Search Documents

By K Ehrig, V Liebezeit, Y Li, B Pewkliang, M Smith, E Macmillan

Pre-concentration of low grade ores via the rejection of low/no value materials based on fragment size is the subject of many published papers and studies over the past decade. However, the possibility of upgrading should not limited to low grade ores given the high cost of capital, energy, water, reagents, and ultimately tailings storage across the mining industry. Mining and processing facilities at Olympic Dam consist of an: 1) underground mine where ore is extracted via sublevel open stoping and 2) integrated processing plant located on the surface which produces Cu-cathode, Au-Ag bullion and uranium oxide concentrate. Blasted ore is trucked/trained to underground crushers which produce an ore feed with a product size P80 = -145 mm. Crushed ore is then hoisted to the surface and delivered to the ROM pads via an overland conveyor. The typical copper grade of mill feed is approximately 2 wt%. A rapid assessment of the potential to upgrade Olympic Dam mill feed prior to the ROM pads via rejection of low value materials based on fragment size was completed using existing data. Three separate datasets were utilised to assess the deportment of Cu, U, Au across size ranges of 200 mm down to sub-8 m. Cumulative grade vs cumulative mass distribution graphs for each element were produced. This data clearly demonstrates that Cu, U, Au grades remain constant down to ~212 m, which happens to be the liberation size of the sulfides. Hence, no potential to upgrade the ore stream via rejection of +200 mm - to ~212 m sized materials prior to milling. Mineralisation within the Olympic Dam Fe-oxide Cu-U-Au-Ag deposit (IOCG) occurs as disseminated sulfide grains within granite- to hematite-rich breccias. The typical sulfide grain size is sub-200 m that supports the outcomes of the grade deportment by fragment size study.

Nov 10, 2020

By P Valenzuela

Joint mapping is a fundamental input for rock mass characterisation and slope stability analysis. The usual way to do it is using a compass in the field or digitising structures on a screen, with a software package.In this paper a method to identify and map joints automatically along a rock face is presented; it is called the Concentric Shells (CS) algorithm. The method scans a point cloud sequentially, tests if selected points are ‘true pivots’ within an inner shell, and then it searches for points inside a wider sphere (outer shell).The algorithm, developed by the author, was applied in real data. It reproduces the main features obtained from conventional (compass) and digital mapping (software package). Execution times are approximately 45 seconds for two point sets holding of 3.1 million points. Obtaining the same results via digital mapping takes approximately 3–4 working days.Key advantages of this method are: significant time reductions; elimination of mapping bias; and the ability to manage very large data sets (>2 million points) without the need of scanning the cloud on the screen. These advantages make this method an attractive tool for engineers and geologists wanting to increase productivity.CITATION:Valenzuela, P, 2017. Automated joint mapping using the concentric shells algorithm, in Proceedings Tenth International Mining Geology Conference 2017, pp 257–262 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

By J Y. C Lo

The construction of two drainage tunnels and the associated subvertical drain system at the Po Shan area in Hong Kong was completed in December 2009. This project is the first of its kind to utilise drainage tunnels and a network of subvertical drains to regulate the groundwater table to enhance the long-term stability of the hillside of Po Shan area.The groundwater levels, monitored by preinstalled piezometers, once exhibited dramatic drops during drilling of the subvertical drains; however, have recovered from natural replenishment after effectively plugging of the drains. The level of groundwater drawdown is in line with the design function of the subvertical drains. In order to understand the groundwater flow pattern in the Po Shan area during and after construction and to set out operation schemes for the subvertical drain system so as to control the groundwater table in the Po Shan area, a post-construction review has been carried out to examine the behaviour of the drainage system and its impact on the surrounding subsurface groundwater flow.This paper presents a review of the groundwater monitoring data during and after the construction of the drainage tunnel system covering a period of over 3.5 years. A simplified conceptual hydrological model is developed, which has been verified by the monitoring data, to capture the key elements with regard to groundwater variations in different stages of the construction. The performance of the tunnel and subvertical drain system as revealed from these field measurements is discussed.

