Search Documents

Societal expectations about how the industry operates and treats its people will be a key driver in the development of the Australian mining industry over the next 20 - 30 years (Moffat, Mason and Littleboy, 2009). Understanding these expectations will be critical in maintaining what much of the minerals industry calls its 'social licence to operate', or its public acceptance or approval. Yet what constitutes this social licence is poorly articulated, with little published research exploring the concept at a local operational level or at the national level in Australia or internationally. This research aimed to explore the societal expectations of the mining industry in Australia and test a participatory methodology to articulate them. Three workshops were conducted with a sample of 24 members of the 'Australian voting public' to explore community objectives for the onshore exploration and mining industry, and the underlying expectations for how the industry should operate in the future. Qualitative analysis of this data revealed three overarching objectives for the onshore mining industry held by participants. They thought that the industry should: advance Australia's national interests (including social well-being); minimise environmental impact, and; act in a socially responsible manner. Within each of these three key themes, or objectives, a number of tensions were evident in the views of participants regarding the trade-offs they are willing to make to secure economic benefit from mining, as well as the basic conditions for socially acceptable mining. These data provide an insight into the conditions for a national social licence in Australia for the mining industry, and the means for its realisation.

Jun 1, 2010

This paper sets out to discuss how alluvials - particularly mineral sands, tin and gold have adjusted to meet the problems of lower grade and more difficult physical political and economic conditions. The mineral sands industry seems to have adapted satisfactorily but less so with tin and gold.

Jan 1, 1996

By R Sinclair, D Landwehr, I Hunter

"The Syama Gold Mine, located in southern Mali, was established in 1990 by Broken Hill Propriety Limited (BHP). The operation began treating oxide, and in 1994 it transitioned to processing hard and refractory ore based on ‘whole-of-ore’ roasting. In 1996, BHP was succeeded by Randgold Resources and the operation ran until 2001, when it was placed into care and maintenance.The Syama ore is classified as a double refractory ore with pyrite occluding the fine grained gold present in the ore and high levels of organic carbon presenting a challenge in terms of preg-robbing behaviour. The ore is extremely competent and this combination of metallurgical features was the main source of metallurgical problems encountered by the previous owners.Resolute Mining Limited (RML) acquired the Syama project in 2004. Following a feasibility study and the development of a revised processing flow sheet the plant was recommissioned in 2008 using a combination of old and new equipment. The revised flow sheet enabled primary sulfide ore to be treated by flotation and roasting of the concentrate to produce a calcine suitable for conventional carbon-in-leach (CIL) processing.Commissioning and ramp up of the plant was a troubled process, with monthly gold production being as low as 3000 oz in 2010. Poor availability of equipment and lower-than-forecast recoveries were the primary contributors.During the last five years, RML has utilised a systematic approach to improve production, focusing on mechanical reliability, metallurgical recovery and process bottlenecks. Modifications to the circuit have been as a result of both innovation and the application of technological improvements. Improvements have been made to the flotation, roasting and CIL circuits and RML has introduced a deslime circuit to treat flotation concentrate, in addition to the very successful commissioning of a new 1 Mt/a oxide circuit in December 2014. These changes have resulted in gold production increasing to more than 20 000 oz per month in 2015.This paper presents the processes, change implementation and outcomes of the modifications made to the sulfide circuit to address the availability and recovery problems.Apart from the expansion of an existing, world-class deposit and discovery of new resources, future improvements on the path to a class-leading gold mine include the continued reduction of the unit cash cost, increase in overall sulfide circuit gold recovery, increased throughput through continued innovation and consistency in the plant’s operation.Citation:Sinclair, R, Hunter, I and Landwehr, D, 2016. Syama Gold Mine - the Journey towards a Class-leading Gold Mine, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 213–224 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By D Blair, T Scutts, L Fergusson

