Search Documents

By K. H. J. Clarke

"ALTHOUGH nickel was not identified as a separate element until a Swedish scientist, Axel Frederick Cronstedt, did so in 17 51, its utilization dates from pre-historic times. From its humble beginnings nickel has grown in importance until, today, in our clocks, television sets, automobiles, and air-planes, in our bridges, tableware, farm implements, and the equipment which processes our food, it is constantly at our service.For convenience in assembly, data and information relative to The Marketing of Nickel will be outlined in five phases: (A) Sources, (B) Distribution, (C) Utilization, (D) Market Development, and (E) Conclusions."

Jan 1, 1960

By George F. Crocker

Introduction The Helen mine and the Victoria mine of Algoma Ore Properties, Limited, in the Michipicoten district, Ontario, are 120 miles north of Sault Ste. Marie, on the north shore of lake Superior. They are on the Algoma Central railway between Hawk Junction and Michipicoten Harbour. Between them, these mines have produced 10,757,113 tons of iron ore. From 1900 to 1918, 2,823,369 gross tons of brown ore was shipped, and from 1939 to the end of 1949, 7,933,744 tons of siderite was produced from the open-pit operations and underground development. The finished product, known as 'Algoma sinter', is shipped to blast furnaces both in Canada and the United States. The iron-ore bodies are a part of a tabular shaped area of iron formation that extends over a length of more than 10,000 feet and has maximum width of 1,000 feet. The two siderite orebodies, known as the Helen and Victoria, are separated by two diabase dykes. The Helen orebody is 1,600 feet long with a maximum width of 250 feet and the Victoria is 1,200 feet long with a width comparable to the Helen. These orebodies are considered to be a replacement of the original rock by iron carbonate. The introduction of the iron-1bearing material probably occurred after the development of the major folded structures. The open-pit mining of siderite started in the Helen ore body in 1939 and continued until 1945. During this period, 3,853,395 tons of ore was mined. Open-pit mining started in the Victoria body in 1946 and is still being carried on. Underground development commenced in September, 1947. Diamond drilling and surface sampling had shown the Helen deposit to average 35.61 per cent Fe and 7.28 per cent SiO2, and the Vi.otoria deposit 33.73 per cent Fe and 10347 per cent SiO2?

Jan 1, 1950

By P. Oyanader

"In 2001, the Catholic University of Chile undertook a maintenance benchmarking study of six open pit copper mines having mill capacities varying between 18,000 t/d and 156,000 t/d, and collectively responsible for 58% of Chilean copper production. This paper describes the methodology used to conduct the study, as well as the overall results. Key performance indices were selected to measure the effectiveness, efficiency, and development of the maintenance process. Using a balanced scorecard philosophy, these indicators were divided into client satisfaction, financial, internal process, and learning and growth indices.Maintenance was found, on average, to be responsible for 44% of mine production costs. Percentage planned maintenance of equipment fleets was found to be low by world standards, averaging 35%, 56%, and 44%, respectively, for blasthole drill, shovel, and haul truck fleets. Fleet availabilities were found to be significantly influenced by the percentage of planned maintenance achieved, while maintenance cost per equipment was found to decrease non-linearly with increases in percentage planned maintenance. Investment in technical training (including planned maintenance practice) was found to be low by global standards. The paper concludes that fleet availability and maintenance costs in Chilean open pit operations could be considerably improved by improving and/or developing maintenance planning standards, and investing in training personnel in planned maintenance techniques"

