Search Documents

By Jasper L. Stuckey

PYROPHYLLITE, first identified as soapstone,' later as agalmatolite,2 and finally as pyrophyl-lite, has been known to occur in North Carolina for more than 130 years and has been produced intermittently in commercial amounts for the past 100 years. Pyrophyllite mining, however, has become a major industry in North Carolina only during the past 25 years. North Carolina and California are the chief producing states. Current annual production averages 125,000 tons, of which slightly more than 90 pct comes from North Carolina. Distribution and Geologic Setting: All known pyrophyllite deposits in North Carolina are associated with rocks of the Carolina Slate Belt,' which is composed of a vast series of metamorphosed volcanic and sedimentary materials, occurring as two zones extending in a northeast-southwest direction across the state. The larger of these zones, lying in the central Piedmont region, varies from 8 to 50 miles wide. The smaller zone lies along the eastern edge of the Piedmont region and is partly covered by coastal plain sediments. The rocks in both zones consist of a great volcanic-sedimentary series, composed of air-laid and water-laid tuffs and breccias, lava flows, and slates. On the basis of composition, they may be classed into three groups: 1) tuffs, breccias, and lava flows of acid or rhyolitic composition; 2) tuffs, breccias, and lava flows of a basic or andesitic composition; and 3) water-laid slates composed of fine grained materials derived chiefly from the acid tuffs and breccias and

Jan 1, 1959

By Mehmet Guney

At the Armatcuk mine in Turkey, various modifications of sublevel methods have been tried during the last decade in an effort to eliminate gob fires, dangers from roof falls, and surface subsidence, and also to increase extraction efficiency. From the experience thus gained, it was decided that the most likely system to give maximum benefits, considering the existing geological conditions and coa1-seam characteristics, was hydraulic stowing. This paper examines trends in the working techniques of hydraulic stowing and discusses the favorable results and technical problems that the method produced at Armutcuk. The Armutcuk mine, a subsidiary of Eregli Coal Mines (EKI), produces 1300 tons of run-of-mine coal daily from thick (about 10-90 ft) and highly dipping (about 50-90°) coal seams. The coal is highly volatile with good coking properties that make it highly suitable for industrial use. Most of this coal is used in the iron and steel industry at Eregli on the Black Sea coast. Complete recovery of the coal is of vital importance to industrial development and progress. Initial coal extraction was carried out by means of a sublevel mining system modified to accommodate local geological conditions and coal seam characteristics. This method is similar to that employed in metalliferous mines. Several problems arose from the application of the method, one of them being the prevalence of gob fires which caused periodic shutdowns in some sections. To achieve maximum coal extraction with minimum dilution, to eliminate gob fires and surface subsidence, and to reduce fatal accident rates, a decision was taken to change from this method to a hydraulic stowing system. The pres- ence of large deposits of conglomerate and sandstone on the surface contributed to the decision to employ this new method. Although hydraulic stowing practices have been carried out in America and Germany, Upper Silesia may, so far as coal is concerned, be considered the birthplace of the method. Here the process was adapted to thick coal seams on a large scale to reduce dangers from gob fires and damage from surface subsidence. Today, the mining system is not only widely used in the coal mines of France, the Saar, India and Poland, but has also been successfully applied to the iron ore and potassium salt mines in Russia and Germany. LOCATION AND HISTORY The Kandilli-Armutcuk coal field, the most western outcrop of the North Anatolian coal basin, extends for five miles along the Black Sea coast (Fig. 1). The Armutcuk Mine is situated on the southern boundary of the coal field about 40 miles from Zonguldak and about 12 miles from Eregli. The history of coal mining in the North Anatolian coal basin goes back more than a century. Mining commenced on a small scale in the Kandilli-Armutcuk coal field in the late 1880's, and from this time until nationalization in 1940 the mines were operated by private Turkish and foreign interests. In 1940, Eregli Coal Mines was established to takeover the management of these enterprises. The Armutcuk Mine was developed for the first time in the mid-1940's. Since then it has been in continuous production and it now produces an annual 440,000-ton run-of-mine output from which 320.000 tons of salable coal is obtained. MINE GEOLOGY The carboniferous inlier of the Kandilli-Armutcuk coal field crops out over an area about three miles long and one mile wide. The major part of the inlier consists of the Namurian formation with only a relatively small area of Westfalian-A visible on the surface (Fig. 2). The Namurian formation, which has no exploitable coal seams in the Armutcuk Mine, consists mostly of arkose sandstones and black shales often having

