Search Documents

By F C. D Michelin

Blast fumes are a significant health risk to underground workers, containing several dangerous gases such as carbon monoxide (CO), nitrogen oxides (NOx) and ammonia. To ensure safe working conditions, workers are not normally allowed to re-enter a mine until the gases are cleared. To predict if gases can be cleared efficiently, simulations can be performed to estimate the gas levels following a blast. For accurate modelling, a calibrated airflow simulation is required in addition to blast-specific parameters such as the yield rate (representing the amount of gas released per kg of explosive) and the dispersion factor (representing how quickly the gases can enter the air stream from the explosive site). Those parameters are not easily determined, as they will vary from blast to blast. Many post-blast gas recordings on mine sites were studied and the correct parameters were determined to ensure an accurate gas simulation. The variability of the results was then analysed and correlation to known parameters is suggested. Finally, recommendations on how to determine the correct parameter are presented.

Oct 12, 2022

By D Reid

Many of the relevant engineering behaviours of tailings are controlled to a large degree by the density of the material. For example, loose tailings are prone to brittle strength loss, while dense tailings are dilative (i.e. gain strength) at large shear strains. The critical state framework has been successfully developed over the past few decades to assess whether in situ conditions are contractive or dilative, and estimate relevant engineering parameters on that basis. Tailings comprising primarily silt-sized particles, when subaqueously deposited, often form a particularly loose state compared to subaerially deposited material of similar index properties. Such subaqueous deposition occurs in the decant pond area, where the tailings typically pluviate in quiescent conditions within a pond of standing water. Silt tailings deposited in such a manner have been observed to be extremely loose in a number of TSF investigations. Of particular concern, the deposited material in such cases appear to be significantly looser than can be reproduced in the laboratory - even using moist tamping, the sample preparation method which can usually produce the loosest samples possible in laboratory conditions. While the loose density of subaqueously deposited silt tailings is clear, in a well-managed upstream-raised TSF the decant pond is usually small and far from the perimeter embankments, however there are a number of examples where the engineering performance of such materials becomes relevant – for example, when historical deposition practices were poor, resulting in subaqueous deposition near the perimeter embankment. This paper outlines the geotechnical characterisation of a number of such subaqueously-deposited zones, compares the in situ state to that achievable in the laboratory, and discusses options for assessing the expected engineering performance of such materials when comparable laboratory tests are unavailable.

Jul 1, 2021

By G S. Beros, K M. Edwards

Over the past 20 years drum scrubbers have become a widely adopted technology within iron ore beneficiation plants. Generally, the drum scrubbers in use are considered high-capacity machines capable of accepting larger-sized feed material. Together with a water addition to a desired pulp density and a mild energy input, these large rotating machines effect an attritioning action that removes water soluble clays and other deleterious materials. Within the Western Australian iron ore industry, drum scrubbers have been successfully applied to Channel Iron, Marra Mamba, Bedded and Detrital orebodies. The introduction of drum scrubbers has enabled Western Australian producers to satisfy the substantial increase in demand for iron ore from Chinese steelmakers by making the lower-grade sections of the above orebodies economic. However, despite being a relatively simple unit process, the requirements for successful design and operation of these machines are not fully understood. This paper draws on the collective experience of both authors to provide some points to consider for incorporating drum scrubbers into iron ore beneficiation plant flow sheets.

Sep 18, 2023

Sampling protocols and metallurgical flow sheets should be designed to suit the style of mineralisation in question. In support, the a priori need for evaluation programs is the characterisation of the mineralisation type(s) and domain definition. The proportion and size of gold particles has a direct impact on the effectiveness of sampling protocols and metallurgical processes employed. Within the coarse- to-fi ne gold spectrum, the samplability of a deposit ranges from relatively simple for fine-grained disseminated particles, through to difficult for coarse gold mineralisation. Conversely, metallurgical processing may be relatively simple for coarse gold ore and more difficult for very fi ne gold ores. Most deposits contain a proportion of both particle size types. The nature of mineralisation, mineralogy and associated gold particle sizing can only be determined by preliminary sampling to facilitate testing. Mineralogical studies, focussing on ore mineralogy and gold particle deportment, size and distribution are required as part of wider paragenetic and geometallurgical investigations. This paper discusses key issues and presents a methodology for the determination of gold particle size in coarse gravity-gold ores to support sampling optimisation and which also contributes to metallurgical characterisation.

