Search Documents

By K L. Temel, W P. Player

The underlying message of this paper is that investment in prospecting, exploration and mining in New Zealand is welcomed. The Government's policy with respect to Crown owned minerals is for continuing investment in prospecting, exploration and mining which is in accordance with good exploration or mining practice. To encourage continued investment requires a business-friendly environment. Government policies and initiatives to enhance the business environment for the minerals and coal exploration and mining industries are discussed in this paper. As well, new initiatives under consideration, which have the purpose of enhancing the investment environment, are discussed.

Jan 1, 1997

By A. J. MOORE

When the writer first saw the square-set timbering, he was at once impressed with the fact that the frames made by the sets, along the lode and across it, were composed of panels with rectangular openings, and it was puzzling to understand howsuch a collapsible construction could resist pressure that came unevenly on it. Later he learnt that the sets did not satisfactorily resist such pressure, but mullock filling had, to a great extent, to undertake this duty for them. So it appeared that the setswere practically an expensive scaffolding, enabling the miners to work in the face and carry the stope forward, till the filling was put in behind them to take the pressure of the roof and sides of the excavation. Of course some of the pressure is takenby the sets, but this is because "the set timbers prevent the filling being done perfectly; if it were practicable to remove the sets before filling, the filling by itself would more effectively support the back and wall, than do the combined sets andmullock. On the whole, therefore, the sets can hardly be said to be of much benefit where pressure has to be resisted. Despite this, the system has been of immense service in mining wide lodes, but for all that, it can only be pronounced a makeshift.This is no reflection on Deidesheimer, the famous originator of the square set, for, as will be shown later on, this way of...

Jan 1, 1912

The success of smooth blasting essentially depends on geological condition of rock. Also, in the perimeter hole, borehole pressures with light, well-distributed explosive loads are important to minimise overbreak. In order to simulate perimeter holes with scaled model test, the borehole pressure was considered as a factor of scale. Hydraulic oil pressure is applied as borehole pressure instead of using explosives and detonators in order to remove the undesirable effects of detonators in an experimental set-up of just two perimeter holes in a tunnel blast. The borehole pressure on a perimeter hole is nearly reproduced with hydraulic pressure which is generated by non-electric detonators in the hermetical cylinder.

Dec 6, 2010

As the theme of this conference is æRediscover OtagoÆ it would seem appropriate to revisit the era of the gold rushes and subsequent mining industry which rapidly advanced settlement and economic prosperity for Otago, and left permanent reminders in the form of historic mining sites, many of which are now encompassed within the Otago Goldfields Park. I have been invited to give a paper at this conference on the subject of æHistoric Goldfields of Central OtagoÆ. As well as having a working involvement with historic areas through my employment with the Department of Conservation, I have a personal interest in the early goldmining industry of Central Otago as my grandfather came out from Scotland in the 1890s to help construct gold dredges on the Molyneux. My grandfather made headlines in the local paper in 1920 when he believed he saw a New Zealand otter at Island Block near Beaumont - but that's another conservation trail that I will not pursue any further today! For this paper I intend to divide my time to cover the following topics. Firstly, I would like to sketch a mental picture of the characteristics that make up the Central Otago landscape, and the general perception that early miners must have had when viewing this foreign land. Then I would like to briefly discuss the changes and the consequences in the early gold rush to Central. Finally, I would like+ to discuss the establishment of the Otago Goldfields Park, which I will illustrate with several slides.

Jan 1, 1992

By D Kotzen

Online cyanide analysers have been successfully used to control free cyanide in the gold/silver leach process for over 15 years. Use of such analysers leads to cyanide savings and improvement in recoveries. Plants with leach cyanide analysers show both lower and more consistent cyanide levels in tailings. Cyanide code compliance requires meeting residual cyanide targets in tailings. Monitoring and logging of the residual cyanide in plant tailings and effluent is required. Meeting targets may require cyanide recovery/destruction processes to be implemented. The operating cost of destroying cyanide is often the same order of magnitude as the cyanidation cost. Various cyanide destruction and/or recovery processes are reviewed. Choice of a process consistent with the environmental and operational requirements is illustrated. Online weak acid dissociable cyanide (CNWAD) analysers have recently been developed and introduced on gold plants. The application of a WAD 1000 online CNWAD analyser at a large gold plant is presented. The analyser ensures code compliance, reduces cyanide destruction process operating costs and forms a historical record of CNWAD values in tailings.

