Search Documents

By K Karmawan, T Casten

The PT Freeport Indonesiaæs Deep Ore Zone (DOZ) copper deposit is located in the province of Irian-Jaya, Indonesia. Currently, a block cave mine is being developed around this deposit. Production is scheduled to start the fourth-quarter of year 2000 and to ramp up to 25 000 tpd by year 2003. The air quantity requirement for this mine is equal to 780 m3/s. To supply this quantity, the mine will require five centrifugal fans (one 450 and four 750 kW fans). This study summarises the technical aspects related to the installation and commissioning of two of these fans. The fans were installed on the surface in parallel arrangement with two others. Each has a design capacity of 240 m3/s of air at 2.2 kPa of static pressure. The study presents the installation details from the underground shaft excavation and portal development through fan testing and commissioning. It also presents the results of a monitoring system that was installed to determine the fan duties.

Jan 1, 2000

To finalise the arrangement and details of the headframe to be erected over the new No. 3 Shaft, the haulage and winding equipment requirements were first determined, then tentative designs were prepared to cover the needs of general shaft servicing work for men and materials, mullock and ore handling, and the probable requirements of a breaker station to be built adjacent to the headframe, which would provide for the crushing of the run-of-mine ore down to a size which would be suitable for feeding on to the concentrating mill.

Jan 1, 1957

The BHP Billiton Cannington mine uses sequential flotation to treat a silver, lead and zinc ore supplied from an underground mine. The final products from the process plant are a silver rich lead concentrate and a zinc concentrate. Operational history of plant performance highlighted that the majority of valuable metal losses to final tailing occurred in the -5 ¦m fraction. Research completed on the flotation characteristics of this size fraction in plant feed resulted in the development of a split flotation process to improve the silver and lead mineral recoveries. Construction of a $A 9.5 million brownfield project to install the new split flotation circuit at Cannington was completed in July 2002. The circuit consists of three stages of cyclone classification to recover the ultra fine material to a final cyclone overflow stream, conditioning of this pulp to achieve optimal process conditions, and conventional rougher and three stage cleaner flotation to produce a silver rich lead concentrate. The rougher tail from the new circuit is recombined with the cyclone underflow streams and processed through the original lead-zinc flotation circuit. This paper discusses the circuit design, material properties, material selection for components of the circuit, operational practices and requirements to ensure the circuit succeeded in meeting production targets. The technology is subject of a number of patent applications including international application No PCT/AU02/00400.

Jan 1, 2003

By Hein K. A A

The Mt Todd Gold Project is located 42 km northwest of the township of Katherine within the Northern Territory of Australia. It is situated in the southeastern portion of the Pine Creek Geosyncline. The Batman gold deposit, the largest of several deposits at Mt Todd, hosts an identified mineral resource of 92.9 million tonnes (Mt) grading 1.4 grams/tonne (g/t) as at 31 December 1993. Host rocks at Batman are assigned to the Early Proterozoic Burrell Creek Formation, comprising greywacke and siltstone interbedded with shale. Gold mineralisation is associated with a very broad zone of sheeted and stockwork quartz-sulphide veins that occupy a corridor of intense brittle fracture and faulting. A conceptual model of formation involves the dilation of joints and micro-faults within overlying sediments during sinistral movement along a basement shear zone. Synchronous granite intrusion generated convective circulation of crustal fluids through the sedimentary pile resulting in the formation of auriferous quartz veins within favourable structures. The Batman zone of mineralisation is not directly related to fold structures which typify several other major gold deposits within the Pine Creek Geosyncline.

Jan 1, 1994

By A Tolley

Bauxite residue or ‘red mud’ is a by-product of the Bayer Process, the primary process of alumina refining. Due to its high alkalinity and variable composition, its storage and disposal poses high environmental risks to water sources, surrounding ecosystems and human health. The high alkalinity (pH 12–13) is a significant factor in its classification as hazardous waste; to mitigate this, Australian refineries have integrated neutralisation processes into bauxite refining. Both sea water and carbon dioxide neutralisation processes are applicable. Multiple studies have demonstrated pH reduction from 12–13 to 7–10, depending on the method. The key advantages of CO2 neutralisation are that it allows for carbon sequestration and is more effective when utilised as a pre-treatment for recovery of metals, while sea water neutralisation is more established and has been integrated into two Australian refineries. This paper proposes the application of the bacteria Exiguobacterium oxidotolerans for bioleaching of iron from hematite in bauxite residue. The genus Exiguobacterium is characterised by its high levels of adaptability, halotolerance and alkaliphilic nature. E. oxidotolerans is successful at eluting Fe2+ from hematite via reductive dissolution, which complexes with oxalic acid produced during metabolism. This aquatic bacterium presents a novel process pathway for iron elution due to direct interaction of E. oxidotolerans with hematite via the cell membrane and operates within the pH range of neutralised red mud. The proposed mechanism is extracellular electron transfer, a microbial metabolic process where electron transfer is facilitated between bacterial cells and extracellular material. Currently this is being investigated for promotion of seaweed growth in coastal environments as soluble iron aids and fortifies colonies. This has potential downstream applications for cleaner iron and steel production. While theoretical, this paper explores the neutralisation, bioleaching and application of the Fe(II)- and Fe(III)-oxalate complexes formed.