Mar 8, 2011

This paper documents the relationship between material handling and processing costs compared to blasting cost. The old adage, 'The cheapest crushing is done in the pit', appears accurate in this case study. Comparison of the accumulated cost of powder, selected wear materials and electricity, indicate a strong, inverse correlation with powder factor (lbs powder/long ton of rock). In this case, the increased powder cost is more than offset by electrical savings alone. Measurable, overall costs decline while shovel and crusher productivity rise by about five per cent when powder factor rises by 15 per cent. These trends were previously masked by the effects of weather, ore grade fluctuations and accounting practices.

Jan 1, 1995

By Blair J. R, Barrett J. R

In many underground mining applications where-dry fill is used, only a token acknowl- edgement of the fill properties is given. It is the aim of this paper to induce mining engineers to consider dry fill as an engineer- ing material rather than a mass to place in unwanted voids. Dry fill is generally cheap, inert and readily available, but it can still contribute to mining performance. In particular, the choice of the dry fill becomes more critical as stope sizes increase, controlled choked draws are used or pillar recovery introduced. Selection must be initiated from an evaluation of the role of the fill in the mining operation. In most cases the fill must be chosen before quarrying begins and an investigation must be made of available sources and appropriate quarrying methods. Some of the properties of fill are described together with evaluation techniques. A com- parison of placement conditions is limited by the complexities of material flow and degrada- tion: However, field and model tests can aid interpretation in these cases. Examples are given of aspects of dry fill selection and their incorporation in mining design.

Jan 1, 1973

By Boehme PW, Gregory OR

The results presented here show quite definitely that in the system investigated the intensity of dispersion is enhanced by switching the flow entry from bottom to sides of the packed trough. Since there is no reason to suppose that this would not be true generally then it is not surprising that the blast furnace dispersion data of Standish and Polthier lie above the data for packed columns with bottom fluid entry. In fact, on the basis of the present results, blast furnace dispersion results can never equal standard packed column behaviour but must always be above these. The result that the intensity of dispersion in the trough model is higher closer to the side ports than away from them is at variance with that of Standish and Polthier blast furnace results. Aside from the obvious structural differences between these two systems, it is thought that the presence of raceways and the tortuous path of the gas flow in the furnace may provide an answer. Clearly this is an important difference in the behaviour of the two systems and further investigations designed to clarify the position would have significant practical value. This would also give an indication of how the furnace D/ud values may be decreased along the whole height - assuming of course that this result gives the best overall performance of the furnace. However, there is to date no knowledge whatsoever about this aspect of blast furnace Technology.

Jan 1, 1975

Since the 1950's drilling has been rapidly mechanised. First from hand held drills with air legs to pneumatic jumbos, then to more effective hydraulic jumbos. Development of underground drilling equipment naturally could not have stopped here. Hydraulic drilling saw an improvement in drilling capacity and efficiency after the introduction of second generation drifters in the early 1980's. Also in the early 1980's a few equipment suppliers started to study how to improve the efficiency in operating the rigs. The first computerised rigs for tunnelling were delivered to work sites in mid 1980's. At the same time a few computerised longhole drills started drilling in mines.

Jan 1, 1988

It is difficult with inadvertent explosions to establish fundamental data, especially of original dust, of pressure, temperature etc. and of ventilation oscillations, as exposed personnel rarely survive. Retrospective data from explosions must be derived from damage, from fatalities, from ventilation analyses, from analyses of dusts and other indications of temp- erature and duration of temperature. The five disastrous explosions selected for analysis provide examples of what data can be established as to the cause and extent of explosions. Such information is required for legal etc., inquiries subsequent to explosions, but most importantly to give the best guidance for avoidance of possibility of further Disasters.

