Search Documents

By Iley J. D, Siviour N. g, Moffatt R. J

The process of desilverising by fractional crystallisation with reflux was investigated through laboratory batch tests and continuous laboratory bench scale tests at CSIRO Clayton, to a 300 kg/hr pilot plant at Port Pine. The pilot plant built at BHAS comprised a vertical cylindrical refining column with internal diameter 250 mm and height 3.2 m, attached at the top to an off-set cylindrical stirred crystalliser tank. Crystals were made in the crystalliser by intermittent immersion of steel cold fingers, which were water cooled between immersions. Gas heat was used for melting the crystals at the base of the column and for side compensation heating. A computerised in strumentation system was employed for data logging and for controlling some critical plant operations. A mechanical device was first employed to promote counter-current plug flow of crystals down the column against the rising stream of reflux liquid, but this was found to be unsatisfactory owing to excess noise, frequent mechanical failure, and excessive accumulation of dross. Plug flow was finally promoted by pulsing the column. Low silver levels, less than 1 gitonne, were achieved with both methods of crystal transport under total reflux conditions. The pulsed column gave results for silver and bismuth which agreed with the theoretical predictions of a computer model, but there was some selective drossing of antimony. In the mechanically agitated column, excessive drossing promoted selective removal of most of the antimony and some of the bismuth, and the results after extended operation were well removed from the theoretical predictions. Plant failures and operating problems prevented the achievement of satisfactory product quality with the necessary reliability under production conditions. Other priorities necessitated the termination of the project before the process could be optimised.

Jan 1, 1989

By S H. Algie, D P. Taplin, S G. Doig

"Suboptimal performance of clusters of hydrocyclones (cyclones), relative to the performance of the individual cyclones that comprise the cluster, is a common phenomenon. The primary cause is well known: uneven distribution of the slurry feed into the individual cyclones. The direct result of uneven distribution is that each cyclone in a cluster performs somewhat differently. Hence, some, if not all, of them do not work at their intended operating points, and the classification is not as sharp as intended. The impact on grade, recovery and milling efficiency will vary depending on the duty of the processing circuit, but the most immediately apparent consequence of uneven distribution is a difference in wear rates in the individual cyclones; this exacerbates the problems of unequal performance of the individual cyclones. In severe cases, and as differential wear proceeds, flows from the individual cyclones may become visibly different. Uneven distribution, once the phenomenon was identified, was seen to be a significant issue in the high-solids hydrocyclone cluster in the ball mill recycle section of Evolution Mining’s Edna May Operation (EMO, Westonia, Western Australia) gold processing plant. In 2012, a FloCEP® hydrocyclone feed distributor system was installed to alleviate the problem. Over the next four years of operation, this innovation has proven its value in the metallurgical and maintenance areas. Individual cyclones now wear at the same rate, greatly reducing the need for operator intervention, as well as increasing overall plant availability through minimising unplanned maintenance. The costs of the installation can be justified by savings in maintenance alone, though the greatest value, as is described in this paper, is in allowing the plant to produce consistently closer to its operational design limits. The FloCEP® system is a low maintenance, readily installed retrofit, based on two patented devices that are combined with complementary proprietary design methodology allowing customisation for specific flow rates and slurry particle properties. Together, these devices produce and distribute a pseudo-homogenous slurry flow without moving parts.Citation:Taplin, D P, Doig, S G and Algie, S H, 2016. Experience with FloCEP® Slurry Flow Conditioning at Evolution Mining's Edna May Operation, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 251–260 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By N Cann

