Search Documents

By Tsunenobu Nozaki

"AbstractThe PRESS-IN METHOD is widely recognised as “an environmentally friendly piling method”. However, this characteristic is only one of the fundamental advantages of the method and this paper presents the most up-to-date capabilities of the method. Due to the evolution in recent years, the Press-in Method is now applicable to 2.5m thick retaining walls, over 50m deep foundations, overcoming rock conditions and confined construction conditions.The Press-in PrinciplesThe basis of the Press-in Method is simple. The Silent Piler presses a pre-formed displacement pile into the ground by static jacking force. The reaction for the Press-in Force is generated by gripping previously installed piles. As a pile is pressed into the ground, “A Pressure Bulb” is formed around the pile toe. Accordingly, higher bearing capacity can be generated compared to driven piles without disturbing the ground and producing any vibration. (A comparison of jacked, driven and bored piles in sand (2005), Deeks et al.)Applicable Pile ProfileThe Press-in Method is applicable to most of the steel piles available on global market i.e. U sheet pile in single form and pair, Z sheet pile, also in single and pair and Tubular Pile as described in Figure 2. Wall thickness of those piles can be 0.3m to 2.5m and moment of inertia of the wall ranges up to about nine million biquadratic cm per meter, which can deliver similar elastic modulus EI (kNm2/m) to 2.0m thick diaphragm walls and can be utilised for extremely deep excavations required in today’s construction industry"

Jan 1, 2014

By C. Kloppers

The aim of this investigation was to reduce the cost of primary steel de-oxidation by substitution of aluminium primary de-oxidation with a practice that uses carbon. The cost of carbon is four times lower than that of aluminium. The application of carbon would directly result in raw material cost savings. Investigations were conducted at Iscor?s Newcastle steel plant on various steel grades. Specific production aspects were emphasized to ensure that the cost savings accrued would not create secondary expenses. These production aspects entailed: ?Yields on de-oxidation elements ?De-oxidation capabilities ?Alloying yields (Mn and Si) ?Carbon-pickup ?Nitrogen-pickup ?Temperature loss during tap ?Steel cleanliness ?Slag morphology. This project proved that carbon de-oxidation, apart from reducing de-oxidation raw material cost due to cheaper raw materials being used and lower consumption rates, resulted in steel that is cleaner and has lower nitrogen concentrations. Carbon primary de-oxidation has been implemented at Iscor?s Newcastle plant on a large range of steel grades, ranging from ultra-high carbon (> 0.60% C) to ultra-low carbon (< 0.03% C) grades. A net saving of between R100 000 and R200 000 per month was achieved.

Jan 1, 2001

By John J. Sammarco

Mining has one of the highest annual average fatality rates among major US industries. Health and safety dangers have been inherent to mining since the early days of picks and shovels. Even though miners’ health and safety has improved over the years, mining is still one of the most dangerous occupations. Mining was traditionally a low tech industry. It is now driven by competitive pressures to go high-tech by using programmable electronics (PE) for machine control, atmospheric monitoring and material processing. The industry’s experience with the functional safety of PE is limited compared with other industries. Thus, PE is an emerging technology for mining that can potentially create or worsen hazards.

Jan 1, 1999

By Ludovic Charpentier

Production of metallic wires directly from liquid jets would avoid drawbacks of extrusion (space needed, damaging, cost?) and enable recycling. But liquid jets tend to break, due to capillary instabilities, unless a solid layer (coating or start of solidification) surrounds it. We recently developed a process to produce tin wires, cooled by water flow parallel to the jet. Superficial oxidization of tin produces a glass coating around the jet. Studies showed the length of wires increased when increasing speed of tin jets, and that water average speed should be the closest possible to the jet one to have smooth fibers. Producing 1 mm diameter wires is possible. The length of wires is limited by the experimental setup, which does not provide possibilities to coil the wire. Most of other metals do not generate glass-like oxides. The lack of coatings makes it necessary to reduce the capillary instabilities to obtain fibers.

Jan 1, 2006

By Anthony T. Xannacchione, Luis E. Vallejo

At present, there is little knowledge concerning the shear strength of clays containing floating rock particles with concentrations from 0 to 30%. In practice, the effect of rock particles is typically disregarded in shear strength analysis The two primary reasons for this are: 1) a lack of agreement concerning the influence of rock particles on material strength, and 2) the expense and difficulty of testing day-rack mixtures with existing laboratory procedures. These factors have impeded the development of successful slope remediation design techniques far colluviums derived from resistant sedimentary rocks or spoil produced from surface mining. This study reviewed 3 1 technical papers which contain analysis of shear strengths for clay and sands with varying mixtures of rock particles. These technical papers, published over the last 40 years, are comprised of field case studies, laboratory evaluations, and theoretical analysis. Evaluation of this body of knowledge ha shown that the shear strength gradually increases with increasing percentages of floating particles in unsaturated clays.

