Search Documents

To optimise the haulage of the large tonnages produced from stopes in this high production gold mine, an ore pass and feeder system was introduced. This ore pass was designed and developed in 2006 and the plate feeder installed and commissioned soon after. Cavity Monitoring Surveys (CMS) have been undertaken of the ore pass since it was commissioned. The original thickness that was surveyed of the pillar between the ore pass and decline in 2006 was approximated to be 19 m. Throughout its use large blocks of rock were reporting at the plate feeder. This was the first indication that the ore pass was failing somewhere between the tipping level of the 9410 level and the plate feeder at the 9330. Even so CMS surveys were not taken systematically to firstly identify the area of failure or for monitoring. In August 2008 after implementing management systems, large blocks were still reporting to the plate feeder. The decision was made to empty the pass enough to carry out a CMS survey of the area. Subsequently it was discovered that the area of failure was between the decline and ore pass and that since the first survey the pillar thickness had been reduced to approximately 9.7 m. Further management controls were put in place to slow movement of the material and to limit the use of the 9410 tipping level, but this did not alleviate the rate of failure entirely. The results of an initial inelastic numerical model indicated that most of the pillar was damaged and that failure into the decline likely if no changes were made. The numerical modelling predicted that even if material was no longer passing through the ore pass interaction between the voids was unavoidable and would most likely result in instability. The ore pass and plate feeder are an integral part of the haulage system for the remaining life-of-mnie. Two solutions were sought to firstly reinforce and stabilise the pillar between the ore pass and decline and secondly to rehabilitate the ore pass or find an alternate design that could still utilise the plate feeder. This paper summarises the analysis and resulting rehabilitation that was used to accomplish this.

Nov 25, 2010

This paper describes the economic study of longwall versus bord and pillar mining using all continuous miners for a colliery located at the South Coast district of New South Wales, Australia. In this district longwall mining appears to be a better economic proposition than bord and pillar. The internal rate of return on investment is found to remain approximately constant for each method irrespective of life. The economic importance of percentage extraction of coal is shown to be small for high values of minimum rates of return, becoming more significant as the minimum rate of return decreases.

Jan 1, 1980

The commonly used Stopes-Heerlen coal petrographic classification and nomenclature has over the years been subject to variable interpretations. This paper discusses the problem with specific reference to the inertinite maceral group. The effect of various interpretations of the Stopes-Heerlen system on maceral analysis is discussed and illustrated by means of comparative analyses conducted by a number of laboratories in Australia.An attempt is made to define the reflectance thresholds used by the authors to subdivide the inertinite group; the genetic and technological significance of these thresholds are compared.The difficulties of distinguishing structured and nonstructured macerals of the inertinite group are discussed in terms of possible improvements to the present StopesHeerlen system by extending the classification to include transitional maceral types.

Jan 1, 1970

Radioisotope x-ray and neutron techniques of analysis can be used for the determination of a wide range of elements in minerals. The most important applications of these techniques to the mineral industry are for onstream analysis of slurries and solids, and for geological assay.The radioisotope x-ray techniques are the more developed ones and two installations for on-stream analysis are in routine use in mineral processing plants in Australia. Neutron techniques are being developed, and should prove valuable for geological assay of large numbers of mineral samples, for borehole logging, and for specific on-stream analysis when the cost of the equipment is warranted.

Jan 1, 1970

Authors have been conducting research on autonomous loading operation by wheel loader. Autonomous loading cycles has been demonstrated with real size experimental model. In V shape loading operation, travelling between scooping point and dumping point is dominant factor for cycle time of the operation. The positions of scooping point and dumping point changes with advancing the operation. In the developed system, path planning is performed at the beginning of every cycle. The path is formed by combination of curve and straight path elements. During travelling on the planned path, path following control is applied on the loader to keep position error in narrow range. Positioning of the loader is based on dead reckoning with correction by global positioning system (GPS) data. In a process of path following control, control value for steering angle is determined based on position error in lateral direction. Proposed method of path planning and position control is installed and tested in the real size experimental model. The detail and results will be described in the paper.