Aug 1, 2010

By M T. Grigoleit, M S. Schneider

The iron ore industry in Australia has, in recent years, experienced an unprecedented growth phase. But now that major expansions are moving into the operation phase, new challenges have emerged. Whereas initial planning may involve a few modelling studies, ongoing performance monitoring and improvement requires a different, more intense approach. This is especially important in the face of changing factors such as commodity prices, exchange rates and labour markets. Response time is key. As a mining operation proceeds from initial planning to daily operations, the time window for analysis shortens, going from months to weeks to days as the business matures.Simulation models and analysis tools are typically built and run by specialists in the planning phase, but then what? The investment has been made, but realised only once. What if further analysis could be carried out in-house, re-using existing models using up-to-the-minute data? Can we create virtual mines that run in parallel to live operations that allow computers to identify areas of a value creation or operational improvement? These questions can be answered by the innovative application of big data, simulation and predictive analytics. The future will be having this all integrated into one platform that offers, for the first time, an opportunity for non-experts to apply existing modelling and analysis assets – combined with live data – to deliver support for continuous improvement, and the ability to respond quickly to external changes in the best possible way, before they become big problems. These techniques will represent a step change in the ability for operations to maximise efficiency and will underpin the intelligent operations of the future. These issues are addressed in this paper.CITATION:Schneider, M S and Grigoleit, M T, 2015. Maximising productivity through big data, simulation and predictive analytics, in Proceedings Iron Ore 2015, pp 475–480 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By J L. Macdonald, G S. King

"The development of a predictive geometallurgical model is a multidisciplinary and iterative task that involves both discovery and integration aspects. In this paper, the authors discuss the concepts of geometallurgical modelling in terms of the underlying relationships that are used to connect geology, metallurgy and economic value, and how the early-stage preparation of a spatial geometallurgical model enhances project value and provides a sound basis for future studies and test work programs.Hot Chili’s (copper-gold-molybdenum) Productora Project, which is located in northern Chile, is a porphyry-copper style deposit that can be exploited using open pit mining and preparation of a saleable concentrate from fresh ore, as well as heap leaching, solvent extraction and electrowinning (SX-EW) extraction of copper from oxide ores. To enhance project value in the Productora prefeasibility study (PFS), Hot Chili developed a geometallurgical model that was used to predict the process responses of both sulfide and oxide ores. The Productora model incorporates test results from mineralogical, metallurgical and comminution testing, as well as other studies completed on a suite of samples collected from the many geological domains of the deposit.Using Bond Work Index and Abrasion Index proxies in the geometallurgical model, Hot Chili estimated the variability of sulfide ore throughput and comminution costs. Heap leach acid consumption in oxide ore was estimated from drill hole calcium concentrations. The model was then used in mine scheduling to identify high and low throughput or high and low acid ore zones so that the processing of these zones could be advanced or deferred to improve net present value (NPV). Additionally, the cost benefits of preparing an early-stage geometallurgy model were quantified through a comparison to a conventional model that was based on test work averages.CITATION:King, G S and Macdonald, J L, 2016. The Business Case for Early-stage Implementation of Geometallurgy– an Example from the Productora Cu-Mo-Au Deposit, Chile, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 125–134 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

By D A. F Oliveira, C J. Parker

The role of the virgin in situ stress field in tunnelling projects is well known in the Sydney area. The effect of in situ stresses is mostly considered through the use of published relationships that describe the in situ stress conditions as a function of depth. Considering the significant scatter in the data, it is evident that by adopting such relationships, the designers are assuming an average distribution of stresses with depth that is generally a reasonable engineering approach; however, when building a geomechanical model, the tunnelling or geotechnical engineer needs to account for the interrelationship between ground conditions (rock mass quality – fracturing, strength and stiffness) and in situ stress, which may explain part of the stress data scatter. This paper presents an alternative approach for interpreting in situ stress conditions, valid for both Sydney sandstones and shales that focus on such interrelationship between in situ stress and ground conditions.CITATION:Oliveira, D A F and Parker, C J, 2014. An alternative approach for assessing in situ stresses in Sydney, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 189–194 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By G Guy, J Summerville

