Search Documents

By D Pastars, J L. Mauk

Located at the southern end of the Awhitu Peninsula, the Waikato North Head ironsand mine is approximately 50 km southwest of Auckland . The ironsand deposit consists of Quaternary sands, clays and peats, formed by aeolian and marine processes. We sampled on widely- and closely-spaced intervals to test variability within the mining area. X-Ray powder diffraction shows that samples contain feldspars, quartz, pyroxenes, amphiboles, clays and titanomagnetite. Densities range from 1.6 to 2.5 grams/cubic centimetre, with porosities from 30 to 43 percent. The percentage of magnetic minerals values range from 0 to 75 percent, slimes (clay minerals) values of 0 to 26 percent and non-magnetic minerals from 20 to 95 percent. Mineralogical differences in the Mitiwai Formation and Waiuku Blacksand Member cause bimodal populations in the density, magnetic minerals, nonmagnetic minerals and slimes plots. The Mitiwai Formation has higher non-magnetic mineral values and lower density, slimes and magnetic mineral values than the Waiuku Blacksand Member.

Jan 1, 2001

For its Hellyer project, Aberfoyle sought to establish a high degree of confidence in all aspects of the feasibility study. Accurate capital and operating cost estimates were an integral and essential part of the study. They were crucial to the evaluation of investment returns and competitive cost position. Both the capital and operating cost estimates were based on the comprehensive data available from exploratory mine development, pilot plant operation, detailed engineering design, and Aberfoyle's experience in the area. One of the principal project objectives was to maximise operating productivity and efficiencies and this created capital cost alternatives which needed thorough cost-benefit assessment. The estimated capital cost for construction and development was $90 million, and the project was completed virtually on time for $80 million. The first year's experience indicated that operating costs would settle to well within 10% of the estimates.

Jan 1, 1990

By M. E. Alam

In the present study, 1.1 volume percent of nano size copper was incorporated into pure tin using hybrid microwave sintering assisted powder metallurgy route. Microwave sintered samples were extruded both at room temperature and at 230 °C. Microstructural characterization studies were conducted on the extruded samples to investigate the distribution characteristics of secondary phase and grain morphology. Room temperature tensile test results revealed that hot extruded Sn-Cu samples exhibited higher strengths (~ 41%, in case of 0.2% yield strength and ~ 38%, in case of ultimate tensile strength) and ductility (~ 15%) when compared to room temperature extruded samples. On the contrary, the tensile properties of pure tin remained independent of extrusion temperature. An attempt is made in this study to correlate the effect of extrusion temperature on the microstructural evolution and tensile properties of Sn-Cu solder.

Jan 1, 2009

By A C. Carter

The increasing need for alternative energy sources as well as the less clearly perceived but equally increasing demand for non-fuel minerals has resulted in extensive exploitation of near surface deposits. Many such deposits have depleted reserves and mining corporations are increasingly turning their attention to deposits, with thicker overburden, less competent materials, steeper dips and more complex structure. These deposits pose mine layout, geotechnical and equipment problems as well as the need for large outputs to achieve economies of scale. The paper describes the major problems and operational solutions for such deposits using continuous excavation and transport equipment.

Jan 1, 1980

By J. L. Fuentes-Cantillana, J. B. Solar Menéndez, A. O. Cámara

The Principality of Asturias is a region situated in Northern Spain with two centuries of tradition in underground coal mining. In addition, its uneven relief has obliged the construction of a great number of tunnels both for railways and roads. Basing on this experience and an ever increasing need to improve on safety, the Barredo Foundation dependent on the Regional Government and the University, provides and manages a Centre for Research of Fires and Ventilation in Tunnels. The Centre has as its most important infrastructure, a tunnel 540 m long, 9,5 m wide and 8,0 m high at centre. This section coupled with ventilation equipment allows the simulation of risk conditions at real scale, which is achieved by modifying the geometry of the section and through two powerful stations situated one at either en of the tunnel. In addition, the Centre houses two test benches for fans and electrical motors at high temperatures. One bench with a re-circulation conduit is the most appropriate for tests in Transversal and Semi-transversal type of installations. The other, is for the testing of electrical motors or fans which operate in zones where the surrounding temperature is high. In this Centre, training has also been developed for Fire Fighters and Civilian Protection Personnel who have to work in fire and smoke rescue conditions in underground structures. Testing conducted at real scale enables this formation and also to improve different computer programmes in the field of Fires and Ventilation.

