Search Documents

By V Matousek, A Sellgren, R Visintainer, G McCall

A 4-component model for settling slurry pipe flow has been previously described by Wilson et al (2006) and Sellgren et al (2014) to predict pipeline friction loss (hydraulic pressure gradient) over a range of slurry compositions: from fine to coarse particle size, narrow to broad particle size distribution, and low to high solids concentration. The method applies a weighted average of established pipeline models for various settling slurry flow regimes, according to the volume fraction of solids falling within the applicable size range for each model. Further development of the model was undertaken by Visintainer et al (2017a, 2017b), based on a comprehensive set of laboratory tests in 203 mm (8 inch) and 103 mm (4 inch) pipelines, and it was also adapted to the modelling of slurry pump performance derates. However, this work was all performed with solids having a specific gravity near 2.65, as is typical for many mineral processing and dredging applications. The goal of the present work is to test the applicability of these models for settling slurries having a higher solids specific gravity, as may often be seen in the mineral processing of iron ore deposits. To that end, a test program was carried out in a 103 mm (4 inch) pipe loop using various compositions of an iron ore product having a solids specific gravity of 4.75 and containing both coarse and fine solids. By screening and flushing operations, a range of particle size distributions were created having different proportions of the coarse and fine elements. In all, 19 tests were performed with d50 particle sizes ranging from 50 μm to 3.2 mm and delivered solids concentrations from 10 per cent to 43 per cent by volume. Particle size distributions varied from very narrow to very broad, with d85/d50 ratios ranging from 1.75 to 26. Pipeline pressure gradient and pump performance data were collected and used to test the applicability of the previously developed 4- component models and to propose improvements to the models for the handling of high-density solids.

Nov 8, 2021

By KEITH BARRONI

In the proposed criterion for coal a distinction is made between brittle and "psuedo-ductile" failure. This criterion is the basis for the development of new equations for coal pillar strength, including a transition from brittle fracture to pseudo-ductile yielding. In addition the equations obtained allow the critical minimum pillar dimensions to be calculated to avoid "catastrophic" and "ultimate failure".The validity of these formulae can be tested by comparing their results with pillar case histories derived from the literature.

Jan 1, 1988

By J M. F Clout, E Donskoi

The ability to design a beneficiation process for a new orebody based on particular feed characteristics is a powerful and practical tool. A new technique has been developed where beneficiation outcomes can be calculated by combining feed size-by-size chemical analysis, mineralogy, liberation and particle characteristics with a series of simple theoretical unit separation models rather than a simple mass balance approach or an exhaustive beneficiation test program. The new technique provides the ability to rapidly identify ore types that have the potential to meet product specifications whilst also rejecting others that will not meet specification even if a perfect separation was achieved. Beyond the broad scale decision making process, practical mineral separation curves from actual plant data can be used to more closely simulate the proposed process. This approach reduces the amount of laboratory and pilot plant work necessary by targeting what process stages will be required, increases early rejection of uneconomic options, identifies problematic ore types or unit operations and is a step towards estimation of final grade and recoveries achievable in potential circuit configurations.

Jan 1, 2004

The recent paper by Dr. Edwards upon the copper deposits of Australia furnishes a perspective upon that portion of the Commonwealth's mineral deposits which is the more welcome because it has been long overdue. The paper yields in compressed form and in handy arrangement for reference the more relevant data to end of 1938 for all of Australia's important copper deposits 'past"and. present, and for many of the lesser ones. The information supplied 'obviously' has 15een collected' painstakingly and compiled with discrimination.Such published surveys of a national character have been far too few.The Mineral Resources Survey branch of the Department of Supply and Shipping at Canberra has been engaged for several years upon comprehensive compilations of data concerning each of the more important minerals used in industry. Presumably the results will be published after the war. The group will constitute an impressive and valuable series.As yet the work has not been completed, and, for security reasons, much of that which has been finalized is not publicly available. This makes the paper by Dr. Edwards the more timely.In the compilation of data by those not acquainted at first hand with many of the districts involved it is inevitable that, from reading of the literature alone, certain misconceptions will arise relationships become confused; and some of the more recently acquired information unavoidably fail to be taken into account. One need only compare his own impressions of a district, gained from reading the published literature prior to inspection, with the impressions later arrived at following a visit, to realize the difficulties in appraising the various features,in their proper relationships.On the whole, Dr. Edwards has, kept such misinterpretations at a minimum, which is a tribute to the care he must have exercised in analysing the vast fund of data perused. A few errors of statement, mainly concerning, Queensland deposits, have been noted. None is vital, but in the interests of accuracy it seems well to point them out.QUEENSLANDMount IsaOn page 108 Mount Isa's prospective output of 12,000 tons of copper per year is stated as coming from the Doherty section (O'Doherty, Black Rock mine, R.B.),- the copper ore-body is said to occur in dolomitic limestone (-Page 110)-, and Mount Isa's copper output for 1938 from that source is given as 22 tons. On page 145 the same prospective copper output is stated as coming from a body lying out in the hanging-wall of the silver-lead-zinc...

