Search Documents

By N. Schmalbein, L. von Ketelhodt, L. Kotelo

"The mining industry continues to remain challenged. Lower commodity prices, increasing labor costs and more importantly diminishing reserves are amongst some of the primary factors contributing to the difficulties faced. Ore sorting technologies have demonstrated their potential to improve the downstream beneficiation performance. The general processing route sees all primary crushed material milled for liberation and then processed in accordance with characteristics of the gold therein, i.e.: refractory golds would require direct leaching or oxidation whilst free gold would follow the conventional cyanidation process, after gravity concentration. Ore dilution increases the associated operating costs within each stage of this process. The opportunity to process the same throughput at a higher grade can only be achieved through pre-concentration. Sensor based sorting has been examined on numerous occasions by various gold producers. Test work carried out on different bulk low grade gold ores has shown the successful applicability of ore sorting to remove waste, whilst maintaining high recovery rates of gold. The results of a combined XRT/Laser sensor sorter have shown grade improvements of over 300% from feed grades of 0,25g/t to 1,15g/t at gold recoveries of 66% and waste ejection rates of 85%. This paper presents some of the results from the work undertaken by STEINERT with respect to gold sulphide ore sorting and presents a modelled financial scenario, which can enable a company to target and reclaim low grade ores.INTRODUCTION The mining and minerals processing industry presents with many different challenges including, volatile commodity prices, increasing labor costs and more importantly diminishing reserves. Conventional processing routes will continue to play a crucial role in the beneficiation process, however innovative methods of reducing operating costs and optimizing on the overall circuit performance is where technologies such as sensor based sorting come into the fore. Sensor based sorting as a dry mechanical process not only reduces water consumption by eliminating unnecessary waste but also reduces the requirements for reagents in the downstream processes. Sensor based sorting under dry conditions presents a highly efficient alternative to wet pre-concentration methods such as dense medium separation (DMS)."

Jan 1, 2017

By L. Connolly, F. R. De Luca

"Rubber liners at Denison Mines Limited are used in 10 1/2x 24' low discharg0 pebble mills. These were originally 10 1/2 x 13 Dominion overflow type ball mills. Experience here shows that the wear of rubber and ni-hard lifters is approximately the same in the feed end half of the mill, while the wear of rubber lifters is much greater in the discharge half. The wear of rubber plates is considerably less than white iron in the feed end half of the Mill and slightly more in the discharge end half of the Mill. Rubber components are lighter to handle but their installation is time consuming. This leads to the conclusion that a combination of ni-hard lifters a~~ rubber plates is the most economical compromise in Denison's case, for the Mill. Rubber discharge grates are superior to steel grates, while steel feed end liners are superior to rubber.The Use of Rubber Mill Liners at Denison Mines LimitedGrinding is done in two identic0al circuits each consist-ing of one 10 1/2 x 14' Dominion overflow rod mill, two Dorr Oliver quadraplex rake type classifiers, two 10 1/2 x 24' Dominion low discharge grate pebble mills and ancillary pumps and conveyors for pebbles. There is one centrally located distributor box that receives the discharge of the 4 pebble mills and splits it out to the classifiers."

Jan 1, 1974

By C. Larsen, D. Fragomeni, A. Vien, D. G. Fisher

"MOCCA is a Multivariable Optimal Constrained Control Algorithm developed specifically for non-square industrial control applications with practical difficulties such as interactions, time delays, constraints, modelling errors, etc. MOCCA consists of an off-line simulation/translation module, for tuning the control parameters, and an on-line module that implements the designed control law.This paper describes an evaluation of MOCCA on the Hemlo grinding circuit which comprises one open circuit ball mill and two closed circuit ball mills in series. In this case a 4x4 unconstrained control problem was considered. The manipulated variables included the fresh ore feed rate and three pump box water additions. The controlled variables were the grinding circuit product particle size and three pump box levels. In this application soft constraints were implemented through control action and control error weighting. The feedforward capability of MOCCA was used to compensate for a measured water flow disturbance to one of the pump boxes. MOCCA performed very well during plant evaluations when compared to the original classical multi-loop control strategy and proved to be quite robust. Perhaps most importantly, the process engineers and plant operators have a high level of comfort both in understanding MOCCA's general operating principles, and with its demonstrated performance."