Jan 1, 2003

The copper-clay deposits consist largely of goethite and clayey mudstones carrying native copper, cuprite, and chalcocite. The mudstones are of Ordovician age, are interbedded with Fe-Mn carbonates, and probably contained syngenetic iron and copper sulphides. The secondary copper minerals have been derived from post-Devonian weathering in situ and also by deposition from surfaee and underground waters draining the adjacent mineralized volcanic rocks.

Jan 1, 1969

By Monika Patrycja Polak - Micewicz

This paper presents an approach for estimating the fatigue life for the base of powered roof supports (shield) manufactured by the FAZOS roof support company. FAZOS?s powered roof supports are designed to operate on an inclined coal seam in full caving with a medium, strong roof strength. This shield support is utilized in conjunction with a shearer and face conveyor for a complete longwall mining system. To design shield support, it is essential for contractor to know the physical (hardness, toughness, etc.) and mechanical properties of material (tensile strength, Young?s modulus, etc.) used for the shield support as well as the geotechnical properties of the mine site. The fatigue strength of the shield support material depends on the mean stress, alternating stress, cycle frequency, transport dimensions, mine environment and other factors. In order to estimate the fatigue life for a powered roof support system, it is assumed in this paper that the support must keep the roof stable in the mine under variable load cycles. The approach selected in this study contains Goodman?s model (Goodman, 1899) for all blocks in the design housing which is subjected to sinusoidal load. On this basis, the degree of fatigue damage was calculated and compared to the results of experimental tests. It will be shown that there is a significant detrimental effect on the fatigue life of the base of the powered roof supports due to geometrical notches. The Ramberg-Osgood model and damage accumulation rule (Palmgren-Miner) (Miner M., 1945) were used and numerical analyses were conducted, utilizing ANSYS finite element software. These analyses play a very important role in longwall casing design. The proposed method allows assessment of the yield state and forecast of the structure cracking, taking plastic strains occurrence into account. The presented method is universal and can be applied for fatigue life estimation of other subassemblies of powered roof supports. The final portion of the paper presents results of variable amplitude loading simulations on the S355N and S690Q steel used to make powered roof supports. The results of the physical tests were compared with the results from finite element methods. The proposed approach to calculate fatigue life gives the best correlation between the experimental results and calculated values of fatigue life for the powered roof support base. Finally, the design process uses a simple approach to predict fatigue life in a short time, reducing design costs and providing longer service life for roof supports.

Jan 1, 2012

By J. H. Potgieter

This paper describes two cases of corrosion that occurred in dry-process, rotary, cement-clinker kilns. In the case of the kiln with five pre-heater stages, the attack occurred primarily from sulphates that probably originated in the raw feed and fuel being used in the plant and that penetrated the refractory lining. The corrosion was similar to ash-deposit corrosion often observed in steam boilers. In the second case the plant consisted of a long dry kiln with a single pre-heater fitted to the feed-end. In this case the corrosion could be ascribed to alkali chloride penetration through the refractory-brick lining and subsequent hot corrosion of the kiln shell.

Jan 1, 2004

By S. Eck

In previous work the influence of the casting speed on the flow field and the shape of the solidification front in an industrial 0.82 x 0.25 x 0.8 m³ bronze caster had been investigated. Both numerical and experimental model represented 1:1 the real caster geometry. A comparison of the results of both numerical and experimental models for the flow during the casting process showed a good agreement in the qualitative velocity fields (flow direction and vortex formation). This work represents a parameter study of the numerical model with variations of the turbulence conditions at the inlet in order to clarify their influence on the flow field in the caster. In order to find the best boundary condition at the inlet, the numerical calculations for water have been compared with the measured flow fields in the water model. The new boundary conditions were then applied to the numerical model of the bronze casting process.

