Search Documents

The Channel Tunnel is an outstanding example of an undersea tunnel and its design illustrates most of the unique features of this type of tunnel. The marine site investigation was partic- ularly vulnerable to adverse weather conditions. To minimise this interference the time the drilling vessel was required to remain on station was kept to a minimum by expediting the drilling and the insitu tests as far as was practicable. To avoid additional unforeseen costs the contract documents were framed to take particular account of marine practice. The limited access at the coast line meant that for economy, maximum tunnel advance rates had to be attained. Ground excavation, handling and disposal methods and the provision of the lining were optimised and equipment specified in detail to ensure that no one com- ponent was delayed by a lack of capacity or mechanical failure in any other.

Jan 1, 1976

By A G McLean

This paper will first discuss the fundamental requirements for reliable discharge of backfill by gravity alone at high per cent solids. This discussion will include brief mention of the underlying principles of saturated solids flow contrasted to that of stirred tank or dilute discharge systems. Here the need to possess full knowledge of the flow properties of the stored material will be highlighted. In regard to attainment of reliable discharge it will he revealed flow from a backfill silo will only occur provided: ò the flowing material in the converging channel is yielding throughout; ò slip is occurring along the walls; ò an arched stress field is present in the vicinity of the outlet; ò the flowing backfill must be dilating to flow in response to the dilating stress field; ò sufficient dilation water is injected, in the hopper, to eliminate the formation of adverse interstitial pressure gradients; ò sufficient dilution water is injected, downstream from the hopper outlet, to generate a pumpable slurry of maximum per cent solids; ò the silo level must be sufficient to prevent the pump suction forming a rathole; ò the system must be configured and operated to generate stable discharge density; and ò the system must be configured and operated to minimise damage to the pump liners. In addition proper account must be made of the silo overflow weir and settling capacity to match plant throughput. Here opportunity will be taken to highlight the complexity of this multi-phase flow situation as well as the general yet paramount requirements for reliable solids flow. It will be shown that by proper attention to the multi-phase considerations gravity discharge of slurries as a consolidated bed with minimal water content is possible. Such high solids discharge results in greatly reduced demand for process water. In addition pumping costs are reduced as is the delay time associated with the mine drainage operation. Confirmation of successful applications will be highlighted by reference to several recent case studies. In the concluding phase mention will be made of the key yet very simple and effective operation techniques which enhance reliable Discharge.

Jan 1, 1998

By Y V. Haarlem, P Coghill, N G. Cutmore, M Millen, I Carter

Due to the low concentration of gold, ore sorting for gold has always required measuring indirect properties, such as density or colour, to allow separation on a rock by rock basis. This only works on an ad hoc, by deposit basis and is likely to be least reliable where it is most required in low grade ores. One candidate technique, Gamma Activation Analysis (GAA) has been demonstrated to directly measure gold extremely accurately in powder samples of around 500gm and is used in the Chrysos PhotonAssay assay system. This method uses a linear accelerator (linac) to generate the X-ray radiation that activates the ore at low levels to emit a characteristic gold gamma ray that is then measured by a radiation detector. CSIRO is adapting this measurement technique to application on a belt at up to 800tph to measure pods of ore. The principal differences between measuring samples and an on-line measurement of pods are the requirement to measure coarse ore (<50mm), to measure a larger volume of ore as uniformly as possible, and to have an open-ended geometry with adequate shielding of the linac radiation source. These issues have all been addressed with measurements of coarse ore reported down to around 1ppm in sub-optimal test conditions. They have been demonstrated for <75mm particles with detectors capable of measuring a large volume geometry continuously. These are projected to allow measurements down to 0.3ppm in more optimum conditions for a 10 second measurement time period where the U/Th content of the ore is less than ~10ppm. Extensive Monte Carlo modelling has demonstrated that adequate shielding can be provided in relatively simple geometries with only 1 right angle transfer in the material handling. Steady progress is being made to reach the technical position required to trial an ore sorting system.

