Search Documents

By Gustavo Borges Tiboni

The erosive wear caused by the impact of solid particles against a surface is a tribological phenomenon present in many segments of the industry, such as transportation, aerospace, mining, power generation, among others. The most usual method to set the wear rate is by measuring the mass loss of the material. In order to apply one technique with potential to determine the rate of erosion wear, this study developed a dedicated equipment and conducted preliminary erosion tests monitored by non-destructive testing known as acoustic emission technique (AE). This can be defined as a technique able to detect mechanical waves generated by the release of elastic energy accumulated in the material. Erosion tests were performed in order to evaluate the ability of equipment to collect data from AE and to correlate these data with the wear of the samples. Samples of low carbon steel eroded by the impact of angular aluminum oxide particles suspended in air at three different velocities: 45, 57 and 67 m/s. The impact angle between the particles and the sample was set at 30 degrees and the test temperature at approximately 20°C. The wear rate has changed with the velocity in accordance with the kinetic energy of the particles and the AE parameter RMS showed sensitivity to the variation of particle impact velocity and to the wear of the sample eroded. The rate of AE signals collected over time correlated with the flow of particles striking the sample, and with the parameters of energy, rise time and duration of the signal.

Jul 31, 2018

By Carlos Alberto Mourão, Robson Martins, Letícia Madureira Moreira, Hélio Braz Loss, Joilson Moreira Ferreira da Silva, Edilson Simões Cavalieri, Mauricio Ferreira Coelho

O conversor AOD-L é de uso exclusivo para a produção de aços inoxidáveis na Aperam South America. Entre janeiro a julho de 2018, o consumo de FeSi estava acima do orçado, acarretando em perda de gestão para a Aciaria. O aço inoxidável AISI 304 representa 50% da produção da Aciaria na rota duplex (sem uso do VOD), portanto, esse projeto teve como objetivo a redução do consumo da liga de FeSi no AOD-L para o aço AISI 304. Essa redução foi possível através da utilização da metodologia Lean Six Sigma na qual a causa raiz foi identificada e as ações implementadas o que permitiu uma maior estabilidade operacional, além de aumentar a competitividade da Aperam South America frente aos demais produtores mundiais.

Oct 1, 2019

By Euzébio Bernabé Zanelato

A produção de peças cerâmicas pela indústria da cerâmica vermelha é composta por diferentes processos, dentre eles, se destaca o processo de queima. O processo de queima é um dos principais responsáveis pelas propriedades finais da peça cerâmica, tais como: resistência mecânica e porosidade. Por ser um processo gradativo, onde a temperatura é elevada até determinado grau, o ambiente proporcionado pelo forno é fundamental para a homogeneidade de queima das peças, no entanto, existem diferentes formas para a realização dessa queima. O objetivo deste projeto é comparar e avaliar o processo de queima por forno Hoffman e forno Caieira. Para caracterização da argila foram realizados os ensaios de granulometria, densidade real dos grãos, limites de Atterberg e análise química. Para acompanhamento da temperatura do forno foi utilizado um termopar digital e verificada a temperatura durante o processo de queima. Para avaliação do melhor processo de queima foram realizados os ensaios de variação linear e absorção de água das peças cerâmicas. Os resultados indicaram que as peças cerâmicas queimadas pelo forno Hoffman apresentam propriedades superiores aos do forno Caieira.

Oct 30, 2017

By Antônio Aldenor Pinheiro Neto, Matheus de Lima Vieira

In mid-2015 the steel industry faced a strong crisis due to the weak performance of the Brazilian economy and the persistent entry of Chinese steel into Brazilian territory. This situation demanded that Brazilian steelmakers seek to develop products to meet new export markets. within the volume of exports possible are the rebars, where its applications are in the construction industry. One of the largest importers is Peru which has a large percentage of this export volume. This market demands as a priority requirement the surface quality of blue condition (low oxidation index) and mechanical properties normative.in order to meet the items required by the customer at a competitive cost, a vanadium microalloyed steel was applied to the hot rolling process without heat treatment after the last rolling pass. Where the great challenge was to achieve a high level of stretching without compromising the minimum limits of tensile strength. Assuming that the steel used is the correct one interventions were made on rolling parameters such as set-point temperature, residence time of pieces in the furnace, linear mass and rolling speed. All the changes made were based on statistical tools and practical tests. Finally, with the execution of actions generated from the statistical analyzes and tests it was possible to reduce process losses by 96%.

