Search Documents

By A E. Annels, G F. Johansen, B W. Cuffley

Nuggety gold-quartz reefs are characterised by localised, high-grades and in many cases coarse free-gold. Geometrical and grade complexities are often observed. The high-grade regions are generally erratic and have a low continuity; though may make the deposit economic. Viable grades are generally contained within discrete oreshoots, which are surrounded by barren/low-grade material. Drilling is an effective measure of geological continuity, however grade distribution can only be reliably obtained from underground development and bulk sampling. In general terms, only an inferred resource is likely to be estimated from surface drill data alone. Underground development, further drilling and probably bulk sampling will be required to delineate inferred and indicated resources. Closely spaced development with bulk sampling is likely to be the best way to determine a probable reserve. The resource evaluation process must driven by a clear geological model that should attempt to understand the controls to reef geometry and grade distribution. Geological interpretation has traditionally been undertaken in two-dimensions, though computer software is now being used to produce three-dimensional models. Grade interpolation has generally been undertaken using classical methods, typically weighted averages, zone of influence weighting and polygonal/sectional blocks. Tonnages can generally be calculated from diamond drill and development information with a reasonable degree of confidence. Grade is much more difficult to define with confidence because of its highly erratic and discontinuous nature. To account for variability it is recommended that a best estimate be reported within a grade range, as this more accurately reflects the uncertainties involved. Reporting should be undertaken within the framework of the JORC code, but should involve special consideration of grade reliability.

Jan 1, 2000

By R Salmon, C Jones

This paper examines the recent trend towards sustainability reporting and the application of the Global Reporting Initiative (GRI) æSustainability Reporting GuidelinesÆ. It also reviews reporting in the context of the Australian Minerals Industry Code for Environmental Management, as well as the status of public sustainability reporting globally in the minerals industry. The public reporting of environmental, health and safety, social/community and economic performance has evolved over the past two decades. Initially, separate and to some degree disparate documents were produced to report performance in each distinct area. In the early to mid 1980Æs some organisations had begun to report their environmental performance through some minor commentary in their annual financial reports or through ætokenisticÆ leaflets, often used as public relations exercises. Due to more media coverage and an elevated level of public scrutiny, organisations are no longer merely reporting their good performance, but also their bad and indifferent performance. In recent years these once separate environment, health and safety and community public reports have further evolved to become more integrated, reflecting organisations embarking on the reporting of their progress towards sustainable development. The primary factor in driving the evolution of sustainability reporting has been the increasing influence of stakeholders. Two groups of external stakeholders that have had a significant influence over public sustainability reporting in recent years have been non government organisations (NGOs) and socially responsible investment funds. Significant expenditure is involved in the preparation and publication of a sustainability report however many organisations do not appear to have examined in detail what they are really trying to achieve from their public reporting process. It is important to establish objectives for the public reporting process to achieve maximum benefits. Without a framework of public reporting objectives, the benefits of the reporting process to the organisation will not be recognised and the considerable expenditure involved will be increasingly difficult to justify. We believe that by focussing on the process rather than the document, significant benefits to the organisation can be gained. Indeed, with a proper framework of objectives and targets, the reporting process can be used as a vehicle to drive organisational change, implement management systems and improve performance. An idealised framework for a public sustainability reporting process sees the organisationÆs sustainability policies drive the entire process and determine the sustainability objectives. Specific targets are then set to realise those objectives. The targets will govern performance indicators that should be used to measure the success of target achievement and which will also define what data need to be collected. Evaluation is a key component of the reporting process to measure the success of target achievement and progress in realising objectives, as well as review the need for new targets to be set. The actual production of a public document is only one, albeit important, component of the overall reporting process. The challenges that lie ahead for sustainability reporting primarily relate to the integration of environmental, social and economic performance reporting as organisations integrate their approach to these areas. This will only happen as the culture of an organisation changes to not only accept the principles of sustainable development but to implement those principles in daily operations. The reporting process has the potential to drive that cultural change by communicating the organisationÆs sustainability objectives and setting challenging targets for their realisation. Public sustainability reporting will only achieve its maximum value when it forms an integral part of an organisationÆs sustainability management system and culture.