In the 10 years from 1998 to 2008 the annual number of fatalities in the Australian mining industry has plateaued (MCA, 2007-08 and abc.net.au website). Despite significant efforts to eliminate fatalities, this is not a comfortable statistic in this very public performance indicator.GHD has been working with the mining and minerals processing industry to identify the key risks that lead to fatalities utilising a semi quantitative risk assessment technique (SQRA®), initially developed to assist Major Hazards Facilities prepare Safety Cases (OH&S, 2007-08) in response to the Longford Incident in 1998 (Dawson and Brooks, 1999).Workshop cross functional teams are assembled from the sites and led by the GHD facilitators to identify the incident types that can have fatal consequences, the causes of those incidents and the controls that are utilised (or could be utilised) to reduce the risk. The risks for each incident type are quantified to produce a risk profile for the facility and the critical controls – the controls that have the greatest impact at reducing the risk of fatality – are selected. These controls are assessed for their adequacy and improvement actions are identified. Prioritisation of the actions is achieved by re-estimating the incident risk profiles.A review has been undertaken using a small sample from the more than 100 individual studies that GHD has completed at mining and minerals processing sites. The five most significant risks reported by sites are:1. Fall from Heights,2. Vehicle/ Vehicle and Vehicle/Pedestrian interactions,3. Entanglement,4. Molten Metals and Materials, and5. Electricity.The most significant reductions in risk identified were found to be by implementing engineering controls. Examples include:1. Chutes to contain splashes and spills of molten materials,2. Redesigning instrument and equipment layouts to take personnel away form high risk areas,3. Designing remotely operated equipment to remove personnel away from high risk areas,4. Proper fire fighting equipment provisions such as deluges around flammable materials, and5. Adequate risk assessment to ensure equipment is designed to handle the real situations and not a design case to meet an arbitrary specification.All of these cases and many of the actions identified in the studies could have been handled through better design and construction early in the life of a project rather than retrospectively fitted after operations have begun.

Aug 8, 2011

The Pacific Rim countries ofAustralia, New Zealand, Papua New Guinea, Indonesia, Fiji, Philippines and Solomon Islands will be reviewed from an equity investors perspective.   The following areas will be covered: Country risks Exploration spending and activity Project development Taxation Relative cost of doing business Environmental considerations Political/bureaucratic situations Capital raising Equity markets as a source of funds Developing market funds The aim of the paper will be to outline the most attractive areas for investment by equity and private funds plus documenting the changes needed in the less favourable countries if they are to attract investors.

Jan 1, 1995

Stilfontein Gold Mine, located approximately 160 km west of Johannesburg, produced both gold and uranium from 1952 through to the early 1990s. On decommissioning the mine infrastructure, treatment plants, rock dumps and three tailings facilities were left to be rehabilitated at considerable cost to the mining company. The community that had grown up with the mine and had settled in the mine village were faced with deteriorating socio- economic conditions.   Mine Waste Solutions (MWS), a company with a socio-economic Vision expressly created by DRD (Pty) Ltd and Fraser Alexander (Ltd) for the purpose, took over the mine surface infrastructure with the objective of closing it down in an economically sustainable manner by recovering materials, converting mine infrastructure to useful purposes and re-mining of the tailings to recover residual gold to finance the project. A business case was prepared and presented successfully to investors and bankers and the project was commenced in 2003.   The paper covers the scope of the project and gives an account of the practical lessons that were learnt as the project developed over a period of five years. Key technical issues that are covered by the paper are the re-mining techniques that were deployed to clean up the old tailings dam footprints and the selection of the deposition site to minimise the incremental impact associated with the tailings and concurrent rehabilitation of the facility. In addition the paper will outline the positive benefits that were generated for the community and the improvement that was achieved in the physical environment.   The paper illustrates clearly how a mine can be closed in a manner that produces benefits for the community, the environment and the investor.

