Search Documents

By Maurice C. Fuerstenau

The kinetics of leaching galena with ferric chloride and ferric nitrate have been examined as a function of ferric concentration, salt concentration, temperature and particle size. Diffusivity of ferric complex ions was also established as a function of ferric chloride concentration and temperature. In the presence of 3 M NaCl, leaching rate is controlled by product layer diffusion when ferric chloride is added as oxidant. With NaCl concentrations less than 3 mole/liter rate decreases with decreased NaCl concentration, and, thus, rate is apparently not controlled by product layer diffusion. It is suggested that rate is controlled by lead chloride solubility at the reaction interface under these conditions. When ferric nitrate is added as oxidant, leaching rate is limited by chemical reaction control. An electrochemical model is presented. Activation energies are 8.1 and 11.3 kcal/mol in the ferric chloride and ferric nitrate systems, respectively.

Jan 1, 1984

By G. C. Lammers

The object of this study was to determine the economic feasibility of hydraulically transporting Sandow (Tex.) lignite 100 miles and dewatering and thermally drying the transported lignite to a surface-dry condition. The most important factors involved in the feasibility of hydraulic transport, are the degradation incurred during transit, the length of the line, and the cost of alternative methods of shipment. In pipeline tests in which roughly 75 miles of hydraulic transport was simulated the percentage of minus-325-mesh solids increased from about 1 to 41 percent for both lignite and bituminous coal; in the micron sizes the coal fared considerably better than the lignite. Such degradation, even though it enhances flow through the pipe-line, severely aggravates the dewatering problem on lignite. Cost studies indicated that continuous vacuum filters offer the most economical means of dewatering minus-1/8-inch material. Surface moisture, if high, must be removed by relatively expensive thermal drying.

Jan 1, 1958

Tailings embankments can develop a high phreatic surface if the original design for the embankment does not include drainage facilities or if existing drainage facilities become ineffective. Subsequent raises can develop a seepage surface due to a high phreatic surface that can lead to stability problems. The U. S. Bureau of Mines amended contract J0100013 to initiate this study of horizontal drains in tailings embankments. This study developed a technique for determining the length of and spacing between parallel drains through the use of the finite element model UNSAT2. The analysis is based on the combined output of a vertical planar mesh and a horizontal planar mesh. The slot opening in the drain pipe and the length of the perforated section are determined from an analogy to water well design. The pipe diameter and gradient can be determined from Manning's equation. To the authors' knowledge, this is the first attempt at horizontal drain design using a finite element model. Additional research is recommended in this area.

Jan 1, 1982

By M. G. Wallis

This report presents the results of a study to develop a detailed mining method design based on longwall mining with sublevel caving. The method is applicable to low-dipping coal seams 20 or more feet thick such as are found in the western United States. The report covers (1) the development and description of the mining method, (2) evaluation of the engineering feasibility of the design, (3) estimates of productivity and recovery, and (4) an engineering cost analysis and economic feasibility evaluation of the mining method design.

Jan 1, 1977

By John P. Borovsky

A 3-year study was conducted to evaluate the problems and benefits of using vegetation to stabilize tailing from a potential Minnesota copper-nickel milling operation. The project consisted of three separate investigations: a waste characterization study, a greenhouse study and a field study. With few exceptions, the physical and chemical characteristics of the tai ling were found to lie within the range of properties of Minnesota soils. The tailing lacks organic matter; is deficient in nitrogen, phosphorus and potassium; and may contain elevated levels of soluble salts and heavy metals, particularly copper and nickel. Numerous grasses, forbs and woody plants will tolerate the tailing as a rooting medium. Peat incorporation and topsoil dressing provided few benefits to the revegetation process which were not provided by a fertilizer application. With fertilization, grass/legume production in the tailing was comparable to local agricultural yields. Concentration of heavy metals in grasses grown in the tailing were generally below suggested tolerance limits for plants and animal forage. Legumes tended to accumulate higher concentrations of copper and nickel, and metal uptake of most plants was positively correlated with rate of fertilization. Tailing drainage water contained elevated levels of heavy metals, and establishment of vegetation had little effect on the quantity and quality of tailing drainage water. However, topsoil dressing significantly increased drainage water volume when compared to unvegetated control plots. Copper-nickel tailing revegetation recommendations were developed.