This paper presents a waste rock treatment and rehabilitation program conducted at a metaliferous mine site in northern New South Wales from 2000–2013. It updates findings from 2005 for Program #1 (which examined acidity, leachable metals and tree growth in a control and three treated areas of waste rock) and includes new results for Program #2 (which examined acidity, plant uptake of metals and trace elements and tree growth in a control and four treated areas compared to undisturbed background levels) and Program?#3 (which examined the treatment and revegetation of submerged mine tailings and an exposed tailings beach).Program #1 showed low soil pH in the control area remained unchanged from years 1–14, and soil pH in the limed and capped areas was initially increased but fell back to starting levels within 12 months and remained low for 14 years. In contrast, soil pH in the Terra B area resulted in soil high pH immediately after treatment and increased in years six and 14 without further treatment. Tree height and density in 2005 and again in 2013 indicated acidity in the control, limed and capped areas suppressed tree height and density; however, in the Terra B area, revegetation in 2013 was comparable to undisturbed forest. Outcomes in the control, biosolids and three Terra B areas in Program #2 were similar to those observed in Program #1.Program #3 showed the submerged and exposed tailings initially had low pH and high concentrations of total and leachable metals before treatment, but these became non-leachable after treatment with Terra B. Revegetation was achieved on the tailings beach, with almost uniform colonisation of bulrush and common reed, along with bottlebrush and golden wattle; a variety of reptiles have also been observed on the revegetated tailings beach, along with migrating ducks, spoonbills and grebes.CITATION:Fergusson, L, Blair, D and Scutts, T, ?2014. Treatment and rehabilitation of acidic waste rock and tailings – a 14-year case study, in Proceedings Life-of-Mine 2014 , pp 247–260 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

By M Bilodeau, G Caro, R Beaudoin, D Labrie

In 2005, Dyno Nobel Canada Inc, DynoConsult and CANMET-MMSL used their pool of expertise in blasting, ground control, open pit and underground mining, mineral processing, information technology and applied mineralogy to launch a research project aimed at evaluating the role of electronic detonators in the development of a sustainable energy-efficient rock reduction process. The overall objectives were to improve health and safety in a mining environment and reduce energy consumption and greenhouse gas (GHG) production in the Canadian mining industry. The study was conducted in a quarry located in Nova Scotia, Canada, with the objective of taking advantage of the higher accuracy and flexibility of electronic detonators towards improving blast efficiency and measuring its impact on productivity in a quarry environment and energy savings. Optimising the blast sequence was the first aspect to be considered before starting to look at designing bigger blasts and achieving productivity improvements, without creating additional environmental concerns, as the quarryÆs location was representing a challenge in itself in the surrounding community. The use of high-speed cameras (500 fps) was an improved means of analysing blast dynamics during the firing sequence. Seismic monitoring and linear superposition techniques were also applied to validate the sequences to be tested in all three specific geological areas. The combination of field measurements allowed to identify the optimal blasting sequences that would then be delivered accurately with the electronic initiation systems. The data from 12 blasts (six with electronic detonators and six with pyrotechnic detonators) carried out in three different geological formations (soft, medium and hard rock) showed that the electronic blasting technology could increase rock fragmentation by 15 to 20 per cent. A more uniform distribution of rock fragment size was also obtained. Blast improvements on downstream processes resulted in a five per cent productivity increase in rock excavation and transportation, a ten per cent energy reduction in primary crushing and a 15 per cent increase in the primary crusher throughput. A prototype soft-sensor based on primary crusher data (eg energy consumption, throughput, feed and product size distribution) and a simplified computer process model were developed for online measurement of a rock operating work index. Furthermore, rock samples were collected and specimens were prepared in order to determine the tensile and compressive strength of the rock materials, evaluate the aggregate crushing work index and examine the development of micro and macro-fractures under binocular and scanning electron microscopy (SEM). Blast-induced rock damage was evaluated at the end of the laboratory testing program. A reduction in rock hardness by about 30 per cent was observed after blasting. However, the impact of the blasting method (eg using electronic versus pyrotechnic detonators) on the induced rock damage was either absent or not perceptible within the measurement technique accuracy and the number of samples analysed.

Jan 1, 2007

By P J. Cullen, B P. Banerjee, S Raval

Continuous monitoring of mining impacts on the surrounding environment is a necessary sustainability criterion. Traditional monitoring approaches such as in situ sampling and airborne and satellite-based remote sensing have several limitations. Over the past few decades, unmanned aerial vehicles (UAVs) have evolved into popular platforms for remote sensing. UAV-based remote sensing has been successfully applied in different sectors, including agriculture, forestry, urban environments and disaster management. However, the potential of UAVs for mine environmental monitoring has not yet been fully established. This paper envisages the use of UAVs and sensor systems to monitor the environment of future mines.CITATION:Banerjee, B P, Raval, S and Cullen, P J, 2015. Unmanned aerial vehicles for mine environment monitoring, in Proceedings Third International Future Mining Conference, pp 137–144 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 4, 2015