Jan 1, 1943

By J Geronimo, P Kumar, Z Yussupova, M Yahyaei, M Powell

This work goes beyond the general perception of how the well-known mine to mill process can be applied, by applying deeper knowledge along the mining chain. Grade deportment and dilution are considered at the mining stage, and modelled with the new SMI blast movement simulator, linking with the block model data. Assessing the shift to a considerably more competent section of the orebody is quantified via substantial milling trials at standard and higher-intensity blasts. These were stockpiled for batch processing through the mill to ensure feed integrity. The trial work included operating the mill at widely different fillings to develop Grindcurve milling responses. Additionally, model informed process control is initiated via a mill prediction tool.It has been found that accounting for blast movement for the higher intensity blasts could generate additional value of around $1.5M per blast. With the high-intensity blast and changing mill control, the plant was easily able to exceed projected mill throughputs with the far more competent Pipeline ore. Strategies to shift the workload and debottleneck the milling circuit were proposed and proven during the milling trials, demonstrating an increase in throughput of 7 per cent despite running at a lower SAG mill speed, and potential of 16 per cent for increasing the SAG mill to standard operating speed. A number of process improvement opportunities have been identified to enhance current productivity and ensure long term capability to process the considerably more competent future ores. All of this is being linked in with the major digitisation program at the Barrick Cortez site, with an objective of linking all the data into a mine-wide process optimisation system, that can embed the processes by providing process-wide data access and production support via the future dynamic models linking ore body knowledge to productivity along the full process chain.CITATION:Powell, M, Yahyaei, M, Geronimo, J, Yussupova, Z and Kumar, P, 2018. The designed approach to mill liner optimisation – experience at Pustynnoye mine, Kazakhstan, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 595–612 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By M Bloss, B Roberts

BHP Billiton Olympic Dam required a well-tested software product suitable for strategic optimisation and scheduling of options for a potential underground mining project. The company has a standard software package called Blasor® that is used for open pit optimisation of complex deposits such as iron ore, copper-gold-uranium and silver-lead-zinc. It applies a mixed integer programming formulation (MIP) to produce conceptual pushback designs and an optimised pushback sequence. Schedules can then be run on the resulting mine designs. Existing pushback designs can also be imported into the model and an optimum schedule generated. One of the key advantages of Blasor is that multiple strategic mine schedules can be quickly generated according to the various scenarios, options and constraints that are being investigated.It was realised that Blasor, if carefully configured, could be adapted for use in underground planning. The concept of using Blasor as an optimiser for underground strategic scenarios is to represent the underground stope and development data in the form and structure of an open pit mine. In simple terms, underground stoping areas are modelled in the form of pushbacks (phases) with vertical walls. The phase dependency tools in Blasor are used to link mine blocks and their access development drives. These underground phases are imported into the optimiser. Artificial block models are constructed using stope design tonnage and grade data at various fixed cut-offs. A variable cut-off grade model has also been developed using a method of parcels to represent each cut-off grade increment.So far, this approach has been successfully used to investigate the optimum stope design cut-off for various strategic options, the economic potential of a series of mining and processing configurations and to provide guidance on the optimum sequence for developing and mining the various stoping blocks in the resource. Examination of the results has highlighted the most suitable development paths for more detailed study.CITATION:Roberts, B and Bloss, M, 2014. Adaptation of an open pit optimiser for underground strategic planning, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014 , pp 249–256 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 24, 2014