Jan 1, 2005

By S. Kelebek, C. Gibson, M. Aghamirian

"Global niobium production is currently dominated by three operating mines, Araxá and Catalão in Brazil, and Niobec in Canada. Although over 90% of the world’s niobium is mined and processed in Brazil, a number of high grade niobium deposits exist worldwide. The advancement of these deposits depends largely on the development of operable beneficiation flowsheets. Pyrochlore, the primary niobium bearing mineral, is typically upgraded by flotation with amine collectors at acidic pH, and often includes a reverse gangue flotation stage prior to pyrochlore flotation. Challenges related to the flotation of niobium ores include complicated flowsheets which require pulp pH adjustment from alkaline to highly acidic conditions, difficulty recovering fine grained pyrochlore, producing concentrates that meet specifications, and minimizing the losses to reverse pre-flotation gangue concentrates, slimes, and tailings. The specific flotation challenges associated with different niobium ores are discussed. In some cases, the use of alternate flotation reagents and flowsheets are required to achieve reasonable gangue rejection and maximize recovery, particularly of very fine pyrochlore grains.INTRODUCTIONNiobium is a transition metal primarily found in the oxide minerals pyrochlore (Ca,Na)2Nb2O6(OH,F) and columbite (Fe,Mn)Nb2O6. After physical upgrading, pyrochlore is converted into a ferroniobium product which is largely used in the production of high strength low-alloy steel. Today’s niobium market is dominated by the Companhia Brasileira de Metalurgia e Mineração, whose Araxá operation produces over 80% of the world’s niobium. There are two smaller operations, Niobec in Canada, and Catalão in Brazil, which account for the remaining production (U.S. Geological Survey, 2013).A number of niobium deposits exist globally, their advancement dependent on the development of operable beneficiation flowsheets. Pyrochlore, the predominant niobium bearing mineral, is commonly upgraded by flotation with cationic amine collectors in acidic pulp conditions. However, many niobium ores do not respond to this typical flowsheet because they are either highly refractory or niobium deports to other minerals such as columbite, ilmenite and rutile, which are not as responsive to this reagent scheme (Bulatovic, 2010). Other reagents, such as alkyl hydroxamic acid, have been studied extensively and while promising, are not without their own inherent issues including lack of selectivity over iron oxide minerals, and high addition rates (Ni & Liu, 2012; Gorlovskii, Eropkiny, Koval, Strelstin, Khobotova, & Shtchukina, 1968; Gorlovskii, Khobatova, & Shtchukina, 1966).It is the aim of this report to highlight the challenges associated with the physical upgrading of niobium minerals through examination of the flotation behavior of two different ore systems. In order to overcome these challenges it is important to thoroughly understand the limitations of typical flowsheets/reagent schemes currently employed in operation."

Jan 1, 2015

By C. J. Brown

Controlling the level of impurities in copper refinery electrolytes is essential to achieving acceptable cathode purity. Purge of electrolyte is not an entirely satisfactory solution since the cost of neutralization, waste disposal, and replacement acid can be appreciable. The APU® process utilizes ion exchange resin to sorb sulphuric acid while rejecting metal salt impurities. Extensively employed for recovery of waste pickling and anodizing acids since 1977, the system is now being used at several refineries for removal of contaminants such as antimony, bismuth, iron, and nickel. The purified acid, which is recovered from the resin by water elution, is recycled back to the refinery tank-house, while the metals are typically recovered from the de-acidified by-product solution by precipitation.

Jan 1, 2005

By J-L. Tang

A new rhcoforming processing of Al alloys with component shaping systems apart from slurry preparation systems is experimentally exploited, using the reversible multilevel-speed electromagnetic stirrer, the slurry transfer tool and its coating, the thin plate sample with five steps and rheocasting mould, all of which are independently developed. The results show that semi-solid A356 alloy slurry with shape factor of about 0.85 and particle size of 70~80 µm (under air-cooling condition) could be prepared in 20~25 s, fully meeting the production rate of high pressure die casting. The slurry could be smoothly transferred from the slurry preparation equipment to the rheocasting shot chamber while the slurry temperature of slurry decreases by no more than 3 . The tensile strength and elongation of the semi-solid rheocasting samples could be respectively increased by 11.6~18.2 % and 42.5~50 % compared with the traditional liquid die casting ones, and the rheoforming processing has close affinity with the traditional hot working processes.

