Search Documents

By L Nienaber

Mines, after becoming operational, often retain the same support and reinforcement designs developed in the feasibility study. These designs are conceived from limited drilling data and regional experience, thus having an empirical flavour. Empirical designs are perceived to be conservative, catering for a variety of failure mechanisms, which are not always present in mine development drives.This begs the question: If you were to invest in the necessary resources to obtain sufficient data and complete the required analyses for the different development drives in the mine, to engineer a support and reinforcement scheme with the capacity to match the demand of the rock mass, what is the difference in cost when comparing an empirical design to an engineered design?To answer this question, mine tunnels with different geometries and orientations, where detailed structural data was available, were selected for a comparative design exercise. Material cost, development cost, cycle time and professional fees for engineered and empirical designs were estimated. The outcome is summarised in the following paper that discusses the process followed and the results of the design comparison.

Mar 8, 2011

By A Penney, M J. Pascoe, R M. Stephenson

The empirical McCracken and Stacey stability and risk assessment method has been in use for more than 20 years to assess geotechnical stability issues for raise bored shafts. The methodology has been applied with various levels of success. Increasingly, trends in mining and civil tunnelling have been towards larger diameter, single pass, raise bored shafts to rapidly provide means of ventilation, material movement (ore passes), or emergency egress. Identifying and assessing potentially problematic zones before raise boring commences can allow for appropriate risk-based decisions on construction, or to investigate alternative solutions. The implementation of a proactive solution to raising through an identified weak zone is preferred to the application of an engineered solution to an area subjected to substantial instability or failure. Methods for investigating potentially problematic areas are discussed in this paper based on AMC’s benchmarking data. Proactive investigation programmes resulting from these investigations are also discussed. Previous publications discussing the benchmarking data have concentrated on Australian case studies. Increased efforts and recent updates have been made to expand the database to include international case studies. This has provided further refinement of lower bound ‘raise bore rock quality index’ (QR) values, and various rock mass parameters for stability assessments. CITATION:Penney, A, Stephenson, R M and Pascoe, M J, 2018. Raise bore stability and risk assessment empirical database update, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 434–445 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By N Anderson

With traditional grade control processes, geological models are created by geologists at the completion of the data collection stage and wireframe construction is closed off at a set date to allow for time to complete the estimation process. Any issues identified at earlier stages or the addition of new data requires the estimation process to be started again. Alternative interpretations are explored only if time allows and often in a limited fashion. An alternative workflow has been developed at the Waihi Underground Gold Mine utilising Leapfrog Edge and Seequent Central. Geological and grade control models are created, dynamically linked, and saved as separate branches. A project geologist is able to work on the grade control model and a mine geologist on the geological model simultaneously. This allows for a non-linear modelling workflow with continual review and feedback. The introduction of new data can occur right up to the model due date, with data collection, validation, alternate interpretation, and review happening incrementally. Models are categorised and stored in Seequent Central according to project status. An approved version of the geological model and grade control estimate are uploaded at the time of release and transparently capture all data used at a point in time, as well as the review process. Dynamically updating models for grade control has reduced turnaround time while increasing accuracy and quality. Estimates of individual domains are vastly improved from being able to rapidly evaluate the effects of model parameter changes in real time and 3D. Development and stope design directly benefit from these streamlined processes, with higher quality, timely production occurring as a result.

Mar 22, 2022

By Neill T. J, Howarth D. F, Malcolm J. McPhersqn

For many years Isa Mine has seen the need for a continuous mining machine which will economically cut hard rock. Tunnel borers are unsuitable due to the size and inflexibility of the machine and the shape of excavation mined. The design of roadheader type machines will not permit the use of the necessary cutting technology. in 1983 a joint project was undertaken by The Robbins Company and Mount Isa Mines Limited to develop and to trial a machine suitable for cutting hard rock in an operating mine. The project was based on the proven technology of raiseboring applied to horizontal development. The Mobile Miner was fabricated and trialled in a disused quarry in the U.S.A. during early 1984. Following these trials, the machine was transported to Mount Isa and commenced mining in September that year. The initial duty was to continue the development of a decline commenced by conventional mining for a conveyor system to serve the deeper southern areas of the 1100 copper orebody. This system will permit direct tipping of copper ore to a new crusher complex and conveying of the - crushed ore approximately 2 kilometres to the central hoisting shaft facilities. The Robbins Mobile Miner MM120-3001 uses a vertical rotating cutting wheel mounted on a horizontal swinging boom to excavate a nominally rectangular shaped heading. The cuttings are collected on an apron and conveyed back through the machine. The resulting excavation is smooth-walled with no blasting damage to the surrounding rock. This provides a safer working environment than does conventional drill and blast development mining. Ground support requirements are considerably reduced.