Common brattice cloths in use in Australian coal mines are compared by permeability measurements. The respective advantages of twill weave and tarpauling* weave cloths are listed, and the improvements to be obtained in the ventilation of a mine by using tarpauling cloths instead of the commonly used twill cloths are stressed. Plastic cloths are widely used overseas and are briefly discussed.INTRODUCTIONThe onset of extensive full-scale mechanization in Australian coal mines during the past few years has increased attention given to the ventilation of working places. Many inadequacies of the present system have been brought to light and not the least of these is connected with the use of brattice cloth, both in directing the flow of air around the face and in acting as a temporary sealing mechanism. A well-constructed line of brattice will only provide fair ventilation for a distance of 100 ft. Beyond this point the volume or air reaching the face falls off rapidly.Some of the shortcomings associated' with the use of brattice cloths are:1. Hurried installation, necessitated by a rapid advance, often results in poor workmanship with, consequently, an excessively high leakage rate.2. High places caused by falls of roof are difficult and time-consuming to seal.3. Curtains, in lines of brattice crossing transport routes, are difficult to maintain.4. Lines of brattice interfere with rock-dusting and clean-up of fine coal.5. Repair and maintenance of brattice consumes much...

Jan 1, 1959

By S McGregor, J Sharp, I Entezari, T Boulter

The piezocone penetration test (CPTu) is one of the primary screening tools used by the mining industry to evaluate whether tailings are susceptible to liquefaction (static or cyclic). Liquefaction analysis using the CPTu is influenced by the fines content of the soil, and most CPT screening tools empirically use the behaviour type index (Ic) to correct for fines. The issue with this approach is that such empirical relationships have been developed using data collected from natural soils and their applicability to different tailings deposits needs to be studied. In this paper, we explore the use of machine learning to develop a site-specific model to estimate fines content of tailings using gamma piezocone penetration testing (GCPTu) measurements. The results are then compared to the fines content derived from the soil behavior type index (Ic) proposed by Robertson and Wride (1998). A dataset of paired GCPTu and laboratory results were compiled and a support vector machine (SVM) algorithm was employed to calibrate a model to estimate tailings fines content from in-situ GCPTu data. We calibrated GCPTu data to geotechnical 75 μm fines content measured in the laboratory. The geotechnical fines content is the fines content as a percentage of solids. The development dataset was comprised of paired GCPTu-laboratory results collected in 2009-2019 from a mining area with predominately clay mineral and quartz sand tailings. Results show that the developed model predicts the geotechnical 75 μm fines content of the studied deposits with 7.8% error. The Ic based method estimates the fines content with 31% error. Evidently, the Ic method is not applicable to the studied tailings deposits. It is appreciated that many tailings fines do not contain clay, and that the success on this program may not be repeatable everywhere. However, the authors wish to point out that the application of site-specific machine learning algorithms may be used to significantly improve empirical geotechnical parameters.

Jul 1, 2021

Notwithstanding full concurrence with the dictum of a famous scientist that "definitions are the most accursed of all things on the face of the earth," in view of the considerable confusion which exists in jigging nomenclature, it is considered advisable to commence this paper with the following explanations of the terms which will be used throughout the text.Jig Bed. The whole layer of material lying on top of the jig screen.Ragging. The layer of denser material lying immediately above the jig screen, which is too coarse to pass through this screen and is confined horizontally by the cells of the top grid.Ore Column. The layer of ore pulp between the ragging and the top-water.Top Water. The water, carrying fine material in suspension, which flOiWS over the surface of the jig bed.Hutch Water. The water added to the jig below the screen. (Except for the water discharged with the hutch concentrate, the "hutch-water" eventually becomes "top-water.")Feed Water. The water in the ore pulp fed to the jig.(This water becomes part of the "top-water.")Pulsion. The period of the jigging cycle during which the water is moving upwards relative to the particles in the jig bed.