Jan 1, 1983

By Donald B. Lindsay

A new concept was proposed for a personal warning device for use by miners who may be exposed to health hazards from inhalation of alpha-emitting radionuclides, especially radon-222 and its short-lived daughters. Two successive prototype models of the proposed instrument were designed, fabricated and tested. The Personal Alpha Alarm, in its final form, weighs less than 90 g (3 ounces), and can easily he mounted on a miner's safety cap. It is powered r, by electricity drawn from the cap-lamp battery, and consumes less than 100 n A at 4VDC. It is entirely passive and has no moving parts. Alpha-radiation originating in the air around it is detected by a 5 cm2-area semiconductor-type sensor that was developed especially for this purpose. The presence of alpharadiation in the air is communicated to the wearer by means of a small flashing light-a light-emitting diode-clipped to the brim of the safety cap. When the intensity of alpha-radiation exceeds a predetermined threshold, the flashing mode changes to a continuous illumination, thus providing an alarm signal to the wearer. Because the detector senses all alpha-emitters in the air, including 222Rn, it is not able to measure Working Levels accurately. For its intended purpose, however, which is to give a timely warning of excessive levels (several times the normal control level) of radon and/or radon daughters in an individual's air environment, the Personal Alpha Alarm is expected to be a useful instrument.

Jan 1, 1978

By Pedro Lilienfeld

This report presents a design and cost investigation for several alternative versions of a field-worthy mining machine-mounted respirable dust monitor. Three main design variations are considered: (a) light scattering sensing, (b) Beta-filter tape sensing, and (c) a combination of the two preceeding methods. Eventual instrument production coats as a function of design complexity are tabulated. Cost estimates for the development and field testing of field-worthy prototypes are also presented. A general discussion on the technical aspects of these design alternatives is included following a modular-hierarchical approach of progressive complexity. The technical background to this report has been provided by the experience and results derived from the work performed under U.S. Bureau of Mines Contracts Nos. H0166097 and H0377092.

Jan 1, 1980

By Eldon Keith Stanek

This annual report deals with four distinct tasks related to research on the safety and reliability of mine electrical power systems. Task one is to develop tests and the associated instrumentation to detect incipient faults on a mine or any low-voltage power system. Task two is a dual effort related to the digital prediction of electrical transients on mine power systems and laboratory testing of transient suppression devices. Task three is also a dual effort. This task consists of both theoretical and laboratory work to assess both the reliability and the fail-safe characteristics of several items of protective equipment used in mine power systems. Task four consists of an effort to use programmable calculators and/or computer terminals to check overcurrent protective device coordination.

Jan 1, 1976

By H. Miller

In recognition of the need for a portable low-profile hard rock crusher, the Bureau of Mines sponsored the development of such a unit capable of moving up as the face advances. By allowing primary ore reduction at or near the mine face, the advantages of conveyor haulage From the face as demonstrated in soft ore and coal mines, could be realized for hard rock Brines as well. This report presents the results of a development and testing program for such a portable low-profile crusher, designed by Eagle Crusher Company and called the M44. The unit has an extremely low vertical profile considering its size and capacity. The crushing jaws, which form the crushing lumber, are inclined, with the lower jaw mounted for eccentric movement relative to the stationary upper jaw. This provides efficient crushing while also forcing material through the crushing chamber. As a result, the inlet feeder can be disposed horizontally. To facilitate correct processing of different materials, the size of the discharge opening and the action of the movable crushing jaw are variable. The unit also incorporates a feeder hopper and discharge conveyor that provides for efficient ore handling through the machine. Tests demonstrated the M44 Crusher's high capacity, efficiency and reliability. During testing, it crushed over 120,000 tons of materials of up to 32,000 psi compressive strength at production rates in the 200-350 tons/hour range. The unit operated smoothly under simulated low-headroom conditions, and Proved readily transportable.