Over the past five years in coalmine slope evaluation the application of 3D modelling has increased significantly as software has become more user friendly but also areas requiring evaluation have become increasingly complex. Often simplistic 2D Limit Equilibrium modelling and analysis has been poorly used to solve slope stability issues by back analysis and subsequent forward predictive analysis. A plane strain condition with slope movement perpendicular to the slope strike is assumed where in reality the problem is more complex. This often leads to a misinterpretation of the failure mechanism because the failure mechanism being modelled in 2D does not generally represent the actual failure mechanism observed in the pit, with 2D modelling often oversimplifying a slope. This paper presents a case study where the initial slope assessment and remedial design evaluation was undertaken as a 2D Limit Equilibrium model which led to an overly conservative and costly remedial solution being implemented. Subsequent modelling of the slope using both 3D Limit Equilibrium and Finite Element methods were able to provide a better understanding of the structural complexities associated and correlate well with slope monitoring data to create a more realistic outcome.

Nov 29, 2022

The key issue which determines the use of imaging for explosives and mining research is the question - `What information will I gain by using imaging technology?' This paper will address that question from the point of view of a researcher and cameraman working in industrial imaging and photography. The paper will establish a common set of reference standards for high speed imaging and photography which researchers can apply when deciding which type of imaging technology is appropriate. It will present an overview of current image analysis technologies and practices in use across a range of appropriate scientific fields and draw lines of commonality of approach between these fields and the field of explosives and mining analysis and research. Further to this, the paper will examine the different technologies from an image quality reference point, ease of operation, cost, and reliability parameters. Finally this paper will present an argument for the hybridisation of established and new technologies which could provide a more beneficial approach to the use of imaging as a tool of research and analysis in the explosives and mining industries. This will include a novel approach to high speed filming and analysis in the field which should deliver high quality images in a time frame which is more appropriate to urgent action and solutions.

Jan 1, 1995

By M Tsai

Tube bundle gas monitoring systems have been used in the mining industry for over 50 years. The initial design was based on four individual gas analysers along with a series of solenoid valves, gas sample conditioning and flow control mechanisms to ensure the correct gas flow stream volume to the analyser. Simtars staff have identified flow control issues when providing operational support to coalmines on numerous occasions. The accuracy of the oxygen analysis is dependent on control of the gas flow to the analyser. Oxygen is one of the parameters used in calculating Graham’s ratio which is used for the detection of spontaneous combustion activity in coalmines. This paper will provide data which identifies the flow control issues by comparing mine site records for the two surface sample lines in the analyser room and the gas cage. Mine sites will be deidentified within the paper. The paper will discuss some of the changes that have been made in modern tube bundle systems and compare the change to the initial design specification developed by the UK National Coal Board, investigate possible operational impacts and provide a technical fix to solve the current flow issues being experienced at some mines.

Oct 12, 2022

By T Walsh, S R. Mudnuru

The development of lithium-ion batteries, coupled with the global trend towards electrification of transportation, has led to a dramatic increase in the demand for lithium. The production of lithium from hard rock ores is increasing, and flotation has proved to be an effective means for the beneficiation of many pegmatitic lithium ores. Clariant Mining Solutions has developed a range of novel collectors for the flotation of spodumene and other lithium ores, and this paper presents examples of some of the most recent developments. Fatty acids are the typical collectors for lithium flotation, however the grade and recovery achieved with these collectors is often below the desired level. There are also some significant drawbacks associated with the use of fatty acid collectors, such as the formation of calcium soaps which give rise to filtration problems and the need for acid washing. Several FLOTINOR products have been developed as alternatives to fatty acids. These products offer equivalent or better metallurgical performance at significantly lower dosages than fatty acids. This offers benefits to the flotation circuit as well as potentially reducing the issues associated with downstream processing of the concentrate.