By D. R. Parrish, F. F. Craig

In some respects, forward combustion (alias: fie-flooding, underground combustion, in-situ combustion, dry combustion) is an efficient oil recovery method. For example, its displacement efficiency (as much as 95 percent in reservoirs with high porosity and high oil saturation) is good. In its use of heat, however, forward combustion is grossly inefficient. Most of the heat generated during forward combustion is wasted. About one-fifth of the heat is picked up by the incoming air and re-used (regenerated); the remainder is left behind the combustion zone and ultimately is lost. Compressed air is expensive, and heat generated from compressed air via underground combustion is too valuable to be thrown away. Improvement is needed. Since the early 1950&apos;s, improvements in forward combustion by addition of water injection have been discussed, particularly in the patent literature, with increasing frequency.&apos;-&apos;&apos; These concepts are based on the fact that relatively inexpensive water can be used to pick up much of the heat that is ordinarily wasted during forward combustion, and transport it forward to a more useful place, thereby reducing the amount of air required to move a heat front through the reservoir. Several approaches have been proposed. Merriam and Squires1 taught that a combustible (fuel) gas should be injected along with the air and water. This, however, would give at least a tendency toward reverse combustion instead of forward combustion, and would reduce the velocity of the heat bank, defeating the primary purpose of the water injection. Pelzer2 described primarily a batchwise method of forward combustion and water flooding. He advocated burning part way through a reservoir with forward combustion, then switching from air to water injection alone to push the heat toward the producing wells. Though possible, this method has serious disadvantages, the major one being that, by the time water injection is started, much of the heat has been irretrievably lost to the overlying and underlying formations. We have described what is considered a practical Combination Of Forward Combustion And Water-flooding (COFCAW).3,4 Air and water are injected simultaneously (or alternately) after a small heat bank has been formed by forward combustion. Some of the injected fluid fills up the region behind the heat bank; the rest enters the heat bank. Upon encountering heated rock, the water is converted into steam, which then flows ahead of the combustion zone and displaces much of the oil in place. Only enough air is injected to provide heat for vaporization of the water and to compensate for reservoir heat losses. Since the size of the heat bank is minimized, heat losses also are minimized. Because of more efficient oil displacement ahead of the combustion zone, fuel consumption is reduced. Too, unlike a forward combustion zone that cannot move until all fuel at a point has been consumed, COFCAW leaves some

Jan 1, 1970

By Peter Wells, Adrian Sabau, Turgut Yalcin

"The nickel ores of Sudbury contain substantial amounts of the gangue mineral pyrrhotite (Fe7S&) which causes certain diflculties in the milling of these ores. This paper proposes a process called “magnetoflotation” as an effective means of dealing with pyrrhotite. The method reduces the pyrrhotite content of concentrates by applying a magneticjield on the path product as it leaves the flotation cell.Successful performance of magnetoflotation requires the optimization of several variables. In this study, three of the variables (air flowrate, collector concentration, pother concentration) were investigated by Box- Wilson experimental design, and others (magnet speed, grind size, pulp density, flotation time) were examined individually. The process was tested on a Falconbridge nickel ore, assaying 1.92% Ni, and under the best operating conditions, a concentrate was obtained with 13.56% Ni grade and 74.32% recovery in a single step. Further improvements to grade and recovery were possible by cleaning and scavenging. The same ore was also tested with conventional methods for comparison, and results indicated that magnetoflotation performed better.INTRODUCTION“Magnetoflotation” refers to the process of carrying out magnetic separation and flotation simultaneously within the same device, and is intended to prevent magnetic minerals from reporting to the froth products while non-magnetic minerals are being floated. Typical cases where this method might be beneficial include the processing of magnetite and nickel ores. Its use on magnetite ores has been reported elsewhere [Yalcin, 1992; Yalcin, 19931. This paper describes its application to nickel ores, more specifically to the nickel ore of Falconbridge Limited in Sudbury."