Jan 1, 1986

By Marton A

The Readymix Group have a Quarry Improvement Program - 'Building in Quality (BIQ) which has many parallels to the ICI Explosives' total quality management - 'Quality Improvement Program' (QIP). Both companies have for some time recognised that the 'do it right first time' principle means less wasted effort and materials, that efficiency breeds profitability and so actively promote the quality culture. To install the principles and generate the culture requires considerable commitment and effort from the top down and invariably spreads to the suppliers and sub-contractors. Understanding the component processes involved with the quarry operation, analysis of those processes and gaining a breakdown of the cost of non conformance then allows the astute quarry operator to make the necessary changes to improve the process to realise profits. This paper outlines the steps in such a process and the profitable outcomes of the commitment to continuous improvement at the Nickol Bay Quarry.

Jan 1, 1994

By A G. Guinea

If you were reading this article in a newspaper or similar in the 1800s, you would know that the world was firmly in the grip of the Industrial Revolution. You might have been one of the families that decided that an agriculturally based existence was no longer for you, and that the promise of a factory job was more appealing and more secure. And it was. Financially at least. Not so much from a workplace safety perspective.

May 5, 2022

By J R. Ruiseco, D La Rosa, L Julian, W Hunt

The DeGrussa copper-gold deposit is located 900 km North of Perth. Copper-gold bearing massive sulfide lenses occur in lower greenschist facies meta-sedimentary and mafic volcanics of the Bryah Basin. Regional folding, faulting, and tilting of the stratigraphy primarily occurred during the Capricorn Orogen (Johnson, 2013). The Shiraz Fault and Merlot Fault are regional oblique-sinistral faults that offset the DeGrussa massive sulfides lenses into three fault blocks by ~350 m and ~120 m, respectively. A network of deposit-scale brittle-ductile faults splay from, and in one example are cut by, the Shiraz and Merlot faults. This results in localised ore displacement, selvage alteration and degradation of the rock mass integrity. Historically, only the Shiraz and Merlot Faults were modelled and validated during mining and grade control. The requirement for a comprehensive structural model became more relevant as mining became advanced and confining stresses on local rock mass became more complicated. The DeGrussa Structural Model has been developed to delineate areas of structural complexity and is an important tool in mitigating rockfall risk through well informed technical design. During this process, every accessible excavation was walked and structurally mapped. New workflows in Leapfrog Geo and new technology, including an app that runs on mobile phones streamlined the validation process. Drill hole orientation was a limiting factor during validation. At the time of writing this submission, the DeGrussa Structural Model consists of 34 faults, and is now an important tool for the Technical Service team when developing mine plans and schedules. Applied structural geology is often seen as exclusive to those with a PhD in the field. Faults at DeGrussa have been modelled and reconciled by a Mine Geologist and Geotechnical Engineer, using first principles geological characterisation. This is a simple process that demonstrates any geologist can contribute to a structural model, provided they understand the fundamentals of unbiased structural measurements and consistent record of observation

Mar 22, 2022

By M Norbert, C Bennett

The Legacy Way Tunnel was constructed from Toowong to Kelvin Grove in Brisbane, and is the first large-scale underground excavation in the Bunya Phyllite in Brisbane. The Legacy Way Tunnel is 4.3 km in length, comprising two mainline tunnels excavated by a tunnel boring machine (TBM) with 46 connecting passages excavated between the mainline tunnels for egress provision and services. The Legacy Way Tunnel passes through two geological formations, the Bunya Phyllite and the Neranleigh Fernvale Beds. The Bunya Phyllite is the dominant formation of the Legacy Way Tunnel, extending for three quarters of the tunnel prior to intersecting the Normanby Fault Zone (NFZ) and the Neranleigh Fernvale Beds. The NFZ forms the contact between the two formations as part of the Brisbane Metamorphics, which underlies the majority of Brisbane City. The development of the geological model and the understanding of the ground’s reaction to tunnelling was an iterative process. The tender phase investigation data has been supplemented with additional design phase investigation boreholes, geophysics and walk overs. Aerial photograph interpretation coupled with borehole data allowed the development of the domains along the length of the tunnel. Early excavations for the spoil conveyor tunnel and borehole data from subsurface instrumentation installation provided the first construction phase data followed by the commencement of tunnel boring machine (TBM) excavation. Routine cutterhead inspections coupled with ongoing reviews of the predicted geology resulted in clear response triggers to selection of segment types while detailed inspections in passage locations provide the initial classifications for segment removals.CITATION:Bennett, C and Norbert, M, 2014. Tunnelling within the Bunya Phyllite of Legacy Way, Brisbane, Queensland, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 131–140 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By X Li, J Wang, D Liu, Y Liu, K Hu