Dec 6, 2010

The importance of timbering, not only from a financial point of view but from an actual mining point of view, is so often overlooked or slightly glossed over by the average expert and investor, that I have thought it would prove interesting to go into the matter and to invite discussion upon the subject. We will first take small veins, or reefs as they are termed in some mining countries; and by small veins it is intended to denote fissures from a few inches to three feet. The ore body is supposed to be confined within well defined walls free from gangue matter, unless the casing can be defined as such. Now, if the walls are smooth and moderately hard, no timbering is required other than the stulls, which are braced from wall to wall in order to form platforms or stages to stope from. Should the reef from wall to wall prove payable, or should the vein be of a character to prohibit cleaning or sorting; and it be determined to send the whole of the stone to the, reduction works, the stuUs should be left in place until the section or block of ground is worked out, in order that if a weak spot in the walls (especially the hanging) occur, it would be possible, without any particularly extra expense or difficulty often times accompanied by danger to brace and secure the slabs. After the block became entirely stoped, it would pay where labour was cheap to remove the majority of timbers to stull another section.

Jan 1, 1901

By Wittenberg J. C, Reid A. F

A method is described for the rapid and effective production of polished section mounts of ore and mineral particulates to the standards required for automated image analysis. This requires mounting without segregation of particles by mass or density, and it is also preferable to avoid having particles in contact so that they can be recognised as individuals. To achieve this, the particle samples are first split to an appropriate degree in a rotary riffle, and the sub-sample mechanically diluted and thoroughly mixed with an inert filler of the same size range as the particles. Just sufficient epoxy resin is added to make the mixture fluid. During setting, the ore particles are mechanically supported by the inert filler particles, thus maintaining the particles in a random three-dimensional distribution. A rapid two-stage grinding process, based on the successive use of 600 mesh silicon carbide and 1200 mesh (10 um) corundum on cast iron plates, is followed by three stages of mechanical diamond polishing on cloth laps. Hand polishing is entirely avoided, as is the use of papers.

Jan 1, 1984

Owing to the increased consumption of sulphuric acid; Australian manufacturers have, from time to time, been seeking for a satisfactory source of sulphur that would make them independent of foreign supplies.Some years ago a considerable amount of acid was obtained from the roasting of Spanish pyrites. This ore, in 1913 or thereabouts, cost 16s. per ton f.o.b. Huelva, and freight to the eastern seaboard of Australia was about 20s. per ton. As the ore contained 48% to 50% of available sulphur, it was costing roughly 9d. or 10d. per unit, and, in addition, the cinder, after roasting, was a product of considerable value to smelters, containing as it did a high percentage of iron suitable for fluxing, and appreciable values in silver and gold.

Jan 1, 1925

With the exhaustion of orebodies close to the main haulage shaft of the Emperor mine, an increased rate of development, aimed at earlier investigation of values disclosed by exploration drill holes has been attained with an overall reduction in unit costs.This paper describes the techniques used in rates of advance up to and exceeding 1,000 ft per 28-day period.

Jan 1, 1966

By W Polkowski, M Tangstad, M Wallin, J Jiao

Fe-26Si-9B (wt per cent) alloy has been identified as a potential high-temperature phase change material (PCM) due to its attractive properties, such as its high latent heat of fusion and low volumetric change during solid/liquid transition. For the successful utilisation of this alloy into thermal energy storage (TES) systems, the development of a cost-effective production method is essential. Presently, the Fe-26Si-9B alloy is produced by mixing FeSi alloys with either pure boron element or FeB alloys. However, the use of pure boron is financially prohibitive, and the carbothermic reduction results in high greenhouse gas emissions and high energy consumption in the production of FeB alloys. In this regard, our study proposes a silicothermic reduction method to produce Fe-26Si-9B PCM by using FeSi alloys and B2O3-based oxides. Accordingly, the influence of various parameters on the production process was investigated, including operating temperature, holding time, B2O3 content in the added oxides, and initial Slag/Metal (S/M) ratio. Based on the experimental results, the optimal parameters for producing FeSiB alloys with over 9 wt per cent boron were determined. Consequently, it was documented that the FeSi alloys and the added oxides enriched with 50– 65 wt per cent B2O3 should be subjected to temperatures ranging from 1550–1650°C, maintain an initial S/M ratio exceeding 1, and ensure a holding duration beyond 1 hr. Moreover, the energy consumption of this process was estimated to be ~1.86 MWh/t metal and the mass loss was lower than 7 per cent. Therefore, silicothermic reduction offers a sustainable approach for producing FeSiB alloys with a boron content above 9 wt per cent.