Jan 1, 2009

The outlook for suppliers of energy to the expanding economies of the Pacific Basin region is essentially positive, but particularly for exporters of high quality steam coal. This paper argues that economic growth in the Pacific Basin region has exceeded world economic growth for some years and that this will continue to be the case for the next decade at least. It looks briefly at the link between economic growth and energy demand and at the relationship between energy demand and the demand for electricity. Changing preferences in fuel mix for electrical generation in the region are noted and tentative forecasts made about variations in this mix. The pros and cons of various forms of fuel used to generate electricity are considered from the point of view of the consumer. Having concluded that steaming coal in particular is likely to become even more important as a generator of base load electricity, the paper looks at the opportunities this presents for exporters such as Australia, and touches on some factors that could prevent development of those opportunities. This paper will concentrate on electrical energy. For the purposes of this paper, the Pacific Basin refers essentially to Australia, New Zealand and the Asian countries bordering the Western Pacific. As a supplier, Siberia is not included because, although it has great potential, it is thought that problems of climate, infrastructure and political restructuring will delay the realisation of that potential until the next century. Although it deals with the Pacific Basin region, where many countries are industrialising rapidly from a predominantly agricultural base, it looks at the experience of mature industrial DECD economies where their experiences seem relevant.

Jan 1, 1990

By Lyman G. J

Magnetic separator operation in the recovery of magnetite in heavy medium circuits was studied by conducting a series of tests on a full size wet drum magnetic separator.The significant operational variables were found to be feed pan clearance, squeeze pan clearance, dry magnetite feed rate and separator drum speed. With feed and squeeze pan clearances optimized for typical primary separator operation, magnetite loss and concentrate specific gravity were found to be related in a regular manner to dry magnetite feed rate at any drum speed.A two component model of magnetite loss is proposed, relating total magnetite loss to losses in the feed pan and squeeze pan zones. The experimental curves relating magnetite loss to dry magnetite feed rate at the various drum speeds are interpreted in terms of the two component model.The magnetite particle size distribution in the separator was also examined. The tailings magnetite was found to be finer than the feed magnetite only when the dry magnetite feed rate was low, or immediately following the introduction of a new charge of magnetite when the separator was fed at an intermediate dry magnetite feed rate.

Jan 1, 1983

By V. D. del Valle, T. G. Joseph, J. J. Berezan

Aggressive driving patterns, rough and poorly maintained roads and pit floors, along with the occasional bump and poorly placed load from a shovel can create intense and sometimes serious vibration levels on a heavy hauler. The effects of high vibration have been shown to be of concern for the health of the operator as well as the reliability of the equipment. It is proposed that an onboard vibration warning system based on the ISO 2631-1 standard could be used to help operators reduce the vibration levels experienced in a heavy hauler. The onboard system would consist of a screen that displays the instantaneous vibration in the form of three lights: green (safe zone), yellow (cautious zone), and red (danger zone), as well as an overall vibration exposure or dose for the entire shift. With the utilization of the warning system, it is anticipated that the overall vibration levels will be decreased resulting in improved operator health, a reduction of vibration-induced maintenance, and improved haul roads through reduced impact loading and repair for localized trouble areas.

Jan 1, 2004

By Richard Burt

"In seeking to supply the ever increasing needs for raw materials, the mining industry has been required to develop lower grade resources in increasingly remote regions of the world. This has resulted in the extension of many frontiers, both technologically and geographically.The accent of mineral processing research over the last few decades has been to “do existing things better”. There have been many breakthroughs in equipment and processes; however in general the accent has been to increase capacity of existing unit processes, often by orders of magnitude, or to refine the process itself by basic research and development. This has lead to added sophistication, enabling the process engineer to maintain optimum performance of his equipment while reducing the cost, and the amount of labour needed to operate the plant.While much of the increased requirement for resources is handled by the development of ever larger, lower grade orebodies, a significant portion still comes from the small miner - even the artisanal miner - operating in remote and often politically sensitive parts of the world. For them, innovation and simplicity are the keys, not sophistication.The tension between sophistication and simplicity - or research and reality - is specially evident in the area of gravity concentration of rare metals, such as tin and tantalum. This paper looks at this tension, primarily from the eyes of an operator and seeks to put into perspective the two paradigms."