Jan 1, 1937

By D François-Bongarçon

The theory of sampling (TOS), and therefore representative sampling, is based on three fundamental principles: sample correctness, which handles the search for non-bias; segregation, the effects of which must be eliminated or minimised; and variance control to help achieve the desired reproducibility. After briefly reviewing these very few, albeit essential first principles of Gy’s TOS, the state-of-the-art in TOS is examined through the prism of these principles and the prospects for the future are explored, with suggestions for further research where relevant. Regarding segregation, which is currently the focus of much research, new orientations are proposed. For correctness, which takes on a major importance when it comes to sampling devices, some new, important principles that have been put forth by recent research, are described in details.CITATION:François-Bongarçon, D, 2014. State of affairs and current research trends in theory of sampling fundamentals, including segregation and correctness, in Proceedings Sampling 2014 , pp 11–16 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 29, 2014

By R Schiller, E Chait

"Quebrada Blanca is a porphyry copper deposit located in the Eocene-Oligocene belt of Chilean Andes. Operation started in 1994 and original reserves for supergene mineralisation gave a life-of-mine (LOM) of 20 years; however, further exploration extended the LOM until 2020.In order to optimise the remaining five years of supergene resource, geometallurgical variables were added to the geological model including copper recovery and acid consumption. LOM plan encompasses finishing the phase number eight and the future development of phases 11 and 13.LOM lithologies include diorites, quartz monzonites, porphyries, igneous and tourmaline breccias. Main alterations are: potassic, phyllic and argillic. Litho-alterations or geometallurgical units were formed by combining five types of rocks with three types of alteration. According to statistical information, the deposit can be represented with 12 litho-alteration units, which cover 98 per cent of the LOM volume.For copper recovery information, there were 40 mini-columns tests made in order to obtain kinetics curves and copper recovery values after comparing the difference between head and tails grades. Acid consumption was obtained using an automatic neutraliser device-based test.Historical data said that copper recovery in pads after 450 days of irrigation is around 75 per cent of recoverable copper while acid consumption is around 5.5 kg/t.According to this study, lower recoveries are related with potassic-altered diorites and argillic-altered quartz monzonites with values around 60 per cent. On the other hand, best recoveries could be found in potassic-altered quartz monzonites and argillic-altered diorites with values closer to 80 per cent.It was also revealed that the most reactive rock is the potassic-altered diorite with 12 kg/t of acid consumption. This rock covers approximately 40 per cent from phases 11 and 13.The final geomet model was calculated using a program that relates each geometallurgical unit with a specific copper recovery and acid consumption value. Results found after comparing model-obtained information with historical leached pads data were used to validate the model.CITATION:Chait, E and Schiller, R, 2016. Adding Copper Recovery and Acid Consumption Variables to the Geological Model of Quebrada Blanca, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 257–266 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

THE following brief paper is submitted with a view to encouraging the exploitation of hitherto neglected 10w~ grade ore-bodies which are suitable for extraction by open-cut methods.The Corinthian North mine, situated 10 miles from Southern Cross, in the Yilgarn district of Western Australia, furnishes an example of low working costs, although operations are carried out on quite a limited scale.The body of quartz which is now being worked strikes N.W. and S.E., has a very slight underlie to the west, and lies between bodies of quartz-hrematite s,chist on the east and amphibolite on the west.So far as the property has been explored, it would appear that the underlying sulphide rises to within about 70 ft. of the surface in the northern end of the workings, and pitches away to the south at a grade...

Jan 1, 1915

By M Rattenbur, A B. Christie, S C. Cox

A new minerals initiative to increase the level of understanding of New Zealand's mineral resources and to promote the development of minerals began earlier in the year in a partnership pilot-project between Crown Minerals and the Institute for Geological and Nuclear Sciences (GNS). The project aims to gather a set of comprehensive geoscientific data and build a series of digital GIS packages to highlight New Zealand's mineral prospectivity. The pilot study was carried out at a regional scale, and is focussed on mesothermal gold mineralisation in the South Island. A significant amount of geological data and information was sourced from open file technical reports held by Crown Minerals and from various databases held by GNS and has now been compiled into a single GIS dataset, which will soon be made freely available to interested parties. In addition to this comprehensive data compilation, prospectivity modelling using Weights of Evidence techniques was undertaken to highlight those areas likely to contain ore deposits. It is clear from this study that the South Island of New Zealand remains highly prospective for mesothermal gold mineralisation. Many of the highly prospective areas, which also contain historic mine workings, remain open for exploration. The study not only highlights these areas, but also other areas where the potential for similar mineralisation exists, in all likelihood with no surface expression. The study has also highlighted the value of many of the open-file technical reports held by Crown Minerals and the need to carry out additional studies using this and other available data at a more detailed level, possibly as the basis for a web-based minerals information system.