Sep 18, 2023

By J Zhou, D M. Hunter, S M. Iveson, K P. Galvin

The recovery and concentration of ultra-fine iron ore can provide significant economic benefits. Presently, there are limited options available given the low settling rates achieved by conventional gravity separation and the relatively poor performance of reverse flotation. The Reflux Classifier is a new water-based gravity separation technology that consists of a set of parallel inclined channels positioned above a vertical fluidised section. This arrangement promotes a powerful throughput advantage compared to conventional fluidisation and a highly selective hydrodynamic basis for achieving sharp separations. A high shear rate develops within the inclined channels, which generates sufficient hydrodynamic lift to convey the lower-density particles (even if they are relatively coarse) to overflow while retaining the high-density particles (even those that are ultra-fine) for discharge to the underflow. The technology has previously been used around the world on particle sizes in excess of 0.1 mm. The present work, however, is concerned with density-based separations down to much finer particle sizes approaching 0.01 mm.A major advantage of the Reflux Classifier technology is the achievement of simultaneous gravity separation and desliming via a single-stage separation. A series of continuous experiments was conducted using an iron ore feed with head grade of 35 wt per cent FeT and nominal top size of 0.106 mm, with 59 wt per cent being below 0.038 mm in size. At a low throughput of 1.5 t/(m2 h), the Reflux Classifier produced high-grade products at a high recovery. For the entire feed, grades of 66.1 wt per cent FeT with Fe recoveries of 80 per cent were achieved in a single-stage separation. Within the 0.020–0.038 mm size fraction, grades of 68.8 per cent were achieved with iron recoveries of 94.7 per cent. Excellent recoveries of up to 57.0 per cent were achieved for the -0.020 mm size fraction. The ability of the inclined channels to retain the fine dense material further enhances the effectiveness of the Reflux Classifier by creating an autogenous dense medium effect within the vertical section. This helps to elevate large gangue particles up into the overflow.CITATION:Hunter, D M, Zhou, J, Iveson, S M and Galvin, K P, 2015. Gravity separation of ultra-fine iron ore in the reflux classifier, in Proceedings Iron Ore 2015, pp 143–148 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By Girnau G

The necessity of effective dust suppression measures during excavation work is just as uncontroversial in tunnelling as it is in mining. In many respects, in fact, the applied technology is comparable. Notwith- standing, given more careful appraisal, it becomes evident that very different starting conditions exist in both these fields: In mining, there are for instance, well organised firms, which in many cases have been active for several decades, carrying out the required drivage and winning operations - and although there are also experienced firms in tunnelling, these generally speaking form a joint venture in order to accomplish a certain project. These "tunnelling firms" which are formed for a short term, normally only exist for a period of two-to three years. They con- stantly reorganise themselves: from the site supervising engineers by way of the foremen and shift overseers to the gangs working on site. The "firm's headquarters" are also re- located when a new project is started up. Then of course, there is often pronounced fluctua- tion among the crews of a single tunnelling project. Seen from this point of view, a safety expert in tunnelling has a far more difficult task than one in mining. He has not the advantage of knowing every corner of the mine for years if not decades on end, of being familiar with the overall organisation of the enterprise let alone knowing many of the men at the face. This ideal prerequisite for effec- tive decisions pertaining to suitable measures for industrial safety and accident prevention taking all weaknesses into consideration given the interplay of the most varied system com- ponents, can practically only be arrived at in mining.

Jan 1, 1987

By Grieve BL

For a blast to be successful both heave and fragmentation must be satisfactory. Amongst the major factors influencing blasting are rock properties. This paper considers the effect of rock density on fragmentation and heave and how better results can be achieved in dense ore. Patterns which increase the heave and give better fragmentation are examined and the application of theory to the blasting of the Dales Gorge Haematite, density 4.2 - 4.5 t.m.,3 is then discussed. The drilling of staggered patterns instead of square patterns and a shallower 'V' initiation system has given better heave and fragmentation. This practice has re- duced backbreak and improved toe conditions; these factors have resulted in increased load ing rates. There has been an increase in the lump/fine ratio which is consistent with the theory although other factors such as ground conditions could have contributed.