By Jowett A

To compare open circuit lead primary rougher results at Mount Isa Mines Ltd., eleven surveys were made over five weeks of plant operation with varying ore sources, including a specially hauled sample of 100% Black Star ore. Three of the surveys which represented extremes in performance were selected for sizing, cyclosizing and assaying for lead, zinc and iron. A comparison of the flotation kinetics has revealed the similarities (including common problems) and differences for the surveyed ores. The concepts of entrainment and collectorless flotability are used to aid interpretation of the kinetic data.

Jan 1, 1978

By J Siliézar

The Ernest Henry Mine (EHM) is situated 38 km north-east of Cloncurry in the Mount Isa – Cloncurry mineral district of northwest Queensland. The EHM orebody is an iron oxide copper gold deposit with an average grade of one per cent copper, 0.5 g/t gold and 23 per cent magnetite, with current reserves of approximately 88 Mt.The copper concentrator is a single line plant with a nominal throughput rate of 1300 tonnes per hour. An average of 350 000 tonnes of concentrate is produced each year containing around 100 000 tonnes of copper metal and 120 000 troy ounces of gold.In December 2009, Xstrata Copper announced approval of a $589 M investment to extend the life of EHM to at least 2024, through the transformation of open pit mining operations to a major underground mine together with the construction of an associated magnetite extraction plant.The EHM magnetite plant extracts the magnetite from the copper concentrator’s tailings stream. It will produce approximately 1.2 Mt of magnetite concentrate per annum at full capacity for export to Asia, making EHM Queensland’s first iron ore concentrate exporter. Construction of the magnetite extraction plant commenced in July 2010 and was completed in January 2011.This paper gives an overview of the development of the EHM magnetite extraction plant flow sheet from the early mineralogy and laboratory test work through to the plant commissioning and early operation of the base plant. It has a major focus on the commissioning learnings from the plant start-up and includes a review of the operational performance of the plant versus original design and expectations.

Jul 11, 2011

By D Yates, C C(te, M Rodgerson

This paper describes how specific technical and regulatory issues related to water management have been dealt with at Anglo AmericanÆs Moranbah North mine. It compiles the collection of practices that have been implemented since 2010 in response to climatic and regulatory drivers. Operations must continually evolve as they face emerging challenges. For Moranbah North mine, one key challenge is the integration of its mine water system to that of its new neighbouring mine Grosvenor. The commitment to ongoing improvement has placed the mine in a good position to face this particular challenge.Water-related risks were identified then mitigated by technical practices, which have focused on improving underground water management, increasing storage capacity and installing a state-of-the-art control system for the management of water on-site and for releases of mine-affected water to the environment. These practices are supported by an extensive monitoring and audit system that provides confidence in the reporting of activities and outcomes. The strategy has helped the operation with its continual attempts to minimise reliance on high-quality third-party water and improving its interaction with the surrounding environment and community.CITATION:Rodgerson, M, Yates, D and C(te, C, 2013. Leading practice water management at Moranbah North Underground Mine, in Proceedings Water in Mining 2013 , pp 301-310 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 26, 2013

By M Spleit

A long-term production schedule for the LabMag iron ore deposit in northern Quebec, Canada is derived using stochastic integer programming. The optimisation formulation maximises the schedule’s net present value while simultaneously managing the risk of deviations in production tonnages and qualities by considering stochastic simulations of the orebody instead of a single deterministic model. The formulation also smooths and minimises haul truck requirements and ensures that as mining progresses, space is created within the mined out pit for the return of waste material.CITATION:Spleit, M, 2014. Production schedule optimisation – meeting targets by hedging against geological risk while addressing environmental and equipment concerns, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014, pp 397–404 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 24, 2014

By Q Zhou, G Barrett, Y Choi, J Jiang

As part of a general review of processing double refractory ores through Barrick GoldÆs autoclaves /carbon-in-leach (CIL) facility at Goldstrike, a study was made to evaluate the use of surfactants for reducing the loss of gold during cyanide leaching of preg-robbing gold ores. Consistent improvement of gold recovery was observed with surfactants at various testing conditions. This paper will discuss the results obtained from laboratory and pilot-scale testing, as well as, review potential mechanisms for the observed improvement in gold recovery.CITATION:Zhou, Q, Barrett, G, Jiang, J and Choi, Y, 2013. Surfactants for gold recovery improvement with preg-robbing gold ores, in Proceedings World Gold 2013 , pp 367-372 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By G Morgan, C Kemp