Jan 1, 2007

By Sanjiv Dhanjal

"Often mineralogy dictates the physical properties of a material rather than chemistry. This in turn affects how that material behaves in a process plant, and whether optimum conditions for refining one mineral are different to those for refining another. For example how does refining copper from chalcopyrite differ to refining copper from bornite?Minerals are naturally occurring inorganic solids that have a definite chemical composition and an ordered atomic (crystalline) structure. X-ray diffraction is a common and highly developed method to identify and quantify minerals. X-rays are fired onto a material and the mineral is identified by the angles where the diffracted X-rays are in phase.Most X-ray analyzers are laboratory based. A sample is prepared and analyzed by a detector that travels in an arc to collect the diffraction pattern. COSMA has a curved detector which picks up the complete x-ray pattern instantaneously. Therefore, material is collected and transported through the machine where is it is analyzed continuously.COSMA measures about 0.5 tons of material per day, while laboratory analyzers measure a few grams at a time. Real time data trends are produced allowing for improved process evaluation and automatic control. The COSMA on-line system has taken X-ray diffraction out of the laboratory into the field.There are a number of systems in operation in cement production. It is recognized that on-line mineral analysis has a role in many other processes. This paper presents the technology and invites further discussion should the technology be beneficial to members of the audience.INTRODUCTIONThis article describes COSMA, a system that provides direct and continuous on-line mineral analysis using X-ray diffraction in the field. While X-ray diffraction is a common technique used in mineral analysis, the time from sampling to analysis can be hours and plant operators typically do not get the data in time to control a process or respond to an upset. COSMA provides rapid measurement, analysis and feedback of data, in real time. This provides powerful information that can be used to optimize operation, thereby reducing costs and increasing quality."

Jan 1, 2009

By T. G. Joseph

"The Oil sands-Equipment Interactions Program (OsEIP) is a collaborative research venture between Syncrude Canada Ltd., James Progithin International Ltd. (JPi), the University of Alberta, P&H MinePro, and Caterpillar Inc. The objective is to better understand the behaviour of oil sands as it interacts with mining equipment, in particular, large trucks and shovels. With a move to ever larger equipment, mining oil sands of highly variable bitumen content, ground stability comes into question. This paper outlines this aspect of OsEIP and provides some insight into how some of the findings enable an improved understanding of oil sands behaviour that may impact large equipment design, operational and maintenance strategies. IntroductionThe mechanical behaviour of oil sands in the underfoot and in the face yields some of the harshest stability and digging conditions of any mining environment. High maintenance costs from truck and shovel fatigue failures predominate as a result of ground stability issues. Wear rates of shovel and dozer ground engaging tools (GET), rollers, roller paths and crusher screens result in costly and frequent replacement, or even more frequent and costly sacrificial wear zone building. From the shovel face to the crushers and screens, dry oil sands mechanics affects the degree of fragmentation and, ultimately, bitumen production.An increased knowledge of the behaviour of oil sands with respect to stability, fragmentation and abrasion, etc. would enhance the long-term equipment design process at the vendor level, and provide the end user with improved short-term operational guidelines and long-term strategies for future purchases and operation. Truck vendors recognize that the interaction between operator, seat, frame, suspension, tires and oil sands is unclear, and must be better understood before proceeding to next generation designs. Similarly for shovel manufacturers, the relationship between bucket/dipper motion, carbody, side frame, rollers, track and oil sands follow in the same vein."

Jan 1, 2002

By Bruce Conard

For many years, Bruce Conard has been engaged in reading about and discussing the desired sustainability of the mining and metals resource industry. He has, however, become concerned that there is a greater issue that requires our urgent attention: what challenges do we face as a global society? His Distinguished Lecturer presentation traces the idea of environmentally sustainable economic development but concludes that a business’ interest in its sustainability is predicated on the sustainability of our global society. Conard reviews some of the most serious challenges, including population growth, clean energy supplies, freshwater availability and climate change, and calls on scientists and engineers not only to apply their skills in helping solve these challenges, but most urgently, to speak with intelligence and passion about the need to act now.