Jun 1, 2010

By P Walker, I Crnkovic, D Bennett

The Phu Kham deposit represents a copper-gold porphyry system, with mineralisation present in skarn, stockwork and disseminated styles. Significant folding and alteration events have created a complex heterogeneous mineralogy horizon. Weathering and water table contact have created a leached zone, overlying transition zones with supergene chalcocite- dominant secondary copper mineralisation and clay-rich gangue. Primary ore copper mineralisation is mainly chalcopyrite with minor bornite. The major challenges to the copper-gold flotation process are a wide size distribution of chalcopyrite mineralisation and poor primary grind liberation, a high pyrite content in skarn ore requiring aggressive pyrite depression conditions, clay-rich gangue and non-sulfide copper mineralisation in weathered zones, and a significant association of gold with pyrite.The Phu Kham concentrator has been developed as a conventional semi-autogenous grinding (SAG) and ball milling circuit followed by selective rougher flotation, regrinding and cleaner flotation to produce a copper concentrate containing payable gold and silver values. The concentrator flow sheet design offered a capital efficient compromise between high copper recovery bulk sulfide flotation with large cleaning capacity, and lower recovery copper selective rougher flotation to ensure concentrate specification of 24 per cent copper grade could be achieved. This paper will examine and discuss concentrator flow sheet development, including projects implemented since commissioning to improve copper recovery, and future projects designed to maintain and enhance copper in concentrate production with decreasing copper grade and increasing pyrite content of ore feed, and increasing hardness of primary ore.CITATION:Bennett, D, Crnkovic, I and Walker, P, 2012. Recent process developments at the Phu Kham Copper-Gold Concentrator, Laos, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 257-272 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By E Nunes, R Mendes, D Jacobson, G Cota, T Machado, E Santos, J Almeida, E Pereira9, B Raso

Grinding circuits are known to be the highest consumer of energy used in the ore comminution process, with high operational costs and sensitivity to ore conditions. The mining industry is being encouraged to look for more energy efficient processes while increasing the mass and metallurgical recovery; a specific example is projects with lower iron ore grades, which demands a higher level of liberation and resulting higher energy consumption. This has led to increased usage of high-pressure grinding roll (HPGR) technology as an alternative design within the comminution circuit. A growing use of the HRC™ HPGR technology has been used to generate concentrate through a more sustainable process. In the Brazilian state of Minas Gerais, the readaptation of iron ore beneficiation circuits has been initiated, replacing the traditional crushing-to-grinding flow sheet with circuits using crushing-to-HPGR flow sheets, with the main driver being reduced energy consumption. Utilising results from sampling campaigns and analysis of experimental data collected in an industrial plant, the work herein presents a case study from the JMN Mineração operating plant, where the HRC™ HPGR was used as an alternative to traditional grinding using horizontal mills. The results show that the HRC™ HPGR performance in this iron ore processing plant showed benefits in terms of reduced energy consumption as compared to the projected performance with a traditional grinding circuit.

Sep 18, 2023

By H Arvidson, A Walker, N Pollock

Following the recent tailings tragedy in Brumadinho, the Investor Mining and Tailings Safety Initiative was formed representing institutional investors in the mining industry. This Initiative, led by The Church of England (CoE), requested data from 726 mining companies on each of their Tailings Storage Facilities (TSFs). What this exercise confirmed was that there was no public database of TSFs, and that there was a clear gap in tailings management systems within the disclosing companies. We present an approach using technology to support best practice TSF management, governance and disclosure which was originally submitted as part of University of Cambridge Post-graduate studies in Sustainability Leadership in January 2020. The aim of the paper is to discuss how technology could be used to deliver a Tailings Management Solution (TMS) that is aligned with the Global Industry Standard on Tailings Management (GISTM), and supports rigorous governance leading to disclosure. Subsequently the goals of the plan are aligned with that of the co-conveners of the GISTM (the International Council on Mining and Metals (ICMM), Principles for Responsible Investment (PRI) and United Nations Environment Program (UNEP)) which is to facilitate operators’ trajectory towards zero harm to people and the environment. Most of the focus to date around tailings management post Brumadinho has been on monitoring technologies, of which there are many. It is obviously important to acknowledge the critical role of monitoring technologies; however, our approach is agnostic to monitoring technologies and assumes that all of them are relevant. Our focus is on the data management, reporting and governance leading to disclosure of the information. Critical components of developing the TMS include adapting existing software products and solutions, recognising a system thinking approach is needed, strategic partnerships to deliver an accessible solution faster and more cost effectively, and, new ways of collaborating. The TMS should also accommodate relevant regional geotechnical codes and standards. The industry need for a TMS is well established and urgent, with significant pressure from regulators and civil society for the industry to address this significant issue.