Aug 24, 2022

By R Cooksey

The Globe-Progress Mine is an open pit gold mine that is part of the larger Reefton Goldfields deposit located on the West Coast of New Zealand. The regional geology comprises a series of north to south oriented fold structures that have undergone post-deformation mineralisation. The structural geology within the mine itself is more complex, with major shears hosting numerous high-grade mineralised quartz shoots and splays that have been historically mined.The selective mining of ore within the pit is challenging due to the orientations of the hanging wall and footwall areas of the main Globe shear zone, the lithologies of these areas which range from highly brecciated and sheared material to competent mineralised host rock, and in the hazards presented by the numerous old historic underground workings. The coordination of drilling, modelling and excavation of the ore requires careful planning to maximise recovery whilst operating with the pit design boundaries.Grade control packages are custom designed to reflect the orientation of the footwall and hanging wall mineralisation. The shear material in the footwall zone dips between 60° and 70° and requires angled drilling whereas the footwall mineralisation is contained in shallow dipping quartz veins sub parallel to bedding and can be vertically drilled to best intercept the mineralisation. Ore excavation is directed so that the contact between the footwall and hanging wall is mined in the correct direction so that any non-visual ore contacts can be safely mined and that the ore-waste dilution is reduced.The ongoing grade control and selective mining of the Globe Progress deposit continues to deliver high grade ore for processing by ensuring that waste and dilution of ore is reduced and that recovery is maximised.

Aug 22, 2011

By K Haga, G Danha, A Shibayama, L L. Godirilwe

The hydrometallurgical separation and enrichment processes provide an effective way to selectively recover metals from relatively dilute multicomponent sulfuric acid leach solutions. The multicomponent leach solution utilised in this study contained 0.3 g/L Cu, 0.34 g/L Ni, 0.13 g/L Co, and 2.96 g/L Fe, which was obtained after high-pressure oxidative acid leaching (HPOAL) of the copper-nickel smelter slag. The solvent extraction (SX), precipitation, and xanthate complexation processes were employed to recover and upgrade Cu, Ni, and Co from the leach solution. Batch SX tests were carried out using a countercurrent two-stage mixer settler extraction column, and LIX 984N (10 per cent v/v) as a copper extractant. Fundamental parameters influencing the extraction process such as pH, mixing speed, H2SO4 concentration, and organic/aqueous (O/A) phase ratio were investigated. For copper enrichment in solution, a combination of two extraction stages and two stripping stages were employed. Copper was successively separated from Fe, Ni, and Co under optimised extraction conditions (pH 2, 400 rev/min, O/A 0.25, and 20 min contacting) and stripping conditions (175 g/L H2SO4, 400 rev/min, O/A 4, and 20 min contacting). About 97 per cent of copper was extracted with low co-extraction of Fe, Ni, and Co of about 5.90 per cent, 1.47 per cent, and 2.53 per cent, correspondingly. A final Cu-rich solution containing 23 g/L Cu was obtained with a very low Fe concentration of 0.05 g/L. Additionally, for iron removal from the Ni/Co raffinate solution, more than 99 per cent of iron was precipitated at pH 4 by the addition of a calcium carbonate (CaCO3) suspension, with low co-precipitation of nickel and cobalt of around 3.68 per cent and 2.27 per cent, respectively. Furthermore, about 83.6 per cent of nickel and 99.4 per cent cobalt were co-precipitated from the solution by potassium amyl xanthate (PAX) solution at pH 6. The Ni and Co xanthate complexes were thermally decomposed and recovered as cobalt oxide (CoO) and nickel sulfide (NiS) solids.