Jan 1, 1969

By A. Alonso, J. Daubenspeck

In the nickel extraction process at Nicaro, Cuba, dried and ground nickel bearing laterites are reduced at 1300-1400F in multiple-hearth furnaces. Nickel is leached from the reduced ore by aeration in an aqueous solution of ammonium carbonate. Nickel carbonate is precipitated from the liquor and calcined to yield nickel oxide. The following are the more important modifications of the Nicaro process since plant rehabilitation and expansion. Ten percent increase in tonnage was achieved without decreasing the fineness of the ore by minor mechanical modifications of the grinding plant. Another five percent increase in tonnage was attained by intentionally overloading the ore prepration and leaching circuits in an effort to control cobalt extraction. Modifications at the sintering plant allowed it to handle the entire output of the expanded plant. A fifty percent increase in leach liquor cooling facilities alone provided an increase in nickel production of five percent. Stronger fresh leach liquor for increased nickel washing efficiency was obtained through improved distribution of water to the ammonia absorption towers. Advantage was taken of the reduced calcine's capability to precipitate cobalt, and modifications in the leach liquor circulation provided controlled cobalt solubility with minimum harm to nickel extraction. Several process changes at the drying plant brought about a ten percent reduction in the fuel oil consumption at this pint. Controlled air addition to the reduction furnaces' upper hearths burned formerly wasted combustibles thereby reducing oil consumption by twenty percent. The nickel extraction process successfully emplayed on the extensive but lowgrade lateritic ores of Eastern Cuba at the U. S. Government owned Nicaro plant, has been previously described in various publications. The large mine and plant operated by the Nickel Processing Corporation, located on the northeastern shore of Oriente Province, have been recently expanded to a yearly capacity of about 50 million pounds of nickel. Essentially, the operation involves open pit mining of a limonite-serpentine ore mixture containing 1.3 to 1.4 percent nickel and 34 to 38 percent iron. The comparatively lumpy, wet (25 to 30 percent moisture) ore is first dried and ground prior to chemical treatment, to which the entire 7,000 tons per day feed must be subjected. In the initial chemical action the dried and ground ore is reduced with carbon manoxide and hydrogen at 1300-1400° in multiple-hearth furnaces. The resulting metallic nickel is selectively leached from the reduced calcine by aeration in an

Jan 1, 1961

By Charles E. Locke

DEPRESSION in all lines of the mineral industry except gold, which began in 1930 and continued, even worse, through 1931, had its effect on ore concentration. Construction was limited to the completion of plants already begun. Every possible economy was adopted. Changes and improvements involving expense were postponed. Research was largely abandoned. Operations became highly efficient and costs were cut down, although this did not necessarily mean a lower cost per ton because of the greatly reduced capacity at which mills were run. Lower metal prices caused the operators to seek the optimum ratio of concentration and grade of concentrates looking toward maximum economic recovery; that is, net profit. In the crushing field no marked changes occurred. The Symons cone crusher for intermediate work is in use almost everywhere. Its manufacturers claim that 900 machines have been installed in 21 countries, replacing two previous steps of crushing and yielding a product sufficiently fine to form a satisfactory feed for rod mills and ball mills. A new Telsmith crusher has appeared which has curved jaws something like the Symons cone and consequently the same advantage as the latter.

Jan 1, 1932

By Charles R. Keyes

the leaching of near-by rocks, had had no other result than to bring out from obscurity three certain features of practical lmport, all the labor of that controversy would have been well expended. These three points are : (1) a clear distinction between the vadose and the profound zones; (2) a determination of the manner in which the latter may be invaded by conditions of the former; and (3) an establishment of the general truth of the lateral-secretion theory when vadose conditions prevail, and of the. ascension-theory under profound conditions. In the practical consideration. of ore-deposits these generalizations are fundamental. Their wider application must be productive of great industrial advantages. Of first importance in the broader scientific survey of ore-genesis is the recognition of a sharp distinction between vadose and profound conditions. To many who listened to Professor Posepny's remarkable paper, read at the Chicago session of the Institute during the Columbian Exposition in 1893, this seemed, as Dr. S. F. Emmons has already observed, its most valuable and suggestive feature. Notwithstanding Posepny's implications to the contrary, and his vigorous berating of Sandberger's views, the immediate and lasting .effect of the . argument was really to strengthen greatly Sandberger's position. For it completely and sharply separated the lateral-secretionists from the ascensionists, raising the sphere of the former bodily above the line of permanent water-level and at the same time confining .the sphere of the latter to regions below that horizon. A little later, Professor Van Rise showed in some detail how meteoric waters may deeply invade the profound zone and carry vadose conditions into it. The zonal limitations of two great and apparently opposed agencies being thus definitely fixed, it is found that neither of the theories based thereon is susceptible of general application. If the generalizations of the lateral-secretionist be propounded solely for vadose conditions, we are able to agree with all of his more-important contentions; while there is general acquiescence in the views of the ascensionist if their application be restricted to the profound zone. Of the ore-bodies of the world that are mined to-day, the majority are essentially vadose in origin, and probably originated