Jun 19, 2024

A laboratory size solvent extraction apparatus has been constructed, which incorp- orates three stages of countercurrent extraction, followed by two stages of counter- current stripping. The model uses a gravity flow system from one stage to another and air lift pumps to recirculate organic and aqueous phases. A novel pump/mixer system is used to transfer solutions from the mixer compartments to the settler compartments. The model has proven valuable in the teaching of solvent extraction principles.

Jan 1, 1999

The process of electrostatic separation was developed in the late 19th century, but did not make much headway for about 25 years. High dc voltages, of the order of 20 kilovolts, are involved, and the only means of obtaining such voltages at that time were by the use of frictional machines, such as the Wimshurst. These were not reliable, for two reasons:-a. If a spark discharge occurred it took an appreciable time before a steady voltage was again attained.b. In damp weather the machines were almost useless.In the first 20 years of the 20th century the advent of mechanical and vacuum-tube rectifiers led to promising developments of 'the process. In the early 1920's flotation became widely used commercially, and proved to be more reliable, and capable of wider application, than electrostatic separation. During the last 15 years or so, with a better knowledge of the fundamentals forming the basis of the process, electrostatic separation is beginning to compete with flotation, especially in the treatment of smallsizedgranular material, such as beach sands. Electrostatic separation can be, and is, widely used in many cases where flotation is impossible, such as in the cleaning of food products which must be kept dry.

Jan 1, 1950

Particle Size Measurement of TiO2 Nanoparticles in Non-Aqueous Solvent by Interactive Force Apparatus Under an Electric Field

Sep 13, 2010

Although the Diamond that is cut and polished and made up into an article of jewellery, is so well known, there are, comparatively speaking, very few outside the industry who know this beautiful crystal in the crude state, as turned out ofNature's laboratory, and the means employed in winning this precious stone.This article is written with the endeavour to give the reader some idea of the geological formations in which the Diamond occurs, and as it is reported that Diamonds have been found in Western Australia, as well as in other parts of the Australian Colonies, a few hints as to the means employed in working the ground in South Africa may be of use to those intending to prqsecute the search in this country. The general geological formation of the South African Diamond Fields is Lacustrine shales and sandstones, intersected by dykes of various eruptive rocks, varying considerably in their character. and in places vesicular in texture, the vesicules being more or less filled in with zeolites by permeating waters.

Magnetic anomalies in the Southern Coalfields have been subdivided into two characteristic types. Each type is attributed to a separate cause, one being basement structure, and the other near-surface igneous intrusions.Detailed geological mapping of the area and the ability to sample throughout the coalmines greatly assisted in this subdivision.The Triassic sequence contributes no magnetic effect of its own except to diminish the effect of sources within the underlying formations by raising the level of observation.Detecting the presence of igneous intrusions ahead of colliery working faces by magnetic observations within the coal mines may be of value in preventing accidents caused by gas outbursts and in planning the workings so as to avoid loss of production time.

Jan 1, 1967

Effects of DA as a Grinding Aid on Selective Grinding of Low-Grade Bauxite Effects of DA (a copolymer of acrylic acid and acrylamide) as a grinding aid on selective grinding of low-grade bauxite were investigated in this study. The addition of DA into the grinding system enhanced the selectivity of grinding and increased the A/S ratio in the coarse fraction of ground product, leading to improved throughput of grinding mills and alumina recovery. The results showed that DA decreased the viscosity of slurry significantly and hence improved grinding efficiency due to low viscosity at a high slurry concentration. Both the hydrogen bond formation and chemical adsorption existed between DA and the surface of bauxite particles. The adsorption of DA on the surface of bauxite could decrease stress needed for crack initiation and extending during grinding, prevent new-born crack surfaces from rejoining, and promote the expansion of the cracks.