Jan 1, 2002

The Round Hill gold-scheelite deposit is located three kilometres from Macraes Flat and approximately 60 kilometres due north of Dunedin, New Zealand. A mining feasibility study is currently being undertaken on the deposit by BHP Minerals (New Zealand) Limited, who are the managers and operators of a Joint Venture with Home Reef Mining Limited. BHP has a 70 per cent equity in the project area.

Jan 1, 1987

Ferruginous manganese deposits have been known at Ripon Hills since the late 1950s. The main group of deposits occur in an area 6 km by 5 km and these were extensively investigated by Longreach Metals N.L. during1971 and 1972 for possible commercial exploitation.Ripon Hills is a dissectcd fault plateau 350 m above sea level formed by the uplift of a block of gently dipping Proterozoic shales, cherts, and dolomite. The plateau consists of chert breccia which is underlain by massive dolomite. The shales which are ferruginous and manganiferous overlie the chert breccia but are now only preserved, in places, in the broad depression and valleys of the plateau.The ore deposits occur as supergene replacement of the shales and were investigated by geological mapping, grid percussion and diamond drilling, and bulk beneficiation testing. Iron and manganese oxides erraticallyreplace Shale accompanied by the leaching of other minerals. The ore is composed of fine grained pyrolusite intergrown with fine grained hematite and locally containing extensively altered bixbyite and braunite. Thegangue mineral is mainly kaolin.The average grade, using a 15 per cent Mn cutoff, was 19 4 per cent Mn and 25·9 per cent Fe for a combined drill-proven, indicated, and inferred tonnage of 56,000,000 tonnes. The average depth of this mineralization from the surface is 11 m. Using a cutoff grade of 20 per cent Mn the average grade was 24·6 per cent Mn and 23·0 per cent Fe for a combined tonnage of 12,000,000 tonnes to an average depth of 8 m.The substantial drop in reserves occurs because a high proportion of the mineralized material contains less than 20 per cent Mn.It was shown that whereas the lower grade ore, despite erratic fluctuations in grade, could be beneficiated to specification grade by crushing, screening, and conductivity ore sorting, the higher grade ore could be beneficiatedto specification grade by crushing and screening only. The utilization of the higher grade ore was considered to constitute a more viable operation.There is potential for high grade manganese ore to be discovered in the Ripon Hills area at the contact of chert breccia and underlying dolomite.

Jan 1, 1977

At Waiuta near Reefton there is a remarkable vein of quartz <1 m thick which, apart from small offsets on late-stage faults, is a sheet like body essentially continuous down-dip and along-strike for> 1 km. The vein strikes NNE and dips steeply west (032/78¦W). From 1906-1951 the Blackwater mine produced 740,404 ounces of gold from the vein, called the æBirthday ReefÆ, which was one third of the total production from Reefton Goldfield and the fourth largest gold mine in New Zealand. Within the mine the vein is disrupted into a series of northeast-plunging shoots by late-stage faults. Similar faults, but with larger displacements, were thought in the past to truncate the vein at the northern and southern ends of the mine. The implication of this fault dissection model is that offset remnants of the vein await discovery. This study investigated the geometry of the vein and its relationship to host-rock structures and late-stage faults. A new model considers folding and lithological variation in the host-rocks to be fundamental in controlling the scale and geometry of veining, but does not rule out the possibility of some late-stage fault dissection. The Birthday Reef truncates 200-400 m wavelength folds in Greenland Group host-rocks at c.10¦ angle, that results in variation in the structural properties of host-rocks along strike every ~1350-2500 m. The spacing of fold hinges in the wall-rock veins is equivalent to the strike length of historic mining, implying that the Birthday Reef is probably hosted in a single limb of a fold. Similar relationships between mineralisation and host-rock folds appear to be present elsewhere in the Reefton Goldfield (e.g. Capleston and Murray Creek group of mines). Exploration targets are located one fold wavelength (c.1350-2500 m) further along strike from the Blackwater mine and relatively barren rock is expected in between the mine and target areas. Refining the location of folds and different host rock lithologies, using geophysical data and quality geological mapping, is the key to reducing exploration risks and discovering further resources.

