Search Documents

ENGINEERS AVAILABLE (Under this heading will be published notes sent to the Secretary of the Institute by members or other persons introduced by members.) Member, technical graduate, aged 36. Experienced copper metallurgist and mining geologist. Familiar also, through 15 years' broad practical experience, with mining, cyanidation, concentration (including oil flotation), metallurgical accounting, and mine and plant management. Best references. No. 237. Member, graduate engineer with 10 years' experience in malleable, gray -Iron, and steel, as chemist., metallographist, and metallurgist. Researches and investigations by laboratory methods and under works conditions. No objection to some routine. No. 243. Member, technical graduate, broad experience in coal, oil, and clay. Will go anywhere as mining geologist after Sept. 1, 1915. No. 244. Member, technical graduate, aged 30, married, with over 10 years' experience as chemist, engineer on construction, superintendent and general superintendent of bituminous coal and coke plants. SpeaksSpanish. References. No. 245. Member, open for engagement as mine safety inspector or as superintendent of bituminous coal mine. No. 246. Member, graduate mining engineer, with five years' experience in coal mining as mining engineer, construction engineer, pit boss, and superintendent, open for engagement. Best references. No. 247.

Jan 9, 1915

By R. K. Agarwal

In this paper, a new technique developed to analyze two-dimensional nonhomogeneous models is described. A simple three-layered medium with a circular hole centrally located in the intermediate layer is considered. The layered sheet is loaded uniaxially perpendicular to the stratification. The Young's modulus of the intermediate layer is lower than that of the outer layers. The stress distribution around the circular hole in a stratified medium is significantly different when compared to the case of a continuous homogeneous medium. The distribution depends upon the ratio of the height of the intermediate layer and the hole diameter. A comparison of stress distribution and procedures for preparation and testing of the model are given. The potential of the technique is outlined. In the process of applying the techniques of stress analysis to problems of rock mechanics, the recent discernible trend has been to postulate highly idealized models of physical situations. As new techniques have been developed, more complicated models have been conceived to simulate mote accurately the physical environment to which the analysis results are eventually applied. In this investigation, a new technique is developed to analyze two-dimensional nonhomogeneous models. The technique is used to determine the stress concentration around a circular hole in a soft material overlain and underlain by a hard material. In mining practice, such situations arise commonly in coal deposits and frequently in bedded or vein-type metallic mineral deposits. DEFINITION OF THE PROBLEM A plate, consisting of three layers with a circular hole in the intermediate layer, is loaded uniaxially, Fig. 1. The variable in the experimental investigation is the height of the intermediate layer, H. The diameter of the hole, D, is kept constant. The stress concentration factors around the periphery of the hole, for various values of H/D, are evaluated using the technique of photoelasticity, Table I. TECHNIQUE OF EXPLORATION Photoelastic analyses of composite models have hitherto been limited to the study of lap and butt joints between glued metals and dissimilar materials.1-3 In mining, Haber and Oudenhoven used composite models to study the stress distribution around a circular hole in two-layered media and the behavior of elastic liners in shallow underground openings.4-5 They used the stress freezing technique devised by Dally et a1.6 The procedure used in this investigation is outlined below: Casting of Layer A: Flat sheets of plastic were cast in a silicon-coated mold using Araldite 502 with hardener 951 in the ratio of 100:8 by weight. After

Jan 1, 1969

By H. V. Flagg

OPERATION of a modern steel plant presents a curious anomaly. Large-scale operations, in which large volumes or heavy weights of materials are involved, are not usually subject to close control or narrow specifications. On the other hand, operations that call for a high degree of precision are usually carried out under carefully controlled conditions with delicate, precise machinery and tools, and production is made secondary to quality. In a modern steel mill both extremes are taken as a matter of course. A strip mill making auto-body sheets must supply its customers with sheets that all come within a tolerance of plus or minus 0.003 in. in gauge at any point from side to side or end to end, and without blemishes either of color or surface. Sheets that were considered par excellence as recently as ten years ago could not even find a market today. Such exacting requirements have made necessary a nicety of control that approaches the watchmaker's art. Notwithstanding this necessity for precision, the scale of operation is stupendous.

