Search Documents

By Eric Yoshimitsu Sako

One of the main difficulties in the operation of trough and runners at Arcelor Mittal Tubarão (AMT) Blast-furnace no.02 is the reduced amount of time available for repair procedures. The consequence is that the castable installation must often be performed during hot conditions and the installed castable could easily detach from the base material during the early stage of operation, exposing the previously oxidized base material to molten iron and corrosive slag attack. When events like this happen, emergency repairs must be executed, resulting in increased refractory unit consumption and an unplanned shutdown of unit operation. Considering these targets, Nippon Crucible Co. and Saint-Gobain HPR Brazil have developed a high-performance Al2O3-SiC-C composition based on an entirely novel anti-oxidation technology. Oxidizing reactions could be attenuated by adding an oxidant inhibitor and a water reducing agent. As a result, the open porosity was significantly reduced, resulting in an improvement of campaign life in terms of pig iron throughput when compared with the regular castable. An analysis of this life improvement showed successful results for the material after 250 days of campaign. The main reason for such successful results was that the deterioration caused by the oxidation was significantly less and that this change made on the high cohesive structure of the base material was maintained for a long time. The attained results allowed Arcelor Mittal Tubarão to achieve longer trough campaigns, and avoid any unplanned stoppages with zero breakdown risks.

Oct 30, 2017

By Jan Lampke

Increasingly pelletizing discs are used for the recycling of dust and sludge. The applied pellet feed is highly variable, for example in terms of chemical composition, grain size distribution and raw density. These raw materials related factors lead to a destabilized pelletizing process, which initially must be homogenized through special mixtures, as well as the use of binders or additives. There are many possibilities to reach stringent restriction of material related target factors. On the one hand it is helpful to be flexible by changing the process parameters of the pelletizing disc. On the other hand, it is necessary to use a material-binder-formulation, which leads to a highly stable pelletizing process. The paper deals with an example of the use of agglomerating device, pelletizing disc, to prepare different dusts and sludges for material recycling. These dusts und sludges are mostly generated in metallurgical processes, e.g. sinterplant, blast furnace and steelworks.

Aug 16, 2017

By Flávio Beneduce Neto

As trincas a quente ou de solidificação em peças micro-fundidas em superligas a base de níquel podem ser um item importante no índice de perdas em componentes específicos. O aparecimento desse defeito está ligado fundamentalmente à quantidade de líquido interdentrítico nos últimos estágios da solidificação e, principalmente, ligado à composição química desse líquido. Há duas ligas amplamente utilizadas na produção de rotores para turbo-compressores ou turbinas para a geração de energia: o Inconel 713C e o Inconel 713LC. A diferença entre estas duas ligas é essencialmente o teor de carbono. Curiosamente, a liga LC tem uma maior tendência ao aparecimento de trincas de solidificação. O presente trabalho procura identificar as diferenças de comportamento na solidificação dessas duas ligas através da termodinâmica computacional e ligar essas diferenças no aparecimento das trincas. Os resultados indicaram que os teores de Zr e Nb do líquido remanescente da solidificação são muito superiores na liga LC causados pelo atraso na precipitação dos carbonetos tipo MC nessa região que deve ser a fase que aumenta a resistência mecânica da área. O correto balanceamento da composição química da liga em relação aos elementos citados permitiu que o índice de perdas por trincas de solidificação caísse para níveis próximos a zero.

Aug 8, 2018

By Shanti Arangala

Several improvements were made to the single strand rod mill at Laverton to increase production, reduce maintenance and improve several aspects of product quality. With changes to the water cooling line and control system, cobbles could be significantly reduced, more consistent properties obtained and yield improved. An upgrade of the laying head enabled vibrations to be reduced and thus allowed for higher speeds on small sizes. With potential for dramatically increased pipe life, a new pipe support and laying pipe system provided for improved laying pattern on small sizes and thus more uniform cooling on the conveyor and better coil package. This paper discusses details of these equipment and control system upgrades and the resulting benefits that have been realized from the project.

Aug 16, 2017

By Daniel Antonio Kapper Fabricio

A avaliação das propriedades de mecânica da fratura dos materiais é uma necessidade crescente, sobretudo no setor de óleo e gás. Esse cenário exige a garantia da qualidade na execução de ensaios de tenacidade à fratura. Esse trabalho tem como objetivo realizar uma comparação intralaboratorial para o ensaio de tenacidade à fratura KIC variando o executante do ensaio, visando atender ao requisito de garantia da qualidade da norma NBR ISO/IEC 17025. Os resultados foram comparados através de análise de variância. As diferenças entre os operadores não foram significativas frente ao erro residual a um nível de confiança de 95%, sendo tal resultado considerado satisfatório.