"Since the adoption of open-door policy 30 years ago, rapid economic growth has resulted in serious resource depletion and environmental destruction, especially in mining areas. As an urgent response to this situation, the central government and the Ministry of Land and Resources (MLR) have adjusted policies with concrete and realistic actions for halting this trend of non-sustainable mining activities in China. æGreen Mine CampaignÆ is one of the actions implemented. In 2010, MLR announced the æGreen Mine CampaignÆ, in which existing and new mines will be evaluated against the æGreen Mine Construction StandardsÆ and certified as æGreen MineÆ if complying with these standards. The standards cover five key aspects: the considerations of science-supported resource exploitation efficient resource utilisation standardised management environmental friendliness harmonious community relationship.Every year, MLR reviews ægreen minesÆ from all provinces. Thirty seven mines, including coal, metal, non-metal, gold, chemical industry and building materials mines, passed the review and were certified as green mines in 2010. In 2011, 187 out of 194 mines that participated in the review were certified as ægreen minesÆ. These mines are viewed as good examples of sustainable mining development in China.CITATION:Liu, Y, Hu, K, Li, X, Liu, Y, Liu, D and Wang, J, 2012. The green mine campaign and sustainable mining in China, in Proceedings Life-of-Mine 2012, pp 339-342 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jul 10, 2012

By A J. Burchell

The introduction reviews the tunnelling carried out in Singapore since the early 1980s. Between 1983 and 1990, Phases 1 and 2 of the mass rapid transit system were constructed. These included some 20 km of bored and cut and cover tunnels together with 18 underground stations. Some particular points of interest in this massive project are briefly commented upon. Reference is also made to other underground or underwater schemes undertaken during this period such as the proposed large caverns project and the submerged tunnel to Pulau Seraya. A description of the subsurface works, now under construction in Singapore, follows. This includes an all underground North-East railway line 20 km long with 16 stations. At a budget of US$ 3 billion, this is a major civil engineering undertaking. Another project is the extension of the railway to Changi Airport which involves 3.5 km of twin tube tunnelling together with a major underground station which is fully integrated into the airport terminals. An on-going program of further major railway extensions over the next 10 to 15 years is in place and an outline is given of some of the most important underground sectors. Other proposed projects such as the underground roads system and the deep level sewers are briefly described. Together they demonstrate the very significant volume of underground construction scheduled for the next century in Singapore.

Jan 1, 1999

By E Nettleton, A Melkumyan

A probabilistic system for autonomous tracking of excavated ore in mining would be highly valuable. Currently, mine sites can have a vast array of sensors; examples include excavator load cells, bucket volume estimators and haul truck strut pressures which can be used to gather information about the excavated ore at different locations. These sensors can be utilised efficiently to increase the accuracy of mine estimates by introducing a real-time ore tracking system. This requires the introduction of a probabilistic ore tracking framework to consistently fuse information from any sensor input. Current modelling practices are manually intensive, deterministic (no recognition of the quality of data) and generally not a complete end-to-end system. This paper will provide a novel method for tracking extensive ore properties (mass, volume) and intensive ore properties such as chemical composition (eg Fe per cent, SiO2 per cent, Al2O3 per cent). This method is proved to ensure that correct correlations between states are conserved as material is transferred, combined and/or separated at different locations with any configuration of sensor inputs. This ensures that consistency of estimates is maintained and other benefits such as real-time probabilistic reconciliation can be implemented. A method for combining material of different mass and chemical compositions is also developed to enable accurate and efficient operation of the system. Representative experiments on a small-scale and a larger field trial which mimic the mining processes of excavation, haul and unload to ROM Stockpile will be used to verify the approach.