Jan 1, 1940

By AIME AIME

EVEN the weather man joined in a friendly conspiracy to make the fall meeting of the Industrial Minerals Division at Rolla, Mo., Oct. 23-25. the splendid surges that it was. Following weeks of rain, the foliage of the Ozarks was still green, merely enlivened here and there by splashes of autumn coloring. In contrast to the tranquil beauty of the School of Mines campus under smiling Indian summer skies, the pace of the meeting was lively. Registration was larger than at any previous meeting and included an unusual number of prominent names and delegates from all over the country. From 125 to 150 were present throughout the three technical sessions, at the Thursday evening smoker, and also at the banquet on Friday; when students trooped in to the technical sessions the audience was augmented occasionally to over 200.

Jan 1, 1941

By T. Price, H. A. Holl, A. P. Greenough, A

UdIN, Shaler, and ulff' first used wires for the determination of the surface energy of a solid metal. A gage length was marked by tying knots in the wires, which were then suspended in a cylinder of the same metal, heated in an inert atmosphere for the appropriate time, cooled to room temperature, and finally removed from the furnace so that the lengths of the wires could be measured. With iron wires, difficulties associated with deformation during the phase changeszp3 made it necessary to measure the gage lengths at the tem-

Jan 1, 1964

By Charles H. Behre

KEYNOTE of the mining geology sessions was the preparation for an extensive war with all that this implies as to the need for strategic minerals, both metallic and nonmetallic. Nevertheless the sessions also included many papers of less urgent, more theoretical interest. The stress of wartime production had the effect of giving an unusually full and rich program, the longest in recent years, with sessions continuing virtually throughout the meeting. Some papers dealt with geophysical prospecting as applied to mining geology; others were concerned with the grand strategy of mineral reserves and thus involved the industrial minerals; such "borderline" subjects were presented before sessions held jointly with the Geophysics Committee or the Industrial Minerals Division.

Jan 1, 1942

The regular activities of the Institute are financed mainly by income derived from members' dues, from advertising in MINING AND METALLURGY, and from the sale of publications to the public. In addition, collateral activities and special projects are financed each year by means of income from endowed funds controlled and administered by the Institute. In the aggregate, the principal sums of these endowments amount to more than $530,000. An active effort is being made to increase the endowment funds of the Institute through a standing committee, of which H. T. Hamilton is chairman, and of which the other members are: W. H. Aldridge, George D. Barron, Cleveland E. Dodge, D. C. Jackling, Henry Krumb and J. V. W. Reynders. This committee feels that there exists a tremendous opportunity for the Institute to be of ever-growing service to the public, to the mineral industries, and to the profession. It welcomes suggestions as to names of men of means who are vitally interested in the mineral industries, and to whom the opportunity to make a contribution or bequest might appeal favorably if presented in the proper light by the committee.

Jan 1, 1941

Jan 1, 1969

By Steven Mitchell

BACKGROUND Homestake Mining Company began milling operations at the Bulldog Mountain Mine near Creede, Colorado in 1969. The Bulldog Mill, rated at 350 tpd, produces a bulk flotation condentrate assaying about 180 oz/T Ag and 20% Pb, from heads of about 16 oz/T Ag and 2% Pb. The circuit is straightforward with two-stage grinding to 1-5% plus 65 mesh, followed by rougher and cleaner flotation. Reagents used are Z-6, Z-11, Aerofloat 242 and Aero Promoter 404, with an Aerofroth 65-MIBC mixture for a frother. Additional information on the geology, mine and mill are available in references (1) and (2). A flow sheet for the mill and CIP plant together is attached as Figure 1. Final flotation tailings normally vary from 1.5 - 2.0 oz/T Ag. These tailings are cycloned to produce sand for underground backfill. After cycloning, the sands are repulped and given a final scavenger float. This sand scavenger recovers a small additional amount of silver which recycles back to the main flotation circuit. The tailings are recycloned and pumped to the mine or, if the mine cannot accept sand, to tailings. The majority of the silver in the flotation tailings exists in the fine fractions; cycloning upgrades the slimes and lowers the assay of the sand. The sand, after scavenging, typically assays 0.5 oz/T Ag, and the slimes assay about 3.0-3.5 oz/T Ag. From 1969 to 1976 all of the slime tailings and the sand tailings not used underground were impounded in a tailings pond located about