Aug 16, 2017

By Horacio Destaillat

Desde hace aproximadamente 15 años se encontró por experiencia empírica que se puede “neutralizar” el efecto del plomo sobre la maleabilidad en caliente de cobre proveniente de la refinación térmica de chatarras mediante control de la composición química. Este hallazgo ha resultado de aplicación industrial. Si bien el contenido porcentual de plomo se reduce por refinación convencional y con cierta facilidad hasta 0,02 – 0,03 %, este valor es elevado [1] para laminar en caliente. Bajar el nivel de plomo hasta los valores exigibles por normas, requiere procedimientos especiales y costosos. La técnica cuyo mecanismo aquí se investiga, consiste en ajustar el contenido de plomo y estaño dentro de ciertas proporciones, ya que el balance de estos elementos, permite proceder sin problemas de fisuraciones a la colada y laminación en línea del cobre. Con el control de la composición química del sistema se logra que el plomo y el estaño se adhieran [2] sobre las partículas de eutéctico Cu-Cu2O. Esta disposición micro estructural en borde de grano explica la acción favorable del estaño en la maleabilidad. El procedimiento que aquí se describe no es aplicable a cualquier caso pues no funciona en materiales con contenido elevado de oxígeno (“Tough pitch”) ni en cobres desoxidados. Solamente lo hace en formas de baja sección que hayan sufrido enfriamiento rápido.

Aug 7, 2018

By Rodrigo Ribeiro de Andrade, Túlio César Nogueira, Ed Juarez Mendes Taiss, Nilton José Lucinda de Oliveira

The objective of this study was to determine the effects of an eventual slab central macro-segregation in microalloyed steels with low Mn content (0.80%) and high Nb content (0.08 to 0.10%) on the kinetics of recrystallization of austenite during its rolling, on its critical temperatures, that is, of non-recrystallization (Tnr), start Ar3 and finish Ar1 of ferrite transformation and its response to a simulated industrial thermomechanical processing. The determination of the austenite recrystallization kinetics was made through isothermal double compression tests using a dilatometer, while the critical temperatures were determined through hot torsion tests in a Gleeble® 3800. It was found that austenite recrystallization kinetics, Ar3 and Ar1 temperatures did not present significant changes for the samples extracted both at ¼ of the thickness and at the core of the plate, indicating that, as expected, the central segregation in this type of steel was not intense to the point of affecting this phenomenon. The Tnr values determined for the samples extracted in the core of the plate were, on average, 30°C lower than those obtained from specimens extracted at ¼ thickness, which suggests that a significant portion of the carbonitrides present in the core of the slab are eutectic and coarse, not having completely dissolved during the reheating of the specimens. This occurred despite the fact that the austenitization temperature adopted in this treatment theoretically leads to the total dissolution of Nb, as seems to have occurred in the case of specimens extracted at ¼ of thickness, where carbonitrides have a finer size.

Oct 1, 2019

By Guilherme Guidugli

The hot blast stoves are a regenerative heat exchange system, accounting for 10 to 20% of the total energy requirement in an integrated steel plant, responsible for the supply of about one-third of the blast furnace heat input and responsible for a constant flow of hot air to the blast furnace, according to the required production. Because of their important role in the hot metal production, a stable operation and an appropriate combustion control is necessary. This paper aims to present the results of an investigation and modifications performed as an operating multi-furnace plant, as well as the parameters considered to ensure thermal equilibrium, improving in the stoves heating cycle.

Aug 16, 2017

By Helênio Resende Silva Júnior

Arcelor Mittal Asturias coking plant at Gijon works, Spain, is undergoing a complete modernization of the whole coke making complex. In this context, Gijon has to be considered a brownfield project, where Paul Wurth has been awarded with the engineering, supply of key equipment as well as erection and commissioning supervision services for the rebuild of two coke oven batteries the modernization of the adjacent by-product and relevant waste water treatment plants. Main objective of this paper is to present the technological improvements introduced by Paul Wurth in the rebuild of a modern plant focusing on fulfilling all the recent environmental regulations.