Jan 1, 1978

By Chappell B

Backfill in the form of mine waste tailings has inherent problems associated with attaining adequate strengths upon placement. Fines are usually removed to ensure adequate drainage, which lowers the cohesive strength of the fill, leaving the fines to he placed in a tailings darn. Electro-drainage and electro-chemical grouting is examined to investigate its effects on densification and shear strength within a silty clay tailing having low permeability and shear strength. Two separate grouting mechanisms are observed for the iron and silica grouts used. Electro- osmosis is associated with iron grout that deposits within the tailing matrix under a converging pH gradient, and increases the permeability of the tailing. This process initiates cation exchange and causes cementing of the granular contact points between the clays. Electro-phoresis causes sodium silicate solution to deposit silica grout in the voids of the tailings. The resultant effect of these mechanisms results in an increase in cohesion, leaving the void ratio of the iron grouted tailings as it was but significantly reducing the void ratio of the silica grouted tailings.

Jan 1, 1998

By X Ma

Kaolinite is of very fine particle size in nature and thus its dispersion plays a key role in the successful removal of kaolinite in iron ore flotation and selective flocculation processes. As the most widely used dispersant in the world, sodium silicate has been used as a standard dispersant for kaolinite in the iron ore industry. However, the actual effect of sodium silicate on the colloid stability of kaolinite particles and its dispersion mechanism remain unknown in the literature. In this work, the dispersion effect and dispersion mechanisms of some common inorganic and organic dispersants, including sodium silicate, polyphosphate and a low molecular weight polyacrylic acid, on kaolinite particles were systematically investigated through electrophoretic mobility and colloidal stability studies over a wide pH range. It was found that sodium silicate-kaolinite interactions only take place in the neutral and acidic pH range, while polyacrylic acid and polyphosphate interact with kaolinite from pH 3 to 10.5. Consequently, sodium silicate only disperses kaolinite at neutral and acidic pH. In contrast, polyacrylic acid and polyphosphate disperse kaolinite from pH 3 to 10.5, with strong dispersion effect observed at neutral and acidic pH. In the iron ore industry, selective fl occulation and reverse cationic fl otation, the most widely used flotation route, are both conducted at pH 10 to 10.5. The results of the present study show that, at such high pH, polyacrylic acid and polyphosphate are more effective dispersants of kaolinite, in comparison with sodium silicate.

Jul 11, 2011

By Vink L, Johnson N. W, Mackenzie J, Young M. F, Johnston M, Landmark V

The influence of ore textures on metallurgical behaviour is poorly understood for most ores. An alternative method for characterising ore textures and for determining the resulting implications on ore processing has been developed for the Geor

Jan 1, 1998

By J J. Moreno, J Willis, P Garvey

Many of the tailings storage facilities (TSFs) in Australia are upstream raised facilities for which the consolidation of the hydraulically deposited tailings is essential to the stability of the TSF. While much operational consideration is given to limiting the rate of rise of TSFs through careful management of deposition rates to achieve desired consolidation, the rate of embankment raise construction (RoC) is often not given the same level of consideration. Loading the tailings at too high a rate during construction could lead to upstream and potentially downstream failure of the embankment. The Tailings Retention System (TRS) at the BHP Olympic Dam Mine comprises upstream raised TSFs that are continually raised with a zoned embankment. Improving on 20 years of successful embankment raising, there was a desire to understand the acceptable RoC under varying operating conditions and assess upper construction limits to improve operational risk management. To understand the RoC, trial embankment raise construction pads were constructed at different rates and the pore pressure response of the underlying tailings material was monitored. The pore pressure data were used to calibrate the permeability and consolidation characteristics of the tailings in a finite element model (FEM) that replicated a typical embankment raise. The rate of material placement, location of the phreatic surface and construction load were varied in the FEM until failure was initiated. The results were presented as a period (in days) over which the various zones for the embankment raise could be safely constructed. The results indicate direct sensitivity to the depth to the phreatic surface prior to commencement of an embankment raise, as well as the point of application of the construction traffic load. This paper presents the study approach, challenges experienced in modelling the construction methodology, the study results and their relevance in the improvement of understanding of RoC at the BHP Olympic Dam TRS.