Jan 1, 2000

Two events during the past decade have combined to effectively alter the role of the geologist working in Papua New Guinea. The gold boom of the 1980s resulted in a substantial increase in the general awareness at village level of mining companies, gold and landowner issues, and as a consequence of the Bougainville tragedy, landowners are also very much aware of the potential problems of a mining operation in their area. Landowners know they have the power to remove a company from a project area, and government has shown itself to be virtually powerless and unable to help the company effectively. During a considerable proportion of a project's development time, the project geologist is viewed in the eyes of the local community as the 'company'. Good landowner relationships are nurtured over a reasonable time period and the input of the geologist is significant in determining the eventual fate of company-landowner relationships. The initial impressions of the company, gathered by the local community, will have a far reaching impact on the nature and direction of their future exchanges with the company.

Jan 1, 1991

The areas of concern lay in the processing of, and the subsequent hearing into, Waihi Gold's resource consent applications to extend Martha Mine. The proposed amendments to the Resource Management Act 1991 might see the introduction of contestability in the processing of applications - which would have assisted Waihi Gold; and the use of commissioners to hear the applications, with a right of appeal to the Environment Court on points of law only. It is also proposed to have major applications heard directly by the Environment Court. If Waihi Gold's applications had been heard at first instance by the Court, the delays in time and associated costs would have been reduced. However a hearing by commissioners only would not have been satisfactory, there being no right of appeal against the conditions of consent, which if implemented as granted by the Councils would have had a significant impact on the costs associated with the extended project.

Jan 1, 1998

As the question of zino recovery from lead blast furnace slags has lately become such an important subject with lead metallurgists, the following description of some of the work carried out in this oonnection by the Sulphide Corporation, at CockleCreek, should prove of interest to those concerned. Early in the life of the works it was realised by the metallurgical staff that a very wide field for investigation lay before them. At the head of these was the late Mr. F. H. Evans, and it was due to his work and suggestions that the question has grown from a mere hypothesis to a commercial undertaking, in so far as these works are concerned. A great deal of the early work was carried out in the form of small laboratory expe!iments, those giving the best results being ear-marked for subsequent trial on a larger scale. One of the main obstacles in the way of research was the lack of any data or information of similar work done in other...

Jan 1, 1920

By Kennedy G. L

Operating experience with the pilot Lurgi carbonization plant at Morwell showed that under conventional operating conditions, although the thermal efficiency of the plant was very' high, the physical quality of the char produced was extremely poor. By variation of operating conditions to produce the slow drying rate developed by the laboratory research at the University of Melbourne, an improvement in the size of the char was achieved. A similar approach in the carbonization stage where severe breakage of the briquettes still occurred was not possible due to insufficient control over the heating in this stage. Theoretical analysis of the heat exchange process has shown that severe heating of the briquettes entering the carbonizer is a characteristic of the Lurgi system and cannot be controlled by modified operation. The plant has been closed down for reconstruction of the heating system to enable it to be used to produce hard char.INTRODUCTIONAn experimental carbonization plant was operated at the Morwell Works of the 'Gas and Fuel Corporation from November 1958 until July 1959. This plant was built as a pilot plant by the Corporation to designs supplied by the Lurgi Gesellschaft fur Warmetechnik and had the nominal capacity to carbonize 25 tons of brown coal briquettes and to produce 11 tons of char per day. The briquettes were supplied from the· normal production of the Yallourn briquette factory and the 2t in. I-type briquette was the largest size which the plant could handle.This carbonization plant represents the intermediate stage of development between the laboratory research at the University of Melbourne and the commercial production of hard char as a metallurgical fuel. It is intended in the first place for the study of the technical problems in the handling and...

Jan 1, 1960