Jan 1, 1991

By A. Brown

IN INTRODUCING the subject of rock pressures, it may safely be assumed that mining men are only too familiar with the physical effects of strata stresses that accompany the extraction of minerals. It may be further assumed that they have, as individuals, arrived at certain conclusions regarding their nature, based upon years spent in observing such phenomena and in learning how to continue mining in spite of them. Such hardly won experience forms the core of what is often referred to as 'pit sense'. This essential type of knowledge is not ?based on theoretical considerations, nor can it be found in text books. It is highly individualistic in nature and almost impossible to pass on from one generation to another in terms of precise rules for guidance. It is this aspect of individual judgment based on practical experience that has led to the significant phrase The Art of Mining.

Jan 1, 1956

By H. L. Martin

A joint federal-provincial approach in gathering basic information from industry on mine production, concentrator operations and ore reserves, initiated during 1978, is a major step toward the goal of achieving better government-industry communication through a common data base. Information from questionnaires sent out by provincial governments is shared with the federal government; correct interpretation is ensured by mine visits conducted jointly by provincial and federal representatives. Initial focus is on nonferrous metal mines. The federal Department of Energy, Mines and Resources (EMR) is responsible for a national analysis that is aimed at the early detection of worrisome developments-and their reasons-in the flow from resources to reserves and from reserves to supply of these metals. The heart of the national analysis is the annual construction of a "monitoring curve", showing each metal's aggregated mine production as it would decrease over time if no new reserves and production capacity were to be added from the year of analysis. For a given metal, a comparison of monitoring curves from year to year can reveal early signs of supply stagnation. In anyone year, a monitoring curve in conjunction with foreseen needs for Canadian mine output will show the production gap that would have to be filled from reserves and production capacity yet to be developed. The production gaps for copper, nickel, zinc and lead, the four leading base metals mined in Canada, are shown for the 20-year period ahead, in the context of production achieved during the past 20 years. It is shown that reserve levels commensurate with likely future production levels would require that average annual reserve additions during 1978-98 exceed the average annual additions during the preceding 20 years. Reserve levels of all four metals have declined in recent years. A review of significant discoveries in the last five years suggests that this fall in reserves is not the result of a lack of exploration successes, but of stagnation in development for various economic reasons.

Jan 1, 1979

By R. W. Pugh, D. G. Bellow

"This paper will describe how cultivator shanks are made in one company and how the manufacturing was studied with a view to increasing product consistency and reducing manufacturing cost. The product: which is used extensively in the agriculture industry, was analyzed to determine which geometric parameters optimized its design and whether there was justification for the great variety of styles and shapes that are available in the market. Finally, an extensive series of field trials were undertaken which showed that it is advantageous to the manufacturer to be better aware of the loads and forces that his product is subjected to by another industry.IntroductionStelco maintains a Research Group for its Western Region operations headquartered in Edmonton, Alberta. Because of the small staff, a location that is isolated with respect to its Burlington, Ontario centre and a diverse set of processes and products, a university relationship has developed which may be different from that which would be developed at a larger integrated Steel Works. This paper outlines the type of cooperative studies carried out by Stelco Inc. in Edmonton and the University of Alberta. .To meet the research needs covering a wide variety of steelmaking processes and steel products produced in Edmonton would require more staff and equipment than the sales volume in the West justifies. The gap is filled by cooperation with university personnel. This cooperation has provided these benefits to Stelco Inc.:• access to specialized test equipment and a trained staff to operate it; and• assistance from experts in the areas of product testing and problem solving.Moreover, the close proximity of the university to the plant allows frequent meetings and ensures that practical solutions are developed and implemented. A good example of the ongoing university I industry relationship developed is the joint work on improving cultivator shanks."