Jan 1, 1983

By TENNEY C. DeSOLLAR

TRADITION tells us that the earliest use of Alabama iron was to make shoes for the horses of General Andrew Jackson and his men during the first part of the nineteenth century. The first recorded incident in the making of iron was the request of U. S. Indian Agent Benjamin Hawkins "that a crew of blacksmiths be sent to the Creek Nation in the lower Mississippi territory." These frontiersmen made up the first body of pioneer iron makers in the territory. The first known blast furnace was built by Joseph Heslip in 1818 at Russellville, named after Major William Russell, who was General Jackson's chief of scouts. The Tannehill furnace was built in 1830 in what is now Tuscaloosa County and its ruins, as shown above, can be seen today.

Jan 1, 1937

By H. F. Seifert

THE classification and preparation of non-ferrous scrap metals is a subject of interest to every individual and corporation that employs in its processes of manufacture non-ferrous metals and alloys and accumulates in such manufacture scrap from these materials for disposition in the form of turnings, borings, short ends, punchings, clippings, grindings, washings, etc. All too frequently the disposition of such scrap is left to individuals who have no knowledge of the subject either from a metallurgical or a commercial standpoint, or both. Much money is thus lost which with a little more intelligent effort might be saved, and in this day of fierce competition and small profits such an opportunity cannot be ignored. The Mineral Resources of the United States for the year 1925, the latest issue available (Part 1, page 221), gives the secondary non-ferrous TABLE 1.-Some Secondary Non-ferrous Metals Recovered in the United States for the Year 1924-25 Material Short Tons Value Copper, including that in alloys other than brass.... 250,600 $ 71,170,400 Brass, scrap remelted 242,300 56,270,800 Lead as metal 112,4201 39,477,100 Lead as alloys 112,460 Zinc as metal 61,430 11,359,000 Zinc -in alloys other than brass 13,300 Tin as metal 1 7,950 35,165,400 Tin in alloys 23,000 Antimony as metal 1 } 3;794,000 Antimony in alloys 10,839 Aluminum as metal 17,700 24 Aluminum in alloys 26,300 ,816,000 Nickel as metal 19 1 1,518,000 Nickel in non-ferrous alloys 2,109 Total 882,600 $243,570,700

Jan 1, 1928

By P. W. Bridgman

DURING the war, the Navy undertook the construction, under my direction, of an experimental gun embodying features designed to lessen the cost and time of production. These experiments were initiated after representations as to their, desirability had been offered by myself, by the Naval Consulting Board, and by the National Research Council. The first drawings were made in June, 1917, and the experiment was completed in November, 1918. For the sake of clearness it will pay to recapitulate briefly the fundamental idea of gun construction. It is well known that if a hollow cylinder is subjected to internal fluid pressure, the maximum stress occurs in the inside layers, the outer parts carrying much less than their due share of the stress. This inequality of stress is more pronounced the thicker the walls of the cylinder. If such a cylinder is pushed to the elastic limit, failure in elasticity will take place long before the outer layers have reached the limit of their capacity. Economical use of the material would demand, however, that all parts of the cylinder reach the limits of their capacity simultaneously. This may be brought about, at least in cylinders of not too great thickness, by producing in. the inner layers an initial compression, and in the outer layers an initial tension. The effect of internal pressure is at, first to relieve the compression of the inside layers, while increasing the tension of the outside layers. If the initial stresses are properly distributed, all parts of the cylinder will reach their elastic limits simultaneously, thus giving a cylinder of maximum strength for its weight. In gun construction as hitherto practiced, this initial distribution of stress is produced either by winding the inner tube with wire, a common English practice, or by shrinking hoops over the inner tube, which has been the standard American practice. Either process is long and expensive, particularly with the larger guns, 12- or 14-in., which require