Jul 1, 2021

By X Yu, Y Shen

The iron ore products should be assessed in terms of in-furnace behaviour and overall furnace performance, their operation should also be optimised under industry-scale blast furnace (BF) conditions, in order to be sustainable and competitive, especially in the context of decarbonisation efforts in ironmaking. While lab and pilot-scale experiments can provide useful kinetics, they are expensive and risky and cannot replicate industry-scale blast furnace conditions for proper assessment and optimisation. In this paper, we review our recent progress at Shen Lab of UNSW in using state-of-the-art Computational Fluid Dynamics (CFD) models to assess iron ore products and examine the effects of their operations on BF behaviour in basic terms, including in-furnace phenomena (flow field, temperature field, species distribution fields etc) and overall BF performance (coke rate, reduction efficiency and top gas temperature etc). We have developed state-of-the-edge CFD models for different purposes, ranging from the static-state BF model featuring unique layered burden structures for offline assessment and optimisation knowledge building-up for iron ore products, to the transient-state BF model for online assessment and optimisation of iron ore productions by describing the transient behaviours of iron ore productions under industry-scale conditions. First, we have studied several iron ore products including the iron ore products used in the present BFs and emerging iron ore products like carbon composite briquette and iron-coke. Second, several iron ore operations are studied including optimisation of conventional burden operations like oxygen enrichment, batch weight tuning and new operations like coke central charging and hydrogen injection in BFs. Third, some time-sensitive operations are also investigated including the use of wet burden materials and the drop in blast temperature on BF performance. These CFD models offer cost-effective research tools for understanding the effect of iron ore products on BF performance and serve as a reliable marketing tool for existing and emerging iron ore products under a wide range of BF conditions.

Sep 18, 2023

By C Samuelsson, Q Shu, A Lennartsson, F Gyakwaa, A Andersson, J Isaksson

The physico-chemical property, viscosity, is essential for pyrometallurgical processes and influences the settling rate of valuable metal droplets in slag, affecting the metal recovery. The copper slag from smelting furnaces typically contains between 1 and 2 wt per cent Cu, which equals to or is higher than in most sulfidic copper ores mined today, meaning the slag is a valuable resource for copper extraction. A low viscosity is desirable for slag-cleaning through a settling furnace where entrained droplets settle under gravity. One approach to control the viscosity is through the slag composition. The literature has limited data on the correlation between viscosity, slag structure, and optical basicity of iron silicate slag with FeO/SiO2, CaO, and Al2O3 as factors. Therefore, the present study evaluated the influence of these factors on viscosity and correlations with slag structure and optical basicity. The FeO/SiO2 ratio (at%/at%) and the CaO and Al2O3 content were altered in two levels, resulting in a two-level full factorial design with three factors. The study was done by synthesising FeO–SiO2–Al2O3–CaO–MgO–Cr2O3 melts, followed by water granulation. The melt structure of the samples was analysed with the help of Raman Spectroscopy. The viscosity was then estimated with a high-temperature rheometer using a Mo spindle and crucible. The results showed a correlation between the optical basicity, FeO/SiO2 ratio, and viscosity, where a high optical basicity and FeO/SiO2 ratio were beneficial for achieving a low melt viscosity.

Jun 19, 2024

By A Scott, S Kanchibotla, J Segui

The æMine to MillÆ concept is not new. In fact, it is the underlying objective of every mine. Unfortunately, in many operations the management structure and reporting systems have created independent æbusinessesÆ within the overall mining enterprise. This has created incentives to optimise the performance of each component of the operation rather than the enterprise as a whole. The Mine to Mill Conference organised by The AusIMM in October 1998 documented a number of case studies where run of mine ore was not presented to the mill in the best possible form for subsequent stages of comminution and processing. A number of examples were quoted where modest expenditure in the mine had a very significant impact on downstream process efficiency and hence costs. Examples included:the minimisation of fines in the mining and handling of iron ore; the management of fines in blasting and crushing for a copper heap leach operation; the control of blast damage, mining recovery and dilution in open cut coal operations; and the optimisation of mine fragmentation to increase mill throughput in gold and copper operations. The latter topic has been trialed at a number of mines and is referred to as æMine to MillÆ fragmentation. A number of æMine to MillÆ type investigations have been reported in the literature including Pease et al, Simkus and Dance, Nielsen, Scott et al, Kojovic et al, Kanchibotla et al, Bulow et al and Hawkes from the 1998 Mine to Mill Conference. In addition, a number of studies are in progress or the results have yet to be published. These studies have demonstrated the feasibility of obtaining the data required to characterise the breakage behaviour of ores and to model the impact of changes to blasting practices on process efficiency. Characterising the breakage behaviour of ores is a vital step in the management of fragmentation and comminution in mines. The characteristics of importance to fragmentation fall outside the parameters conventionally required to describe the economic geology of a deposit. æMine to MillÆ optimisation of fragmentation means that the mining engineer needs information from the geologist in order to be able to help the metallurgist. Providing this information requires close interaction between these groups.