Jul 1, 2021

By K M. P Singh, K M. K Sinha, G S. Jha, T Gouricharan, K K. Sharma

The majority of the powerplants in India are fed with non-coking coals, with the coals dispatched from their respective mines via wagons loaded by a rapid loading system or pay loader. The usual top size of coal is 200 mm and sampling is carried out manually from wagons. The manual method of wagon top sampling of large size raw coal is not only difficult, but also violates some of the fundamental principles of sampling. As per sampling requirements, samples are to be drawn from the full depth of the wagons, which is impossible to be done manually. Since the ash distribution in the different size fractions is not homogeneous, the results from the samples, which do not reflect the true size distribution of the lot, are likely to be biased. More importantly, sample collection by shovel from the top is a function of human discretion and not governed by the equiprobability rule. In another case, the sample has been collected by a cross belt-type auto mechanical sampler for 200 mm size coal at one of the super thermal power stations. Test analysis shows that coal collected using a cross belt-type mechanical sampler also has significant deviations from stopped belt coal samples of 200 mm size due to size segregation. Studies carried out on wagon top sampling through specially designed experiments reveal some interesting features. The presence of bias in wagon top sampling is apparent when compared with the ‘stopped belt’ sample. In this paper, a comparative study between manual wagon top sampling/auto mechanical sampling with respect to stopped belt sampling has been conducted for coal of size 200 mm. In addition, precision studies have been performed for wagon top sampling/mechanical sampling for Indian thermal powerplants.CITATION:Sinha, K M K, Sharma, K K, Jha, G S, Singh, K M P and Gouricharan, T, 2014. A comparative study of manual wagon top sampling and auto mechanical sampling of 200 mm size coal with respect to stopped belt sampling of thermal coal at Indian super thermal powerplants, in Proceedings Sampling 2014 , pp 43–48 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 29, 2014

By R W. Henley, L Knuefing, M Turner, Y Zhang, M Saadatfar, A Limaye, R Cruikshank, M A. Knackstedt, A Kingston, L Beeching, N Francois

A better understanding of ore fragmentation and the textural features of ore is a key to the energy efficient extraction of targeted minerals from low-grade ore deposits. In this study, X-ray microcomputed tomography (micro-CT) is employed to study mineral liberation during the tensile failure and onset of fragmentation of a copper ore. Our results show that X-ray micro-CT could inform new studies of ore micromechanics and fragmentation at the laboratory scale and may offer new avenues to address current challenges in the design of efficient comminution processes. We present the results of experiments based on a high-pressure apparatus enabling micromechanical studies to be carried out in situ (inside a micro-CT scanner). This platform produces high-quality 3D images of the evolution of a sample of porphyry copper ore during an in situ fragmentation test. A sequence of tomographic images enables mapping in 3D of both the deformation of mineral phases and the fragmentation process. The fragmentation occurs quasistatically through multiple stages starting with an initial tensile fracture splitting the ore diametrically, followed by tensile-activated nucleation and growth of multiple fractures producing a complex fracture network. Coupling breakage with microstructural information enables quantitative determination of the impact of ore texture heterogeneity on fracture patterns and mineral liberation. This microstructural information can be compared to key measurements of the ore mechanical behaviour such as the global deformation energy, strain deformation field and the stress relaxation response. The latter allows one to identify interesting precursor signals of the tensile failure. The copper liberation, fragment size distribution and breakage patterns are statistically characterised and related to comminution mechanisms which are clearly identified in the sequence of tomographic images. The two dominant mechanisms are rock-rock friction/compression induced by fracture closing and compression-driven fragmentation at rock-crusher contact points.