Jan 1, 2002

By S Hanke, J Burden, P Spies

The Waterview Connection will complete Auckland’s long-planned Western Ring Route, a 48 km north-south motorway alternative to State Highway 1 that bypasses the central city to the west. The project involves construction of 5 km of new motorway – half of it underground in tunnels – to connect the Southwestern (State Highway 20) and Northwestern (State Highway 16) motorways.The Western Ring Route will link the major population and industrial centres of Manukau, Auckland and North Shore to give the region the connected and resilient strategic road transport system it needs to underpin economic growth and sustainable development. It will also provide a direct motorway link between Auckland’s central business district (CBD) and international airport.The project involves construction of twin 2.4 km driven tunnels with an outside diameter of 14.41 m beneath residential suburbs, a major arterial road and a rail corridor. Enabling works began in January 2012 while tunnel construction using an earth pressure balance (EPB) tunnel boring machine (TBM) began in November 2013.This presentation introduces the Waterview Connection project, its role in the development of the Auckland motorway network, its procurement process, the alliance delivery model and an overview of the project’s design features and construction progress to date.Design and construction highlights of the presentation include the TBM start-up, turnaround and breakthrough arrangements as well as the experience gained during the first tunnelling drive. The presentation also covers an innovative process developed for invert construction behind the TBM that is independent of tunnel excavation.CITATION:Spies, P, Burden, J and Hanke, S, 2014. The Waterview Connection Project – progress to date, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 519–540 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By P S. Heithersay, M McGeough

The discovery of Olympic Dam in 1975 and, more recently, Prominent Hill in 2001 and Carrapateena in 2005 demonstrates the potential for world-class IOCG deposits in South Australia. Potential for further discovery of large IOCG mineral deposits in the Gawler Craton and the Curnamona Province is high because of continental-scale pervasive iron-rich alteration, crustal-scale structural preparation and unique magmatic-hydrothermal conditions. Recent exploration successes point to the effectiveness of new exploration tools and technologies to locate this style of mineralisation under cover. The gold endowment of these orebodies located in South Australia exceeds 75 Moz, with further discoveries to come. The lead time between discovery and development of the multi-million ounce Prominent Hill copper-gold mine in less than seven years demonstrates how quickly this style of deposit can be brought into production in South Australia. Clearly these long-life, multi- commodity IOCG deposits mines are an immediate exploration and future growth opportunity for the gold mining industry to replace ever depleting gold inventories.

Jan 1, 2007

The Effect of Molecular Weight on the Adsorption and Efficacy of Polysaccharide Depressants

Sep 13, 2010

By N Pirouznia, F Rashidi Nejad, S Naraghi

Sungun Copper Mine, which is the second largest copper mining operation in Iran has a large tailings storage facility with a seepage control dam located downstream of the main dam. Surface and groundwater in surrounding area of the tailings storage facility has been monitored for ten years. This paper will discuss the results of the surface and groundwater monitoring and seepage control at the Sungun Copper Mine. The results of the study show that if the tailings storage facility influence the water quality of the rivers, this effect is not significant, so that the prevailing parameters of the measured parameters were within the permissible standard of drinking water in Iran.CITATION:Rashidi Nejad, F, Naraghi, S and Pirouznia, N, 2018. Surface and groundwater monitoring and seepage control at the Sungun Copper Mine, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 439–453 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By L Mottola

Three decades ago mining companies, principally in North America, aided by machine and explosive manufacturers, started significant attempts to develop and implement automated mining systems, mainly underground. These tended to be motivated by decreasing cost, increasing productivity, reducing labour requirements, and improving safety. These are important business drivers, however, little attention was given to the underlying goal of mining automation, namely to bring upstream processes in control and reducing variation, as seen in downstream mineral processing plants.This paper first reviews the nature of Lean Thinking and its application in the context of the growing commitments by industry to develop future automated mine production systems. The paper then makes reference to prior and current experiences in open pit blasthole drill and shovel performance monitoring, to demonstrate the principle that machine performance data offers as a means, not only to characterise the dynamic geological and working environment, but also to provide a foundation for automation. In this case, drill and shovel monitoring was originally motivated as a means to optimise blast fragmentation through more effective drill and blast designs that are based on an accurate determination of the bench geological and geotechnical characteristics, hence managing variation in the drilling and blasting process. This paper considers how automating and integrating such components of the mine production system would bring processes into a controlled state, creating value at the face, within a framework of Lean mining.