Jan 1, 1982

By C. J. Farrow, M. J. Smith

"Bechtel has managed a number of test programs to establish autogenous grinding circuits and size mills for a variety of ores.This paper outlines the procedures whereby bench scale and pilot plant tests are used to select the most efficient circuit to grind the range of ore types likely in the mill feed.Five examples are given. One example traces the development of a pilot plant program; it shows how bench scale Work Indices provide a target for the grinding power requirement of an ore and relates how pilot circuits are changed as a result of interpreting the results from preceding tests. The other four examples relate the interpretation of the test results to provide design data; they illustrate a number of phenomena which have been observed.INTRODUCTIONConventional crushing and grinding circuits can be specified from bench scale test data such as Bond Work Indices. Bond Indices have been correlated to a large number of rod and ball mills and by applying appropriate factors, mills can be sized from the Work Index.For autogenous or semi-autogenous grinding circuits, bench scale tests are not sufficient to be able to specify the circuit and size of the mills for a commercial plant. It is necessary to run a series of pilot plant tests to determine how the ore behaves."

Jan 1, 1982

By C. M. Anson

Introduction The prosperity of any country today is dependent upon the efficiency and growth of its primary steel industry. The ?march of the United States of America to its present commanding position in world affairs parallels the growth of its steel industry. The remarkable growth of that industry was possible only because bountiful providence endowed that country with adequate supplies of the raw materials necessary for steel making -coal and iron ore. If we accept this hypothesis, and surely we must, then to what extent can we envisage the future of our own country? This symposium deals with the most important of the raw materials required for steel making -iron ore. If we are blessed with a bountiful supply of iron ore, then surely a glorious future awaits only our taking advantage of that blessing. It is becoming increasingly evident that Canada has immense iron ore deposits. It is my privilege to make you acquainted with one of these, one that can only be classified as among the more important ore reserves in the world. I refer to the Wabana ore deposits in Newfoundland. Location These deposits lie under the floor? of Conception bay, off the east coast of Newfoundland. They consist of a series of beds which outcropped for a distance of about three miles on the northeastern shore of Bell Island, dipping at approximately 8° toward the northwest. This three-mile outcrop is the only key to the occurrence.

Jan 1, 1951

By J. B. Mawdsley

Introduction The writer was instructed to visit the Chibougamau region during the field season of 1927 and report on the mineral discoveries that had been made there since 1911. lt was deemed advisable to obtain detailed information regarding the rocks underlying the area in the vicinity of these recent discoveries. Accordingly an area 60 square miles in extent was mapped. The outcrops were studied along the water courses and along bush traverses spaced at half-mile intervals between these water courses. The completion of the rest of the summer's programme allowed only three weeks for this work. lt is from this small, mapped area, and this necessarily cursory survey, that the material for this paper was obtained. Location And Means Of Access The name Chibougamau district is applied loosely to an ill-defined area of about 1,000 square miles lying mostly north and west of Chibougamau lake in the Province of Quebec. The lake is approximately half way between lake St. John and James bay. It lies 150 miles north of the Canadian National railway and 40 miles south of Mistassini?lake.

Jan 1, 1928

By L. W. Vigrass

Porous and permeable rocks deeply buried in sedimentary basins contain immense volumes of hot water with the potential to supply low-grade heat energy. A part of Canada with sizeable potential for low-grade geothermal energy is the northern Williston Basin of southern Saskatchewan. In this region, the University of Regina has conducted a geological study investigating the feasibility of producing large quantities of warm water suitable for space heating in the Regina - Moose Jaw area. The study has shown that the most favourable geothermal reservoirs are in the Basal Clastic Unit (Cambrian Ordovician), which, at an approximate depth of 2,000 metres has predicted temperatures of 71°C to 74°C. We anticipate sustainable flow rates from these reservoirs of 100 to 300 ms/hr. The water contains about 150,000ppm of total dissolved solids, mostly sodium chloride. It is anticipated that the sulphate content will be 3,000 to 6,000 ppm, that the dissolved oxygen and hydrogen sulphide content will be small, and that the waters will be neutral to slightly alkaline. It is anticipated that the piezometric level will be 46 m below the ground surface for reservoirs in the upper part of the Basal Clastic Unit and 141m below the ground surface for the lower reservoirs of the unit. Plans are to build a low-grade geothermal research, testing and demonstration facility at the University of Regina. To be a practical demonstration, the facility will have to handle very large volumes of water. Because of high salinity, the water will be re injected into a subsurface reservoir. We do not anticipate insurmountable problems because of salinities or as a result of corrosion provided that the waters are not aerated during handling