Aug 24, 2022

By M Kim, J Park, I-K Suh, E Kim, J Lee

One of the key technologies in developing hydrogen-enriched ironmaking operations is the control of the carburisation, melting, and dripping behaviour of the iron ore burden materials. When a hot compacted iron (HCI) is charged in the blast furnace or the FINEX Melter-Gasifier, iron oxide reduction, the reduced iron’s carburisation, and the melting of iron and slag occur successively. This study investigated the reduction, carburisation, melting and dripping behaviour of HCI under a COH2 gas mixture using the high-temperature X-ray radiographic technique. Under 100 per cent CO gas atmosphere, the dripping temperature was 1410°C. When 5 per cent H2 was introduced, the dripping temperature slightly decreased to 1400°C. Furthermore, the dripping temperature gradually increased as the H2 gas composition increased. As 30 per cent H2 was introduced, the dripping temperature reached 1414°C. The carbon concentration in the drained metal samples gradually increased with increasing H2 composition. It is considered that H2 decreased FeO content in the slag, yielding the increased melting temperature and viscosity of the slag. On the other hand, H2 accelerated the carburisation of the reduced iron by CO gas, enabling the homogenisation of the oxide materials to form a liquid phase. Therefore, it is considered that introducing H2 in the reactor is helpful to increase productivity and energy efficiency by accelerating the liquid phase’s formation.

Aug 21, 2024

By Butler I. K, Nicholson P. M

There are four main types of base metal and gold mineralisation recognised in the central Pine Creek Geosyncline. These are stratiform, polymetallic veins, stockwork/concordant gold-quartz veins and unconformity related uranium-gold-platinoid mineralisation. The stratigraphy of the central Palaeoproterozoic Pine Creek Geosyncline has been simplified into three groups comprising the Batchelor, Frances Creek and Finniss River Groups in ascending order. Stratiform mineralisation occurs within the Frances Creek Group. The earliest mineralisation is found adjacent to circular faults ringing basement highs. Higher in the stratigraphy, stratiform mineralisation is often associated with zones of high compression in the vicinity of basement highs. A synsedimentary-diagenetic origin for stratiform mineralisation is proposed. Polymetallic vein mineralisation occurs within the Frances Creek and Finniss River Groups. Its composition changes systematically through the stratigraphy similar to the stratiform mineralisation. The mineralisation is structurally controlled and usually occurs in the vicinity of basement highs. Stockwork-concordant gold-quartz vein mineralisation is hosted by the upper Frances Creek and Finniss River Groups. It occurs within compressional zones and along the Pine Creek Structure corridor around, above and particularly between basement highs. Mineable reserves occur in thick continuous semi concordant quartz-sulphide veins and/or stockworks. Unconformity related uranium-gold-platinoid mineralisation shows a close spatial relationship with the Palaeoproterozoic/Mesoproterozoic unconformity. The mineralisation is localised by structures formed during Mesoproterozoic deposition and is commonly adjacent to Archaean basement or its remobilised equivalents. The type of mineralisation (stratifom/polymetallic vein) is a reflection of local stress regimes, structure and physio-chemical conditions. An initial phase of stratiform mineralisation is postulated to have occurred with the first significant marine transgression in a tensional regime. A second phase occurred later during a compressive regime. "Ihermochemical sulphate reduction of mineralising fluids by hydrocarbons is invoked as the precipitation mechanism for the polymetallic vein type of mineralisation. Hydrocarbon generation is postulated to have occurred within the Frances Creek Group, in many places contemporaneously with the movement of mineralising fluids and basin compression. Polymetallic veins formed from the interaction of mineralising fluids and hydrocarbons which were trapped in suitable structures. An abundant, continuing supply of hydrocarbons was necessary to form significant deposits. Where these conditions were not net, the mineralising fluids largely continued their ascent to the near surface environment to form stratiform deposits. The stockwork/concordant gold-quartz vein mineralisation is a later event and occurred during the relaxation of compressional defonnation after deposition of the 1-inniss River Group.