Jan 1, 1981

Australia as a leading producer of mineral sands has also occupied a leading position in many areas of research'in the processing and applications of these minerals. Research in upgrading ilmenite to produce synthetic rutile has resulted in the develop- ment of many processes, e.g,., Becher, Murso, Chlorine Technology, and ICI processes. Studies on the reducibility of ilmenites, aqueous leaching of reduced ilmenites, Fe-Ti-O system, leachability of natural and treated ilmenites in hydrochloric acid and selective chlorination of iron from ilmenites have been carried out in order to develop and improve the efficiency of the above processes. While research on the processing of zircon sand to produce high purity (99.99% ZrO2 zirconia powder and zirconium chemicals started only recently, research by CSIRO in the early 1970s led to the discovery of the phenomenon of transformation toughening in partially stabilized zirconia (PSZ) ceramics. Australia, with very significant resources of lanthanide-containing ores, pro- duces substantial quantities of monazite each year but research in processing and appli- cations of rare earths was neglected in recent years in this country. However, research to improve processes for the recovery of rare earths is now under way and studies on the production and testing of Nd-B-Fe magnets which are 1.5-2 times stronger than the strongest magnets (Sm-Co) currently available, have also commenced.' An overview of the research in the pro- cessing and applications of mineral sands during the last two decades in Australia and its implications for the industry are pre- sented in the paper.

Jan 1, 1986

By Beamish B. B

In this study, a systematic examination of the scale and variety of micro-structures in coal using Scanning Electron Microscopy (SEM) has been carried out, using coal samples of differing stages of coalification from the Bowen Basin and New Zealand. SEM provides detail of various micro-structural features and shows that a variety of micron-sized fractures and cavities are present in coals. These are differentiated into three pore types: fracture porosity, phyteral porosity and matrix porosity. Fracture porosity is generally associated with bright coals (although it has been shown that micro-fractures are present in maceral fragments from the dull coal layers). Characteristically the macro- and micro- fractures form a continuous structural fabric through the bright coal layers and thus make a significant contribution to overall permeability. The macro- and micro-fractures appear to have been formed during the process of coalification rather than being formed due to shrinkage during methane extraction, as most of them are infilled with secondary minerals. In contrast, phyteral and matrix porosity is associated with the dull coal layers that are composed of plant fragments or a heterogeneous mixture of macerals. Like the macro- and micro-fractures, the continuity of the observed cavities suggest that these too are a significant contribution to overall permeability, and therefore play a major role in the transmissibility of methane at a level between diffusion at the micropore level and laminar flow at the macro-fracture level. Due to different spacing, orientation and persistence of individual fractures and cavities, the rate of methane transmissibility through a coalseam will vary according to coal rank, coal type and the organic precursors from which the coal was derived. This is important as a knowledge of the micro-structure system and its relationship to coal type and coal rank, plays an important consideration in: a) gas drainage modelling, b) enhancing permeability by inducing fractures and c) predicting the occurrence of outbursts.

Jan 1, 1991

By Misk A

Several logging methods are presently available to the oil industry for the evaluation of formation porosity: the Sonic and Neutron logs are already widely used, the Gamma-Ganmia log is being progressively introduced. The readings of these instruments are primarily a function of the rack-porosity, hence the general term of "porosity tools". Apart from porosity, however, other variables such as type of fluid in the pores, nature of matrix and degree of shaliness have an important influence.The response of each device is a different function of such parameters: therefore, a cci bination of porosity tools can lead to information on these variables in addition to the evaluation of effective porosity.For example, the presence of gas; rather than water or oil, in a formation which is not deeply invaded, will tend to give Neutron derived porosity values which are too 'low; on the other hand, the Sonic derived porosity: value will be too high in such- a case. For the same porosity, the Sonic gives a longer transit time in sandstone than limestone, whereas in the low porosity range, the Neutron will read more counts per second in a sandstone than in a limestone of the same porosity. The presence of shale also affects the readings of the various porosity tools in different ways so that the combination of two or more methods may lead, in some cases; to an evaluation of both the-effective porosity and the shale, content.In conclusion, it may be said that the various porosity tools pre-sently available, are, to a large extent, complementary, and that in many problems the use of two porosity tools, instead of one, is very likely to bring valuable additional information.