Sep 26, 2011

By A T. Spathis, K E. Leslie, K R. Blay

Many open pit mining operations seek to control blasting-related movement of ore and waste to minimise loss and dilution. Tracking the movement of ore boundaries can result in the maximisation of ore recovery and minimisation of waste sent to the mill, thereby optimising the economic performance of the operation.A novel solution for tracking the ore–waste boundary location before and after a blast uses subsurface markers placed along the boundary with all measurements and scans conducted remotely from the blast block. Upon system activation, user-operated equipment on the surface determines the three-dimensional (3D) location of the subsurface markers.The patented system concept combines two electromagnetic mechanisms, magnetic positioning and radio frequency through-rock communications to enable remote battery-powered markers, buried within the rock to be accurately located in 3D space.Field trials at a quarry have demonstrated the system can comfortably handle over 100 subsurface markers with a complete scan, including set-up, taking less than an hour. Location accuracy for each marker in 3D space is better than 0.5 m at a range up to 50 m from the magnetic source, and the system has an overall operational range in excess of 75 m.CITATION:Blay, K R, Spathis, A T and Leslie, K E, 2015. A remote, rapid and accurate three-dimensional ore waste boundary tracking system, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 297–306 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By D Luppnow, H Rourke

Recent disasters such as the failure of the Mount Polley tailings embankment remind us of the risks that tailings facilities pose. It is widely recognised that dam-break assessments are a vital tool in identifying the consequences of the failure of a facility, which in turn can be used to develop emergency action plans. A typical assessment includes an estimation of breach parameters and outflow volume, followed by the preparation of an inundation map to illustrate potential flow extents and downstream impacts. This paper focuses on the estimation of outflow volumes, which is an area that the authors feel can be improved. Presently, many types of analyses assume that the volume of tailings released is only a function of the storage volume and dam height. After a review of several documented tailings failures, it has been found that the extent and depth of the supernatant pond needs to be considered as it is just as important, if not more so, as the storage volume and dam height. Tailings facilities with excess water storage have a higher risk of failure as they are more susceptible to overtopping, piping and liquefaction failures. In addition, they pose greater failure consequences as the saturated conditions will lead to more material being mobilised.This paper has reviewed available information on a number of tailings dam failures and proposes an alternative estimation of potential tailings release volumes as a function of supernatant water stored on the facility for use in dam-break analyses. In a broader sense, the paper seeks to shift the current risk paradigm from tailings dam heights to volumes of water stored and provides a basis for continuing research and discussion.CITATION:Rourke, H and Luppnow, D, 2015. The risks of excess water on tailings facilities and its application to dam-break studies, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 225–230 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By B King

A large number of mineral deposits contain regions in which it is economically beneficial to extract ore both via open pit and underground mining techniques. Current industry practice lacks an effective means to establish the extent of the open pit and underground mining areas for an individual deposit. We present a mixed integer programming model for scheduling both the open pit and underground mine that can be used to create a holistic extraction sequence for a specific deposit. The model considers both spatial and temporal elements of the open pit and underground mines in order to maximise the net present value of the entire deposit, while adhering to its production, processing and block sequencing constraints. By doing so, we can schedule the open pit and underground in concert.CITATION:King, B, 2014. Modelling open pit and underground production scheduling in concert, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014 , pp 369–374 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 24, 2014

By J Boshoff, D Reid

It has been recognised worldwide that the liquefaction risk of unconstrained tailings stacks or cyclone underflow embankments requires careful consideration. The stability of a tailings deposit where the perimeter embankments are made up of hydraulic fill is often governed by post-liquefaction stability.Cyclones are frequently used around the world to classify tailings into a coarse underflow for building a tailings impoundment wall and a finer fraction that is disposed of into the basin. The shear strength of the tailings that form the outer embankment of a tailings storage facility (TSF) and the location of the phreatic surface are the two most significant factors influencing the structural integrity of the facility. The coarse underflow is placed in such a way as to contain the overflow, which is finer, has low strength and is often poorly consolidated.A cyclone field trial was undertaken at a gold mine in Western Australia to assess the feasibility of using the cyclone deposition method to optimise and increase the capacity of an existing tailings cell. The aim of the cyclone trial was to collect information to demonstrate to the client and the regulators that cyclone deposition was a feasible option for raising TSF embankments. The cyclone trial provided an opportunity to assess the cyclone under field conditions and the quantity and quality of the underflow fraction produced on-site. A variety of methods were used to assess the flow liquefaction susceptibility of the tailings underflow sample produced during the cyclone field trial.The field trial, laboratory testing and analysis will be discussed in this paper.CITATION:Boshoff, J and Reid, D, 2015. The resistance of cyclone underflow material to flow liquefaction, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 151–156 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By D Blair, L Fergusson, G Barros