Jan 1, 1994

By A Muhairini, M Eggers, J Smith, H Baxter

Detailed geochemical analysis of cored and non-cored drill hole data was used to characterise and model the Cenozoic detrital valleys of several deposits within the southern Pilbara region, Western Australia. The purpose of this modelling was to better characterise and understand the relationships between the various geotechnical units comprising mixtures of rock and soil for the purposes of slope stability and depressurisation studies.This paper presents data from several valleys where geological, geomorphological and climatic processes have resulted in the deposition of heterogeneous detrital rock and soil sequences. Seven primary detrital units are recognised as occurring within all the valleys studied, suggesting that the geological processes involved in the erosion and deposition of the units were widespread. Geochemical assessment of cored and non-cored data suggests correlatable geochemical signatures can be recognised for each of the units; however, local variability in the groundwater history of individual valleys is demonstrated by late-stage carbonate precipitation recognised both in the core and through the geochemical signatures, which has resulted in alteration of the parent rock/soil material. This paper discusses how the carbonate alteration may lead to improvements in rock/soil mass strength of a clay unit by comparing laboratory strength test samples of the same parent material with varying degrees of precipitate alteration to those with no discernible carbonate alteration. Following from this, correlations with geochemical assay results have been derived, whereby zones of more favourable strength conditions may be modelled through assessing areas of analogous geochemistry.The paper demonstrates how geochemical assessment can lead to improved geotechnical and hydrological modelling for a detrital valley system without the need for significant coring and laboratory testing. This in turn leads to improved confidence in the slope design and depressurisation recommendations for a slope.CITATION:Baxter, H, Eggers, M, Muhairini, A and Smith, J, 2015. The effect of carbonate alteration on detrital mass strength and implications for geotechnical slope design, in Proceedings Iron Ore 2015, pp 429–436 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By K J ROSENGREN

Underground rock mechanics was initiated as a formal discipline in Australia by early studies for underground structures for the Snowy Mountains Scheme in the 1950s. These techniques were quickly embraced by underground mining and there has been steady development to the present time. The paper reviews the status of current techniques for rock mechanics studies and discusses some important issues such as ground support, mine filling and caving. It concludes that a considerable degree of engineering judgement is still required for the practical application of rock mechanics to underground mine design.

Jan 1, 1992

By R H DAVIES

Peak Gold Mine is a new gold and base metal mining project being developed by Enterprise Metals (a 100 per cent subsidiary of CRA) at Cobar in the centre of New South Wales. The Cobar district has a long history of copper and gold mining operations stretching back to the 1870s. Extensive gold and base metal mineralisation was discovered at the Peak in 1981 below a series of gold mines which had been active around the turn of the century. Evaluation of the deposit through the 1980s led to CRA's decision to develop the project for production at a capacity of 450 000 tonnes per annum in late 1992. The project has been developed with a green fields approach despite the long history of mining in the local area. This approach has lead to several innovative ideas being trialed at the site which are expected to result in the operation being a low cost producer of gold and base metals.

Jan 1, 1992

By L O. Filippov, A Piçarra, I V. Filippova, N P. Lima, K Silva

The reverse cationic flotation using the starch as depressor of iron oxides is the most efficient upgrading process when is applied to the simple systems composed by hematite/magnetite and quartz. The fundamental studies performed with iron ore samples from different deposits over the world (Brazil, Russia, Mexico) confirmed the inefficiency of starch when the silica content in the concentrate is controlled by Fe/Mg-bearing minerals. The main approaches for solving these issues focused on using new collector formulations or new depressants. However, the alternative depressants tested inhibited flotation of quartz or were less efficient as iron oxide depressant. In this work, a comparison between new amidoamine collector with conventionally used etheramine and oleate collectors in the flotation of pure minerals and actual iron ore samples was performed. The electrophoretic mobility, contact angle and infrared spectroscopy measurements allowed to deduce the hindrance effect as main mechanism of selective adsorption of the amidoamine on the quartz surface compared to hematite and kaolinite. Molecular modelling studies revealed that this steric hindrance effect can be explained by the combination of the "shield" formed by the coordinating water molecules on the (001)-D2 hematite surface and the large volume of the amidoamine head group. The amidoamine tested as collector without use of a depressant showed excellent flotation selectivity allowing the total flotation of quartz from a mixture with hematite. High collector performance and selectivity were confirmed during reverse flotation of quartz using continuous flotation column (D = 500 mm; H = 4000 mm) and allowed to produce the iron concentrates with more than 60 per cent of iron from the rejected slimes samples of Vargem Grande 2 processing plant (Iron Quadrangle, MG, Brazil). The new collector allowed to develop flexible flotation flow sheets to process the iron ore with a complex gangue mineralogy and unlock the old altered tailings and slimes product as new resources