Nov 22, 2011

Ok Tedi Mining Limited has recently completed the first phase of a trial to compare the performance of D26B Krebs cyclones in different configurations to the new Warman 650 mm CAVEX cyclones. From 1992, rougher flotation feed size has increased from the target d80 grind size of 150 ¦m with increasing SAG mill throughput. At high SAG mill throughput, operators have difficulty maintaining the target cyclone feed pressure and must increase the cyclone feed density, thus resulting in a coarsening of the cyclone split. Warman International have developed the CAVEX high capacity cyclone. The new CAVEX cyclones, when compared to the Krebs units appear to:produce a measurable increase in volumetric flow for the same pressure drop; maintain or decrease the proportion of coarse particles reporting to overflow; and lower the overflow density. In all plant trials to-date, the CAVEX cyclones appear to be superior to the standard Ok Tedi Krebs cyclones. Further testwork is planned to evaluate modified Krebs cyclones (with recent design improvements) against the CAVEX cyclones.

Jan 1, 2000

The recent boom in the mining industry has lead to some unique challenges in successfully operating processing plants. With high turn-over rates of both operators and technical staff, and many experienced personnel leaving regional sites for city based jobs there is often an onsite knowledge vacuum and this in turn puts pressure on both site training departments and senior metallurgists to provide the relevant skills to the continuous stream of new staff. Frequently both operators and new metallurgists are instructed on a æhow-toÆ basis rather than giving them the understanding as to why tasks are performed and decisions are made. This paper has been written with the plant operator and metallurgist in mind and aims to provide suitable material to be incorporated into a site training manual. Topics have been broadly divided into the following categories: factors that operational staff can control; including pulp density, air addition rate, froth depth, particle size and reagent type and use; factors that operational staff cannot control; providing general information on bubble size, froth stability, pulp chemistry and the mechanical effects of the rotor/stator system; and process improvements. Each topic is discussed with a view to clarifying the key process variables that need to be understood and optimised in an industrial operating plant.

Jan 1, 2009

By J Addai-Mensah, M Adam, W Skinner, J Begelhole, K Quast

Granulation of iron ore fines into robust granules is critical to successful sintering and blast furnace operations in iron and steelmaking. Iron and steelmakers desire iron ore granules with high strength, uniform size distribution and low fuel consumption to enhance efficient sintering operation. Unlike hematite ore, magnetite concentrates do not granulate easily at low binder dosage to yield coarser granules due to the absence of nucleus particles. This motivates the present study to harness the complementary properties of hematite ore to enhance granulation of magnetite concentrates via blending. The current state-of-the-art in hematite and magnetite blend granulation is reviewed, along with granule property limitations. Preliminary experimental work on granulation of hematite and magnetite blends as a precursor to sintering is reported.CITATION:Adam, M, Addai-Mensah, J, Begelhole, J, Quast, K and Skinner, W, 2017. Enhancing magnetite concentrate granulation by blending with hematite ore, in Proceedings Iron Ore 2017, pp 17–24 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By S Hapugoda, J R. Manuel, M J. Peterson

Microindentation testing using the square–pyramid–shaped Vickers indenter is a well-established technique to determine the microhardness of minerals and materials. However there is a paucity of published microhardness data from Fe ore samples. It is acknowledged that an iron ore’s particle mineralogy and texture is critical to its processing properties, and it is therefore considered that the microhardness of different mineralogical/textural types may also relate to these properties. Mineral microhardness potentially provides inputs to the modelling of breakage characteristics during comminution, as well as the relationship between mineral chemistry and microhardness, and mineral microporosity and microhardness. Microhardness can be determined as single crystal microhardness, for more coarsely microcrystalline samples, or as ‘aggregate microhardness’ for cryptocrystalline or finely microcrystalline samples.Variations in the texture and mineral chemistry of common Fe ore minerals (eg martite and microplaty hematite, ochreous and vitreous goethite etc) are well established and this study provides microhardness data on different textural forms of Fe (oxyhydr)oxides from a variety of different Fe ore deposits. The data indicated that in general, the mineral grain size, microporosity and texture were the main influences on Fe (oxyhydr)oxide microhardness. There were no apparent systematic variations between microhardness and minor element mineral chemistry, with the possible exception of Al content in goethite (for goethites with Al content >0.5 wt per cent), and for goethite total element contents >90 wt per cent (determined by electron probe microanalysis, EPMA). Higher Al concentrations and lower total element concentrations in goethite EPMA analyses correlated with lower goethite microhardness. Microporosity and grain size were more important than texture to hematite microhardness. Different textural forms of dense hematite (eg martite, recrystallised interlocking hematite and specular hematite) with similar grain size exhibited comparable microhardness. Microhardness values for hematite and hydrohematite with little or no evident microporosity were also similar, whereas more porous forms of martite, microplaty hematite or hydrohematite exhibited lower microhardness.CITATION:Peterson, M J, Manuel, J R and Hapugoda, S, 2017. Microhardness testing of hematite-goethite Fe ores – implications for their textural characterisation and geometallurgy, in Proceedings Iron Ore 2017, pp 319–330 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By K H. Esbensen, K Engström