Jan 1, 1999

By S. Rivard

"This paper demonstrates the selection of grinding circuit technology for a number of recent projects including discussion of the key drivers and the role of energy efficiency. Decreasing head grades combined with a strong and sustained increase in operating costs has forced miners to examine increased project size, increased equipment capacity and efficiency improvements in order to reduce their unit operating costs and improve overall project economics. Comminution energy consumption, safety and capital cost considerations play a critical role in the success of projects. This paper presents some key guidelines for a successful and cost effective comminution circuit design and includes a case study on three projects, outlining the issues and the drivers which led to the ultimate circuit selection and the critical role that energy efficiency played.IntroductionComminution circuits for minerals processing are selected based on their suitability and efficiency in reducing run-of-mine ore to the desired feed size for the downstream process. The input material (ore) properties and downstream process requirements are the key determinants and there are standard approaches for each circumstance.The minerals processing industry has been a fast adaptor of efficiency improvements based on increasing capacity of equipment (e.g. trucks, crushers, mills, pumps) but less successful in adapting radically new technologies that disrupt incumbent flowsheets or processes.The installed power of grinding mills has increased linearly over the past 25 years (Meka & Lane, 2010) and pumps and classification equipment have kept pace. The autogenous grinding (AG) and semi- autogenous grinding (SAG) mills displaced stage crushing as a dominant method of coarse rock breakage in many applications causing crusher manufactures to increase the capacity of cone crushers to meet the competitive demand.Examples of new comminution technology in the 20th and 21st centuries are the development and adoption of cyclone classification in the 1940s (Newtech, 2016), AG milling in the late 1950s, vertical grinding mills in the 1980s, high pressure grinding rolls (HPGRs) also in the 1980s and ultrafine milling technology in the 1990s (Meka & Lane, 2010)."

Jan 1, 2017

By J. W. Thompson

This work is a codification and annotation of the Congressional enactments relating to minerals, mineral lands, and mining. It covers every enactment of Congress from the original ordinance of 1785 to the present time, as well as all sections of the Revised Statutes of the United States relating to these subjects. These laws are grouped according to their general subject matter, and are arranged thereunder in numerical or chronological order. Many of the mining statutes include matter not pertinent to the subject, and only those parts of such acts are quoted as will properly show their relation to minerals and mineral lands and indicate how they should be construed. Some mining acts have been repealed or have become obsolete, and others have become incorporated substantially in sections of the Re- vised Statutes; but these are retained in order to show the changes made, and the constructions placed thereon by the courts are given as aids in construing the new or repealing acts. The annotations consist of legal propositions abstracted from the decisions of the various courts and executive officers of the Govern- ment that have interpreted the sections and statutes so codified. These legal propositions are arranged under the different sections and acts with appropriate headings, titles, and subtitles, in logical order, exhibiting the present status of each particular section or act and its application to the subject of mines and mineral lands. The annotations do not purport to be abstracts of decisions on the sub- stantive law of mines and mining generally, but are limited strictly to the interpretation placed on a given section or act definitely re- ferred to by a court or executive officer by the number of the section of the Revised Statutes or the volume and page of the Statutes at Large in which the Congressional enactment is found. It may be observed that the legal propositions stated are not always pertinent to the particular section or act under which they are classed and of which they purport to give a construction. The arrangement, however, is not an arbitrary one, but is so made for the reason that the courts or officers in the construction of a particular section or act definitely referred to by number or volume and page incorporated in the decision matter not strictly pertinent to the par- ticular section or act so designated. This statement applies especially to the interpretations placed on the sections of the Revised Statutes. The decisions abstracted for the purpose of this work are those of the United States Supreme Court, 234 volumes; the various Federal courts, 214 volumes; the decisions of the Department of the Interior

Jan 1, 1915

By W. H. Schiffbauer

NIOSH has developed an active proximity warning system called HASARD (Hazardous Area Signaling and Ranging Device) for warning workers as they approach known dangerous areas around heavy mining equipment and other dangerous work zones. HASARD is composed of a transmitter and a receiver. The transmitter generates a 60-kHz magnetic field using one or more wire loop antennas. Each antenna is adjusted to establish a magnetic field pattern for each hazardous area. The receiver, worn by the worker, is a magnetic field strength meter. The received signal is compared against preset levels which are calibrated to identify levels of danger. The receiver outputs can include visual, audible, and vibratory indicators and it can also be made to disable machine functions. HASARD was field tested on a Joy 12 continuous miner, a Komatsu 210 M Haulpak, and on a highwall launch vehicle. Slight modifications were made for each application. HASARD provided warnings as designed and proved to be rugged enough to withstand the harshest of production environments.

Jan 1, 2001

By V. A. Marple

At the Twin Cities "lining Research Center (TCMRC) a project is underway to determine how varying the parameters of a coal-cutting process would affect the amount and the size distribution of the generated dust. The cutting parameters being investigated are the cutting speed, depth of cut and shape of the cutting, tool. To accomplish this research ft is necessary to collect and transport the coal dust venerated at the cutting tool to measuring instruments for analysis. The purpose of this contract was to develop and deliver a system of instruments for measuring the size distributions of the generated coal dust. The instruments employed are essentially those developed for particulate air pollution measurements (1, 2). The instrument system covers a particle size range of 0.005 to 20 microns and is capable of performing in situ measurement and presenting data in real time.