Aug 24, 2022

By M Schmid

German hard coal mining operations have decreased for more than 40 years. Current political decisions are leading to a discontinuation of subsidised black coal mining by the year 2018. This decision will, however, be reviewed once again in the year 2012. The enormous increases in productivity, which were achieved in previous years, have so far not led to an achievement of market requirements. Coal mining at depth of more than 1200 m in multiple seam environments is not yet competitive in global comparison. In 2008 the 24 faces left in eight mines produced about 20 million tonnes of usable steam coal. Management and the workforce will be reduced in parallel; from today until 2012 by more than half. The average age of personnel is increasing dramatically and nearly no new personnel are recruited. With this background in mind, increasing continuously coal mining productivity becomes more and more difficult. Above all, this goal was reached by mechanisation, then by increasing the mining machine power and then by enhanced machine control systems. The first attempts to automatically operate full face equipment from above ground were in the early 1980s. After successful automation of the face equipment, the emphasis is now on mine logistics. Autonomous monorail transport was introduced and tested in 2007. Since the development rate of machine improvements has its limits, the focus is on the full interaction of the total production system. Here information technology (IT) becomes important; the driver for more productivity. Actual developments aim for the complete and general homogeneous IT infrastructure both above ground as well as underground. The explosive environment needs high level investments in safe technology, eg access points for WLAN and fibre optics for underground use (ATEX certification). New technology availability also drives the enhancements of management and process control systems. Innovations in the mining industry often comprise technology advances through the adoption of well-known technologies. With virtual reality (VR) teaching and training systems advanced computational instruments, both in software and hardware development, were applied in the German coal mining industry for ten years. Widening lists of applications as well as the encouraging achievements show the economical benefits of investing in virtual reality technology both for teaching and training and for knowledge management. The paper discusses the actual technical achievements as well as in IT infrastructure utilisation and also in employment of virtual reality based systems. Special focus and deeper insight will be given to the fibre optics and WLAN hardware integration as well as software developments. The pocket personal computer (PC) is used to enhance underground material transport and data acquisition. The knowledge-based maintenance system (KBMS) integrates real-time virtual reality knowledge elements, such as repair process descriptions. It gives access to expert documentation by intelligent search algorithms and 3D representations of major mining machinery.