The conclusion from the debate over the last decade in the mining sector is that, for grade control, reverse circulation (RC) drill sampling gives more reliable results due to less sampling problems than blasthole samples. However, by conducting the latter with well-controlled procedures there still exist fair possibilities to counteract the major blasthole sampling problems and achieve fit-for-purpose representativeness, especially if based on minimal loss of fines. In the present PhD study, extensive replicate experiments and variographic characterisations are conducted to evaluate the performance of manual blasthole (BH) sampling and sectorial segment sampling. The experiments were performed in Luossavaara-Kiirunavaara AB (LKAB)’s Leveäniemi open pit mine in the north of Sweden. The experimental area is an apatite-magnetite iron ore deposit of the Kiruna type, with the demand to exhibit a maximum of local heterogeneity to allow the experiment the largest possible conclusion powers. Gathering and splitting the complete BH drill cutting cones (fines cone, coarse cone) served as an authoritative reference on which to assess the representativity of the two BH sampling methods.Results show that manual BH drill sampling is able to produce samples with an acceptable accuracy and precision if performed properly and with insight. Based on variographic comparison, segment sampling shows similar precision for chemical grades as the manual sampling, while the particle size distributions were more deviating for segment sampling than for manual sampling at the high and low size ranges. Possible reasons for these partly surprising results are discussed.For further investigation of the performance of BH versus RC drill sampling, a second experiment has been planned on a parallel profile. This will result in an unprecedented opportunity for a full variographic comparison between RC and BH sampling, aimed at designing specific, fit-for-purpose sampling procedures as a function of ore quality, cut-off grades and important contaminant levels.CITATION:Engström, K and Esbensen, K H, 2017. Blasthole sampling (replicate and variographic experiments) in LKAB open pit iron ore mines – fit-for-purpose representativity?, Australia, in Proceedings Eighth World Conference on Sampling and Blending , pp 85–96 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017

The purpose of this paper is to list by tabulation and flow sheet, the operating equipment and installations in use at Rosebery, and to refer to particular items which may be of interest for purposes of comparison, or because they possess some unusual feature. The general perspective has been taken from the viewpoint of operating and maintenance experience.The sequence begins with ore breaking and transport and proceeds through milling operations. The paper is in two sections, first, mechanical equipment, second, electrical equipment. A brief outline of a scheme for using gravel wash for stope filling, which is in course of installation, has also been given.

Jan 1, 1949

During the past Two years in reef gold mining, "indicators" have received great attention at the hands at the Victorian gold seekers. Many years ago, what was caned the" indicator lode," was struck in Ballarat East, on the course of which extremely rich deposits of gold were discovered but as to its being a .qeneral experience in reefs or leaders no one ever dreamed. Now, however, we find that these "indicators" are frequently to be met with, though they differ very much in different localities, making it, therefore, a difficult matter for other than a careful minel' to follow them. The necessity of following "indicators" for the purpose of developing gold is now recognized, and the policy of following them up has been attended with much success in this field. In the case of Messrs Shaw and Sons, at Wedderburn, those gentlemen began to work on an "indicator" here five years ago, and immediately thereafter more by accident than anything else they being at that time inexperienced as regards "indicators " came upon gold bearing quartz, which continued payable so long as the" indicator" aud the stone were in conjunction with each other, but as soon as they parted company the stone ceasedto be of any value then, by following the" indicator," as the latter intersected fresh bodies of stone they proved again more or less payable, until a fortnight or so ago the Messrs. Shaw turned out 4 tons of stone, which yielded £1,825, with also profitable workingup to the present moment. Where they are now working is a mile north of their original find thus proving that "indicators" travel considerable distances and have something to do with the gold deposits found in reefs. On the direct course of Shaw's "indicator," as high as hundreds of ozs to the ton was obtained from the stone but, just a few inches from either side in the same" leader," not a colour could be got. Whatever the cause-whether by electricity or some unknown force in nature-the gold is found on the course of these" indicators" and nowhere else, and-as each of the Victorian Government Geologists admit-their value to the gold-seeker as a means of leading to' gold cannot be over-estimated.