"The purpose of this paper is to present the findings of a waste rock remediation program conducted at a gold mine in New South Wales (NSW) over a six-year period. The treatment of waste rock dumps included the longitudinal results of one-off applications using: ViroMine Technology, including the application of a chemical reagent called Terra B, which is a benign, clay-like substance derived from processed bauxite and other sources lime and biosolids (added for nutrient value) clay capping and topsoil compared treatment outcomes from these three approaches to a control.Parameters measured in the program included leachate pH, total actual acidity (TAA) and chromium reducible sulfur (CRS), Al, Cd, Cu, Fe, Mn, Ni, Pb, Zn, and tree height and vegetative cover density with data collected at regular intervals over a six-year monitoring period. Findings over the life of the study indicated, for example, that leachate pH in the control area was 4.5 in year 1 falling to 4.0 by year 6; pH in the lime and capping treated waste rock was initially raised to about 5.5 after treatment but fell to 5.0 within 24 months and remained a low 4.7 by year 6; pH in the Terra B waste rock was 6.8 in year 1 immediately after treatment, and actually increased to 7.3 by year 6 with no further treatment. This finding is of relevance because it effectively profiles the acidity curves of waste rock control, lime, and capping applications, and shows that they decline over time, despite an initial æpH shockÆ to the solids as measured by TAA and CRS in the case of lime. Similar treatment curves were observed for heavy metal leachates. Tree height and vegetative cover density indicated that with increasing acidity in the waste rock dump, the lime and capping options did not allow healthy revegetation, but in the Terra B treated areas tree growth and density were comparable to background, undisturbed forest levels.is needed with respect to tailings management, based on a novel integrated research framework.CITATION:Fergusson, L, Blair, D and Barros, G, 2012. Sustainable waste rock remediation and revegetation - A real-world longitudinal study comparing ViroMine technology to standard applications and doing nothing, in Proceedings Life-of-Mine 2012 , pp 249-258 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jul 10, 2012

By Q Zhuo, P C. Pistorius, M N. Al-Harbi

A likely increasingly important pathway for future low-carbon ironmaking and steelmaking is the combination of gas-based direct reduction with electric furnace steelmaking (DRI-EAF route), or with electric smelting (DRI-ESF route). In the DRI-EAF route, the gangue that is present in the iron ore is fluxed and removed as slag in the melting (steelmaking) step. This is in contrast with integrated steelmaking, in which the gangue is removed as part of blast furnace ironmaking. For DRI-EAF steelmaking, the amount and composition of slag depend on the iron ore composition, flux additions and iron yield. Slag volume and composition affect phosphorus removal, foaming behaviour and the process energy requirements. In this work, heat data from a year of DRI-EAF production was analysed to test whether the expected relationship between slag volume and electricity consumption for EAF steelmaking was observed. The data include slag analyses (one sample per shift), and heatlevel information on all inputs, final steel temperature and dissolved oxygen concentration, electricity consumption, tapped steel mass and tap-to-tap time. In analysing the data, the slag volume was estimated from the assayed slag CaO concentration and CaO inputs to the EAF. The expected effect of slag volume on steelmaking energy consumption was calculated with a mass and energy balance, considering the heat of mixing of the slag. The calculated energy requirement of slag formation is in line with previous estimates reported in the literature.