Jan 2, 1920

By H. F. Seifert

THE classification and preparation of non-ferrous scrap metals is a subject of interest to every individual and corporation that employs in its processes of manufacture non-ferrous metals and alloys and accumulates in such manufacture scrap from these materials for disposition in the form .of turnings, borings, short ends, punchings, clippings, grindings, washings, etc. All too frequently the disposition-of such scrap is left to individuals who have no knowledge of the subject either from a metallurgical or a commercial standpoint, or both. Much money is thus lost which with a little more intelligent effort might be saved, and in this day of fierce competition and small profits such an opportunity cannot be ignored. The Mineral Resources of the United States for the year 1925, the latest issue available (Part 1, page 221), gives the secondary non-ferrous TABLE 1.-Some. Secondary Non-ferrous Metals Recovered in the United States for the -Year 1924-25 Material Short Tons Value Copper, including that in alloys other than brass.... 250,600 8 71,170,400 Brass, scrap remelted : 242,300 56,270,800 Lead as metal : 112,420 39,477,100 Lead as alloys 112,460 Zinc as metal 61,430 11,359,000 Zinc in alloys other than brass 13,300 Tin as metal 7,950 Tin in alloys 23,000, 35,165,400 Antimony as metal 1 3,794,000 Antimony in alloys : 10,839 Aluminum as metal 17,700 24,816,000 Aluminum in alloys 26,300 Nickel as metal 191 1,518,000 Nickel in non-ferrous alloys 2,109 Total l 882,600 $243,570,700

Jan 1, 1928

By George A. Roberts, Arthur H. Grobe

H. H. Hausner (Sylvania Electric Products Inc., Bayside, N. Y.)—I tested the 18-8 stainless steel powder described by Grobe and Roberts and the results were excellent. The powder was compacted and sintered in purified hydrogen to a very low density (approximately 20 pct and more porosity). Where the other powders show very little ductility when sintered to such a low density, the described stainless steel was surprisingly high in ductility. I would appreciate it if the authors could give us some data on a similar powder but without silicon and also data on 430 stainless steel powder. H. S. Kalish (Sylvania Electric Products lnc., Bay-side, N. Y.)—I should like to verify the excellent results obtained by Grobe and Roberts with their pre-alloyed stainless steel powder. It seems to me, however, that their data are conservative and that even better densities and higher tensile strength can be obtained with these powders by the selection of proper particle size fractions. The accompanying data were obtained by sintering compacts pressed from the powder made by Vanadium-Alloys Steel Co. to 0.8 in. in diam about % in. high in a cylindrical double action die without the use of lubricant. The compacts were sintered for 1 hr at 2370°F in hydrogen purified by passing it through a Deoxo unit (palladium catalyst) and a Lectrodryer. Even the density obtained using the as-received (—100 mesh) compacted at 40 tsi was quite high as was the hardness. This indicates that by increasing the sintering temperature slightly above 2350°F the coining and subsequent secondary sintering operation can be avoided. With the — 325 mesh fraction, however, very much higher density can be obtained and a high hardness. I have no tensile data to present, but I feel that it is not too optimistic to expect. that unusually high tensile strengths and good ductility can be obtained in this sintered material on the basis of the density and hardness data. The sintered stainless steel made by the above-described methods came out of the furnace very bright and clean. The purified hydrogen atmosphere is important in sintering stainless steel to reduce the oxide present in the powder. The result of such a sintering is good densification and good ductility of the sintered product. G. A. Roberts (authors' reply)—We are greatly indebted to Messrs. Hausner and Kalish for their discussions of our paper. Their encouraging remarks are greatly appreciated and their confirmatory data will do much to add to the value of the paper. At the present time it is impossible to provide complete data on a similar stainless steel powder without silicon, but we do know that, in general, the properties are slightly inferior. Data on such a powder and on other stainless steel types are to be published in the near future.

Jan 1, 1952

By Joseph Moses Botbol

In passing the judgments essential to his trade, the geologist may be assisted by two new methods. These will enable him to (1) arrange the minerals of a selected group of base metal mining districts in the order of their typicalities and (2) compute the degree of mineralogic association between the model so derived and a district external to the model. It must be remembered, of course, that the methods discussed in this article are no more powerful than the structure of the model used and the data available. The geologist who employs these techniques must still exercise his expertise