By D Craw, P Upton

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The Otago Schist belt of southern New Zealand hosts widespread orogenic gold deposits. Erosion of these orogenic gold deposits has led to the formation of numerous placer deposits distributed across and beyond the host schist belt. Numerical modelling of crustal scale deformation and geomorphic evolution has defined the key tectonic features that have controlled the severance of detrital gold deposits from their sources. Tectonic activity over the past 20 million years, during development of the modern Pacific-Australian plate boundary, has severed links between some placers and their sources. Detrital gold was transported south from the Otago Schist source region in two different river systems in the Miocene. Mesozoic orogenic gold deposits shed gold into rivers that flowed to the south. These rivers were terminated by the rise of north-west-trending basement ridges at the boundary between weak schist crust and strong greywacke crust, and the ridges were controlled by pre-existing faults at that rheological boundary. In contrast, rising mountains close to the developing plate boundary in the Miocene were the locus of new orogenic gold deposits hosted in extensional faults. These gold deposits were rapidly exhumed and contributed detrital gold to orogen-parallel Miocene rivers that flowed to the south-west. Pleistocene deformation on mainly north-west and north-east orientations, and associated river capture, has severed the links between these Miocene orogenic deposits and downstream detrital gold.CITATION:Craw, D and Upton, P, 2015. Tectonic severance of links between placer gold and its sources, southern New Zealand , in Proceedings PACRIM 2015 Congress, pp 541–544 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By S C. Dominy

For any gold deposit-based geometallurgical study, the collection and processing of representative samples for gold grade and recovery tests is critical. Sampling protocols should be designed to suit the style of orebody in question. The proportion and size of gold particles has a direct impact on the effectiveness of sampling protocols and metallurgical recovery processes employed. Studies focussing on ore mineralogy and gold particle deportment, size and distribution are required. Key issues are the presence of gold particle clustering (important for sampling optimisation) and proportion of coarse versus fine to refractory gold. X-ray computed tomography (CT) is a radiographic technique that produces high-resolution 3D computerised models of objects based on density distribution. The ‘virtual’ specimens are made up of voxels, the 3D equivalent of pixels each assigned a grey value based on X-ray absorption. This paper presents the results of recent research on the imaging of in situ gold particles in a coarse gold-bearing ore. The technique shows promise as a rapid non-destructive method for preliminary characterisation to facilitate more detailed studies. Early and rapid gold particle determination enables sampling protocol optimisation and metallurgical recovery parameters to be defined prior to detailed feasibility studies

Sep 5, 2011

Near-Infrared Spectroscopy (NIRS) Sorting in the Upgrading and Processing of Skorpion Non-Sulfide Zinc Ore In 2008 Anglo American sponsored a research project at RWTH Aachen University to assess the feasibility of the use of near-infrared spectroscopy (NIRS) for ore waste discrimination at the Skorpion zinc mine. The Skorpion mine is an open pit zinc mine located in Namibia, owned by Anglo American with an annual production of 150 000 t/a of super high grade pure zinc. Opportunities for the implementation of NIRS sorting for the Skorpion process exist to upgrade currently subeconomic material, including the marginal dump (over 2000 000 tonnes, av grade of 2.5 per cent Zn). NIRS sorting is not yet implemented or established in the minerals industry however it is a proven technology in the plastics recycling industry, where more than 2000 NIRS sorters have already been installed. NIRS sorting, a type of sensor-based sorting, is a single particle sorting technique which classifies the particles based on the absorbed/reflected radiation in the near-infrared (NIR) region. A disadvantage of NIRS is that it is a surface measurement technique, but NIRS sorting shows overall great potential for the minerals industry. Skorpion ore minerals include zinc bearing phases such as sauconite, hemimorphite, smithsonite, and hydrozincite. These display diagnostic responses in the near-infrared. There are three major absorption features that characterise the reflectance spectra of the ore bearing minerals. These are due to OH and H2O molecular bonds. The spectral response of the waste material is caused by other minerals such as non-zinc-bearing clay minerals, calcite and impure quartz. Test work showed that it is theoretically possible to separate ore material from most waste material based on spectral response in the NIR region. In addition to upgrading material by removal of waste it is also potentially feasible to classify the material based on zinc grade. A tentative correlation between zinc grade and spectral response seems to exist for the sample test suite in the NIR region.