Jan 1, 1983

In attempting the predict coal cleat orientation in the subsurface for effective methane degasification of the coal beds in the Warrior coal field of Alabama, approximately 150 rock joint orientations and 45 coal cleat orientations were measured in each of 37 7 ½ minute quadrangles in Tuscaloosa, Walker, Jefferson, Fayette, Winston, Blount, and Bibb Counties. Data from these surface locations, and coal cleat data from eight underground mines was corrected for magnetic declination and titled beds rotated to the horizontal where necessary and plotted on rose diagrams for comparative analysis. Data collected on each joint and cleat consisted of attitude, quality, type, spacing, persistence, lithology, bedding thickness, surface texture, and filling. File data and published and unpublished reports from the State Survey and the State Mine Inspector's Office were re-viewed. Twenty-seven mining companies, most of which supplied information pertinant to the project were also contacted. The information obtained consisted of crop line information structure, and underground mine outlines, all of which were put on 7 ½ -minute topographic quadrangles. LANDSAT-1 imagery and Skylab photography were compared to dominant joint and cleat trends in the study area. Detailed results can be found in an open-file report entitled "Fracture Analyses in a Selected Area of the Warrior Coal Field, Alabama." A master's thesis entitled "The Relationship Between Surface Joints and Subsurface Structure in a Selected Area of the Warrior Coal Field" is being prepared to illustrate the relation-ship of the fracture system to the structure in the Warrior coal field. A proposal has been submitted for research on a project entitled "Rock Fracture Systems and Their Affects on the Extraction of Fossil Fuels in the Warrior Basin, Alabama"

Jan 1, 1976

By P. C. Hodges

WHILE there is very little romance connected with the operation of a stone quarry, yet to those who have participated in the growth and development of a business that has been a pioneer in its field and that FIG. 1.-LOCATION OF PROPERTY OF MARBLE CLIFF QUARRIES COMPANY. has been in continual operation two-thirds of a century there is bound to be a background of experience, which if properly capitalized, brings progress as well as satisfaction in its accomplishment.

Jan 1, 1936

By J. R. Long, A. H. Roberson, T. R. Graham, R. S. Dean

EXPERIMENTAL work on the properties of high-purity alloys of the copper-manganese-zinc system has necessarily required extensive metallographic work to determine the equilibrium conditions in this system. Previous work on these alloys is fragmentary and, unfortunately, based on alloys made with impure grades of manganese, thus introducing significant amounts of iron, silicon, aluminum and carbon. Since these elements are known to affect equilibrium conditions, it became desirable to re-examine these alloys made from the pure metals. The alpha solid solution field was of particular interest and, therefore, was chosen for the initial work, which was outlined to determine the composition limits of this field. PREVIOUS WORK Heusler1 conducted an extensive survey of the liquid-solid regions of this system and also made an estimate of the solid-phase boundaries at 340°C. The pertinent part of his diagram is given in Fig. I, but it is of limited usefulness, since it applied to a single temperature only and is based on impure alloys under admittedly nonequilibrium conditions. Bauer and Hansen,2 likewise working with impure alloys, have determined the phase boundaries for alphabeta brasses containing small amounts of manganese and indicate an increase in the extent of the alpha field with increasing manganese. This is not in accordance with Heusler or with data obtained on pure alloys.3 They also described a third constituent precipitating in the alpha plus beta field below 350° to 400°C. but did not identify this constituent. Guillet4 and Heike and Ledibur5 have also noted this precipitate Each of these investigators recognized that impurities present in the manganese could and did have an effect on the structure and properties of their alloys. Corson6 in particular pointed out the hardening effects of silicon, aluminum, and carbon in copper-manganese alloys and Heusler reported that his alloys containing more than 25 per cent manganese were extremely brittle. In all probability this brittleness was due to the impurities present. This early work, therefore, should be taken as a general guide for preliminary studies only, and high-purity alloys may be expected to produce different results. The work of the Bureau of Mines laboratories with electrolytic manganese has been briefly summarized by Dean7 but includes only a short section on this system. Later work3 outlined a limited portion of the alpha field in the neighborhood of 65 per cent copper, 10 per cent manganese, and 25 per cent zinc. The present work was under-

Jan 1, 1945

To allow the controlled yielding of mine walls in order to reduce rock-burst hazards and reduce maintenance caused by excessive squeezing forces. Approach Rock bolts that elongate and continue to sustain a load, have been fabricated and tested. This device is an adoption of a concept originally developed in South Africa for use where unusually adverse conditions may warrant the added cost. How It Works A coupling in the rock bolt allows controlled elongation if the load increases beyond the bolt's design strength. (The load can build up either slowly, as during heaving, or rapidly, as before a rock burst.) The elon¬gation of one or more rock bolts surrounding a mine opening, allows the rock to move from its original position to c new position in a controlled manner. This movement relieves the rock stresses, and the mine opening reaches a new state of equilibrium. The elongatible coupling of the rock bolt consists of a