Oct 1, 2019

By Bianca Proença

Fotocatalisadores de nióbio foram obtidos por anodização a 15 V, utilizando uma solução de K2HPO4 10% p/p em glicerol anidro como eletrólito por 15 minutos. As amostras foram caracterizadas por difração de raios-X para avaliação da estrutura cristalina obtida. A fotodegradação do glicerol (utilizado como agente de sacrifício) foi avaliada pela técnica de cromatografia líquida de alta eficiência.

Aug 16, 2017

By Maycon Athayde

Samarco produces high quality iron ore pellets processed in straight grate furnaces. This process is essential in order to obtain adequate mechanical strength to the pellet transportation and operation in the reduction reactors. All mechanical properties of the agglomerates are obtained during the stage of firing where the slag and sintering bond happens, thus it is a decisive step to improve the pellet quality. Therefore, the velocity distribution of gas flow within this zone must have homogeneous and even velocity distribution. Hence, it was developed a mathematical CFD model to characterize the gas flow in the burning zone, applying the equations of conservation of momentum, mass and energy and an uneven flow distribution was identified and the gas velocity analyzed and validated through experimental data. On the other hand, on the present paper, an improved firing zone burner were developed and industrially implemented in a way to mitigate the uneven flow pattern detected aided by CFD. Different burner designs, based on CFD analysis, were experimented in order to succeed on the aggressive condition. The combustion was investigated and burner efficiency evaluated and compared with the simulation purposed.

Aug 2, 2018

By Luiz Peixoto, Andrea Falcon

There are a few ways to impact the capacity of a reciprocating compressor, by altering suction and discharge pressure and recirculation. By reducing the pressure drop in the section before the compressor it is possible to provide a higher suction pressure and subsequently achieve a higher compressor flow rate. The increase in the suction pressure while maintaining the discharge pressure reduced the demanded compressor Head. When considering oxygen compressors it is necessary to cautiously evaluate the safety norms and parameters due to the risk of explosions and fires due to high oxygen velocity.

Oct 3, 2019

By Alexandre Rizek Schultz

Silat, Siderúrgica Latino-americana, selected Russula as the main engineering contractor for their 700,000 tpy Greenfield steel plant dedicated to long and flat steel production. The project is currently under construction in the district Guararu in Caucaia in the metropolitan region of Fortaleza. The project will be developed in two phases. First phase: 600,000 tons per year rebar mill and 60,000 tpy steel mesh line; Second phase: 700,000 tpy melt shop (90 ton/hr EAF and 4 strand continuous caster for billets up to 180 mm x 180 mm).

Aug 16, 2017

By Dalton Martins Neto, Sandro Valério Maia Larrubia, Alexandre Patricio Vieira da Silveira

A TERNIUM Brasil, Rio de Janeiro, tem em sua operação dois Altos-Fornos idênticos. Ambos iniciaram operação em 2010, Alto-Forno 01 em 13/07/2010 e Alto-Forno 02 em 06/12/2010. Em Dezembro de 2016 e Janeiro de 2017 ocorreu alguns eventos de rompimento de conjunto de sopro por temperatura alta ocasionando paradas emergências nos Altos-Fornos, perdas de produção e instabilidade operacional. Diante deste problema, a antecipação de possíveis falhas no conjunto de sopro por temperatura alta foi fundamental para garantir operação estável dos altos-fornos. Analisar o processo, verificar procedimentos, pesquisar e aplicar novos materiais para adequar as condições operacionais é essencial para evitar o rompimento de conjunto de sopro por temperatura alta e elevar vida útil dos mesmos.

Oct 1, 2019

By Márcio Lobato Genelhu

Este trabalho tem o objetivo de apresentar o modelo de recuperação refratária a quente dos regeneradores dos altos-fornos, através da técnica de solda cerâmica, visando o aumento da vida útil e evitando a parada prematura para a manutenção destes equipamentos. A aplicação da solda cerâmica prolongou a vida útil dos regeneradores.