Nov 10, 2020

By J Kinal

Plant trials are at the best of times difficult to perform; given variations in the ore, operating practice and economic constraints placed on a plant. Testing grinding media at industrial scale adds a further level of complexity that needs to be accounted for.Laboratory test programs consistently demonstrate that altering the grinding chemistry through the application of inert grinding media has the potential to provide significant metallurgical benefit. However, prog- ressing from laboratory testing to industrial trial is often an agonisingly slow process that can lead to inconclusive results which raise more questions than give answers. There are many factors that need to be considered when conducting plant trials aimed at demonstrating the impact of inert grinding media on metallurgical performance. The decisions (or lack thereof) made during the planning stage can heavily impact on whether a statistically meaningful result is achieved. Various factors such as how the trial is conducted (dumping or purging the charge); the circuit configuration; collection of the right data; and even the human factor will affect the outcome. The authors will use examples to demonstrate the importance of proper planning and controlled operation on grinding media plant trials.

Jan 1, 2009

The ore deposits investigated are composed primarily of hcmatite and can be grouped into three categories depending on the amount of leaching of silica and carbonate which has occurred from the original iron formation, and on the amount of recrystallization of the hematite. Minor constituents are magnetite. goethite, and quartz.Texturally. there are five different types of hematite, formed at different stages during the genesis of the ores.These are1. anhedral hematite grains formed by recrystallization of hematite already present in the original iron formation.2. hematite formed by martitization of euhedral magnetite, 3. massive aggregates of fine- to medium-grain hematite formed by recrystallization of (l) and (2).4. tabular or prismatic hematite grains occurring around the boundaries of the massive aggregates or martite euhedra. and in fractures and5. specular hematite. which is present in fractures in ore types (l) to (4).Minor and trace-element analyses, determined using an electron-probe microanalyser. indicated that only silica (less than 0&#183;01 per cent) and cobalt (less than 0&#183;002 per cent) were present in the magnetite and hematite from unaltered iron formation and in the hematite from the ores. Low concentrations of trace elements are typical of magnetite in ores formed as marine precipitates. On the basis of the analyses alone. it proved impossible to distinguish between the five hematite types. A determination of the variation in rare-earth trace element contents between iron oxides in the iron formation and iron oxides in the ores indicates that the rare earths were depleted during ore formation. A possible explanation is that they were removed in solution with silica as it was leached from the iron formation.

Jan 1, 1971

By B, R E. Browner, H R. Watling

A number of hydrometallurgical treatment methods are being developed to extract copper from chalcopyrite flotation concentrate including microbial leaching and ferric sulfate leaching. However, chalcopyrite is difficult to process efficiently by hydrometallurgical methods as it exhibits slow reaction kinetics. Comparative leaching tests do not always satisfactorily explain or predict observed copper recovery, acid consumption, or differential leaching of minerals. This is especially true when reactive gangue constituents are present. The aim of this study was to determine how the leaching regime (microbial versus ferric sulfate) affects both the extraction of copper and residue mineralogy. Chalcopyrite flotation concentrate was leached at 30¦C and 65¦C using a pure culture of Acidithiobacillus ferrooxidans and a mixed consortium of thermophiles, respectively. In addition, the concentrate was leached at the same temperatures using 0.1 M ferric sulfate. Microbial leaching of chalcopyrite extracted more copper than ferric sulfate oxidation of chalcopyrite at 30¦C, demonstrating that the microbes promoted the solubilisation of copper at this temperature. This result was confirmed by leach solution analyses and residue analysis using quantitative X-ray diffraction (QXRD). More chalcopyrite was oxidized with ferric sulfate at 65¦C than at 30¦C (as expected). QXRD confirmed that pyrite reacted during ferric sulfate leaching at 65¦C but was relatively unreactive during lower temperature leaching. The high ferric ion concentration in the ferric sulfate leach at 65¦C led to significant precipitation of jarosite. This phase was only detected in small amounts at 30¦C in both the microbial and ferric leached residues. Sulfur also precipitated in the ferric leaching at 65¦C whereas no sulfur was detected in the microbial leached residue. Quartz was a relatively unreactive mineral phase regardless of the leaching medium and temperature. QXRD analysis indicated the residue mineralogy differed with different leaching regime.