Jul 1, 1910

By J. R. Dunn

Planning quarry operations and control of the quality of rock materials at Hudson Cement Co. at East Kingston, N. Y., are special problems because of multiple uses for the stone and the great structural complexity of the rocks. Problems have been largely solved by detailed geologic work. These geologic studies have paid dividends in long and short range planning, in assessment of reserves, in vastly reduced cost of chemical analyses, and in reduced drilling costs. Limestones of the Hudson Valley outcrop along the Hudson River from Albany to Kingston. Old established cement companies are located just south of Catskill and just east and southeast of Hudson, N. Y. The new Atlantic Cement plant is being constructed at Ravena. Hudson Cement located at East Kingston, is a newcomer and is closest to the New York metropolitan area (Plate I).

Jan 11, 1961

By G. F. Butterworth

The metallographic structures most frequently encountered in rifle barrels, and which are illustrated by the accompanying photomicrographs, fall naturally into two groups, distinguished by the method used to, produce in the stock a physical condition having the requisite properties. The fist group consists of "rolled" barrels; that is, barrels subjected to hot working by rolling in or near the critical range. In the second group, the stock, which is smaller in diameter than the first, is upset to form the butt end and is then heat treated by giving it a quench and a draw. These barrels will be referred to as " heat-treated " barrels. The structure of the rolled barrels resembles closely that of the same steel after annealing. There is the same network of excess ferrite outlining the grain boundaries, but the grains themselves are composed of sorbite rather than pearlite. The grain size is closely related to the rolling temperature. The critical-point curves of this grade of steel, which is approximately 0.50 to 0.60 per cent. of carbon and 1.00 to 1.30 per cent, of manganese, show a single very pronounced point between 1300" and 1350" F. (704" and 732" C.). Barrels rolled within this temperature range give an exceedingly fine grain, shown in Fig. 1. In fact, the grains may be so fine that, at a low magnification, they may be confused with the heat-treated structure shown in Fig. 6. A magnification of 500 diameters, however, will always resolve a rolled barrel into the characteristic structure shown in Fig. 2. As the temperature is increased, the grains are found to be larger. If, on the other hand, the rolling temperature is below the critical range, the structure previous to rolling will not be obliterated, the only effect of rolling being to elongate the coarse sorbite grains in the direction of rolling, Fig. 3. This distortion is greatest at the muzzle. Heat-treated barrels are quenched in oil from above the critical range, which should give a martensitic structure, Fig. 4, but the presence of some troostite in the martensite is frequently noted when the quench has not been sufficiently drastic, Fig. 5. The structure brought about by the subsequent draw is not so striking, though quite as typical. It is sorbitic or sorbito-pearlitic, and under a low magnification appears almost homogeneous, as in the case of fine grains of pepper and salt well mixed together, Fig. 6. This structure is substantially the same for all