Oct 30, 2017

By L. Martins Demuner, D. Burzic, V. Cunha Aranda, F. L. Lourenço, G. Romeu Trindade dos Santos, F. Ramstorfer

For many years, Dynamic Soft Reduction has been regarded as a proper method in improving internal quality of slabs. Even though processes models improved significantly over the past years, the efficiency of Soft Reduction was always limited by the discretization error, which inherently exists if segment rollers cannot be positioned individually. The recently developed SRD segment type allows for an individual roller positioning within the mushy zone by avoiding any discretization deviation from the optimal gap. This paper provides a detailed technological overview of the SRD segments as well as operational results at their very first implementation at Ternium Brazil.

Oct 1, 2019

By Fernando Ruiz Díaz

En aplicaciones a elevadas temperaturas como por ejemplo en cámaras de combustión y toberas de vehículos aeroespaciales se requiere el uso de aleaciones que permitan una elevada extracción de calor y buenas propiedades mecánicas. En este trabajo se realiza un análisis comparativo de las aleaciones Cu-Cr-Zr y Cu-Ag-Zr. Las mismas fueron sometidas a ensayos de resistividad eléctrica entre 25ºC y 700ºC y de tracción a 150ºC, 450ºC y 700ºC. Los resultados de los ensayos de resistividad eléctrica fueron convertidos a conductividad térmica mediante la relación de Wiedemann- Franz. A través de este análisis se observa que la aleación con mejor conductividad térmica es la de Cu-Ag-Zr presentando además un cambio de fase que no es observado en la aleación Cu-Cr-Zr. Respecto al ensayo de tracción la aleación Cu-Cr-Zr presenta mayores valores de resistencia a la tracción y tensión de fluencia a las temperaturas estudiadas.

Aug 16, 2017

By Henrique Silva Furtado

Light meter is an ArcelorMittal innovation that uses off-gas light intensity to predict bath carbon, which is akin to the visual cues that the operators employ to finish a blow. Light meter enables the prediction of end point that is independent of any operator’s judgment. The results have been in general consistent with the actual carbon content at BOF end point at Tubarão. Besides some outliers that occurred due to strange intensity curves, the system implemented in Tubarão BOF 3 reported a carbon prediction error statistic that is very similar to dissolved oxygen–carbon end point statistics. Preliminary trials using light meter without any filter improved carbon hit ratio significantly.

Jul 30, 2018

By Diego Pacheco Wermuth

Micrometric surgical components typically have high geometric complexity and stringent regulatory specifications. These components need to have excellent mechanical properties and a high demand of products. Besides these factors, it is necessary to maintain a low manufacturing cost, performing essential research on new manufacturing technologies. Metal Injection Molding (MIM) is a process that has been explored , providing an interesting alternative for making medical devices. The research in the production of microcomponents obtained for MIM is gaining momentum and prominence, due to low cost and high productivity of this process. This paper is a study and development of feedstocks with AISI 316L alloy , which is known for its biocompatibility. Four feedstocks with 61%vol. of metal powder were analyzed by capillary rheometry and DSC/TGA.

Aug 16, 2017

By Juliano Braz Possatti, Arnaldo Carneiro Salles, Cleudson dos Santos Rego, Leandro de Lucas Mendes

The increase in customer demand for steels with higher surface requirements, associated with the need to increase ArcelorMittal Tubarão's HSM productivity, it was necessary the development of controls and actions to reduce scale losses within the scenario of high productivity. This article describes the path followed by the hot strip mill team in order to reduce the occurrence and severity of scales.

Oct 10, 2019

By Daniel Hajduk

Efficiency of back up rolls depends mostly on two parameters – length of campaign and dressing amount after the campaign. The longer the campaign (in terms of rolled tones) is, the higher the dressing amount. To solve this task properly it is necessary to know the distribution of accumulated damage in the working layer of the roll caused by previous campaigns and by loads (separating force and bending) during present campaign respecting changing conditions of material properties (hardness) through radius of the roll. To find an optimum dressing amount an algorithm has been developed and specialized computer program will be presented, that takes real measured loads during the backup roll campaign, calculates fatigue damage in the roll and suggests relevant dressing amount. This can help to prolong service life of rolls, minimize the risk of spalls and reach maximum efficiency in terms of rolled tones/km per roll.