Aug 21, 2024

By S F. Rogers, K Doumis, J H. Graaf, B J. Barsanti

Advances in technology now allow geotechnical practitioners to better describe the properties and variability of a rock mass through advances in surface and underground mapping, borehole technology and geophysical imaging. Yet the way in which practitioners use this data is not being realised to its full potential and the quality and quantity of data that is collected is often superior to the conventional design approaches that are typically adopted. A discrete fracture network (DFN) approach provides the ideal basis for using this data to generate geologically-realistic rock mass models based on parameters derived from field data, which more effectively capture the variability and rock mass behaviour. However, until recently, the DFN approach has mainly been applied to cave mining and small-scale models associated with synthetic rock mass modelling or groundwater flow modelling for the nuclear waste and oil and gas industries.Ground support design for blocky rock masses in Australia is often dealt with in a rather traditional manner, adopting either an observational empirical approach through rock mass classification systems or conventional wedge stability analysis techniques. Using these methods requires several generalised assumptions about the rock mass fabric and excavation geometry. As such, the support system is often designed for a worst-case scenario based on a predetermined risk tolerance that the mine is willing to accept and a design block size that is generally determined by the proposed excavation dimension.A study by Doumis (2014) used conventional wedge stability analysis and the probabilistic key block analysis software JBlock (Esterhuizen, 1996) to estimate potential block sizes and support requirements. A DFN approach has also been adopted at Callie underground mine using FracMan™ software (Golder Associates, 2014). The methodology of the DFN wedge analysis will be compared with the key block analysis work undertaken by Doumis.CITATION:Graaf, J H, Barsanti, B J, Doumis, K and Rogers, S F, 2014. Towards the implementation of discrete fracture network modelling as a geotechnical design tool – case study of callie underground mine, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 399–408 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By K Gardner, R Fraval, V Singh

Using new technology to create optimised infill drill programs in underground or open pit settings, it is possible to quantify the value of a drill program. The computer designed programs are optimised to uplift the most amount of resource possible into the specified resource classification, while honouring geological, spatial, equipment and budgetary constraints. When designing ‘by hand’ balancing all these factors is a time-consuming effort with no real way to determine metrics on ‘how good’ a program will be. The optimisation considers many factors allowing geologists to apply critical thinking and domain knowledge to constrain the optimisation, letting the computer do the heavy lifting of determining hole placement. Once programs have been created, they can be integrated into a production schedule. This is a critical step in determining the correct sequencing and balancing of resource availability and seeing how a program will interoperate with other tasks in the mine. For example, if drill drives are a requirement for part of the program, will they be developed in a time frame that is useful for the goals of the program? Do we risk drilling infill holes too late to add value? Do we put production at risk by not classifying parts of the model ahead of time, thus adding to uncertainty? Using software to assist with optimising and scheduling of drilling is a useful technique to save the geologists from the mundanity of manually designing drill programs and puts metrics around the effectiveness of a program and has the potential to add quantifiable value to a program. Examples will be presented that demonstrate the effective use of drill hole optimisation, comparing manual designs with optimised designs, as well as the examples that show the effective use of scheduling.

Mar 22, 2022

By N Schofield

For the sampling of particulate materials in mineral exploration and mining, the fundamental sampling error (FSE) introduced by Gy is a measure of the constitutional heterogeneity of the sample lot and is expressed as the relative standard deviation of subsample grades of a particular mass. The FSE is presently regarded as an important indicator of quality for samples used in resource estimation. Constitutional heterogeneity describes an ideal state of heterogeneity with respect to all constituents of the lot such that the fundamental error among subsamples of a particular mass is minimised.In this paper, the term ‘sampling precision’ used in relation to mineral resource sampling usually refers to a statistic based on the assay results drawn from pairs of separate subsample splits of multiple sample lots. The pairs of splits are extracted after the lots have been prepared by crushing and pulverising to meet specified criteria of grain size and subsample mass. There is presently no generally accepted method of calculating the ‘sampling precision’ from such paired data but some form of the relative standard deviation that is consistent with definition of the FSE is preferred here. The work of Thompson and Howarth in the 1970s on geochemical analytical precision, which has been subjected to extensive examination and criticism by Stanley and Lawie (2007), and that of Francois-Bongarçon since the 1990s forms the background to the discussion in the paper.A significant aspect of the application of Gy’s sampling theory to sampling in gold deposits is the requirement that the fundamental error be maintained at less than ±20 per cent. The most important reason for this is to ensure that the effects of other sampling errors such as the grouping and segregation, and increment delimitation which can cause local and global biases in sampling are kept as small as possible. This paper is focused mainly on the quality of sampling in gold deposits and looks at an alternative to the use of a constant sampling precision applied to a collection of lots with varying average grade. A theoretical model for the FSE based on duplicate sampling is presented and the simulated results of the model are compared to practical outcomes of real duplicate pairs drawn from multiple sample lots. The goal of the work is to present a more informative analysis of duplicate sample data from multiple lots which may allow a more informed view of the potential for bias generating errors during sample preparation and processing.

Aug 22, 2011