Aug 8, 2018

By Leandro Rigo Ramos, Marcelo Lucas Pereira Machado, Lumena Gloria de Souza Nunes, Mariana Valinhos Barcelos

The aim of this work was to study the influence of temperature on the grain refining process from severe plastic deformations through the simulation of Accumulative Roll Bonding (ARB) by torsion tests. The assays were performed to simulate the ARB at three different temperatures of 550 ° C, 625 ° C and 700 ° C with 5 torsion cycles with equivalent strain of 0.8 per cycle at a rate of 0.1−1 , totalizing an accumulated deformation of 4.0. Grain refining was obtained with an average size of 2μm, 5μm and 6μm for the temperatures of 550 ° C, 625 ° C and 700 ° C respectively. There was a rise in Vickers hardness by 68%, from 119HV in the annealed sample to 175HV in the deformed sample at 550 ° C. In the deformations at 625 ° C and 700 ° C the value of 130HV E and 150HV respectively was obtained. Based on the obtained results, it can be stated that the severe plastic deformations in microliged steel, carried out at temperatures lower than the end of the austenite-ferrite transformation, produce refined grains of the order of 2μm and, consequently, increase the mechanical strength of the material.

Oct 1, 2019

By Tiago Seixas Bittencourt

Technological developments, associated with the constant worry about the environmental impacts arising from industrial activity, it has driven the development of technologies and practices for efficient fumes and particulates capture arising from the manufacturing processes of steel in steel plants in general. Currently, the electric steelshops in operation with Electric Arc Furnaces (EAF), seek parameterize/design dedusting systems able to retain most of the particulates generated during melting and refining of steel in FEA through configurations of equipment, technologies and parameters operation in order to equalize the antagonistic relationship between effective fumes capture and energy balance of the EAF. The present work gets as a fundamental premise to evaluate critically the possible different settings of the usual dust removal systems, as well as their respective classical parameterizations. The work main purpose is to establish a general rule evaluation technique for dedusting system considering the different modes of operation of an Electric Arc Furnace.

Jul 30, 2018

By Daniel Antonio Kapper Fabricio

Laboratórios realizam o ensaio para determinação da tenacidade à fratura KIC, mas para verificar a validade dos resultados, é importante que se estime a incerteza de medição do ensaio. O Guia para Expressão da Incerteza de Medição (GUM) apresenta um método reconhecido internacionalmente para se estimar a incerteza de ensaios quantitativos. O presente trabalho apresenta o desdobramento das etapas do GUM para o ensaio de KIC e a aplicação da planilha e do procedimento elaborados em um ensaio. Ao final, é realizada a análise crítica de quais fontes mais contribuíram para a incerteza de medição do ensaio executado.

Aug 8, 2018

By Steven G. Jansto

Carbon content and continuous casting parameters affecting solidification behavior, such as super heat, mold level fluctuation, heat transfer, fine grain chill zone depth and other process solidification parameters directly influence the surface and internal quality of the steel strand. The carbon content, resultant fine grain chill zone depth, the equiaxed-columnar transition zone and the strain energy are the primary drivers that govern hot ductility behavior. These factors influence the propensity for crack formation during the unbending section in the continuous casting process. Elements such as microalloys exhibit secondary or tertiary root causes for crack formation and are not the primary crack formation root cause. This solidification research identifies that the traditional hot ductility as measured via the percent reduction in area (%RA) at elevated temperature grossly overstates the minimum ductility required to assure crack-free casting of microalloyed steels. The strain at the ultimate tensile strength exhibits a very high correlation coefficient with strain energy while an extremely low correlation coefficient is exhibited with %RA.

Oct 30, 2017

By Daniel Antonio Kapper Fabricio

Laboratórios de ensaios têm buscado implementar Sistemas de Gestão da Qualidade baseados na norma ABNT NBR ISO/IEC 17025 e procurado a acreditação de seus ensaios. A norma ASTM E517 estabelece um método de ensaio para a determinação do índice de anisotropia plástica de metais laminados, um importante parâmetro em processos de conformação mecânica por estampagem. Atualmente nenhum laboratório é acreditado pelo Inmetro na realização desse ensaio. Assim, o Laboratório de Metalurgia Física (LAMEF) da UFRGS optou por aumentar seu escopo de acreditação para abranger esse ensaio. O objetivo do trabalho é apresentar as adequações gerenciais e técnicas ao Sistema da Qualidade existente para a extensão de escopo, assim como as não conformidades encontradas e os pontos fortes para obtenção da acreditação junto ao Inmetro.