Jan 1, 2008

By M Flanagan, T Sua, B Wright, T Carroll, B Van Dijken

"BHP Billiton (BHPB) West Australian Iron Ore (WAIO) conducts an extensive geometallurgy (geomet) program for its iron ore deposits in the Pilbara. The geomet program provides accurate information to infrastructure engineers, resource geologists, mine planning engineers and the technical marketing team on the performance characteristics of iron ores. Performance metrics include production planning, such as lump/fine splits, processing capability such as the level of ultra-fine iron ore and ironmaking blast furnace properties including tumble index (TI) and reduction disintegration index (RDI). Prior to the introduction of the current geomet program in WAIO, basic geometallurgical information was provided at the deposit level, such as deposit lump percentage and head grade chemistry. As the business value of geometallurgy was realised during the growth period of WAIO, the geomet process was reviewed and formalised into five steps: geomet drill planning laboratory measurement data management algorithm development block estimation.The geomet laboratory process produces simulated iron ore products from drill core, which are then subjected to physical geometallurgy test work. With the large amount of geometallurgy data collected, extensive databases are utilised to collate and organise the data to improve its usability within the business. Algorithms are created from the data to predict important geomet variables and a block estimation method is used to estimate geometallurgical properties into resource models. The predicted geometallurgy data is regularly reviewed at the different steps against plant and shipping data to allow refinement of the geometallurgy algorithms. It is also recognised that geomet data can be used to optimise the operations in existing processing hubs for improved production rate. In addition, future geomet programs will focus on generating data from all available drill core programs, not just dedicated geomet drill holes, and will incorporate new types of data, such as hyper-spectral information, for improved geometallurgical estimation.CITATION:Wright, B, Carroll, T, Flanagan, M, Sua, T and Van Dijken, B, 2013. BHP Billiton West Australian iron ore geometallurgy - past, present and future, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013, pp 105-110 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Sep 29, 2013

By Nakahiro Y, Wakamatsu T

In the present study, from experimental results, a new concept of possibility of flotation separation of quartz from feldspar is presented. The effect of the nonionic surfactant Brij 58 on the flotation behaviour of quartz and feldspar has been investigated. The effect of the surfactant adsorption at the solid-liquid interface was also studied. The results demonstrate that maximum flotability of quartz occurred at low concentration of surfactant. Feldspar is not collected by this surfactant. Flotation tests with feldspar that had previously been subjected to leaching by hydrochloric acid yielded similar flotation response as that of quartz. The effect of removal of alkali cations from feldspar surface on its flotability was investigated. The effects of inorganic and organic additives on the flotation recovery of quartz are discussed in terms of the slating-out or salting-in properties of these additives. KEYWORDS: Alkyl polyoxyethylene; feldspar; flotation; nonionic surfactant; quartz; salting-in; salting-out; separation; silanol groups.

Jan 1, 1993

By H Utama, R Heryadi

PT Indo Muro Kencana (PT IMK) is a surface gold and silver mine located in Mt. Muro area, Central Kalimantan province, Indonesia. The mining operations of multiple open pits using combination of excavator and haul truck is operated. This operation is performed in two shifts in a day. The articulated dump truck (ADT) with capacity of 40 t and 60 t deliver ore to the mineral processing plant and discard waste material to the waste dump area. Overall, PT IMK’s mining operation department is consisting of two sections, namely mining operation section and drill and blast section. Firstly, mine operation section is responsible to manage loading, hauling, pit service (mine dewatering, earthwork, road maintenance) and mine operation engineering. Secondly, drill and blast section is in charge to manage drilling and blasting (blast engineering, blasting operation, explosive permit and magazine or explosive storage). Additionally, conventional blasting method (ore-waste blasting) with non-electric initiation system is used and sleep blasting is undertaken as bulk explosive is buried for maximum two days. The first purpose of this paper is to elucidate about role of mining engineer in mining operation department (mining operation engineer and D&B engineer). At this point, mining operation engineering practice (fleet management system, production control and mining manpower management) and also blasting daily practice will be elucidated. Daily blasting practice is consisting of surface blast design, explosive engineering, sleep blast practice and the concept of scaled depth of burial to ensure a safe work environment in blasting activity. Next, the second purpose of this paper is to explore workforce evolution and future skills for mining engineer in surface mining operation. Furthermore, strategy to advance future skills such as mining continuous improvement program, training and skills development for mining engineer (mining operation engineer and D&B engineer) in order to develop their skills is also discussed. It is expected that in the future, these future mining leaders will become new mining leader, for instance mining superintendents, D&B superintendents and mining managers. In conclusion, it is clear that awareness about workforce evolution, professional development, training, skills development, mining economics awareness and mining continuous improvement program are essentially required as professional development for mining engineer (mining operation engineer and D&B engineer), in order to be commercially competitive in their future career and in order to be adapted with future workforce evolution in mining.

Sep 1, 2024