Jan 1, 1977

By Harry Siewert

"The commissioning of the 4th concentrator (C4) at Freeport Indonesia in early 1998 increased total mill throughput from 130k to 230k tonnes per day. The C4 flowsheet consists of a single 38 ft diameter SAG mill, four 24 ft diameter ball mills followed by four banks of 4,500 ft3 WEMCO flotation cells.The design of the C4 rougher flotation circuit was based on the expectation that the copper and gold recoveries achieved with the 4500 ft3 flotation cells would be equivalent to or better than that achieved with the 3,000 ft3 flotation cells in the 3rd concentrator (C3) rougher circuit. This assumption was due to the fact that the C4 flotation feed size would be less than 15% +212 microns compared to the C3 rougher flotation feed size of less than 23% +212 microns. By mid 1998 it had become apparent that the C4 rougher flotation copper and gold recoveries were below those predicted.In order to determine the cause of the lower recoveries, stage by stage rougher flotation surveys were performed in all four concentrators. The results of the surveys showed that the C4 rougher flotation circuit had a lower recovery of +200 micron material than that achieved in the C 1, C2 and C3 concentrators. Through mineralogical analysis, it was determined that a majority of the copper contained in the +200 micron fractions was liberated and recoverable. This paper describes the steps taken to increase coarse particle recovery, overall plant recovery and the results achieved."

Jan 1, 2001

By W. W. Culver

The paper explores the substance, circumstances and significance of the Whelpley and Storer Copper Process. The 1866 Whelpley and Storer patent specified a process combining mechanical and chemical engineering. The process called for a down-drafting shaft furnace with a horizontal flue connected at the bottom of the shaft. Powdered sulphide ore was roasted in the shaft and then sent forward fully oxidized to a bath of sulphuric acid and/or calcium chloride. The “water furnace” was developed in Boston, at a time when the city was home to most Michigan copper mining companies. The process was field-tested at Quebec’s Harvey Hill copper mine. In 1865 James Douglas, Jr. took over management of the Harvey Hill mine with the challenge of saving the family investment. He needed a way to make money from low-grade sulphides. Through his relationship with chemist T. Sterry Hunt, Douglas learned of a possible way ahead using the process developed by Whelpley and Storer. The paper confirms the centrality of publications, meetings, and networking in the advancement of metallurgy. The process is of interest historically, as much as anything, because it is one of the pillars of James Douglas’ distinguished career in copper. INTRODUCTION At the 1866 meeting of the American Association for the Advancement of Science (AAAS) in Buffalo, New York, T. Sterry Hunt (1826–1892) read a paper “On the Metallurgical System of Messrs. Whelpley and Storer.” The paper is part of a chain of events that constitute the foundation of James Douglas’ (1837–1918) success in the copper mining industry. To understand the career of Douglas over the early years of modern copper mining, we must necessarily start with Whelpley and Storer. Going back to Hunt’s paper, he concluded his remarks by asserting that the Whelpley and Storer Process was “capable of such wide and varied application, that it is probably destined to have a very important influence on the industry of the world” (Hunt, 1867a). He reached this conclusion reasoning that the process had overcome a critical metallurgical hurdle (Hunt, 1867a). Hunt, a geo-chemist in modern terms, recalled that the chemist of those years easily separated copper from “sulphuretted” ores by converting it to a soluble salt from which pure metal was precipitated by “an equivalent of iron.” The problem was to “…apply this principle in the working of copper ores on a great scale...” (Hunt, 1867a). Hunt noted that this very problem had “…engaged the attention of many metallurgists, and has given rise to various processes for obtaining copper by the moist way, many of which are nearly or quite perfect in their operation, but are lacking in practicability and cheapness” (Hunt, 1867a). Hunt thought Whelpley and Storer had overcome the low-grade sulphide hurdle with a commercially viable engineering breakthrough. Yet in the history of copper metallurgy, the process is missing. What happened?

Jan 1, 2019

By Robert B. Hopler

Emplacing explosives in the borehole by bulk methods is utilized today for about 35% of all of the explosives used in the United States. Although different from today's methods, some bulk emplacement has been utilized throughout the history of explosives. This paper provides an overview of the evolution of the industry from primarily packaged to primarily bulk materials and methods.