Jan 1, 2004

By K Le Bron

Fatalities that occurred because of rock falls in off-reef excavations (excluding shafts) over the last three years range between ten per cent and 20 per cent of the total number of fatalities that have occurred due to rock falls in the South African mining industry. These rock falls, mostly exacerbated by blasting practices, occur because of failure on discontinuities within the rock mass. Among other reasons of their occurrence is insufficient support installation or the incorrect assessment of rock mass conditions. This report presents qualitative analysis intended to outline rock stability conditions in tunnels subjected to dynamic loading. Seismic waves including those created by firing an explosive charge in tunnel rocks are considered. The rock behaviour is monitored using geophones and extensometers variably installed to record the near and far effects of roof bolt support units on a dynamically loaded rock. The paper discusses the results of field investigations.

Jan 1, 1999

By Robinson J

A stibnite flotation concentrate from Costerfield in Victoria was found to contain 63.3 g/t An while its sizing distribution indicated that 81.6 per cent of the material was less than 38 ¦m. A 24 hour cyanidation test by a standard bottle roll method recovered 15 per cent of this gold. Pressure cyanidation under conditions of ambient temperature, 40 per cent pulp density, an oxygen pressure of 1000 - 2000 kPa and an initial NaCN concentration of 15 kg/t, resulted in a recovery of 65 pe cent of the gold after only two hours of leaching. Aqueous pressure preoxidation of the concentrate followed by the standard bottle roll cyanidation realised gold recoveries as high as 96 per cent. Conditions of 220¦C, an oxygen pressure of 1000 - 2000 kPa, 16.7

Jan 1, 1991

By D L. Kennedy

It has always been a challenge to accelerate the underground development progress by increasing the advance rate of each development round. Surveys have shown that most of the development rounds have only been pulled 84 per cent to 94 per cent of the drilled length. Where bare detonators have been used as primers, less advance rate is expected. In order to obtain a good understanding of the influence of priming upon the advance rate in underground development, a series of high energy primer trials has been conducted by Orica Explosives in the goldfields using various types of Orica high energy Anzomex « primers. It has been shown that development face has been pulled an extra 140 mm to 420 mm by priming with Anzomex « K primers compared with conventional primers. From all the trials at different sites, we have seen that the face pulled using K primers was more square than that pulled using conventional primers. Virtually, no butts and toe were left on the face developed using K primers. Computer simulation has been conducted using either a conventional primer, a bare detonator or a K primer as initiator. The study compared the predicted crack patterns developed around the toe of the hole and it was deducted that a detonator-initiated hole would leave a butt some 200 mm longer than that from a conventional primer-initiated hole, and a K primer-initiated blasthole would give rise to stronger initial p-wave, promoting crack development around the toe and increasing the ability to pull close to the full depth.

Jan 1, 1999

At the Waikato North Head Ironsand operation, NZ Steel Mining Ltd is using a Bucket Wheel Excavator&nbsp;û shiftable conveyor mining system to excavate Titanomagnetite bearing sand and clay. The system utilises two Bucket Wheel Excavators with a two level shiftable bench conveyor and common trunk conveyor to deliver the material to a processing plant. The system was commissioned in November 1984 and has proved itself to be a high capacity, low cost method of excavating. Techniques of handling high sand faces have been developed and the conveyor layouts are going through a process of change to cope with the variable geo technical conditions and remain within: the characteristics of the excavators. The safety requirements for operating the system have been of a high standard and the experience has increased the confidence of the Company and the Mines Department Inspector&apos;s, for the first Bucket Wheel Excavator Mining system in New Zealand.

Jan 1, 1986

By Buttrose RB

The Pine Creek gold mining development consists of a 1000000 tonne/yr open cut mine, a carbon-in-pulp processing plant and support facilities. The operation is located at Pine Creek, 230 km south of Darwin in the Northern Territory. The mine was officially opened in late October 1985, having been designed and constructed in less than twelve months, despite front end expenditure constraints and unseasonal cyclonic rains shortly after commencement of site activity. Non-traditional methods and attitudes were required to be adopted by both Engineer and Owner to successfully bring the project from preliminary design through construction and commissioning in a minimum time. Those areas which differ from the more traditional approaches to Project Management are examined together with a review of the advantages and penalties of these methods.