Jan 1, 1979

By T. Adamcewicz

The province's lignite resources lie mainly in the south, extensions of the much larger deposits in Montana and North Dakota. Because of planned additional capacity, conventional steam power generation will probably remain as the dominant resource usage for many decades. Conversion of coal to other energy forms is receiving emphasis and in the future will compete with steam power generation in terms of quantities used.Economic deposits, minable by present-day technology, have been generally defined. Because a large percentage of the total lignite resource is in seams containing multiple partings, future extraction will become much more difficult and capital intensive.Increased public involvement will ensure that the impacts of future coal mining and usage operations are compatible with environmental and social objectives.

Jan 1, 1982

By C. H. Knight

"THE OBSERVATIONS that follow are confined to simple wet cyclones such as the cylindro-conical unit developed by the Dutch States Mines and marketed in America under the trademark 'Dorr-Clone'. Energy to do the work comes from the inlet velocity of the feed slurry, which is usually pumped' to the unit by a centrifugal pump.Such cyclones are simply classifiers of enormous capacity and depend for their separating effect on differences in rates of particle settlement. These particle settling rates, of course, vary with particle size, particle density, particle shape, pulp viscosity, and pulp density.The dilution of the overflow product affects both pulp viscosity and pulp density. In most operations, the temperature and the composition of the liquid -hence its viscosity --are fixed, but both pulp viscosity and pulp density can be changed by changing pulp dilution.Since the separating effect depends on differences in rates of particle setting, a perfect split with 100 per cent of the particles coarser than a given size in the underflow and 100 per cent of the finer sizes in the overflow is not possible. Just how far the separation departs from this perfection can be calculated rather exactly from the following principles, which also apply to mechanical classifiers. In removing or settling out of the overflow product all particles up to a specified size, some of the finer particles must settle out simultaneously."

Jan 1, 1955

By P. Z. Caverhill

In this section of the province only the most meagre of surveys have been made and because these are not sufficient to determine with any degree of accuracy even the total forest area, the information presented in this paper is not complete. Area: -The area south of the Canadian National, and served by the Pacific Great Eastern, is roughly 38,000. square miles, 30,000 of which is classed as productive. This is approximately equal to the productive area of Norway, or half of Finland-or of 30 per cent of Sweden. It is larger than that of either Nova Scotia or New Brunswick. Eliminating from the productive area 3600 square miles of grass-land and areas capable of agricultural development, 26,000 square miles (16,600,000 acres) remains as absolute forest-land, as compared with the 55,000,000 acres of Sweden, the 37,500,000 acres of Finland, the 17,000,000 acres of Norway, and the 7,600,000 acres of Austria.

Jan 1, 1925

By A. R. Sorta, D. C. Sego

ABSTRACT Temperature, solute, texture, and thixotropic effects on time domain reflectometry (TDR) measurements of water content in oil sands tailings are investigated. Results indicate that TDR water content measurements are influenced by temperature, residual bitumen, and percent clay in the tailings. A correction of 0.03–0.10/ °C must be applied to the apparent dielectric constant (Ka) to account for the effect of temperature. The Ka-volumetric water content relationships of slurries differ significantly from the commonly used Topp calibration equation. The age of the tailings and the addition of phosphogypsum did not influence TDR water content measurements.