Jan 1, 2014

By A-A. Bogno, Ch. -A. Gandin, A. Maitre, H. Henein

Most metallic materials are produced from their liquid state. In order to control the properties of industrial products, it is very important to understand their solidification path and the resulting microstructures which can be significantly affected by melt undercooling. High undercooling results in rapid solidification and a refined microstructure with minimal microsegregation. This paper reports on the analysis of rapidly solidified Al-Cu droplets obtained by a single fluid atomization process, Impulse Atomization. A quantitative analysis by Rietveld refinement method of the Neutrons Diffraction data was carried out to determine the fraction of the intermetallic Al2Cu. Knowing the fraction of Al2Cu, the eutectic fractions and corresponding dendritic and eutectic undercoolings were estimated using the metastable extensions of solidus and liquidus lines of the Al-Cu system calculated by Thermo-Calc. In addition to this work, a model of microsegregation coupled with ThermoCalc software via TQ (application programming interface of ThermoCalc) and the Wang-Beckerman model for dendritic growth velocities has been developed for binary alloys. This has led to the development of a phenomenological relationship between primary phase undercooling and initial growth velocity. A comparison of estimated primary undercoolings using a coarsening model with the adiabatic undercoolings for each alloy composition has confirmed that solidification occurs under adiabatic conditions during recalescence.

Jan 1, 2014

By B. Tonn, F. Kröger

"The continued development in engine technology is leading to an augmentation in power density which steadily elevates the requirements for thermally and thermo-mechanically highly loaded components such as cylinder heads and pistons. Due to these high performance requirements conventionally applied Al-Si alloys have reached their application limits, since their mechanical properties deteriorate quickly under the influence of heat. Improved applicability is given by Al-Cu-based casting alloys which have a superior high-temperature strength than Al-Si alloys. Since Al-Cu alloys exhibit insufficient casting characteristics, especially regarding hot tearing susceptibility and increased tendency for porosity, it is currently not possible to cast geometrically complex components in robust permanent mold casting processes. The further development of Al-Cu alloys is aimed at finding an optimum between improved castability while high-temperature strength and thermal conductivity are not deteriorated. It is known that a high amount of eutectic reduces the hot tearing susceptibility of an alloy, but it reduces thermal conductivity at the same time. In this paper it will be presented how the conflicting objectives – improved high-temperature strength, good thermal conductivity and reduced hot tearing susceptibility – can be brought together to develop an optimized Al-Cu alloy for application in permanent mold casting.INTRODUCTION At the beginning of the 21st century car, engine blocks were primarily made of gray cast iron (GJL). Less than half a decade later, the choice of material had shifted towards lightweight materials. Ever since, the car engine manufacturing is dominated by aluminum-based alloys. The weight of car engine blocks could thus be reduced by around 50% due to the lower specific weight of aluminum alloys compared to gray cast iron. Furthermore, the high thermal conductivity of aluminum alloys allowed a reduction of complex cooling channel systems and thereby promoted the advancement of this material group. The further development in engine technology leads to an augmentation in power density which elevates the requirements for thermally and thermo-mechanically highly loaded components. For example, in diesel-powered car engines the upper required limits can reach an ignition pressure as high as 230 bar and gas temperatures of up to 1000°C. Thereby, thermal loads can cause high alternating thermal stresses (Grzincic, 2003) which can effectively be reduced by providing high thermal conductivity."