Jan 1, 2007

By Met M. E, Worner H. K

During the past two years, a large number of creep tests has been carried out on electrolytic lead, special assay lead and ordinary refined (Port Pirie) lead. Some of these tests have already been reported.1§ In addition, an attempt has been made to estimate the influence of the individual elements present in small traces in Port Pirie lead. The present paper gives the results obtained when small additions are made to "U" lead of the composition shown in Table 1.(which has been used throughout these investigations during the past few years). The additions were silver, antimony, bismuth and zinc. The results of the addition of tellurium have already been communicated. This investigation was intended to run parallel with a similar one using electrolytic lead as a basis and adding one element at a time.Actually, the experiments using "U" lead have got rather ahead of the others. The important point has emerged, however, that the effect of a .given addition may be appreciably influenced by the presence of traces of other elements.In most of these tests, an initial stress of 500lb. per sq. in. has been used. Whilst it is fully appreciated that this stress is higher than those used in practice, it has to be borne in mind that an improvement in creep resistance was *Manuscript received December 11th, 1936.

Jan 1, 1936

By Z S Chang, T F. Zhou, G X. Zhong

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The Yaojialing zinc-gold polymetallic deposit is a newly discovered, large skarn deposit in the Middle-Lower Yangtze metallogenic belt, East China. It is located in the transitional zone between the Tongling uplift block and the Fanchang faulted basin. It is mainly hosted in the contact zone between early Cretaceous granodiorite porphyry and Carboniferous-Triassic limestone, or occurs in limestone xenoliths within the intrusion. Skarn and stratabound massive sulfide orebodies are the primary ore styles. Sulfide ?34SV-CDT values indicate a magmatic sulfur source, in common with most deposits in the Tongling block. Calcite d13CV-PDB and d18OV-SMOW ratios reveal that marine carbonates were the major source of carbon in late-stage hydrothermal fluids. The calcite probably formed during interaction between magmatic fluids and carbonate wall rock.CITATION:Zhong, G X, Zhou, T F and Chang, Z S, 2015. Geology, chronology and isotope geochemistry of the Yaojialing zinc-gold deposit, Tongling ore district, Anhui Province, China, in Proceedings PACRIM 2015 Congress, pp 457–462 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By A Hekmat, M Fuentes, F Armijo, R Castro, F Rodriguez

Interpreting the behaviour of granular material and simulating the gravity flow are complex processes in cave mining methods. In this paper, a new Cellular Automata based code – FlowSim – is used as a flexible tool to simulate the gravity flow and subsidence zone in block caving mines. The simulation results of the gravity flow model in a real scaled mine as well as a scaled physical model are presented in this study. In this research, FlowSim was first calibrated at a mine, based on the information obtained from smart markers. These markers were located in five points of the second block of the Esmeralda sector, at the El Teniente copper mine, Codelco, Chile. The calibration was performed with the objective of reducing the discrepancy between the extraction zone defined by markers in the mine and FlowSim outputs. Regarding the mine data, FlowSim was calibrated with the minimum error of ten per cent between real and simulated results. Then, the calibrated FlowSim model was used to simulate the flow behaviour of a scaled physical model. This model was constructed in the Block Caving Laboratory of the University of Chile to scale down the same block of the Esmeralda sector with the scale of 1:200. The FlowSim outputs show that this software enables the simulation of the gravity flow of the scaled model with less than five per cent discrepancy in grade and dilution entry to the drawpoints. According to the obtained results, this paper recommends FlowSim as an appropriate tool which can improve the design of production level in block caving and can enhance the prediction of the subsidence zone and dilution entry.CITATION:Castro, R, Hekmat, A, Fuentes, M, Armijo, F and Rodriguez, F, 2016. FlowSim – a versatile flow simulation tool to quantify extraction and design alternatives for block caving, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 645–652 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By D Hill