Jan 1, 2013

By E. W. Shaw

The past year (1950) has been a big one for the oil industry in Canada, with new records being set in almost every phase of exploration and development activity. New highs were reached in acreage holdings, in geophysical activity, in wildcat drilling, and in field development and production. The only item that did not show a substantial increase over recent years was the amount of reserves added by new discoveries. This was not due to a decrease in the number of new discoveries, however, hut rather to the fact that most of the discoveries were made during the later months in the year and could not be fully evaluated by the year end. The foregoing remarks pertain mainly to activity in Western Canada. In Eastern Canada, operations continued on a modest scale. with exploration drilling down slightly from the previous year but with development drilling and production at about the same level. Returning to Western Canada, it is observed that the general exploration play was one of expansion and intensification. The issuing of new petroleum and natural gas regulations by the province of British Columbia precipitated a moderate entry of companies into the northeastern part of the Province.

Jan 1, 1951

By E. Douglas, V. M. Malhotra

"This report presents the results of a laboratory study undertaken to evaluate ground granulated blast-furnace slag from Algoma Steel Corporation, as a replacement for Portland cement in cemented mine backfill. The evaluation was based on the results of compressive strength tests performed on cylinders cast from mixtures made with a granulated blast-furnace slag and tailings from four different mines in the Sudbury basin. Various percent¬ages of slags and various binder to tailings ratios were used.Tests results show that, in terms of compressive strength, the slag performs as well or better than Portland cement as the binding agent in cemented mine backfill. Lime was found to be a poten¬tially good activator for ground granulated slag in mine backfill applications.A field test was conducted at one of the mines, consisting of placing a mixture of 95.5% ground granulated slag and 0.5% lime into a stope, and inspecting the floor slab as it hardened. The slag performed as expected, considering the backfill mixture proportions used and the preparation of the test site."

Jan 1, 1989

By Charles T. Harper

The uranium deposits discovered by Amok (Canada) Ltd. in the Cluff Lake area of north western Saskatchewan occur at or near the southern edge of the uplifted basement core of the Carswell circular structure. Two types of mineralization, distinguishable, by their geological and structural setting and mineral paragenesis, have been recognized. The N-Claude type is characterized by a relatively simple mineral assemblage, consisting of uraninite or pitchblende with coffinite, and is accompanied by variable amounts of graphite and organic matter, and Fe, Cu, Pb and Mo sulphides. Both N and Claude orebodies occur within quartzofeldspathic gneisses of the basement core. On the other hand, the D-type ore has a complex mineral assemblage consisting of: uraninite, pitchblende, thucholite and coffinite, along with native gold and selenium; gold tellurides, and selenides of Pb, Bi, Ni and Co; sulphides of Fe, Cu and Pb; and organic matter. The D orebody occurs within carbonaceous shales at the base of the Athabasca Formation as well as in fault zones in regolithic quartzo feldspathic gneisses above the inverted unconformity. An age of 1050 m.y., which is consistent with a period (circa 1200-1000 m.y.) of widespread hydrothermal activity and uranium mineralization or reworking within and adjacent to the Athabasca Basin, has been obtained from uranium mineralization from the D orebody. Later reworking (circa470 m.y.) of the mineralization occurred at the intersection of older mineralized shear zones with radial faults produced during meteorite impact.

Jan 1, 1978

By P. E. Cavanagh

THIS REPORT is not intended to be a ?comprehensive survey of the steel industry in Europe. For the past ten years the Ontario Research Foundation has been interested in several developments in the steel industry in Europe which it was felt would be of particular interest in Canada and might possibly find application in this country. This is an account of the present status of some of these developments. The economies of steel making in Canada are somewhat different than in the United States because of the nature of the market and the relative costs and availability of such raw materials as metallurgical coke and electric power. There are cases in Europe where a great deal of effort and money has been spent in trying to make steel profitably by methods which take advantage of locally available and cheap raw materials by modifying standard practices. ln cases wl1ere the investigations have been successful and the data are available to allow translation of the results into Canadian conditions, it is felt that such information may be of great benefit in the future in Canada and at !east should be known to all those in the steel industry in this country. The field to be covered in this report only comprises the steps from concentration and treatment of iron ores to production of iron and is only concerned with those commercially operating processes well known to us and judged to be of present interest in Canada.