Jan 1, 2017

By Christopher P. O?Connor

Stereolithography is a well known rapid prototyping technique in the manufacturing sector. Essentially it is a three dimensional printing process that produces plastic prototype parts from standard CAD files. At present, Canadian mining companies are not fully aware of the potential of Rapid Prototyping Techniques (RPTs) for their production and mine design systems. Mining engineers and geologists attempt to visualize and understand the characteristics and layouts of orebodies on computer models and in cases where it is decided to develop physical models, the process is time consuming based on simplified constructions. Rapid prototyping techniques (RPTs) such as stereolithography can facilitate engineers and geologists to quickly and with satisfactory accuracy to visualize sections of orebodies and evaluate alternative ore extraction techniques using 3D solid models. The research discussed in this paper is carried out by the Laurentian University Mining Automation Laboratory (LUMAL) in collaboration with the Department of Mines Research of Inco Limited and the Integrated Manufacturing Technologies Institute (IMTI) of the National Research Council of Canada. The main objective with this research is to evaluate the applicability of state-of-the-art RPTs (e.g. stereolithography) to underground hard rock mining systems. RPTs can play a significant role in accelerating the design and development process of mining systems.

May 1, 2002

By John Blackshaw

NEW sources of supply of tungsten concentrates became necessary when the flow from the Far East was blocked in 1942. In Canada, one source has been noted in the workings of the Hollinger mine at Timmins, Ontario. For many years, a small amount of scheelite had been removed with the gold ore, and an appreciable tonnage of scheelite still remained in the mine. At the request of the Dominion Government, a plant was built to recover this scheelite in the form of a concentrate that could be used by the alloy-steel industry without further preparation. The plant began operating early in March, 1942, and a small tonnage of ore, carrying scheelite and gold values, has been treated daily since then. The possibility of recovering the scheelite had been considered on several previous occasions. Each time the proposal had been given up because the total profits from the enterprise were estimated to be insufficient to repay the capital cost of building the recovery plant. At the time the plant was built, additional information had been gathered about the tonnage and grade of the scheelite ore in the mine, and several thousand tons of ore grading higher than 0. 25 per cent WO3 (tungstic trioxide) were known to be available.

Jan 1, 1943

By Lam. E. K., J. W. Jarvi, B. P. Bharadwaj

"The Rabbit Lake Operation is located in Northern Saskatchewan on the western shore of Wollaston Lake approximately 800 km north of Saskatoon, Saskatchewan.The Operation is owned by a joint venture of Cameco Corporation and Uranerz Exploration and Mining Limited. Cameco is the operator.The Mill started production in June 1975 under the ownership of Gulf Minerals Canada Limited and over the past twenty years has increased the rated production capacity to over twice the original design.The Mill was originally designed to process 485,000 tonnes per year of ore with an annual production of 2.0 million kg of U308 (yellowcake). During the past ten years changes in ore sources and process modifications have led to increased milling capacity and production targets. The Mill has treated a total of 8.6 million tonnes of ore and produced over 40 million kg of U308 in the twenty year period, despite the shutdown and cutbacks in operating time since 1989.The 1995 tonnage throughput was 206,000 tonnes per year. Annual production though has risen to 3.6 million kg of yellowcake despite the departure from full-time to half-time operation in 1991 (7 up-7 down). The forecast for the coming years will see tonnage rising from 300,000 to 570,000 tonnes, production of 4.5 to 5.4 million kg of yellowcake and an anticipated return in the year 1998 to full time operation.This paper will give a brief history of the Mill and focus on the present flowsheet and recent improvements to the process."