Aug 24, 2022

By G D. Matthews, M E. Haylett, S Khosrowshahi, A Weeks

In narrow orebodies the use of ordinary kriging (OK) may pose certain limitations when used for grade control modelling. The smoothing effect of kriging, by its very nature, cannot retain or accurately characterise the dispersion (variability) that is inherent in gold deposits. This dispersion is a critical component of determining the desired level of ore loss and dilution.Fixed block model positions used in OK, and all estimation approaches, within a grade control process may never align with the ‘true’ ore boundary. This may lead to excessive ore loss and dilution, especially within narrow lodes.Using a risk-based approach to ore block design based on the geostatistical method of conditional simulation (CS) can highlight the differences achieved when an alternative method to OK is used for grade control modelling. By using a mesh of nodes and the application of a ‘transfer function’ to the simulation models, the position for ore contacts can be better assessed than when using fixed blocks in OK. Therefore, the value of various ore block boundaries can be better analysed by objective assessment of ore loss and dilution for a given minimum mining selectivity (selective mining unit or SMU), even in narrow lodes.A case study of a narrow vein gold deposit, comparing the results from an OK model and a CS model shows that whilst both models show similar trends – waste, low-grade, and high-grade regions are the same in both cases – the simulation model can provide greater insight for optimal definition of the mineralisation boundary.CITATION:Haylett, M E, Weeks, A, Matthews, G D and Khosrowshahi, S, 2014. Ore block design in narrow vein gold deposits – estimate or simulate?, in Proceedings Ninth International Mining Geology Conference 2014 , pp 421–424 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 18, 2014

By R Young

Independent Project Analysis (IPA) is in the business of benchmarking the performance of capital projects on behalf of owner companies in the processing and extractive industries. IPA assesses between 500 and 800 projects each year. The projects are conducted globally and range in size from about $1 million to over $30 billion. Using the data, we are able to benchmark the performance of Australian projects against the rest of the world. This presentation focuses on the performance of large (greater than $100 million) projects that involve chemical or thermal processing.We regularly hear calls for more processing to be conducted in Australia but on the other hand industry leaders are concerned about the poor success rate of solids processing projects in Australia. Data gathered by IPA indicates that there is good reason for the concern. Out of a sample of 31 large processing projects conducted in Australia, 23, or 74 percent, were classed as failures. This performance is significantly worse than for similar projects in other parts of the world. The presentation analyses why the performance is worse and demonstrates that many of the reasons behind the failures were manageable by the project team. Furthermore, members of the project teams on at least half the failed projects knew that the projects were on a path to failure before the project was authorised but could not be heard.The presentation discusses how large projects that involve process design and, in many cases, new technology, need to be set up for success. *This is an abstract only. No paper was prepared for this abstract.*

Aug 8, 2011

Mining education in Ballarat has a long and proud history dating back to the 1870s. Today the School of Engineering continues this tradition at the University of Ballarat. The recent review of Tertiary Minerals Education by the Minerals Council of Australia has questioned the current situation regarding Minerals tertiary education in Australia and recommendations have been made regarding the future of minerals tertiary education. This paper initially examines the original recommendations made by the Minerals Council of Australia and assesses subsequent changes made to these recommendations. Secondly the paper outlines the future shape of mining education in the light of these recommendations given that they are implemented. Finally the future delivery of mining education is discussed, particularly with respect to the impact of modern technologies.

Jan 1, 2004

Exploration and mining title administration in the Northern Territory has changed dramatically over the last 20 years. These changes have occurred due to legislative amendments, technological developments, and the changing face of the mining industry. The first legislation to control mining in the Northern Territory was the Northern Territory Gold Mining Act (1873) of South Australia. In 1911, control of the Northern Territory was passed from South Australia to the Commonwealth. As a result of the mining boom which followed the discovery of gold in Tennant Creek in 1932, the Commonwealth passed the Mining Ordinance of 1939. This legislation was amended 39 times and stayed in force until July 1982, when the self-governing Northern Territory passed the Mining Act 1980. This Act is still in force and is continuously under review. The first computerised mining titles system, REGIS, was created in 1984/85 and was, to all intents and purposes, just a computerised index. Various modifications ensued, and in 1989 the Titles Database was unveiled. The database has developed to be one of the most sophisticated yet user-friendly mining titles databases in Australia. In excess of 50 companies have access to the database from their own offices. Work continues on its development and fine-tuning. The paper outlines the development of the database since inception.