Jan 1, 1999

By Warren E. Morrison

The first major evaluation of the nation's raw materials prospects after World War II was completed by the President's Materials Policy Commission (Paley Commission) in 1952 and submitted to the President in June of that year, as a five-volume study entitled Resources for Freedom. The bulk of the report was devoted to an analysis of the past, present, and probable future of the Nation's mineral supply industries. The Commission's evaluation of the future situation regarding minerals was derived from its forecasts of the probable domestic demand for the major minerals in the 1970's. This demand analysis was made in the context of probable worldwide demand. Several crucial assumptions were made by the Commission's fore-casters. It was assumed in 1950 that the next 20 to 30 years would see no major wars and be a period of sustained economic growth. Another assumption was that the anticipated demand for raw materials must be supplied at essentially no increase in real cost in order to avoid crucial supply problems. The Commission's forecasts were derived within the context of the country's expected future rate of economic activity. The gross national product (GNP) growth to 1975 was derived from projections of the number of people in the labor force, hours of work, and an index of probable production measured per unit of labor input. It was believed labor hours would decrease and labor productivity would increase. The result was a forecast GNP growth rate of 3 percent.

Jan 1, 1970

By Shawna Munn, Jakub Hudler

This paper outlines the use of tunneling headwall softeyes for transit construction projects in the Greater Toronto Area (GTA) over the past decade. Due to spatial constraints, tunnel boring machines were used to construct the underground tunnels requiring the design of launch and exit shafts with headwall softeyes to facilitate tunneling operations. Variable ground conditions and shaft geometries lead to the development of innovative headwall and tunnel softeye design applications using fiber reinforced polymer (FRP) elements (beams, reinforcing bars, and tiebacks). This paper outlines the challenges and benefits associated with designing and constructing shafts using various systems. Lessons learned throughout design and construction of more than 20 structures over the past 10 years are outlined. The constructability challenges with using FRP and design performance are also discussed. For over a decade, the City of Toronto has been expanding its metropolitan transit network with a variety of new transit construction projects. Two recent projects in the Greater Toronto Area (GTA) for underground infrastructure include the Toronto York Spadina Subway Extension and the Eglinton Crosstown Light Rail Transit project. These add a total of 31 new stations and 18.6 km (11.5 miles) of underground transit (TTC 2017) (EllisDon 2016). Due to ground conditions and spatial constraints of existing surface infrastructure, these projects utilized tunnel boring machines (TBMs) to construct the underground tunnels requiring the design of various types of shafts and headwalls to facilitate underground tunneling operations. To allow for tunneling through the headwalls, these shafts were designed with “softeyes” - a section of the wall without metal reinforcement that allows the TBMs to tunnel through.

Jan 1, 2018

Sulphuric acid leaching at atmospheric pressure of a number of Australian nickeliferous laterites was examined in detail. The results obtained indicate that nickel can be extracted from these ores, although the conditions required to achieve about 90 per cent extraction vary widely. These differences in reactivity can be related to the types of nickel-bearing minerals present.Nickel is more readily extracted from nickel-bearing clays such as chlorite, than it is from nickel-containing goethite.The results clearly show the problems associated with the processing of complex ores such as the nickeliferous laterites, and they indicate the need for complete characterization of each deposit.

Jan 1, 1978

By C D. Rawlings

An assessment is made of the potential for thick seam underground mining of black coal in Australia. A brief summary is given of the geo-mechanical environment and previous mining history existing in a number of areas of particular interest from the point of view of thick seam mining. A classification of thick seam mining methods is presented with emphasis on the critical geo-mechanical parameters influencing the performance of such methods. A summary is made of perceived geo-mechanical research requirements related to thick seam mining in Australian coalfields.