Jan 1, 1996

By R. Lasmanis, W. C. Utterback

"The Mount Tolman porphyry Mo-Cu deposit is 64 km south of Republic, Ferry County, Washington. It occurs in the composite Keller Butte pluton, which consists of the Keller Butte porphyritic biotite granite and granodiorite, the Mount Tolman quartz porphyry granite, and the Meadow Creek biotite granite phases. The three phases range in age from 61.3 Ma ± 2.3 Ma to 55.7 Ma ±2.0 Ma. The stockwork deposit occurs in the Keller Butte phase above the contact with the Mount Tolman quartz porphyry granite.Mount Tolman is a hybrid calc-alkaline deposit that has features of both a Climax-type and a plutonic type. Prior to post-ore faulting, the deposit had a flattened hood like shape. In plan it is elongated- 1.6 km wide, 3.2 km long, and up to 609 m thick. The orebody has a 292 o strike. It contains a geologic reserve exceeding 2.18 billion tonnes of ore averaging 0.093% MoS2 and 0.09o/o Cu using a 0.048% MoS2 cutoff. Of this total, 816 million tonnes of measured and indicated ore averaging 0.097% MoS2 and 0.09o/o Cu could be mined by open pit with an overall waste-to-ore ratio of 0.91 to 1.The deposit is a stockwork of quartz and quartz-sericite-pyrite veins and fracture fillings that contain molybdenite, chalcopyrite, sphalerite, and magnetite. Five separate episodes of fracturing and mineralization produced the orebody and were followed by four additional episodes of fracturing with sulrgrade mineralization. The Mount Tolman deposit contains propylitic, argillic, phyllic, topaz greisen, and potassic alteration zones. Extensive silicification overlaps the K-feldspathized, quartz-topaz, and phyllic alteration zones."

Jan 1, 1995

By R. Biss

"Niobium or columbium, as usually called in North America is becoming a more and more important metal in the industrial world because of its attractive properties.Eventhough discovered in the early nineteenth century, it was not until the 1930's that its use became more widespread. The discovery of large commercial deposits in the late 1950's and the demand of industry for steel with high strength and toughness further promoted its use. To assure its adequate supply new or-e processinr technologies had to be developed. So, beside the traditional gravity concentration, the flotation process was employed for the partial upgrading of pyrochlore concentrate at S8ve (Norway) plant in 1953. The flotation process was equally used at St-Lawrence Columbium plant in the province of Quebec, Canada. The new plants at Araxa and Catalao in Brazil and at St-Honore, Canada, which supply almost of all niobium used today in the non-Communist world, also adopted the flotation process. The processes using long chain aliphatic rnonoarnines, diamines or sulfonates as collectors proved to be difficult especially on weathered types of ores or on those having a substantial content of silicate gangue minerals. They almost completely failed in case of alkaline intrusive rocks as syenites, nepheline syenite, ijolites and pyroxenites, composed almost entirely of silicate minerals. A lot of effort was devoted all around the world on research of new, more efficient flotation processes. So in 1982, Les Services T.M.G. Inc. (Niobec), sole producer of pyrochlore concentrate in North America, developed the direct pyrochlore flotation process from carbonatites. In 1983, at about the same time, the Quebec Department of Natural Resources Laboratories and Les Services T.M.G. Inc. announced a successful recovery of niobium Minera1s from a low grade nenheline syenite ore."

Jan 1, 1984

By J. Paraszczak

High productivity of the equipment employed is one of the key factors in reducing production cost in mining. One of the best ways to achieve it is an increase in availability. In order to identify the most adverse factors affecting it, reliability and maintainability analysis ought to be done. If its results are to be conclusive, a sufficient amount of credible and consistent data is indispensable. Following the experience from field studies done in underground mines, this paper discusses the current status of failure and maintenance reporting, as well as problems encountered. It exposes the importance of adequate data collection on failures and downtime as well as it reviews the benefits of analysis based on such material. The question of benchmarking with regards to mining equipment performance is also addressed. The paper concludes with some recommendations on data collection and processing, as well as stresses the need to standardize the most important reliability/ maintenance notions throughout the mining industry and to conceive appropriate performance measures.

Jan 1, 2000

By J. C. Thornley

Service failures of seemingly conventional galvanized bolts, in normal operation, on transmission towers in New Brunswick have been found to be the result of hydrogen cracking. In both these cases, similar failures elsewhere can be avoided by suitable clauses in the purchase specifications. In the first case described, the manufacturing procedure was responsible for strengthening and embrittling a standard, soft, constructional steel. In this case, a fracture mechanics analysis predicted critical crack depths for final fracture very similar to those found in practice. This case reveals an apparent cooperative connection between hydrogen embrittlement and strain ageing in plain carbon steels. In the second case described, the steel was simply a high strength steel which should not have been made into galvanized bolts.