Jan 1, 2000

By I R. F MacCulloch, K Jones

Pintail Systems, Inc, a Colorado USA based company has developed and commercially applied bioremediation processes for biological detoxification of cyanide compounds in mine waste. Site-specific microorganisms are isolated from spent ore, tailings or process solutions and augmented in the laboratory for cyanide oxidation, denitrification and metal biomineralisation. Biological processes typically treat complex contaminants (cyanide compounds, soluble metals and nitrates) in a fraction of the time of conventional remediation processes. Cyanide is used in microbial metabolic processes as a carbon or a nitrogen source. Biological detoxification processes applied at the end of mine life can end long-term liability and perpetual monitoring and containment. Case studies from commercial application and demonstration programs for the US Environmental Protection Agency will be presented in this paper.

Jan 1, 2004

By Davies H, Pigram C, Sunata W, Falvey D, Loxton C, Giddings J, Rogerson R

PALAEOMAGNETIC CONSTRAINTS ON TERRANE TECTONICS IN NEW GUINEA Chris Klootwijkl), John Giddingsl), Wahyu Sunata2), Chris Pigraml), Charles Loxton3), Hugh Daviesl), Rick Rogerson3) and David Falveyl) 1) Bureau of Mineral Resources, Canberra, Australia 2) Geological Research and Development Centre, Bandung, Indonesia 3) Geological Survey of Papua New Guinea, Port Moresby, Papua New Guinea

Jan 1, 1987

By M Scoble

This paper is based upon the experiences of collaborating academics in two mining schools and their personal view of attempts to integrate the principles of sustainable development into mining education and research. In this quest, the concept of sustainable mining practices is proposed, not only relating to environmental, social and economic performance but also stressing mine safety and efficiency. These practices need to support strategies that enable flexibility and resilience within mine operations to counter recessionary cycles. Also, these counter-cyclical strategies are now imperative for sustaining mining education and research itself. There is a critical interdependence between these two different perspectives on æsustainabilityÆ. The paper concludes by demonstrating models of strategies that promote inter-disciplinarity, collaboration and networking for sustaining mining schools.

Jan 1, 2009

By MacDonald AJ, Raffield MP

The South Deep massive orebody consists of 20 to 30 in of payable conglomerates ranging in dip from 11¦ to 20¦ and at depths of between 2400 in and 34(10 in. The mine design process selected a mining method with a proven record of application that could be adapted to overcome the inherent difficulties associated with the depth, thickness and structural influences of the South Deep orebody. A modified cut and fill mining method provides a concentrated and highly flexible method of extraction. An integrated destressing cut will enable the modification of the stress environment such that it is suitable for massive mining operations. The choice of backfill type and stoping width in the destressing cut ultimately determines the characteristics of the stress modification and, as such, is critical to the success of the cut and fill operation. This paper discusses the decision process undertaken to determine the optimum backfill type and stoping width combination in terms of, conditions in the destressing cut faces and in the massive mining environment. Numerical modelling has been extensively used to analyse arious scenarios to aid in the decision process.

Jan 1, 1998

By Jaques A. L, Heinrich C. A

Mt Todd lies towards the south end of the Pine Creek Geosyncline, sandwiched between the Cullen Batholith and the Edith Falls Basin, in an area of regionally metamorphosed sandstones, siltstones and shales. The Batman deposit, some 3 km west of Mt Todd is a sheeted quartz vein system hosted within greywackes of the Palaeoproterozoic Burrell Creek Formation (Finniss River Group). The gold-bearing quartz veins, trending 010¦-020¦ and dipping 60¦-70¦E, are commonly 0.5 to 5 cm wide and occur at intervals which are from 10 cm to 1 m apart. Gold tends to be restricted to the quartz veinlets and immediately adjacent country rock. Grade Control utilises two 4 m 'collar' samples which are collected from each 8 m production blasthole. The irregular distribution of the quartz veins and erratic gold mineralisation has resulted in a disseminated 'salt and pepper' type of gold occurrence, with only a poorly defined footwall. Delineation of ore and waste blocks for mining uses an approach which combines the smoothing effect of kriging with a pragmatic view of the raw data. Large ore blocks with simple geometry help to minimise mining dilution, reduce block variance and give good reconciliations to interpreted ore tonnes and grade. Daily mine face advance is reported against truck counts and provides continual comparison with budgeted production. All data processing uses Gemcom software, together with Lotus spreadsheets.

Jan 1, 1994