Jan 1, 1962

By S Grant, S Emeric, P Baker, E Jones, D Clark

As we strive for a sustainable and resilient future, repurposing assets has become a top priority. In Australia alone, we have a significant number of mineral projects in the pipeline, extensive existing operations, and over 50 000 legacy sites. Collectively, this presents a unique opportunity to be a world leader in mine rehabilitation. Complex stakeholder landscapes, inflexible policies, aged regulatory frameworks, technical uncertainties and increasing liabilities are all barriers hindering effective transition of legacy assets. The impetus for change is further catalysed by shifting consumer preferences, workforces in flux and regional Australians questioning what the transition means for their local community. We need innovative approaches to take a leading role in the industry and support global efforts more broadly. Co-designing an ambitious, shared vision spanning projects, operations and legacy assets with all key parties is a fundamental step to unlock and realise maximum societal, environmental, economic and reputational value. Serious play and gamification can further enhance this visioning process.

Aug 2, 2023

By Jarvis ST

Colliery spoil is the major constituent of colliery spoil 'rockpaste' which has been used to infill abandoned limestone mines in the West Midlands of England since the early-1980s. The other constituents of rockpasle are pulverised fuel ash, lime and water. A key property of the rockpaste is its ability to flow within the mine workings over considerable distances before setting. This paper describes the work carried out to identify suitable sites as sources of colliery spoil for making rockpaste and goes onto consider the flow properties of the material and the monitoring methods used on-site. A full-scale trial comprising mulling a 6600 nt' section of an abandoned mine was conducted prior to the mulling of the Littleton Street Mine which had a volume of about 500 000 m'. As well as describing the methods used for monitoring the movement of rockpaste material, a description is also given of a dip-meter developed specifically for the purpose of measuring the level of paste in the mine. This paper shows how a colliery spoil based paste has been successfully rued for infilling abandoned mine workings. The monitoring systems developed for use in the two case studies presented in this paper are now being used extensively for infilling other abandoned mine workings. To-date over I I mines with a total volume exceeding two million cubic metres have been backfilled.

Jan 1, 1998

By W J. Shaw

Mining operations must become more predictable to overcome the volatility that has characterised the mining industry. Comparisons of production against predictions will become more consistent as mining operations merge and expand, as personnel move from site to site, and as public reporting of reconciliations becomes more prevalent. More consistent approaches are already being seen in the industry using the terminology used in this paper and elsewhere.Examples are provided that show how use of the waterfall chart as a reconciliation management tool can provide objective analysis to improve practices.Geometallurgical modelling is becoming more useful and will continue to do so as we move from a few bulk samples to better interpretation of material properties from geological mapping and drill sampling. Reconciliation has evolved to the stage where predictions of geometallurgical properties to optimise mill performance, and of geotechnical properties derived from better 3D geological models, should also be reconciled.CITATION:Shaw, W J, 2014. Reconciliation – outcomes and expectations, in Proceedings Ninth International Mining Geology Conference 2014 , pp 123–128 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 18, 2014

By Sturchio NC, Williams SN, Fischer TP

Chemical and isotopic analyses of fumarole gases from Galeras Volcano, Colombia provide significant insights into the origin of volatile components in the magma.. Water comprises a mixture of magmatic (rock-equilibrated at high temperature) and meteoric, with the relative proportions varying through time. Carbon isotopes are most consistent with a mantle source, although other contributions to the system cannot be ruled out. Nitrogen most likely originated from organic matter in subducted oceanic sediments. All of these "primary" components have been modified somewhat by interaction or exchange with other reservoirs during ascent to the surface. In addition to information on the origin of the gases, these data show significant temporal variations precursory to eruptive events. Chemical ratios change and water becomes more meteoric in character prior to eruptions.