Jan 1, 1986

By R Berry

This paper looks at two ways to estimate the bulk mineralogy of the rocks for assay intervals. The aim is to find an efficient indicator of the most common minerals in the rock. Phase (modal) analysis has traditionally been done using visual methods such as point counting and image analysis. A modern version of this process is the X-ray point counting routine using the SEM-EDS based software. These methods are too slow and expensive for routine analysis of bulk sample mineralogy at the normal assay spacing.Two sources of data were considered that provide information that can be used to determine the mineral abundance in assay samples. The most widely applied method is (semi-) quantitative X-ray diffraction (QXRD). The QXRD method is most applicable to major minerals and has limited application to minerals at low abundance. The nominal detection limit is 0.5 per cent. Values below five per cent have large errors. A second, less common, method is calculation of mineralogy from chemical assay data. Conversion of chemical analyses to mineralogical analyses depends on the unique chemical composition of each mineral. Elements only found in one mineral are easily accounted for, but many compositions are ambiguous. Deciding on the actual mineralogy is not simple. Recalculation of mineral mode from chemical analyses is more accurate than QXRD when the correct minerals, and mineral compositions, are known.Where only a few QXRD analyses are available they can be used to setup a protocol for calculation of mineralogy from assay data. Linear programming works well in this environment. The best results are obtained when both H2O and CO2 are directly measured. Loss-on-ignition (LOI) should be included if these are not available.Where both QXRD and chemical analysis are available for all samples, the best results are obtained using the least squared method to merge the data sets assuming QXRD has much higher analytical errors than chemical assays. The combined method provides more robust results because the high abundance minerals are controlled by the QXRD measurements while the chemical assays improve the precision for low abundance minerals

Sep 5, 2011

By Holliday R, Floyd JM

A laboratory investigation was carried out to determine the distribution of gold between the products of lead-zinc concentrate smelting in the Imperial Smelting Furnace (ISF). Bullion, speiss and slag from the ISF at Cockle Creek were used as the starting materials to evaluate the effect of gold and copper content of products on the distribution of gold between phases under conditions simulating those in the ISF hearth. The ratio of gold in bullion to gold in speiss has a mean value of approximately 1.6 and is independent of the gold content of the bullion. The distribution coefficient of gold between bullion and speiss is dependent on the copper level in speiss and is lowered by increasing copper content in speiss. The ratio of gold in bullion to gold in slag is in the range 25 to 5700 and dependent on the gold content of the bullion. For low gold concentrations in bullion of the order of 1 g/t and a bullion to slag ratio of 1:3 the gold loss to slag is expected to be approx- imately 23%. In all tests the gold in slag remained low, in the range 0.05 to 0.5 ppm provided metal prills were not suspended in Slag.

Jan 1, 1986

By P Walton, L W. Armstrong, D P. Blair

Sydney is the capital city of NSW and has a population of approximately four million people. Eighty per cent of the cityÆs water is supplied by Warragamba Dam, which is situated some 75 kilometres south west of the city centre. A risk assessment was carried out on the dam and future predictions of water flows into the catchment area showed that there was a risk of a one in 700-year flood not being contained by the dam. The predicted loss of life and property damage warranted the construction of an auxiliary spillway on the eastern side of the existing dam to cater for any uncontrollable influx of water. A test blasting program was instigated and the blasting parameters were established that would lead to routine production blasting of the sandstone rock making it more cost effective to excavate. Blast induced vibrations were a concern to the owners and the dam wall and ancillary infrastructure was instrumented with sensitive vibration monitoring equipment during the test blasting phase of the operation. Once the blasting parameters were established from the testing program production blasting was carried out on a daily basis to maintain æstockpileÆ of fragmented ground for the excavation equipment. Blast vibration models were developed to predict vibration levels for more sensitive areas of the dam to give the operators more confidence in their operations. The blast induced vibration levels recorded did not cause any structural damage to the dam wall and the waveform frequencies of the blasting operation were much higher than that experienced during a recent earthquake. The integrity of the SCAÆs assets were at no time jeopardised.