Jan 1, 1994

By A K. B Chigwada

Mining organisations grapple with the same problems year after year, wasting incredible amounts of time and money. According to estimates from the International Labour Organization (ILO), over one million work-related deaths occur annually, and hundreds of millions of workers suffer from workplace accidents and occupational exposure to hazardous substances worldwide. Many accident reports cite human failure as a primary cause (Busse and Johnson, 1998). The workers at the Bhopal chemical plant pumped methyl isocyanate into a leaking tank (Morehouse and Subramaniam, 1986). On 3 December 1984, more than 40 tons of methyl isocyanate gas leaked from a pesticide plant in Bhopal, India, immediately killing at least 3800 people and causing significant morbidity and premature death for many thousands more. The company involved in what became the worst industrial accident in history immediately tried to dissociate itself from legal responsibility (Broughton, 2005). Australia is not spared from safety problems either (Lucas, 2022). The ILO Convention 176 (1995) as a response provides that national law should inter alia provide for the supervision of safety and health in mines; the inspection of mines by designated inspectors of the competent authority; the procedures for reporting and investigating of fatal and serious accidents; the compilation and publication of statistics on accidents, occupational diseases and dangerous occurrences; the competent authority to suspend or restrict mining activities on safety and health grounds until conditions giving rise to the suspension are addressed; and worker consultation on matters related to safety and health in mines. This has assisted in getting enough data to define the magnitude of the problem to the mining sector.

Apr 16, 2024

By A Scott, I Onederra

A great deal of technical and research effort has been applied to the development of models to predict fragmentation from rock blasting. A number of quite useful empirical or engineering models are currently available to blasting engineers and consultants, while more sophisticated approaches using mechanistic and numerical descriptions of rock breakage continue to be developed and applied by researchers and explosives companies.The fragmentation resulting from any blast will be heavily dependent on the properties of the rock mass being blasted; however, most empirical models rely on ‘rock factors’ generated from simple rock mass properties to describe the influence of the rock on the blasting outcome. In contrast, mechanistic models need explicit rock mass properties that require sophisticated laboratory measurements and detailed structural data if realistic outcomes are to be generated. The fragmentation modeller is caught between excessively simple rock mass descriptions for the empirical models and excessively complex data requirements for the mechanistic models.This paper briefly reviews the basis of a range of fragmentation models and the rock mass properties on which they rely. Shortcomings in the way that the mining industry tends to characterise the blasting properties of rock are discussed and some practical approaches are described to quantify these properties in both operating and greenfield mining environments. Case studies are presented where specific additional breakage properties and modelling features have been needed to generate a useful description of the fragmentation achieved.CITATION:Scott, A and Onederra, I, 2015. Characterising rock mass properties for fragmentation modelling, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 149–160 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By R Jacobs

"The Jaguar project is relatively unique in that it was evaluated, financed, built and operated to completion within the last ten years, providing the opportunity to holistically review and reconcile expectations against the actual outcomes. It is a case study that allows wider conclusions to be drawn with respect to the risks and opportunities involved with project evaluation and execution.Jaguar is located in the Leonora Mining District of Western Australia and was commissioned in mid-2007 as an underground accessed, single high-grade volcanic-hosted massive sulfide (VHMS) deposit with an on-site concentrator, producing copper and zinc concentrates exported via the Port of Geraldton to South-East Asian markets.The feasibility study (FS) had several iterations (JML, 2005a); the last dated July 2005 was specifically targeted to secure project funding, and summarised the reserves-only portion of the resource and its planned exploitation. The commissioning of the mine was the transition for the owner Jabiru Metals NL from junior explorer to producer and the project was the dominant asset of the company.Jaguar operated through several significant deviations from the linear project plan set out in the FS, including the Global Financial Crisis (GFC), a corporate takeover and disruption to the mine plan from the onset of material geotechnical issues. Whilst the GFC or mining disruption were not specifically predicted in the FS or peer reviews, the generic effects of the events were assessed in the project risk assessment and they influenced subsequent management decisions. In parallel to the internal project-specific risks, the short planned life of Jaguar was a risk to the continuation of the corporate entity which was being addressed by significant investment into brownfields exploration to extend or replicate the project, and ultimately added value such that attracted a corporate takeover.Holistically, the project delivered the returns predicted in the FS, but in a much different guise than was expected. This paper will describe the reality of operations compared with the study predictions and expectations through the perspective of the project and corporate risk assessment.CITATION:Jacobs, R, 2016. Jaguar base metals project case study – has reality reflected the study?, in Proceedings Project Evaluation 2016, pp 86–97 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 8, 2016