Jan 1, 1920

By P. O. Metz, E. L. Wiehe, J. S. Foster

BASED on their analyses of growth kinetics, ibbs' and Harris et al.' have recently proposed that the rate of subcritical graphitization of steel is controlled by the rate of diffusion of carbon in ferrite. illert has concluded that this is the rate controlling growth mechanism when the growing graphite particles are relatively large. Harris et al.' also propose that the matrix surrounding a growing graphite particle is plastically deformed to make room for the growing particle. If this plastic deformation does occur, then preferred recrystallization may be observed around the larger particles. If diffusion of carbon in ferrite is rate controlling, then a graphite particle growing in a matrix of, say, tempered martensite or pearlite, should be surrounded by a carbide depleted zone. Thus, the simple metallographic experiments reported here are sufficient to determine whether or not diffusion of carbon in ferrite is the dominant mechanism for the growth of graphite in steel. The present investigation considers graphitization in five alloys. The compositions are given in Table I. Graphitization was carried out at three temperatures: 900°K (627"C), 950°K (677"C), and 990°K ('717°C). Samples were reacted in both the martensitic and the pearlitic initial conditions. In the hypoeutectoid steels, Sets 7 and 8, .and in the hypereutectoid Fe-C binary, Set 6, graphitization was very limited after 1000 hr at temperature. In these samples graphite particles observed were less than 10 p in diam. In the hypereutectoid commercial steels, Sets 1 and 3, large graphite particles (100 p) did not appear until after 250 hr at temperature. The limited number of graphite particles observed and the range of sizes obtained prohibited measurement of growth rates in this investigation. However, in all samples showing graphitization, neithe a carbide depleted zone nor recrystallization was observed. illert's model predicts that diffusion of carbon in ferrite should become dominant for graphite particles larger than about 300 p in diam. The largest graphite particle observed in this investigation was approximately 450 p in diam. No evidence of carbide depletion was noted. Fig. 1 shows a typical graphite particle. This nodule is from an initially pearlitic sample from Set 3 after

Jan 1, 1970

By H. H. Moss

OXYACETYLENE .cutting has experienced rapid development in the last few years and greater advances and expansion and broader application may be expected in the immediate future. Marked changes in cutting practice may be expected as a result of the advances in metallurgical science that have produced special alloy steels with properties requiring different cutting techniques than for ordinary low-carbon steels. Much current attention is being directed to those problems of modified cutting practices. Cutting has thus ceased to be merely a shaping problem. It is rapidly coming to have a predominantly metallurgical aspect. The problem is no longer how to cut a given shape, but how to cut a given steel. The answer

Jan 1, 1936

By P. B. Leavenworth

Development in the Upper Texas Gulf Coast during 1945 resulted in the discovery of 23 new fields; one Miocene, eight Frio, three Cockfield-Yegua and eleven along the Wilcox trend. The Wilcox trend appears to he the most active at this time. Producing depths of the new Wilcox discoveries range from 2050 to 10,050 ft. Drilling along the Frio trend has been, for the greater part, projected to the deeper downdip sands. Eighteen of the new discoveries are classified as oil or condensate and five are gas discoveries.

Jan 1, 1946

By G. M. Schwartz

THERE has been considerable controversy regarding the structure and mineral constituents produced when iron ore is sintered. This investigation was undertaken in order to establish the fundamental reactions that take place in the sintering process by determining the nature of the resulting minerals. The writer's immediate interest in the subject arose mainly from the request of E. W. Davis for information based on a microscopic study of sinter submitted by him in May, 1926. In the author's preliminary work, samples of iron-ore sinter were secured from the Minnesota School of Mines Experiment Station and from commercial plants. These were polished by the usual methods for polishing opaque ores. In order to study these surfaces satisfactorily, it is necessary to magnify them rather highly, a range from 100 to 1000 dia. being used. For the higher magnifications oil-immersion lenses and an intense source of light are necessary. After the preliminary study had shown the problems involved, a series of small samples were sintered under carefully controlled conditions and with analyzed materials. Variations in the relative amounts of ore, coal and water were made in order to study the effect of each constituent. The attempt has been to arrive at a clearer understanding of the sintering process and the reactions involved without reference to any preconceived notion as to sinter. It is clear that the study of polished surfaces has yielded results not possible with thin sections alone. The thin sections made in this work were found unsatisfactory at magnification greater than 75, whereas magnifications of 1000 were easily studied with reflected light on carefully polished surfaces. A rather complete statement of observed facts is made so that the reader may form his own conclusions. The writer's interpretations are suggested.