Sep 13, 2010

The paper examines the value of very small-scale indigenous gold mining operations to developing countries. The paper looks particularly at this type of activity in two neighbouring countries, Papua New Guinea and the Philippines, considering technical, economic, social and environmental aspects.

Jan 1, 1990

By W Dodson, S Dogramaci

Isotopes and hydrochemistry were used to define groundwater flow systems and better understand the hydrogeological setting of the Karijini National Park, which is in the Central Pilbara region adjacent to the Marandoo iron ore mine. Based on the stable isotope composition of the water samples, the data can be divided into two main groups. Groundwater is characterised by depleted dD and d18O, suggesting no significant evaporation effect. Surface water on the other hand is more enriched in dD and d18O due to evaporation. The relatively high concentration of Cl- compared to rainfall and depleted dD and d18O values of groundwater indicate that recharge of the aquifers is occurring during intense rainfall events when rapid infiltration occurs. Evapotranspiration then acts to concentrate ionic species prior to recharge. Relationships between the major ion concentration and catchment area, surficial Tertiary cover and distance between recharge and discharge were identified. The results show that these catchment variables combine to determine unique water chemistry for each sub catchment in Karijini National Park. The TDS concentration of the groundwater in the Marra Mamba Iron Formation that hosts the Marandoo ore body is higher than most of the water bodies surrounding the mining area suggesting significant modification or different recharge mechanisms to that of the Karijini groundwater.

Jan 1, 2009

ALTHOUGH it has been a matter of about one hundred years since the idea of the internal-combustion engine entered the mind of the inventor, the practical application of its use was not attained till 1860, when Lenoir produced an engine similar to the ordinary highpressure steam engine, with the valves arranged to admit the explosive mixture and the discharge of the exhaust gases. In this case no attempt was made to compress the gas before ignition, as it was then considered that the explosion under these conditions had a detrimental effect, inasmuch as it would act as a sudden blow to the working parts. Indeed, he went so far as to inject steam and water sprays to reduce the explosion.Under these conditions the consumption of gas was exceedingly high-about 106 cub. ft. of coal gas per b.h.p. per hour but the mechanical effect showed that the engine ran in every respect as smoothly and quietly as in best steam-engine practice.The extravagant consumption of this engine was clearly pointed out at the time by Gustav Schmidt in a paper before the German Society of Engineers, wherein he states :-" The results would be far more favourable if compression pumps, worked from the engine, compressed the cold air and cold gas to three atmospheres before entrance into the cylinder. By this means a greater expansion and transformation of heat is possible."

Jan 1, 1912

ALTHOUGH great progress has been made in flotation of the Broken Hill silver-lead-zinc ores, no paper dealing with this subject has been presented to the members of the Institute since James Hebbard's valuable contribution in 1913. Almost every discovery or development in the history of flotation has formed the basis 6f a patent, and but few experimentalists have overlooked the fact that their investigations might lead to the establishment of a patentable process. This, together with the aftermath of patent litigation, naturally resulted in secrecy being maintained in matters appertaining to the art, and the industry as a whole has consequently suffered considerably. Much valuable time has been wasted through numbers ofmen repeating work along certain lines, which, unknown to them, had already been thoroughly exhausted by others, whereas a lot of this would have been avoided by a freer interchange of information amongst those directly concerned. Owing to differences in the ore treated and the various applications of flotation concentration in relation to gravity methods, the flotation problems of the various mines differ considerably. This, together with the secrecy previously referred to, hasresulted in the development of numerous systems and machines, most of which would appear, to the casual observer, to comprise separate and distinct processes. The author has endeavoured to show how much these processes have in common with one another, and, at the same time, has tried to convey some general ideas on flotation to those members of the Institute who are not directly associated with this branch of concentration.

Jan 1, 1919