Jan 1, 1970

By W. H. Bassett

In considering the effects of reducing gases on hot solid copper the following conclusions have been reached. (1) Depth of deoxidation of copper heated in reducing gas is greater the smaller the amount of cuprous oxide originally present in the copper, the range studied being from 0.015 to 0.136 per cent. oxygen. It is suggested that the reason for this difference in depth of deoxidation is that, when the copper is low in cuprous oxide, the reducing gas is diluted less by the gas that is formed in the reaction than when the copper is high in cuprous oxide; and the greater the concentration of the reducing gas the deeper the deoxidation. (2) The rate of deoxidation is much mire rapid at the beginning of exposure than at the end, a condition especially noticeable at temperatures around 900° C.; that is, deoxidation is retarded as the depth penetrated by the reducing gas increases. (3) Within the accuracy of the experiments arsenic in copper up to 0.5 per cent. has no tendency to increase or decrease the action of a reducing gas on the cuprous oxide present in the copper. IN 1912 pieces of 0.365-in. hard copper rod 1/2 in. long were heated in a porcelain tube in an electric furnace, while illuminating gas was passed through. An approximate analysis of this gas is: FIG. 1.-EFFECT OF TIME AND TEMPERATURE ON DEOXIDATION RATE OF 0.365-IN. COPPER BY ILLUMINATING GAS; COPPER PLUS SILVER, 99.983 PER CENT. Hydrogen 38 per cent., carbon monoxide 30 per cent., illuminants 13 per cent., methane 10 per cent., ethane 3 per cent., carbon dioxide 3 per cent., nitrogen 2 per cent., oxygen 0.4 per cent. After heating for various lengths of time at various temperatures, samples were quenched

Jan 1, 1926

By JAS. F. McCARTHY

THE present Hecla Co. is a Washington corporation; the Hecla Co. of Idaho was the old company. The older corporation owned two claims, the Hecla and the Katie May, and was incorporated for 500,000 shares of one dollar par value. The principal shareholders and officials of the older company were among the early mining men of the camp. Among the active officials were John A. Finch and A. B. Campbell. Among the directors and share- holders were Patrick Clark, J. R. Smith, Frank Upman, F. J, Kipp, Chas. Kipp, B. A. Kipp and Carl Landsee. F. J. Kipp and Carl Landsee are now directors of the Company. All of the others mentioned have died, but the surviving members of their families retain their ownership in the Company's shareholders. B. A. ,Kipp, who recently died, was the largest shareholder at the time of incorporation and Patrick Clark was the second largest shareholder. B. A. Kipp is a brother 'of F. J. Kipp, director of the Company.

Jan 1, 1924

By Malcolm T. Hepworth

RECENT interest in thermoelectric devices has been directed toward studies of the properties of thermoelectric materials of semiconducting solid compounds with little attention given to ionic and semiconducting liquids such as aqueous solutions, fused salts, and mattes. One type of thermoelectric system is the thermocell: a nonisothermal galvanic cell with two identical electrodes at different temperatures connected by an electrolyte bridge. An electromotive force, v, is generated which is a function of the electrode reactions and the properties of the electrolyte according to the Eastman' equation: where S* is the entropy change of the system arising from the electrode reactions and by heat transferred by ion migration and by thermal conduction. The quantity nF is the product of equivalents passed and Faraday's constant. A value of S* of 23.06 cal per "C is equivalent to 1 mv-Faraday per "C. The symbol, a, is used for dV/dT in analog to the See-beck coefficient of solid-state thermoelements. de Bethune2 has calculated the temperature coefficients of the electromotive force of a large number of nonisothermal aqueous cells from measurements on the nonisothermal temperature coefficients of the standard hydrogen electrode, combined with data on the isothermal temperature coefficients of half-cells tabulated in the literature. Values of these coefficients (a) in de Bethune's compilation ranged up to 3 mv per C. In particular he reported a value of +2.059 mv per "C at 25'C for the cell: Fe (aqueous, unit activity) (aqueous, unit activity) written for the hot-electrode reaction. The positive sign indicates that the hot electrode is positive (an "n-type thermocell"). In analog to a solid-state p-n system, it would be possible to couple two thermocells together to form a system in which the figure of merit could be calculated by adding the temperature coefficients according to the relationship described by offee:' where a is the Seebeck coefficient in volts per "C, p is the specific resistivity in ohm-cm, and K is the thermal conductivity in watts per cm "C. Even though ionic systems have rather high electrical resistivities compared with semiconducting and metallic systems, it was felt that a preliminary study of one ionic system should be made to establish some basis for evaluating the possibility of a p-n thermocell for energy conversion. Accordingly the Fe", Fe"' system was studied as a possible component for a p-n system. A glass system was constructed consisting of two vertical water-jacketed tubes connected by a horizontal tube, Fig. 1. Platinum-black electrodes 1 cm by 1 cm in dimension were inserted in each vertical tube with thermometers to register the electrode-compartment temperatures. The temperature of the electrode compartments was controlled by circulating water from thermostatted baths around the electrode compartments. The electromotive force of the cell was then read by a potentiometer for zero current as a function of the temperature of the hotter electrode. Current output of the cell for varying external loads was also measured. The cell resistance was measured by means of a bridge circuit with 10,000 cps signal and oscilloscope. Resistance measurements were converted to specific resistivity by calibrating the cell with a solution of known conductivity.