In the Ngakuru area zeolite deposits occur in late Quaternary lacustrine vitric tuffs of the Ngakuru Formation and two of the deposits are being mined. The Ngakuru Formation overlies the Ohakuri Ignimbrite dated at c. 240 ka, and is overlain by younger alluvial sands and gravels. Individual zeolite deposits contain 50 - 80 per cent zeolite over a thickness of up to 45 m in thinly stratified vitric tuffs and are localised along NE-trending normal faults. Glass shards in the tuffs are replaced by the silica-rich zeolites mordenite and clinoptilolite. Amorphous silica (opal A), opal-CT, Kfeldspar and smectite are also present. The zeolites and other minerals are very fine grained (<10 8m), with open meshes of crystals that result in high porosities (52 - 70 per cent) in mordenite-rich tuffs. Zeolitic tuff samples typically have cation exchange capacities of 80 to 110 meq/100 g and internal surface areas of 25 - 58 m2/g, which combine to give high liquid and odour absorption capacities. The first zeolite deposit (Mangatete) was found in 1992, and this and the Twist Road deposit are worked by quarry benching into the side of hills. The zeolitic tuffs are dried and crushed to produce a variety of products including adsorbents for soaking up oil/chemical spills and animal wastes, animal feed supplements, water treatment, and sports turf and slow release fertiliser. The Ngakuru zeolite deposits formed at shallow depth (<100 m) along fault zones from reaction of glass-rich tuff beds with groundwater-diluted geothermal water during the late Quaternary, and are as young as 8500 yr BP from 14C dating of plant material in sinter associated with the Mangatete deposit.

Jan 1, 2005

High Pressure Sulfuric Acid/Oxygen Leaching of Platinum Group Metals Bearing Ni-Cu Mattes The processing of platinum bearing Ni-Cu ores for the extraction of platinum group metals (PGMs) involves comminution, flotation, smelting, and converter treatment of the furnace matte. Leaching circuits are predominantly used for further processing to separate the base metals and PGMs contained in the converter matte. Nickel dissolution is primarily achieved in the first stage leach (high pressure or atmospheric leaching, or a combination of the two), which is followed by second stage high pressure sulphuric acid/oxygen leaching to dissolve copper and the remaining nickel. PGMs are recovered from the leaching residue in downstream processes, and their dissolution in the first two leaching stages must hence be limited. Studies have been conducted to investigate the leaching mechanisms and kinetics of base metals in different leaching environments. The key operating parameters that influence the leaching kinetics of these metals include the temperature, acid concentration, degree of agitation, feed particle size distribution, and oxygen partial pressure. There is, however, a limited understanding of the behaviour of PGMs in the high pressure leaching process. Consequently, this process is controlled based on operators' intuition despite its importance in the recovery of PGMs. An improved fundamental understanding of the behaviour of PGMs in this leaching environment is required to be able to accurately model the process. This in turn will allow the development of an improved control strategy and the estimation of optimum operating conditions. An overview of the leaching mechanisms of base metals and the effects of key operating parameters on their dissolution kinetics in different leaching environments are presented. Models that have been developed to predict the leaching behaviour of base metals are discussed and evaluated. Finally, initial results obtained with an experimental setup that will be used to investigate the behaviour of PGMs in high pressure leaching systems are discussed and compared with published results.

Sep 13, 2010

This paper gives a general description of mining operations at the Mount Morgan Open Cut. Certain features such as blast hole diamond drilling, which may be of particular interest, have been described in detail. The paper is covered by the following headings:-1. History2. Ore Reserves and Production Data3. Mining Methodsa. Design and Layout of the Open Cut.b. Overburden and Ore Breaking.c. Loading and Transport of Ore and Overburden.d. Transport of Men and Supplies.e. Survey and Assay.f. Drainage.4. Power and Compressed Air5. Mining Equipmenta. Shovels.b. Mine Transport.c. Dozer Tractors.d. Drill Shop.6. CostsHISTORYIn order to appreciate fully the design of the present Open Cut at Mount Morgan, a brief outline of the Mine's history and past mining methods is necessary. In 1882 the Mount Morgan Syndicate began to mine this large gold-copper orebody by small hill-top quarries...