Sep 13, 2010

Tumbling mills and some theoretical and practical aspects of milling are discussed. Attention is directed towards the difficulty of relating the dynamical analyses of the motions of particles within mills to the existing treatments of breakage processes. This synthesis may be advanced by a study of milling that utilizes the matrix analysis of breakage processes. Application of the matrix analysis to results obtained on (i) grinding in open-circuit a zinc ore in a conical pebble mill and in a modified conical mill, (ii) "grinding of cement clinker in a compound mill, and (iii) to some drop-weight grindability tests is discussed. It is shown that the 'IT-breakage model adequately describes the breakage processes of each of the tests. (The proportion broken in each breakage cycle is given by 'IT and is independent of particle size.)The size distributions of the products are accurately predicted in the cases considered. Matrix analyses of the breakage of coals, various ores and a cement clinker have been made. Appendices give an elementary account of the matrix methods and give the equations fully describing reverse order closed circuit operations. The matrix analyses of breakage processes and the survey are used to examine briefly closed circuit grinding.INTRODUCTIONTumbling mills are slow-speed crushing and grinding machines which have been developed from some fairly simple types into many widely differing forms. Many of these versatile mills have proved extremely useful in ore dressing and mineral beneficiation, whereas others have been used in the cement industry and less extensively in the coal industry.The performance of even the simplest tumbling mill is very imperfectly understood, whilst the more difficult problems associated with the balancing of complex milling circuits and with the establishment of the optimum operating conditions for the whole of a complex circuit are even less well apprehended.Our knowledge of the performance of tumbling mills is rather sharply divided into two categories: the first consists...

Jan 1, 1957

By J Fut=

The rotary drilling of rocks is widespread technology in mining and in tunnelling. The paper describes the results of research by aim to find relationships between optimal drilling and sound signal of drilling machine. The optimisation criterion has been formulated as the minimisation of specific energy with maximal effective speed of drilling in process of the rock disintegration. The research in this field has been made on experimental drilling stand. Our monitoring system has measured following variables: the pressing force of core drill, the revolutions of drilling head, the length of drilling, the time, the power, and the acoustic signals. For measurement of acoustic signals have been used very sensitively sound meter MEDIATOR 2238. From this measurements have been processed acoustic spectrums. Then we are found relationships between optimal control of drilling and composition of acoustic spectrum. On base of experimental results, we can formulate the optimal control following: æTo achieve the minimum difference between the equivalent sound level at the load and idle modes only at the representative frequency (f = 1000 Hz)Æ. The representative frequency dependences on type of the rock New method based on these relationships enables the optimal control of drilling machine by using measured acoustic signals only.

Jan 1, 2003

By R Stosch, D Lohberger, J Rodler, E Schnell and A Bassler, H Ramseier

In the last two decades three-dimensional (3D) computational fluid dynamics (CFD) simulations have become an important tool in engineering sciences. More recently, the safety requirements in underground railway stations have increased with regard to incidents. For this reason, existing underground stations (eg Munich, Strasbourg and Berlin) are being equipped with smoke extraction facilities to protect passengers from smoke and visibility impairment in the event of fire. In addition, designs of planned underground stations (eg Karlsruhe, Doha) also include these facilities.For the commissioning of ventilation engineering systems with complex structures, the functional testing of the whole technical installation are important, as are the acceptance tests of ventilation and equipment parts. This functional testing includes not only the technical inspection of the equipment but also the acceptance measurements of the capability of the equipment and the execution of hot- or cold-smoke tests to confirm the effectiveness of the ventilation system.Due to the fact that the overhead contact line and other sensitive installations were already installed in the tunnel roof at the time that smoke tests were proposed, hot-smoke tests with fire loads up to a maximum of 1 MW could only be executed. Therefore, the evidence of the attainability of the safety objective had to be provided computationally in this special case with a fire scenario of a heat release of 10 MW using CFD simulations.This paper presents the interplay between the results from acceptance testing and smoke tests and the use of 3D CFD simulation and virtual reality using the example of Allmend station, which was repositioned underground and is part of a new section of track from Lucerne railway station to Kriens in the Zentralbahn network. The steps of the verification and validation of the computer model are presented with the real tests and measurements.CITATION:Stosch, R, Ramseier, H, Lohberger, D, Rodler, J, Schnell, E and Bassler, A, 2014. Safety in underground railway stations – an example of the interplay between testing and 3D computational fluid dynamics simulation, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 103–112 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014