Jan 1, 2001

By D Woolmer

Since January 2019, BHP Olympic Dam have been trialling the use of a drone based LiDAR mapping system for the purpose for surveying stope voids. This new technology utilises Simultaneous Location and Mapping (SLAM) algorithm providing positioning, stability and collision avoidance in GPS denied environments. Implementation of this system utilised underground personnel trained in the equipment’s use. The study’s intention was to evaluate the effectiveness of this equipment versus traditional surveying methods in regards to quality, safety and productivity. The trial results showed a marked improvement in the quality, productivity and personnel safety when conducting surveys. The use of the drone and LiDAR system reduced personnel and equipment requirements for surveys, thus allowing these resources to be deployed elsewhere. The technology’s simple and rapid deployment allowed multiple surveys to be conducted during a 12 hour shift, including ad-hoc work with minimal disruption to underground operations. After the drone’s initial trial, further work was conducted to utilise the Hovermap LiDAR scanner on other platforms to increase utilisation. A mounting system was created allowing the LiDAR to be mounted on a remotely operated loader or vehicle. This enabled drawpoint scans to be taken directly after production completion, resulting in faster stope close outs and drive scans for convergence monitoring. Implementation of the LiDAR system has resulted in improvements in the stope production cycle by reducing delays previously associated with data capture. The increase in the volume and quality of data has also allowed in-depth back-analysis of stopes in new mining areas to be conducted, which have driven improvements in the design process.

Mar 15, 2021

By Blackham M

West Wallsend No. 2 Colliery is a new mine that is presently being developed in the New- castle Coalfield by J. & A. Brown & Abermain Seaham Collieries Ltd., a subsidiary of Coal & Allied Industries Ltd. It is situated near Barnsley and is some 15 miles by rail from the port of Newcastle. The mine will produce coal from both Bore- hole and Young Wallsend seams. The Borehole seam has a working seam thickness varying from 7 ft to 5 ft while the Young Wallsend seam presents a choice of two distinct working thick- nesses, i.e. 5 ft. or 8 ft, the upper 3 ft containing much high ash material. The inter- seam interval varies from 10 ft on the western edge of the area to more than 70 ft in the central portion. The Borehole seam lies at a depth varying from 550 ft to 750 ft and the overlying surface terrain is gently undulating bushland with limited surface development.

Jan 1, 1972

By Davies B, Rogers A, Grainger A, Todd J, Brenman R, Jones L, Horton B, Eager L

Research into the control of diesel particulates (DP) has been. conducted by BHP Coal for more than 7 years. Personal monitoring of employee exposures (n = 480 full shift samples) conducted at nine underground coal mines has indicated that the exposure of the workforce ranges from less than 0.1 to 2.2 mg/m3 of DP dependent on job type and mining operation. Approximately 50% of the mass of DP captured is elemental carbon (EC) which is the species currently being considered by some international regulatory authorities as the exposure standard. Five technologies for controlling DP were investigated in a combination of studies conducted in an above ground simulated tunnel, in a special controlled section of underground mine roadway and validated by application in standard coal mining operations at Tower Colliery. Tests conducted under controlled conditions indicate that dependent on the type of fuel in use, the introduction of low sulphur fuels can reduce DP levels in return airways by up to 50% and in actual mining situations a reduction of 20% can be achieved in exposure of the workforce. In addition, subjective responses from the workforce indicate that exhaust emissions from low sulphur fuels provide lower irritation and a more pleasant aroma. The use of water filled scrubber tanks reduces the level of DP emissions by 25%. Chemical decoking of engines resulted in a reduction of 20% in DP in return airways. A commercially available non-flammable disposable dry exhaust filter constructed from synthetic organic fibres with an operational lifetime in excess of 20 hours was found to reduce DP exhaust emissions by 80%. Investigations have indicated that the use of increased ventilation to control DP levels particularly in multiple vehicle situations does not follow a simple dilution factor and in some instances compliance with current regulatory requirements may not produce the required reduced exposure levels. The results from single component control strategies provide considerable reduction in exposure to DP, however the most efficient and cost effective control methodology is the use of a combination of individual systems modelled to operations conducted at each mine.