Aug 7, 2018

By Detlef Ehlert

Flexibility in terms of producing high sophisticated products with an exceptional wide range of properties and dimensions requires physical based process models for the generation of optimal set points. Therefore SMS applies since many years an integrated PSC® (pass schedule model), PCFC® (profile, contour and flatness model) and CSC (cooling section control) for the use in hot strip mills, CSP® plants and plate mills offering best possible product tolerances. Focus during the development of the model was made on the best possible physical description of the rolling process to minimize the need of complex adaptation algorithms. As an addition SMS has also developed a microstructure model to ensure the quality control with respect to mechanical properties and to save up the needs of taking samples. Beside of this the modular design of the Microstructure and Material Property Model (MPM) offers additional benefits to improve the accuracy of the other models, e. g. the recrystallization model in the finishing mill. Using the results of that model strain hardening or softening effects during rolling can be predicted and an optimum pass schedule can be calculated to avoid rolling stability problems related to phase transformation.

Aug 16, 2017

By Jerin Russell

This paper presents a new instrument for real-time detection of excessively coarse material in the overflow pipes of individual hydrocyclones using a non-invasive acoustic measurement technique. The hydrocyclone is an important device used in mineral processing beneficiation circuits for classification of mineral slurries by particle size. It separates a single input stream into two output streams; an underflow of coarse particles that undergo additional grinding for further size reduction, and an overflow stream of finer particles that typically goes directly into a flotation circuit for recovery of the desired mineral. However the hydrocyclone is a major piece of equipment in the beneficiation process that has no instrumentation for directly measuring its performance. The parameters currently measured – inlet pressure, feed flow rate, feed flow density – are common to the entire hydrocyclone cluster which typically has three to twelve hydrocyclones. Thus no information is available to detect individual hydrocyclones that are operating poorly. The system described in this paper detects the presence of unwanted excessively coarse material in the overflow stream of a hydrocyclone using sensors mounted to the exterior pipe surface. It provides real-time monitoring, trending and alarming of the coarse material level. This enables operators to identify poorly performing hydrocyclones, and enables corrective action to reduce or eliminate the coarse material discharge. Improving the classification efficiency of individual hydrocyclones will improve the overall classification efficiency of a hydrocyclone cluster. This leads to less variation in the particle size distribution and slurry density in the flotation feed, which will in turn improve overall mineral recovery. The reduction of unwanted coarse material in the flotation feed reduces the accumulation of that material in flotation cells. This can lead to equipment damage, and unplanned shutdowns due to events such as blocked dart valves.

Aug 16, 2017

By Jesús A. Carlos Cornelio

Since their discovery in 1991 Carbon nanotubes (CNTs) have attracted much interest due to their remarkable mechanical, thermal, electrical, chemical and optical properties. In connection with their mechanical properties, CNTs have been studied in various forms for tribological applications including their use as lubricant additives for oil and water. In this paper the tribological properties of CNTs (SWCNTs and MWCNTs) when used as lubricant additives are studied under rolling-sliding conditions in a twin-disc testing machine. The tests were performed using 5% of creepage and pressures of 0.8 GPa and 1.1 GPa. Used functionalized nanotubes were modified with carboxylic acid ultrasonically dispersed at different concentrations (0.01, 0.05%). The results indicated that the presence of carbon nanotubes leads to a decrease in both friction coefficient and wear rate for both systems studied (oil and water).

Jul 31, 2018

By Jorge Madias

La mayor parte de las máquinas de colada continua de palanquillas que utilizan buzas calibradas y lubricación con aceite se operan con alta velocidad de colada en secuencias largas, obteniendo alta productividad. Muchos de ellos todavía practican la inyección de aluminio en el molde, para desoxidar el acero líquido sin riesgo de obturación de las buzas. También es todavía usual la práctica de “pescar” la nata que se forma en el menisco. Las salpicaduras del chorro de cuchara contribuyen a la formación de chanchos en el repartidor, requiriendo el lanceo con oxígeno. Alternativamente, diversas plantas prefieren utilizar tubo de protección entre cuchara y repartidor y protección con gas inerte del chorro del repartidor al molde en todos los grados de acero colados con buza calibrada. Se hace una comparación entre ambas prácticas desde los puntos de vista de inversión, costo operativo, seguridad, productividad y calidad.

Jul 30, 2018

By Francisco de Paula Pinheiro

Estudo das fontes de variação do processo de vazamento contínuo de chapas de alumínio, através da aplicação de uma metodologia prática e rápida para solução de problema. Após identificação das variáveis críticas à qualidade, ações foram tomadas de modo a minimizar as perdas do processo, o que contribuiu para a redução nos custos de produção das chapas.

Aug 16, 2017