Jan 1, 1929

By B. E. Field

COBALT is a silvery white metal with a slight bluish cast, strongly resembling nickel in its appearance and properties, notably its resistance to corrosion, although its alloys with other metals differ quite decidedly in their properties from those of nickel. The name cobalt was derived from the German "Kobold" meaning goblin and this came to be applied to the cobalt minerals which, although they resembled ores, did not readily yield metal when smelted by the primitive processes available in the Middle Ages. Cobalt minerals were used as pigments by potters and glass workers before the Christian era. Cobalt blue glass was found in the tombs of the Egyptians and in the ruins of Troy, and many colors used by the ancient Greeks and Romans contained cobalt. The ancients were entirely unaware that the colors they used were caused by cobalt and the metal itself was only isolated about the middle of the eighteenth century by Brandt although the preparation of cobalt compounds had been carried on in a small way ever since the opening of the silver-cobalt deposits at Schneeberg, Germany, in 1470. The metal is fairly hard, with a density when pure of 8.81 in the cast state and 8.92 after working. The com¬mercial grade of cobalt has a density of about 8.75 in the cast state. The atomic weight is 58.97. The Brinell hardness of the pure metal is 124; that of the commercial grade varies from as low as 100 to as high as 138, depending upon the impurities present. Pure cobalt has a sharp melting point at 1478°C. The tensile strength of the pure metal in the cast condition is said to be higher than that of any other pure metal. Kalmus gives it as 34,400 lb. per sq. in. for cast unannealed metal; the effect of annealing at 850 to 900°C. is to raise the strength slightly. The yield point is close to the ultimate strength and the reduction in area and elongation are both low. Mechanical working raises the tensile strength of pure cobalt rapidly and in the form of wire it will be over 100,000 lb. per sq. in. The presence of small quantities of carbon in the commercial metal raises the tensile strength to as high as 61,000 lb. per sq. in., the reduction in area and elongation being raised at the same time to approximately 20 per cent.

Jan 1, 1933

By Harold Price

ONE year ago, that is in January, 1923, there had not been constructed a single oil-storage tank of 55,000-bbl. or more capacity with a completely electric welded roof and bottom. Today, there are at least fifty 80,000-bbl. storage tanks completed, or nearing completion, on which both the roofs and the bottoms are electric welded. It is the purpose of this paper to describe, in a general way, the construction of these FIG. 1.-ELECTRIC-WELDED SEAMS AND RIVETS OF BOTTOM IN 55,000-BBL. TANK AT EL DORADO, KANS., SHOWING ALSO PATCH PLATE WELDED TO BOTTOM. welded roofs and bottoms, and to give their advantages over riveted construction. All of the following data and conclusions were obtained from observations made during the welding of tanks by the Welding Engineering Co. at Texas City, Tex., and Tonkawa and Burbank, Okla. As far as can be determined, the first electric welding on large tankage was completed in May, 1922. At that time the Empire Companies of Bartlesville, Okla., discovered a badly leaking bottom in a 55,000-bbl. tank at El Dorado, Kans. They had considered concreting this bottom, but because of the much smaller cost, decided to try electric welding; so a- contract was given the Welding Engineering Co. of Bartlesville, Okla. In this instance, no new sheets were added, the bottom being repaired by electric welding of all seams and rivets, Fig. 1. In some places where the original rivets were missing, the holes were filled by welding; patch plates were also added at certain badly worn spots. This tank has since been in service over a year and half, but no other

Jan 6, 1924

By George S. Rice

GROUND movement and subsidence is an important matter from several points of view and it is regrettable that more papers have not been written on this subject in the past year. Damage may be done to surface buildings or to the higher workings of a mine, and a study of the subject gives valuable in- formation on hanging-wall or roof control. The latter objective is strikingly shown in a recent paper presented by Jack Spaulding on Oct. 21, 1937, before the Institution of Mining and Metallurgy, of Great Britain, entitled "Theory and Practice of Ground Control in the Kolar Gold Field, India." All may not agree with some of his theories that were deduced from studies of the many violent rock bursts at depths of 5000 to 7000 ft., but the data obtained are of great value. His theories of symmetrical ring stresses and symmetrical domes which are pictured as perfect are rather hard to understand as such uniformity is un- likely in view of the irregularities in the formation due to folds and fractures of various kinds. All will agree in principle with this idea of domal effects, which have been observed in many countries, but they are generally irregular.

Jan 1, 1938

By C. H. Mathewson

MY treatment of the subject of "Metals of the Future" is imaginative rather than statistical or scientific, because reliable information concerning useful concentrations in the form of ore deposits of by far the majority of the elements does not exist and the chemical, physical, and mechanical properties of the unfamiliar metals are recorded only in fragmentary and uncertain form or not at all.