In December 2010, a trial of borehole radar technology was conducted to test the usefulness of the technique in better refining the position and geometry of narrow vein orebodies away from the primary data sources of drilling and mapping of development excavations. This paper summarises the reasons why the technique was applied, describes the testing methods selected and summarises the outcomes of the trial.Poor reconciliations of recovered metal from a section of an orebody at Jundee mine site, Western Australia, led to an investigation that identified insufficient understanding of the geometry of a narrow vein orebody as a potential cause. This orebody was situated between mapped development excavations and away from surrounding drill holes. Borehole radar was identified as a possible technique that could supply information on vein location and continuity away from other data sources allowing more accurate orebody modelling and subsequent stope optimisation.A borehole radar instrument (10 - 100 MHz frequency) was inserted into pairs of purpose-drilled boreholes on either side of relatively well-constrained mineralisation and the radar reflection data was collected. This process was repeated in five locations across the mine to represent the most common geological settings, lithologies and orebody varieties encountered at Jundee to determine the suitability of applying the technique in each of these settings. Collected, processed and interpreted radar data was compared to other geology data collected independently for verification and interpretation.Conclusions drawn from the analysis were that the technique could effectively determine the following features of the mineralised veins in the majority of test environments: geometry of veins, magnitude of offsets where structures intersect and orientations of planar structures with short strike length. The technique was very useful in selecting the appropriate structural interpretation where available data could lead to multiple, equally likely, interpretations.CITATION:Kemp, C and Morgan, G, 2012. Using borehole radar to refine orebody interpretations in a narrow vein gold deposit, in Proceedings Narrow Vein Mining 2012 , pp 121-130 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 26, 2012

By E McLean

The decision making check-list and hierarchy of information for process and plant design is generally wide-ranging and complex. The nature of grades, mineralisation and ore types in an ore body, its mine development sequence, and the body of results from metallurgical and physical test work present complex and competing influences on flowsheet development, values for design, equipment selection, plant efficiencies and operating strategy. The challenge is how to manage all these variables, to understand their impacts on performance, and how best to provide a cost-effective plant design and robust process that meets daily/weekly/monthly operating objectives. Throughput, production and grade or product specifications need to be met. The ore body is not average; its range of metallurgical and physical characteristics may be moderately to highly variable. This paper assesses some of the key competing influences and conflicting issues in design and equipment selection, and their effect on production and performance expectations.

Aug 8, 2011

By J W. Dong, Y M. Li, J L. Tian, Z H. Jiang

Electroslag remelting is widely used to produce various special steels, mainly because of its ability to provide high cleanliness and excellent homogeneity of ingot. Undoubtedly an optimal slag plays a key role in removing inclusions and enhancing the mechanical properties of a specific special steel. In order to improve the metallurgical performance of the slag in electroslag refining of die steel, a variety of slags have already been developed using traditional trial-and-error methods. Nonetheless, these slags may not be inherently optimal for the specific requirements of actual die steel refining processes. In this work, we have designed a CaF2-CaO-Al2O3-SiO2-MgO quinary slag system using genetic algorithms method aiming to remove the existing large size inclusions (D and Ds type) in high quality die steel. The comprehensive effects of five components (CaF2, CaO, Al2O3, SiO2 and MgO) were studied based on existing fundamental theory. The slag composition was screened considering the parameters such as melting point, electrical conductivity, calcium ion concentration, and appropriate viscosity etc. Furthermore, the candidate optimal slag was applied in the industrial production of die steel by electroslag remelting method. The detection results indicate that majority large inclusions (D and Ds type) have been successfully removed, showing significant advantage to traditional slags. This result has demonstrated the genetic method to be efficient and reliable. In addition, depending on the personalised demand of other steel and alloys, this method allows for the adjustment of the screening frameworks and processes to develop the candidate optimal slags. This method has not been reported previously in the field of electroslag composition design, and compared with the traditional trial-and-error method, the new method will save a lot of time and experimental costs.