Jul 30, 2018

By Ivan César Lopes Diniz, César Romero Afonso Goulart Júnior

Mandrels are tools applied to manufacturing seamless tubes. In VSB plants (Vallourec Soluções Tubulares do Brasil), it is used in two mills. Mandrel and PQF Mills. This is an expensive tool due its alloy (hot work tool steel – AISI H13) and lengh (between 12 meters and 22,5 meters). An opportunity to apply mandrels from PQF in Mandrel Mill has been identified. However, mechanical properties of PQF mandrels must be improved. This work presents the heat treatment process of Quenching and Tempering developed internally at VSB to improve PQF mandrel properties aiming to achieve Mandrel Mill requirements. Hardness and metallography tests were performed before and after some steps of the heat treatment to characterize and validate the process.

Oct 5, 2019

By Robert Horwood, Richard Harvey

The copper stave was a development of the Blast Furnace cooling system intended to utilise the high heat transfer properties of copper within a fully covered shell cooling solution. They were originally conceived as being able to provide a permanent cooling lining for use primarily in the higher heat zones of the Blast Furnace. Despite a large number of campaign successes around the world the everlasting concept has not proven universal, with some plants having suffered issues in two particular areas: stave bending (leading to water leaks at back of the stave) and stave wear (erosion on the hot face). Primetals Technologies have in the past been approached to provide assistance to a number of Blast Furnace operators who were experiencing operational issues with the copper stave furnace cooling systems of others. Through knowledge gained resolving these issues, and with the positive experiences of their own copper stave designs, Primetals Technologies have worked towards developing a new concept in copper stave design capable of providing a more robust solution to cope with the greater productivities of modern ironmaking. This paper will provide an outline to the concepts that have driven the design of this new technology.

Oct 1, 2019

By Peter Grawenhof

In steel mills universal joint shafts, slipper spindles and gear spindles are used to overcome the design- and process- related offset between the axis of the motors and the work rolls. At the roll side the available space for the couplings is limited by the minimum work roll diameter. This leads to extremely high loaded components of the universal couplings especially at the roll side joints. Furthermore modern steel mills continuously strive to roll larger plates and materials with increased strength. This requires drive solutions with even higher torque capacity. For these applications conventional design joints are not sufficient anymore. Even alternative solutions such as hybrid- or offset- designs fall short. Therefore the companies Voith and BUMA Engineering developed together the new GearLink drive concept in close cooperation with the Voestalpine Grobblech GmbH. A completely new combination of universal joints and gear couplings offers an up to now unique solution enabling the use of 1,35- times bigger joint with a 2,5- times higher torque capacity and a 20- times longer lifetime. The GearLink system was first time successfully taken into operation at Voestalpine Grobblech in December 2013 and is up to now working without issue.

Aug 16, 2017

By Paulo Rodrigues dos Santos Junior, Luciano Passos de Jesus, Vagno Dordenoni Beltrame, Vinicius Antonio Ramos Pin

Faced with an increasingly demanding and selective market, a thorough analysis of each step of the processes is required in order to achieve high levels of performance. In addition to a major factor of importance in the rolling process, due to its high price, the rolls represent one of the main items in the cost of hot coils production. Using the 6 sigma methodology, there were opportunities for improvement in the grinding process, fatigue analysis, improvement in NDT in rolls, as well as means to guarantee operational stability, which allowed the reduction of roll’s consumption and consequently the cost of production.

Oct 11, 2019

By Túlio Magno Fuzessy de Melo, Luciano Santos Marques, Vicente Tadeu Lopes Buono

The influence of the coiling temperature after hot strip rolling on the microstructure and on the tensile and hole expansion properties of a 800 MPa multiphase steel was investigated. For the temperatures between 150°C and 600°C the microstructure consisted of a ferritic matrix with a dispersion of fine martensite-austenite (MA) and regions of degenerated upper bainite. In all cases the ferrite presented a heterogeneous mixture of polygonal, quasi-polygonal and acicular grains. The yield and tensile strengths showed a tendency of decreasing with the increasing coiling temperature, probably because of the larger fraction of MA particles at lower temperatures and higher fraction of quasi-polygonal ferrite at higher temperatures. The elongation was not significantly affected by the variation of coiling temperature. The average hole expansion ratio showed a maximum of 80% for the material coiled at 400°C and fell below 50% only for the coiling temperature of 150°C, probably due to the larger hardness difference between the ferrite matrix and the MA particles.

Oct 1, 2019