Jan 1, 1995

Last September, when I was asked to prepare this paper, I was told the subject was "mining," a broad subject indeed! Rather than choose one of the many important technical and economic details which characterize mining today, I turned to a subject which fas- cinates me: mining's image. If we are to survive and prosper into the twenty-first century, and if industry and society are to continue enjoying the material benefits which flow from mining, we must address the melancholy fact that the general public at best does not understand mining, and at worst does not believe it is needed or deserves to continue. While my point of view is largely that of an American mining executive, I would hasten to point out that Homestake has participated in Australian mining for over three decades, and our subsidiary, Homestake Gold of Australia Limited, is now a major producer in this "lucky country." Does society need a viable minerals and metals industry? The answer is obviously "yes," so the challenge is to change some minds: not just those of the amorphous "public," but on a focussed basis targeting journalists, educators, TV commentators, politicians and opinion makers of all stripes (I thought of using "rifle shot" instead of focussed but thought that might be misconstrued). Along the way we miners must also look deeply into ourselves, our attitudes towards the society in which we function, and our willing- ness to change as well as to seek change in others. How did we become such bad guys? More than a century ago mining was not just accepted, it was even romanticised. In America, we had altered the time-honored concept of "Crown" lands into public lands made easily available to settlers pushing back the frontier. Miners even preceded the farmers and stockmen in what was perceived as nation-building, although by the 1890s there was a growing interest in conservation, especially the protection and management of forests and national parks. Even though emphasis was shifting toward government stewardship and away from trans- fer of public lands to private ownership, homesteading and mining were clearly recognised as valid uses requiring not just access, but security of tenure. Indeed, conservation as it was then understood implied management of the public domain as well as its protection. Initially this was no great problem to the U.S. mining industry, but as the nation grew and competing land uses became more important, conflicts began to appear, first over water rights and later over air quality and destructive mining practices. But these were local disputes rather than national issues, and two World Wars, the Great Depression and post-war reconstruction lulled our industry into thinking that nothing had really changed. After the storm began to break in the 1960s, the mining industry found itself confronted by a growing maze of complex and costly laws and regulations. It took us longer than it should have to realise that, in facing this challenge, we seemed to have lost the understanding and support of many of our legislators and a majority of the general public. For over 20 years now, since the first Earth Day in 1970, the U.S. Mining

Jan 1, 1991

By Dunlop JSF

A description of general mining proced- ures and tyre maintenance practice is given with particular reference to tyre mainten- ance facilities and record keeping at Groote Eylandt. Experience with tyre wear on Wabco 85C rear dump trucks is then outlined, concen- trating on wheel camber, wheel alignment, truck speed, tyre pressure, loading and haul road design. T T.1TUnilhTPTTnAT The Groote Eylandt Mining Company Pty. Limited mines and beneficiates sedimentary manganese ores from a series of orebodies occurring in the western part of the island. The island is one of a group on the western side of the Gulf of Carpentaria, about 50 kilometres from the Arnhem Land coast and about 650 kilometres from Darwin. Whilst capacity of the mine is presently 2.3 mil- lion tonnes of product per annum, current production has been reduced to just more than half this figure, due to a general mar- ket recession.

Jan 1, 1982

Most orebodies have one or more boundaries which are gradational, where the decision to stop mining is based on an economic cut-off. To maximise profit, this cut-off grade must be chosen correctly. It is necessary to review cut-off grades regularly, as the optimum cut-off grade changes with time, and major changes are hard to implement in a working mine without disruption to production schedules.Whenever a cut-off grade is used, there will be errors in its application caused by errors in the estimation of block grade. These can be minimised by stringent quality control in sampling and by the use of kriging, which attempts to minimise the absolute errors in grade estimation. The kriging method used should produce the most accurate estimates of marginal grade blocks - this will not necessarily be the technique that gives the best overall prediction of head grades.

Jan 1, 1993

With the advent of the mini computer and the relational database project management has experienced a new lease of life. The project manager no longer has to wait days for his reports, and he doesn't have to thumb through a foot of four part stationery to find that one line of information. The new techniques bring characteristics that are music to the ear of the project team giving them a better chance of bringing the projects in on time and within budget.

Jan 1, 1983

Visual computing opens the design process to a wider audience and allows rapid communication of mine plans to all stakeholders. The integration of software and hardware technologies that take advantage of a graphical environment will continue to improve both long-term and short-term mine design (Figure 1). A good design must be adaptive to respond to decision changes as the mine develops and more information becomes available. The constraints on mine design predicate careful analysis in order to operate the mine as efficiently and safely as possible.Continuous improvement in mining is assured by developing innovative technologies that target mine survey, drill and blast, modelling, short-term design and pit and stope optimisers. The design life of a mine has to be sufficiently long to ensure the mine is commercially successful, justifying the high start-up capital costs. Being able to execute a plan so that it honours the design realises the rewards of computerised mine planning and the long-term investment in data acquisition.

Sep 26, 2011