Jan 1, 1957

By L. Salnais

"Aluminum alloy structural components f or aircraft designed prior to the early 1970s, were machined from 2024, 7075 and 7079 plate, bar and forgings in either the T3xxx of the T6xxx tempers. Protective treatments for these parts consisted of chromic acid anodizing and alkyd zinc chromate primer, plus a nitrocellulose lacquer for exterior parts.The major service problem with these parts was the frequent occurrence of exfoliation corrosion and stress corrosion cracking (S. C. C.). Therefore, 2024 and 7079 alloys, with min or exceptions, were not used in aircraft designed after the early 1970s. Replacement materials were 7075 and 7050 alloys in the overaged, exfoliation corrosion and S. C. C. resistant, T73xxx tempers.The use of improved materials together with the upgrading to chromated epoxy primers, polyurethane enamels and the introduction of water displacing corrosion inhibiting compounds have significantly reduced corrosion in aircraft. IntroductionThe prevention of corrosion in aircraft has been a challenge to aircraft designers for many decades. With the design of the first all-metal aircraft, the designer and builder were thrust into the relatively new field of protective treatments as corrosion started to become more prevalent. This resulted from the continually increasing importance and wider utilization of aircraft, and their exposure to a wider variety of ho stile environments such as urban industrial pollution, high humidity tropical areas and salt ladened marine environments.Corrosion advanced another significant step when, after World War II, designs of new and larger aircraft utilized larger and thicker metal sections in the manufacture of structural components. With thicker mill products came higher residual heat treat, fabrication and assembly stresses resulting in an increased number of stress corrosion and exfoliation corrosion problems.Apart from the exterior environment, aircraft interior s can be exposed to a number of fluids which are either directly or indirectly responsible for corrosion. The most common of the fluids is water which is usually introduced as a result of condensation, especially in pressurized fuselages, and spillage from lavatories, galley s and electrolytes from batteries. These fluid s have a degrading effect on protective treatments and are also corrosive to the substrate metal. Fluids such as phosphate ester hydraulic fluids and ester based turbine engine lubricating oil s are not corrosive to the substrate metal, albeit they do contribute to corrosion by the degrading effect on protective treatments."

Jan 1, 1988

By O. Mejia, J. Drozdiak

"This paper summarizes a comprehensive energy and cost study comparing an existing SAG mill based circuit at Huckleberry Mine with two proposed circuits involving comminution technologies which are associated with energy efficiency: high pressure grinding rolls (HPGR) and high speed stirred mills. The specific energy requirements expressed as kWh/t for the proposed circuits were determined from pilotscale HPGR and stirred mill testing conducted at the University of British Columbia. Samples and operating data were collected from Huckleberry’s copper-molybdenum concentrator to evaluate current mill performance for comparison. To support the base case, the SABC circuit was modeled using JK SimMet® software. The main comparison focused on the complete energy requirements for each circuit, including materials handling equipment such as conveyors, screens, feeders and pumps. This paper also provides capital and operating cost estimates for each of the comminution circuits. The results showed that the HPGR - ball mill circuit achieved a 21% reduction in energy consumption over the existing SAG - ball mill circuit at the same P80 grind size of 160 µm. At a grind of 80% passing 75 µm, the HPGR - stirred mill circuit showed a 34% reduction in energy compared to the base case. It was concluded that the energy reduction for the new flowsheets significantly improved the economics of the Huckleberry comminution duty.INTRODUCTIONUp until now, tumbling mills such as AG/SAG mills and ball mills have had a dominant bearing on the design and economics of comminution circuits. However, it is commonly agreed that the majority of employed comminution processes are energy intensive and energy inefficient, accounting for up to 80% of overall process plant energy consumption and having an efficiency of as low as 1% (Abouzeid and Fuerstenau, 2009; Fuerstenau and Abouzeid, 2002). The U.S. department of energy reported that there is a potential to reduce energy consumption in the metals industry by up to 61% from current practice to bestestimated practical minimum energy consumption; suggestions included the implementation of best practices and the adoption of energy efficient mining and mineral processing technologies such as advanced blasting techniques, high pressure grinding rolls (HPGR) and stirred mills (U.S. DOE, 2007)."

Jan 1, 2013