Jun 19, 2024

By D Andrew, G Stanway, P Mahoney, C Griebel

The iron ore mining industry is currently going through an adjustment from high to more moderate growth as China’s economy transitions from capital-intensive investment to a more services-oriented economy. We are now witnessing a renewed focus on productivity improvements and cost savings as planned expansions are completed. Despite the scale and importance that the mining industry plays in the global economy, innovation literature is generally more targeted at faster-moving industries with shorter innovation timeframes and lower capital requirements. To fill this gap, VCI set out to understand the state of innovation in the mining industry in 2014. This State of Play report aims to give an objective appraisal of the strengths and weaknesses of innovation in mining. The report has three sections covering both the structure and delivery of innovation in mining:Ecosystem – focused on understanding how the iron ore mining innovation ecosystem system works, including the roles of large and small miners, service companies, researchers and governments. Our recommendations focus on what is required for the system to work well and improve the level and quality of innovation in the industry.Strategy – how do companies define their innovation strategy in relation to their corporate strategy? How are these related to prevailing global and industry trends? How do they communicate this with their business? How successful are they? These are among the questions that this section attempts to answer. Our recommendations are pitched at the executive leadership of iron ore mining and service companies.Delivery – focused on how companies develop and deliver innovation, looking at the success of different structural options, leadership and culture, partnerships and the best approaches to change. Recommendations are aimed at improving outcomes within the iron ore mining value chain, including the role that suppliers play.CITATION:Stanway, G, Mahoney, P, Andrew, D and Griebel, C, 2015. Understanding the state of innovation in the iron ore industry, in Proceedings Iron Ore 2015, pp 631–646 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By O Arafat, R E. McIvor, K M. Bartholomew

It is well known in the industry that good classification system performance is vital to efficient ball mill circuit performance. But what is meant by good classification system performance, and how is it achieved? Unfortunately, the perceived complexity of classification systems, and the day-to-day time demands placed on the practicing metallurgist, all too often put the low-hanging fruit of classification system optimisation in the ‘I’ll do it later’ basket. Additionally, lingering confusion about basics such as the relationship between circulating load ratio and ball mill circuit performance makes the optimisation objective seem nebulous to both plant metallurgist and designer.Some of this confusion can be eliminated by taking a step back from the overwhelming detail of sharpness of separation curves, circulating load ratios, cyclone feed pressures, vortex and apex sizes etc, and focusing on the purpose or function of the classification system – to apply mill power to particles that need further size reduction! The classification system efficiency (CSE) metric captures how well the classification system is performing its function with two quick and easy size distribution analyses.Once CSE is understood and implemented as the optimisation criteria, well-tested methods for improving CSE can be implemented and quickly measured at plant scale to give confidence that the right change was made.This paper will describe CSE and how it is measured in practice. Next, a guide for improving CSE through manipulation of design and operating variables in the classification system will be provided. Examples and case studies will illustrate the gains in ball mill circuit efficiency that can be achieved by maximising CSE.CITATION:Bartholomew, K M, McIvor, R E and Arafat, O, 2018. A guide to maximising ball mill circuit classification system efficiency (CSE), for operators and equipment designers, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 553–558 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By L D. Redden, M G. Nelson

Mechanical flotation machine design is typically based on hydrodynamic analysis, with scale-up calculated by geometric proportionality. End users often specify and purchase machines on the basis of retention time, characterised by the æ$/m3Æ approach; they may also consider the manufacturerÆs installed base. In some applications, end users also consider specific energy and the impact of energy consumption on operational costs. In other cases, a decision may be based on machine type (forced-air versus self-aspirating) and perceived metallurgical or operational advantages of one machine type over the other. With regard to metallurgical performance efficient bubble-particle contact is very important and is primarily influenced by two factors:the concentration and size distribution of bubbles in the machineÆs contact zone (the volume enclosed by the disperser); and the number of times that slurry is pumped through the contact zone. The second factor is a function of the machineÆs pumping rate and its retention time. Field data show that pumping efficiency is independent of aeration rate. In this paper, a new dimensionless number for the characterisation of flotation efficiency is presented. The contact frequency number (CFN) is defined as the number of times a given volume of slurry passes through a machineÆs active contact region, and is given by: CFN Qp/Qf, where:Qpis the pumping rate through the contact regionQfis the volumetric feed rate to the machine

