investigative work conducted on the ores and an outline of the methods developed for the extraction of the radium content and recovery of the by-products. The paper is presented in two parts. Part I gives a review of the history of radium production and of the principal processes used in other countries. Part II describes the work and gives the results of the Mines Branch investigation. Part 1-Radium Production In Other Countries Historical Outline Uranium was discovered in 1789, and more than a century later Madame Curie, while studying the physical properties of this element, observed that the ore of uranium exhibited greater activity than the pure uranium com-pounds she had prepared and traced the cause to the presence of a new element which she named radium. Eventually, research proved radium to be a disintegration product of uranium, and always present in uranium ores.

Jan 1, 1933

By P. J. Mehrfert

"Recovery of mineralized coarse particles is notoriously low in conventional concentrators that treat copper porphyry ores. The application of coarse particle flotation techniques has the potential to achieve comparable metallurgical performance at significantly coarser primary grind sizings. ALS Metallurgy has been conducting both internal research and commercial test programs to investigate the potential of Eriez HydroFloatTM technology on copper sulphide ores. Test data indicates that significant improvements in the recovery of copper sulphide bearing particles between 200µm to 850µm can be achieved using Hydrofloat technology compared to conventional flotation techniques. This paper summarizes the results from a selection of test programs that includes recovery by size data from both conventional flotation and HydroFloatTM tests. An explanation of the apparatus and test procedure will be given. Mineralogical analyses of the test products and characteristics that limit metallurgical performance will be discussed.Description of Apparatus and Test ProtocolThe HydroFloatTM laboratory cell is a clear plastic column with an internal diameter of 14 cm. Water and air are introduced to the cell through a circular manifold located in the lower portion of the cell. The cell has a conical bottom which directs slurry to a pinch valve that controls the discharge of tailings. Feed solids are introduced to the upper portion of the cell in slurry form. The cell is operated in a manner such that the manifold water creates a teeter bed zone of suspended solids in the middle portion of the cell. Tailings exit the bottom of the cell at a high pulp density, and most of the introduced water overflows the top of the column and is collected in a launder. Particles with a hydrophobic surface may attach to air bubbles that percolate through the teeter bed, rendering them sufficiently buoyant to be transported to the overflow launder.Three significant features of this arrangement enhance the potential to recover coarse, low grade particles by flotation techniques. Firstly, the hindered settling conditions created by the rising column of water allow coarse particles to become buoyant once attached to a modest sized air bubble. Secondly, the flow conditions within the cell are relatively quiescent compared to a conventional flotation cell that utilizes an agitator. This allows particles that have limited hydrophobic portions of their surface, due to a low content of exposed sulphide mineral, to maintain a somewhat fragile attachment to air bubbles long enough for successful recovery to the overflow. Finally, the absence of a froth phase at the top of the cell allows particles attached to air bubbles to immediately exit the vessel, reducing the potential to drop back into the pulp phase as bubbles burst or coalesce."

Jan 1, 2017