Jan 1, 1944

By J. R. Vilelia

IN accordance with the custom of this society, we are gathered here, as we have every year since 1924, to honor the memory of the eminent American metallurgist and teacher, Professor Henry Marion Howe. Unlike many of the distinguished metallurgists who have preceded me as a Howe lecturer, I cannot bring to you reminiscences of his personality, for it was not my privilege to be associated with Professor Howe, or to be directly one of his students. Yet, Professor Howe and Professor Albert Sauveur, through the medium of their books, were my first teachers of metallography, as they have been of almost all American metallurgists of my generation. As a teacher, and for many years the acknowledged leader of American metallurgists, he exercised a profound influence in the growth of our science and was held in honor by the men of science of his time. I can speak no words of technical appreciation that will add luster to his fame, for by his prophetic vision, his teachings, and his researches he stands among the immortals in the memory of all metallurgists. In 1926, the third Howe Memorial Lecture was presented by Professor William Campbell' of Columbia University, who entitled it "Twenty-Five Years of Metallography." He took as a starting date for his chronology the turn of the century, which coincided with his arrival from England to work in association with Howe at the Columbia School of Mines. In that informative lecture Professor Campbell enumerated the important advances in metallography achieved during the first quarter of the century, and, it now appears, may have established the custom of reviewing such progress every twenty-five years. The scope of Professor Campbell's lecture was as broad as his metallurgical knowledge, for it embraced a wide portion of the field of metallography, both ferrous and nonferrous. Twenty-five years later, the Howe Memorial Lecture Committee saw fit to assign to me the honor of writing a lecture that would commemorate the work of Henry Marion Howe and would at the same time constitute the 25th anniversary of the lecture by Professor Campbell. The Committee suggested that this lecture might properly be called "Twenty-Five More Years of Metallography," a suggestion that I have adopted. I must confess, however, that I have not followed the precedent established by Campbell and have narrowed the scope of this lecture to an appraisal of those achievements which in my opinion have contributed most to the progress of microscopical metallography during the past twenty-five years. Progress in Metallography The metallographic methods most widely used today, with the exception of the electron microscope, were firmly established more than twenty-five years ago. In general, our specimens were prepared for microscopic examination in those days in much the same manner as they are today. It is true that new details of technique have been introduced from time to time, and that superior equipment is available today, but on the whole, these improvements have been in the nature of refinements, often a matter of personal preference, and none can be considered essential to the attainment of the ultimate goal of the art and science of metallography, which is to reveal the structure of metallic specimens with unequivocal clarity so that they may be interpreted correctly. Mechanical metallographic polishing, which was the only method available in 1926, is still universally practiced and still consists of abrading the metallic specimen with a series of abrasives of increasing fineness until a specular surface is attained. We have now the alternative method of electropolishing, but it is not widely used because, except in a few special cases, its results are inferior to those of competent mechanical polishing. Likewise, most of the etching reagents preferred today were in common use more than twenty-five years ago and were applied in the same manner as they are today. Valuable improvements have been made in the optical and mechanical performance of metallurgical microscopes, but there was no dearth in those days of excellent instruments equipped with achromatic and apochromatic objectives capable of yielding micrographs comparable in quality with the best that we can make today. In fact, it would be a difficult task for any metallographer today to make optical micrographs at magnifications in excess of 3000 diameters that would surpass those made by Lucas more than twenty-five years ago. One of these is shown in Fig. 1. Yet, it is unquestionable that on the whole, the micrographs appearing in the metallurgical literature today are vastly superior to those

Jan 1, 1952

By George M. Fowler

DURING 1937 the subject of mining geology was probably given more attention and more mining geologists were usefully employed than at any previous time. Of the many contributing factors the most important were: (1) a higher degree of prosperity in many countries, (2) a. better understanding of geologic phenomena, and (3) the apparently diminishing reserves of several important minerals. Mining companies have come to look upon geology with a growing appreciation of its aid in the more effective exploration and exploitation of mineral deposits. Most of the larger and more active companies have one or more geologists permanently attached to their staffs and some have well organized and efficiently managed geological departments. Even the smaller companies, who feel they cannot afford to employ a geologist on a permanent basis, are seeking the advice of competent men in this field with increasing frequency. One of the most significant trends has been the growing tendency to base exploratory work on more thorough geologic studies instead of empirical "hunches,"on which so much off the work in the past has relied. Likewise, mining companies are apparently more willing to expend larger sums on the basis of geologic possibilities in a district.