Jan 1, 2005

By Ho SE, Neil Phillips G, Houstoun SM

There are numerous individual gold deposits in the Archaean greenstone belts of Western Australia, but only 26 have productions and/or quoted reserves in excess of 10 tonnes Au. Most gold production has come from mineralization in shear zones, quartz veins or stockworks in volcanic or intrusive host rocks, particularly tholeiitic basalts or dolerites metamorphosed at sub-amphibolite facies (e.g. Kalgoorlie). Significant prod- uction has also come from BIF-hosted deposits (e.g. Hill 50), and large reserves are quoted for mafic hosts at high metamorphic grade (e.g. Big Bell). Most deposits have marked structural control, great depth extension, and are characterized by zoned alteration haloes of pyritization (with Au), K-metasomatism and carbonation. On the regional scale, most larger volcanic- or intrusive-hosted deposits occur in younger (ca 2.8 b.y.) rift-phase green- stones (Norseman-Wiluna Belt). These belts also have a high prospectivity (36 kg Au/km2 of greenstone belt). Younger (ca 3.0 b.y.) and older (ca 3.5 b.y.) platform-phase green stones of the Murchison and Sodthern Cross Provinces and the east Pilbara, respectively, are progressively less prospective (14 kg Au/km2 and 0.8 kg Au/km2, respectively) and also have progressively smaller deposits. The important regional- and local-scale characteristics of most gold deposits can be explained in terms of a metamorphic- replacement model. In this model, metamorphic H2O-CO2 fluids, focussed by faults and shear zones, infiltrated host rocks and deposit gold at 350 + 50¦C and 1-2 kb, largely in response to fluid-wallrock interaction. In many large deposits, gold precipitation was synchronous with sulphidation of Fe-rich host rocks, but the diversity and abundance of smaller deposits reflects the variety of reactions precipitating gold from ubiquitous, auriferous metamorphic fluids. Regional variations in abundance and size of deposits relate to factors such as tectonic setting, alteration styles and possibly source rocks.

Jan 1, 1986

At Cliffs Natural Resources Ltd (CNR) crushing and shipping sample stations, precisions are estimated for the sampling, preparation and measurement stages of iron ore sampling in accordance with ISO 3085 (2002). In this Standard, gross duplicate samples are prepared at each of the three stages, yielding eight measurement assays. Appropriate calculations of the differences between assay pairs are then made to estimate precision of each stage of sampling. The International Standard for checking precision in iron ore sampling, ISO 3085 (2002) prescribes a method for identifying outliers that is ambiguous and possibly inappropriate. The procedure also makes an unnecessary implicit assumption, that the differences between assay pairs are normally distributed. The Anderson-Darling statistic is used to demonstrate that in some cases the assay pair differences have distributions significantly different from normal. When applied at CNR as specified, the Standard leads to precision estimates well below the expected values, thus overestimating the sampling method's capability and limiting the opportunity for real process improvement. This paper suggests an improved method of estimating sampling, preparation and measurement precision. A bootstrap procedure is used to estimate confidence limits for the calculated precision estimates. The proposed method would be suitable for testing blasthole precision. The discussion is supported by extensive simulation modelling of realistic data.

Mar 1, 2010

By H Jones

Closure cost estimates may be generated at any stage of a mining operationÆs life; commencing with the initial prefeasibility studies and continuing through to the final decommissioning cost estimates. However, not all mine closure cost estimates are necessarily the same. Cost estimates will vary depending on the purpose for which they are prepared, the organisations requiring or undertaking the estimate and the stage of the mining operation. Different organisations can legitimately arrive at disparate cost estimates for closing the same mine because the organisations have different reasons for requiring the estimates. Another, equally valid, reason for potentially wide variations in cost estimates by different organisations on the same mine site is the different definitions of æclosure costsÆ used by different estimators. This paper considers the different approaches by different organisations including operating companies, government authorities and financial organisations and uses a hypothetical example based on practical experience to illustrate some of these differences in estimation methods.The paper suggest that a more consistent approach to closure cost estimating in the Australian mining industry would assist mining companies, governments, the accounting industry and the broader community to better understand this complex component of mine planning. One possible approach to closure cost estimating is briefly outlined.CITATION:Jones, H, 2012. Closure cost estimation - All things to all men?, in Proceedings International Mine Management 2012, pp 115-124 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 20, 2012