Jan 1, 1980

By Manuel Pérez-Tello, María M. Salazar-Campoy, Óscar Rodríguez-Hoyos

A common problem during the operation of the Kaldo furnace is the formation of accretions and blockage of the injection lance due to splashing. This typically occurs during the processing of anodic slimes for the production of doré. In this work, a 1:7 scale model of the Kaldo furnace currently in operation at Metalúrgica de Cobre, Mexico, was built in transparent acrylic plastic. Water and colored oil were used to represent the doré and slag, respectively. The model was used to determine the maximum penetration distance of the injection lance under a variety of experimental conditions at room temperature. Input variables included two types of oil, rotation speed, inclination angle, and the fraction of the vessel volume occupied by the liquids (φ). A mathematical correlation for the dimensionless maximum penetration distance of the injection lance d ∗ as a function of φ, the Froude number of the liquids in the vessel (Fr), the Reynolds number of the gas jet (Re), and the oil-to-water kinematic viscosity ratio (η)was developed. Reasonable agreement between the calculated and experimental values was obtained. Digital images showed that splashing was caused by the turbulent gas jet impinging upon the free surface of the liquids, whereas the cascade effect was negligible. The results of this work have been useful to improve the operation of an industrial Kaldo reactor.

By A. Eccles

Phase designs are the foundation upon which all open pit mine sequence optimizations and budgets should be built. Unfortunately, at times, mine engineers skip the step of developing realistic pit phase designs - designs that include access ramps and mineable widths. Without mineable phase designs, their optimized schedules are based on theoretical pit shells or ?quick-and-dirty? plans with no ramps. The output from such optimizations is almost always overly optimistic. Without mineable designs, the production estimates are misleading, because they overestimate ore, and underestimate waste stripping requirements. Worse yet, when plans are not based on realistic phase designs, they can point to exactly the wrong decision in feasibility studies (i.e. ?go? when it should be ?no-go?). This paper discusses the importance and features of good pit phase design, and demonstrates the pitfalls of relying on optimized production sequences that are not based on properly designed pit phases.

Feb 27, 2013

By Harry Schnabel

A 6200 m² cement deep soil mixed (CDSM) wall was constructed for an addition to the Museum of Fine Arts in Boston, Massachusetts. The addition was located along the east side of the existing museum within an existing courtyard and in the area of a recently demolished structure. The basement for the new addition extended up to 9.1 m below the floor slabs of the adjacent buildings. The adjacent buildings are supported on a variety of foundations including; shallow spread footings on alluvial sand deposits, low capacity piles bearing in the alluvial sands and Boston blue clay, and caissons bearing on the alluvial sands and clay. Groundwater was less than one meter below the top of the CDSM wall. The new addition was founded on shallow foundations in the desiccated crust of the Boston Blue Clay. The CDSM wall was selected as the most economical means to control deep seated ground movements, limit movements of adjacent structures, and inhibit groundwater flow into the excavation. Braces and a continuous wale were used to support the CDSM wall where it was located adjacent to structures. Tiebacks were used where there were no structures. Other geotechnical construction at the site included: ? Jet grouting (JG) to improve the ground and provide an impervious subgrade layer at the west end of the addition, ? Concrete pier underpinning was used to support an existing structure on the west end of the site, and ? A secant pile wall using alternating drilled shafts and jet grout columns was used for earth support and a barrier to groundwater flow to allow for the installation of a storage tank at the south end of the site. Inclinometers, total station surveying, vibrating wire strain gauges on the braces and wales and load cells on the tiebacks were used to monitor performance of the excavation support system. The excavation support system performed better than required limiting lateral movements of the adjacent structures to less than 13 mm and vertical settlement to less than 8 mm. No settlements or movement were detected during the construction of the wall. Lateral movement of the CDSM wall was typically below 15 mm with the maximum movement occurring near subgrade.

Jan 1, 2011