Jan 1, 1965

By D. W. Fuerstenau

In 1940 Schuhmann1 showed that the size distribution of a comminuted material can be expressed by the following empirical relationship: y = 100 (|f [i] where y is the cumulative percentage of material finer than size x, k is a size modulus, and a is a distribution modulus which is constant for a given material and machine. During the past few years, considerable emphasis has been given to the investigation of the extent of size reduction resulting from the expenditure of mechanical energy in crushing and grinding. Recently Schuhmann' presented a derivation of the energy-size reduction relationship by postulating that comminution in a device such as a ball mill can be considered to be the summation of many single comminution events, each of which yields a size distribution of particles following the Schuhmann size distribution equation. By grinding

Jan 1, 1961

By L. F. Pease, J. H. Brophy

A phase diagram for the Ta-Zr system is presented. The system is of the minimum-melting point type with the 0-zirconium phase decomposing monotectoidally at 785°C and 95.5 at. pct Zr. The minimum solidus temperature is 1875°C and the temperature of the top of the monotectoid loop is 1775°C. Techniques employed included X-ray diffraction and fluorescmce, electron microprobe analyses, diffusion couples, metallography, and melting-point measurements. Errors due to interstitial solutes and in melting observations are particularly common in this system, and their occurrence is discussed. SEVERAL versions of the Ta-Zr phase diagram have been reported in the literature.lm7 Williams et al.' report a diagram of the minimum-melting point type with a monotectoid reaction at 800°C and 12 wt pct Ta. The minimum in the solidus occurs at 1820°C and 25 wt pct Ta, while the top of the monotectoid gap is located at 1780°C and 80 wt pct Ta. The experimental techniques employed were metallography, electrical resistance variation with temperature, dilatometry, X-ray diffraction, and direct observation of melting by the technique of Pirani and ~lterthum.' Experience in the Nb-Zr phase diagram has shown that small changes in the interstitial content can cause large shifts in the positions of the phase boundaries. Small amounts of inter -stitials can cause similar changes in the Ta-Zr system and may be responsible for the wide variations in the phase diagrams previously reported.'-' The authors15 have found that alloys containing 0.75 wt pct 0 and 1.0 wt pct Ni with tantalum contents from 19 to 85 at. pct often contain a lamellar or cellular precipitate after annealing above 1400°C. This precipitate is very similar to that reported by pollack,12 Ralls," and Donlevy17 for the Ni-Zr system. In the present investigation, a wider variety of experimental techniques and improved alloy purity were applied to the resolution of errors in diagrams for this system as they now appear in the literature. New results have been obtained in the areas of alloy homogeneity and purity. Errors in the common techniques of direct melting observation in binary alloys have been demonstrated. In the commercially important high-tantalum region, the more accurate metallographic method of solidus determination has been employed. EXPERIMENTAL PROCEDURE Nominal analyses of the materials employed are given in Table I. The zirconium was low hafnium reactor grade iodide crystal bar, and the tantalum was in the form of high-purity sheet. Powders were impossible to use because of gas content. Alloys were melted on a water-cooled copper hearth, with a thoriated tungsten-tipped nonconsumable electrode in 2/3 atm of Zr "gettered" argon. Alloys were

Jan 1, 1963