Jan 1, 1998

In the pursuit of commercial solutions for environmental issues, individual problems are often identified, considered and resolved in isolation from other environmental matters and always at the end of the cycle û after the problem has been created. Inter-relationships are neglected if they are not seen to obviously impact on a specific problem and the issue at hand is plucked from the environmental landscape and dealt with in total isolation to all else. In a Zero Waste approach to environmental matters, all outputs are pursued as potential inputs. Industrial processes are viewed as a variation on natureÆs theme and opportunity pursued above all else. When viewed from this perspective, industry appears to have forgotten its origins. It has forgotten that it is principally about people. The juggernaut of global trade has forgotten that it is a small part of a big landscape and that its principal participants, people, cannot exist without healthy soil. Commercial activity in all parts of the world relies heavily on the ability of agriculture to produce the necessary inputs for industrial production. The care and nurturing of our soils is fundamental, not only to the survival of humanity, but also to the economic systems that support that humanity and to the industry which profits by it. Actual levels of domestic recycling in many countries around the world seldom reflect the 90 plus per cent desire to recycle recorded in surveys conducted by local authorities in almost every country. If the desire to recycle is far removed from the end result, why is it that the systems provided are so ineffective? It is obvious that what we do need is a recycling system that both engages and rewards the participant and stimulates the innate desire to support the environment. A recent trial in New South Wales, Australia, demonstrated that by giving individual households credits for recycling organic wastes, not only will contamination levels fall dramatically, but increased yields, improved soil structure, improved land values, reduced fertiliser costs and increased water use efficiency give the farmer good economic reasons for purchasing and applying quality composted product. By underpinning and securing the agricultural community, we secure the future of industry. The æCity to SoilÆ project linked the economic on-farm benefits of compost use with reduced contamination through the provision of rewards paid for by the purchase of product by the farmer.

Jan 1, 2006

How often does one hear that a recent feasibility study was not a success? Alternatively, when scope of the feasibility study was sent out to tender there was a large discrepancy in tendered prices. If the tendered prices were to be compared to the consumer market, for instance the purchase of a car, where the concept is transport in a controlled and safe manner, prices vary by large factors, but then so do the specifications. In the case of a feasibility study, prices should be within a tighter margin as the tenderers are all quoting against the same concept and specification. Why do these discrepancies occur? Price discrepancies will in every likelihood be attributed to two main factors; one, the perceived amount of work and two, the ability of the bidder to carry the risk associated with the feasibility study. It is, therefore, important that the scoping of the feasibility study covers the detailed requirements as clearly as possible stating what level of accuracy is required. The feasibility study is one of the first activities in the life of a project. The study, like the project it is investigating, is subject to the constraints of time, cost and quality. Its primary objectives are to demonstrate the viability of a project within the outlined scope and constraints.

Jan 1, 1998

By Ellson I. G

Shay Gap was created for the sincrular purpose of housing, in comfort, the workforce that would be required to mine iron ore, from leases held by Goldsworthy Mining Limited, in hill country, approximately 170 kilometres east of Port Hedland in the Pilbara region of Western Australia. To combat the and environment, the Company ultimately decided to adopt a novel planning concept for the town, which had not been attempted before in Western Australia. The special problems encountered during planning, and the reservations that were expressed during construction and early settle ment, are now part of the dim past. During the three years of occupation now achieved, there has been accumulated a story of success in the provision of an acceptable alternative to modern suburbia. Not only may this be claimed, but it can also be argued that the Shay Gap concept has been a more successful solution to a real environmental problem in our arid Pilbara region than has been seen in other similar settlements.

Jan 1, 1976