Jan 1, 1952

To date Iron Monarch is the most important Australian source of iron ore and since HH5 has produced about 84 million tons of direct shipping ore containing 62 per cent iron and 3 per cent manganese.Previous geological work, mainly by Rudd, Edwards and Miles is reviewed and the results of later exploration by quarrying and drilling are discussed and modified interpretations of both stratigraphy and structure are advanced. Renewed study of the mineralogy of the iron ores is advocated.The Iron Monarch orebody lies on the up-thrown side of a major transcurrent fault that truncates it on its northern boundary. The nearby Iron Knob orebody is believed to occupy a horizon that is some thousand feet stratigraphically above Iron Monarch.The origin of the ore cannot be explained by any simple theory; development probably took place over a long period of time from Lower Palaeozoic to Tertiary.INTRODUCTIONIron Monarch orebody has supplied the Australian iron and steel industry with the greater part of its ironstone requirements since the establishment of the Newcastle steelworks in 1915. Annual production of direct-shipping ore has exceeded three million tons but declined slightly after 1956 when Iron Prince was brought into production. Total production of ore from Iron Monarch to the end of 1962 is about 84,000,000 long tons containing some 55,000,000 tons of metal.The deposit (Lat. 32°44'30"S : Long. 137°08'30"E) is 34 miles north-west of Whyalla, on the western shore of Spencer Gulf. A 42 in. gauge railway connects Iron Monarch and its associated small town of Iron Knob with Whyalla (Fig. 1).For the purpose of this paper Iron Monarch includes Iron Knob and the intervening jaspilite hill known as Substation Ridge, and the description of the general geology necessarily 'Assistant Chief Geologist, The Broken Hill Proprietary Co. Ltd.This paper was presented at the Annual Conference of The Institute, 14-24th August 1968.

Jan 1, 1964

By P E. H Gregg, D Horne, R B. Stewart, N Bolan

The Tui mine site is situated on the NW flank of Mt. Te Aroha, at approximately 400 m altitude. During underground mining operations two lead-copper-zinc ore bodies were exploited and processed on site. The legacy of the mining operation is a barren dam containing over 100 000 mm of sulphide-rich tailings. The Tui mine site is arguably the worst case of environmental degradation resulting from past mining activity inNew Zealand. Although the impacted area (approximately 4 ha) is extremely small by international standards, acid mine drainage (AMD) emanating from the abandoned tailings dam and mine adits has severely contaminated local streams and prevented natural plant recolonisation of the site for more than 20 years.   The suitability of the tailings as a potential plant growth medium was assessed with the end view of revegetating the tailings dam and alleviating AMD. This paper outlines characterisation work conducted on the tailings and summarises preliminary results from plant growth trials. The tailings contain up to 5% Fe, 1.15 % Pb, and 0.45% Cu in the form of sulphide minerals. The distribution of heavy metals, sulphate and total sulphur with depth indicates that the top 200 - 300 mm of the tailings have been extensively weathered since their deposition. The oxidation of sulphide minerals, particularly pyrite (FeS2 ) has reduced the pH of the tailings to nearly 2 in places. Below 300 mm the sulphide minerals are largely unweathered and the theoretical acid generating potential of the tailings exceeds 170 Mg CaCO3/1000 Mg tailings at certain depths. Plant growth trials were conducted to study the effects of lime and organic matter addition on the establishment of vegetation on the Tui mine tailings. Several plant species were assessed including some cultivars bred for their tolerance of heavy metals.

Jan 1, 1995

By Peddie F, Low K, Madgwick J, Rajoka M. I, Gutierrez N, Lim C

Percolation irrigation of low-grade quartz feldspar porphyry ore with pH 2.0 H2SO4 at 510 litres/m2/day using particle sizes 1.7 - 6.7 mm in columns measuring 5 cm dia × 126 cm long was used to study effects of interrupted irrigation ('rest' periods) on metal ion release and leaching bacteria. Copper tenors increased approximately 16 fold and bacterial iron oxidation activity three fold following a 14 day 'rest'. A linear relationship between copper tenor and bacterial activity demonstrated that this experimental system was effective for quantitative studies of bacterial leaching in ore colums.