Jan 1, 1979

By Patrick Pelletier, Pierre-Alexandre Bossé, Julie Fournier, Gianni Bartolacci, Jayson Tessier, Ahmed Bouajila, Carl Duchesne

"This paper summarizes research into the study of the control of flotation processes based on froth images. The use of numerical image analysis techniques for the extraction of significant patterns (froth structure and colour) from industrial flotation froths is discussed.First, the froth was analysed by the use of the Multivariate Image Analysis (MIA) method to extract the spectral variation contained in a RBG image. The Partial Least Squares (PLS) was applied to develop the empirical model for the prediction of froth grade. The results of this application are illustrated using one industrial case study.Second, the froth was also analysed by Gray Level Co-occurrence Matrix (GLCM) and Wavelet Transform Analysis (WTA) to extract features related more to morphological aspects. Since there is useful information hidden in froth texture, these methods are used as texture descriptor to classify different types of froths.Third, a control strategy based on a froth structure indicator was developed and implemented on an industrial zinc flotation circuit. The feedback controller uses a reagent flow-rate in order to maintain the froth structure at its set point. Process improvements obtained with the implemented control strategy are highlighted.Finally, the feasibility to implement a hybrid control strategy consisting in a froth structure supervision controller based on the froth concentrate grade estimated by MIA and recovery inferred by image analysis is discussed.INTRODUCTIONThe development of control strategies to achieve satisfactory control performance has always been a great challenge for engineers and the need for improved process diagnosis, control and optimization has become more and more evident for the mineral processing industry in the last decades. That is why new process variables need to be measured particularly in highly multivariable processes such as flotation. This industrial process is subject to a wide variety of disturbances mainly generated by frequent and sometimes abrupt changes in physical and/or chemical ore characteristics and also, due to some irregularities in manual process operating procedures. A flotation circuit scheme is always a complex network of more than two dozens slurry streams. Information about those streams (% solid, metal content analysis and flow rates) is important for process diagnosis performance evaluation and control. Also, because of the grade decrease and increasing complexity of the new processed ores, more instrumentation outputs and more powerful and significant pr"

Jan 1, 2005

By Hans von Michaelis

"INTRODUCTIONThe renaissance in gold and silver recovery technology has continued to unfold and it is appropriate to review some of the useful new technologies as well as try to identify some of the industry's future needs and frontiers.The remarkable strengthening in the US dollar has resulted in a relatively low gold price in US Dollars of around $310/oz at the time of writing and silver at $6.25/oz. This general softening in the dollar prices and the recent confusion as to environmental compatibility of cyanidation tailings and effluents, has led to a slowdown in announcements of new operations. Another reason for the slackening off in the USA is that in the past few years a large part of the capital has come from oi I and gas companies that now seem to be losing interest in mineral ventures, and foreign investors for whom the dollar is becoming out of reach. In the author's opinion this represents an unprecedented window of opportunity.Elsewhere in the world where local currencies have weakened, the price of gold is at or close to its all time high.For example, in South African Rands, the gold price was R571.00/oz when the rand was US$1.47 and the gold price reached US$800. Now at US $309/oz and with the Rand at US$0.51 = Rl .00, the local gold price is R600. The price of si Iver in Mexican pesos is not much less than it was when silver reached US$50/oz. Gold, and silver prices in local currencies outside North America are still buovant and at levels where additional investment in new projects is more encouraging.Even in Canada where the dollar is worth about US$0. 75, this provides a smaller but significant cushion compared with US operations. Considering the present strength of the US dollar and even the Canadian dollar relative to many other gold producing countries, there should be significant investment opportunities at today's prices. Mining companies have started to descend on Brazil, for example, where in a matter of just a few years annual gold production has increased from 10 to 70 tons. In South Africa, a Canadian company backed by Swiss financing has been able to take over a Witwatersrand gold mining operation and is installing a huge new tailin9s retreatment plant to process about 1 million tons per month of tailings."

Jan 1, 1985