Jan 1, 1938

By Charles Hart

In this paper it is the author's intention to show the extent and character of foreign ores now known to be available; these deposits may be in active production or held in reserve until economic conditions may make them active. He hopes to show the relation existing between these ores and the American supply, and which of the former are now producing or will in turn come into production when our better ores have been exhausted. This phase of this discussion must of necessity include some data as to the present rate of consumption and a study of the changes we may expect here and abroad in the general steel trade and its sources of supply in raw materials. It is obvious that the occurrence of coal, ore and limestone in relation to one another and the proximity of a market are the elements in control of this feature of the problem. If the foregoing situation is favorable, all the other questions may be solved, for it is clear that with proper basic conditions finance, labor and operations will fall in line. We present a short outline of the present methods of carrying on the foreign iron ore trade, believing that it is of general interest in comparison with our own highly specialized methods, and that with the exhaustion of our better ores we will be compelled to seek a part of our supply abroad. A partial list of iron ores, with incomplete analyses (Table I), is added, to give a better understanding of the general situation and explain to some extent the reason for things being as they are in the iron and steel trade of the world and to help in bringing this paper to an informing conclusion. The question of the world supply of iron ores has been a subject for study on the part of geologists and engineers for many years, and found its best results in the Eleventh International Geological Congress, appropriately held at Stockholm, Sweden, in 1910. The proceedings are published in two volumes and are undoubtedly the best records available on this subject at the date of publication. It should be borne in mind, however, that much has happened in the 20 years since these figures were assembled. There is just as much known ore at present as at that time, minus the quantity consumed, plus newly discovered reserves. The World War had great effect upon this situation; during that time explorations were greatly reduced and the settlements after the

Jan 1, 1929

By J. F. Breedis

The stabilization of austenite in Fe-Ni alloys against martensitic transformation after reversion has been attributed' to the lattice imperfections remaining from previous transformation. More recently, however, such stabilization has been associatedzy3 with compositional changes which occur in martensite during slow heating. Dislocation arrangements in deformed austenitic stainless steels strongly influence transformation to martensite on quenching.4 Therefore, it is of interest to observe the transformation behavior of stainless steel after reversion, especially since previous studies have been confined to Fe-Ni alloys. The transformation-product morphology also differs in the two iron-alloy systems;6 plate martensite forms in the latter while stainless steel transforms to lath-type martensite. Samples of Fe-16 wt pct Cr-12 wt pct Ni (maximum C + N = 0.005 wt pct, 0 = 0.02 wt pct), prepared by vacuum melting and casting from high-purity components, were annealed at 900°C for 24 hr, after cold rolling to produce a 40-p grain diameter. The M, temperature of this alloy is -80°C and samples are fully austenitic after annealing. The amount of martensite present after quenching, annealing, and requenching was determined magnetically, to within 0.01 wt pct, using a vibrating specimen magnetometer. Nearly 14 pct of martensite forms during the initial quench in 1 min at -196°C. Two-min and 2-hr anneals were done in air and in evacuated quartz capsules, respectively. All specimens were electro-polished before making the magnetic measurements.

Jan 1, 1967

By Rossiter W. Raymond

(Chattanooga Meeting, October, INS.) THE formal outline of Mr. Hague's life and work is embraced in the following statement, chiefly based upon data furnished by him, at my request, shortly before his death. At that time the probability that I would survive to record his death was apparently small; but I urged upon him the duty of providing, whether for me or for my successor as Secretary of the Institute, trustworthy material for the notice which somebody would some day have to write-and which might otherwise be incomplete or incorrect. Mr. Hague, with characteristic promptness and freedom from affectation, did what I asked of him; and I am therefore . able to present an authoritative sketch-concerning the details of which I shall add my own comments, and some particulars obtained from others of his personal friends. James Duncan Hague was born Feb..24, 1836, at Boston, Mass., where his father, Rev. William Hague, D.D., an eminent clergyman, then resided. After a preliminary, education in private. schools, be studied in 1854 at the, Lawrence Scientific School of Harvard University; in 1855 and 1856 at the University of Göttingen, Hanover; and from 1856 to 1858 at the Royal Mining Academy of Freiberg, Saxony. In 1859-1861 he was attached as chemist to a South Sea exploring expedition, sent by W. H. Webb, of New York, to examine Jarvis, Baker, and other islands for phosphate-deposits. After the outbreak of the Civil War, he entered the U. S. Navy, serving for a year as Judge Advocate to the fleet stationed at Port Royal, S. C. In 1863 he became Superintendent of the Albany and Boston copper-mine, in the Lake Superior region, where he was also connected with the earliest development of the Calumet and Hecla property. In 1867 he became the First Assistant Geologist in Clarence King's famous Exploration of

Feb 1, 1909