Jan 1, 1981

A study of the swelling behaviour of a single batch of high-grade iron ore pellets during hydrogen reduction in a fixed bed showed that the extent of swelling is governed by the nucleation and growth of crystalline iron protuberances from the wüstite grains. Over the reduction temperature range 650 to 1000°C, it was found that substantial degrees of swelling can occur at temperatures in excess of 850°C, and significant variations in the swelling behaviour of individual pellets from different bed levels are observed under these conditions.The results are discussed in terms of a recent swelling theory and shown to be in general agreement.

Jan 1, 1978

Support design in jointed or blocky rock masses is often approached by the use of either 'rules of thumb', rock mass classification systems such as the Q-system (Barton, Lien and Lunde, 1974) or RMR (Bieniawski, 1973) or conventional wedge analysis. Generally, this requires that a number of key simplifying assumptions are made and the support system is designed to cater for either a mean, most likely, or worst case scenario depending on the risk tolerance. The design block size is often a major uncertainty and often a worst case block size based on excavation span is used. Thompson and Windsor (2007) state that it is inappropriate to base support designs on the excavation size as these size blocks rarely occur if discontinuity trace lengths are considered. Probabilistic keyblock methods can be used to determine the most likely design block sizes. A methodology is presented whereby JBlock software (Estherhuizen, 1996) is used to estimate potential block sizes as part of the support design process. Using information such as the spacing, orientation and length of discontinuities, it is possible to simulate blocks in the walls of an excavation (Esterhuizen and Streuders, 1998). Keyblock analysis methods (Goodman and Shi, 1985) are used to evaluate whether blocks are removable and whether the chosen support will be sufficient to ensure stability. Data from two mines is used to demonstrate how probabilistic keyblock analyses can be used in support design. Discontinuity data was used to generate 10 000 removable blocks and the design block size statistics were determined. For one mine this information was used to scale blocks in a conventional. Unwedge analysis whilst for the other mine, the point estimate method (Harr, 1987) was applied. The choice of appropriate design acceptance criteria in terms of factor of safety and probability of failure is also considered.

Nov 25, 2010

The injection of grouting compounds into the consolidated rock surrounding underground mine workings has long been practiced for the purpose of sealing against water flows. In more recent times however, grout injection has also found application for the purpose of rock mass reinforcement. Mines in Europe,America, Australia and elsewhere now make use of significant quantities of chemical grouts in both preventative and remedial strata control work.   Despite the increasing usage of grouting for these purposes, there is limited knowledge about the effects of grout injection on the rock mass, and acceptance of the method is by no means universal. In some cases grouting has been applied with little understanding of the factors that control its effectiveness, and disappointing results have been obtained.   This paper reviews the basic concepts of how grout injection may contribute to the control of rock surrounding underground mine excavations, and highlights the factors which may serve to limit the efficacy of the method and the uncertainties that complicate the appraisal of grouting as a method of strata control.

Jan 1, 1994

The uptake of nickel into the lattice of pyrrhotite, Fe1 _1J S was studied experimentally in the temperature range 200°C to 760°C. Nickel from both aqueous solutions and salt melts diffuses rapidly into the sulphidelattice with an accompanying release of iron into the solution or melt. The rate of uptake of nickel and its diffusion into the sulphide lattice were followed by optical microscopy and by analysis with an electron probe microanalyser. Some geological consequences of this phenomenon affecting the distribution of nickel in rocks associated with nickel-iron sulphide ores are discussed.

Jan 1, 1972

By Litvinenko V. I

Being a source of structural materials for many centuries, the modern image of the ferrous metallurgy is burdened with obsolete technologies with disregard towards new environmental protection requirements. The production cycle of metallurgical products have two clear-cut stages: I . production of liquid metal and casting into steel billets; and 2. processing of steel billets in solid state under high temperature to produce various shapes and profiles of metal products. Plastic deformation of metal at the second stage is least associated with environmental pollution and is presently being provided with more and more advanced equipment.

Jan 1, 1999

The National Economic Viewpoint? Any substantial project undertaken by private enterprise would normally be subjected to a Discounted Cash Flow analysis of its commercial viability, and would proceed only if the rate of return was judged satisfactory. A 'national viewpoint' analysis attempts to do the same but from the viewpoint of the community as a whole. The objective is to ensure that those projects are undertaken which yield the best return, economic and social, to the nation as a whole.

Jan 1, 1984