Jan 1, 1992

By B. Schoevaerts

The ever-increasing depth of mineral extraction presents a challenging environment for hard-rock underground mines. High in situ stresses and associated seismicity with potential rockburst hazards are the major decisive factors contributing to the choice of a ground support regime. Conventional ground support systems, designed primarily for static loads, are not always capable of providing safe working conditions for underground personnel in seismically active mines. Systems specifically developed to resist dynamic loading and allowing for larger deformations are therefore preferred alternatives. High-tensile chain-link mesh has a proven record of successful use in open cut operations in various rockfall barrier installations due to its high energy absorption capacity. It has also been used in underground operations in various parts of the world. Its application in South African underground mining, however, is limited due to the high labour intensity. This paper describes a method of mechanized installation of a chain-link mesh as evaluation at Gold Fields' South Deep Gold mine situated some 45 km south-west of Johannesburg. A purpose-built mechanized roll mesh handler, developed in Australia, was used in this trial. The handler is compatible with all standard multi-boom underground drill rigs and is operated utilizing the hydraulic circuit normally used for the feed arrangement. A number of key performance indicators have been specified as success criteria by Gold Fields: ? A 30% faster installation compared to the conventional methodology ? The mesh should sustain any blast damage when applied to the blasting face ? No unravelling of the mesh when cut ? No failure of mesh under normal conditions ? Reliability of the MESHA® installation handler (availability >90% ? Compatibility of the MESHA® installation handler with AC 282 boomers. Although the energy-absorbing mesh combined with yielding rockbolts is a ground support system of choice for rockburst-prone conditions, the operational upsides recognized during the trial imply that this product can also be competitively used in less demanding ground conditions where weld mesh or shotcrete are customarily used as a primary surface support.

Jan 1, 2012

By Jarrod Bonsmann

"This paper presents the results of small scale testing to examine the effect of various importantparameters on the response of a vehicle due to the detonation of an explosive charge buried inthe soil below the vehicle. In particular, we were interested in examining what effect change instandoff distance, change in mass, and change in surface area would have on the loading applied.We examined the impulse delivered to the target in all cases and for the change in mass andchange in stand-off distance we examined impulse, kinetic energy, and acceleration."

Jan 1, 2012

By S Adamson

Morphological analysis of alluvial gold recovered from the same segment of a placer by four common commercial methods indicates that gold shape and the presence of quartz intergrowths or sulphide overgrowths substantially influence the recovery efficiency of each method. The amount and types of gold saved by each method varies according to the different hydrodynamic conditions under which each of the methods operates. Reverse circulation drilling has the lowest efficiency and preferentially loses moderate-high flatness gold and intergrown or overgrown gold particles with relatively low density. Gravity riffle, hydraulic riffle, and jigcentrifugal concentrator systems respectively save progressively more of these problematic gold morphotypes, but still lose significant and sometimes substantial amounts (of profit) to the tailings. Because of the differences in recovery efficiency, reverse circulation drilling probably underestimates the grade of most placers and may have resulted in bypassing several economic deposits. Losses to tailings by commercial recovery plants arise from inadequacies in fundamental plant design features. These inadequacies compromise plant efficiency by limiting the ability of plants to simulate the wide range of hydrodynamic conditions necessary to operate effectively throughout placer systems. Incorporation of sand pumps and multiple recovery methods into the more sophisticated plants only partly overcomes these inadequacies. At best, efficiency will be maximised in a few segments of the placer determined by individual plant design, and will decrease progressively upstream and downstream of those segments. Without prior knowledge of the morphological characteristics of the gold to be mined, it is difficult to choose the most appropriate plant design, or to estimate what proportion of the gold will be recoverable by any given plant. If the relevant relationships are not considered beforehand, the recovery plant is likely to lose a significant proportion of the gold, and sacrifice maximum profit.

Jan 1, 2001

By P. Roy

Smelting or converting of sulphide concentrates and mattes in a batch operation presents a challenge when directing the off- gas to a conventional acid plant. The Hindustan Zinc Ltd. (a division of the Vedanta Group of companies) Chanderia Lead Zinc smelter was presented with such a challenge that was met with the adoption of the Cansolv® SO2 Scrubbing System. The Ausmelt top submerged lance technology used at Hindustan Zinc generates a furnace gas stream that containsbetween 0.1 vol% and 12 vol% SO2 during the three stages of batch smelting. Cansolv® SO2 Scrubbing Technology captures the SO2 to ensure that treated flue gas exits the facility at a concentration below 100 ppmv SO2 and it releases SO2 in a controlled fashion, to more closely match the needs of the existing acid plant. The application of a regenerable scrubbing system to capture SO2 from a batch-operated furnace and convert it to acid in a conventional acid plant was a first of its kind in the world. This paper provides an update on the design and operation of the Hindustan Zinc SO2 recovery system and suggests two improvements to the basic flow sheet that optimize the cost of SO2 scrubbing further.

Jan 1, 2007