Jan 1, 1974

By Dipak Sengupta

This study analyzes the safety, technology, and economic impact of eliminating safety fuse from metal/nonmetal mines, based on operation and manufacturer experience over the past five to ten years. If safety fuse is eliminated, blasting accidents will decrease with no technical impact except for some limited, specific applications. The economic impact will be minor for large operations, but will be significant enough for small operations that some small operations will likely close rather than change. The majority of the mines would probably change over, with the extra cost absorbed by the market. Elimination of safety fuse would have obvious impact on the two manufacturers of safety fuse; one manufacturer already produces an alternative system, and will remain unaffected; the other will be affected if they do not change their production strategy. There will be a very minor effect on the mining industry as a whole due to abolishment of safety fuse from the standpoint of employment or production.

Jan 1, 1980

By D. V. Keller

Black lung disease, or paeumocomosis, is a serious health hazard for workers working in a coal mine. Though the exact cause of black lung disease is not known, it is certain that prolonged inhalation of fine coal particles, ever present in the mines, does give rise to black lung disease. For a long time, it also has been known that limestone applied to coal dust mine surfaces tends to hold down coal dust thus preventing it from refloating in the air of the coal mines. Since the humidity in the mines may be generally high, this also might be an important factor in the particular substrate system behavior. Fine solid particles stick to other particles and surfaces very indiscriminately. The term adhesion is used for the phenomenon of attachment of particles to surfaces whereas cohesion is used for the phenomenon of attachment of particles to each other. The measurement of the force of adhesion of coal particles to coal substrates presents a great problem, especially in the case of particles in the size range of a few microns. These micron sized particles are at the limit of the resolution of the optical microscope and therefore an electron microscope has to be used for this purpose. The forces of adhesion between these particles and substrate may be very strong and can exceed the weight of the particle by four to five orders of magnitude.

Jan 1, 1973

By John R. Rhodes

The objective of this project was to investigate the feasibility of analytical techniques potentially capable of determination of Mg, Al, Si, S, Ca and Fe in 1 to 2 mg samples of respirable coal mine dust, in a total analysis time of not more than 10 minutes per sample, using equipment capable of being truck mounted for field-laboratory operation. It was not essential that the technique be non-destructive, but the chosen technique is, and this enables the analysis to be performed directly on the 37 mm diameter membrane filter on which the respirable dust sample is normally collected. The sensitivity requirements are therefore quoted in terms of the units of measurement, µg/cm2. The detection limit (3o of the background criterion) should be 0.5 µg/cm2 or less. The precision should be 5% or better, at concentrations above which the detection limit is not the determining factor.

Jan 1, 1972

By Matthew N. Rubin

This report summarizes the work performed under USBM Contract No. H0155155. The purpose of this work was to obtain operational data on retrofit noise control treatments suitable for use in coal preparation plants. This data was obtained by evaluating the performance of four categories of noise control treatments which were installed in a commercial coal preparation plant. The four categories of treatments were resilient screen decks, resilient impact pads, chute liners, and curtains. The selection, installation and initial evaluation of the treatments was documented in the Volume I report issued in 1977. This Volume II report summarizes the results of the long-term evaluation of the original treatments, as well as some additional tests which were conducted on elastomer-clad (resilient) screen decks. This project demonstrated the feasibility of a number of retrofit noise control treatments, some of which also proved to be quite durable over the long term.

Jan 1, 1982

By Robert E. Manning

At present, a need exists for more effective noise control in the coal-mining industry. In particular, new muffler designs with the required acoustic performance are needed for percussive pneumatic drills. Accordingly, the U. S. Bureau of Mines issued a contract to USS Engineers and Consultants to design a muffler capable of attenuating the noise from the air exhaust of a pneumatic drill. The specific objective of the contract was to design and deliver a prototype muffler that would attenuate the air-exhaust noise to 90 decibels on the A scale (90 dbA). The test drill used in this investigation was one used for roof-bolting purposes in coal mines. Using the combined approach of analysis by digital-computer program and experiment by simulated-noise tests, three prototype mufflers were designed and constructed at U. S. Steel Research. The mufflers consisted of a variety of resonator chambers and expansion-contraction chambers, and were of the following sizes: A muffler with a 3- by 5-inch elliptical cross section and about 8 inches in length. A muffler 5 inches in diameter and about 5-1/2 inches in length. A muffler 5 inches in diameter and about 10-1/2 inches in length. These mufflers were subjected to laboratory tests to determine their effectiveness in attenuating exhaust noise, mechanical noise, total drill noise, and simulated noise. All mufflers reduced the exhaust-noise level by about 25 dbA - from about 115 dbA without a muffler to below 90 dbA with a muffler - and thus were successful in meeting the contract objective. Field tests were conducted with the three prototype mufflers at U. S. Steel&apos;s Robena No. 4 Mine, and no icing problem was encountered. A fourth prototype muffler was designed to fit around the leg of the pneumatic drill. Tests showed that this kidney-shaped muffler also reduced the air-exhaust noise to below 90 dbA.

Jan 1, 1973

By John C. Machisak

INJURY EXPERIENCE AND EMPLOYMENT DATA on all stone quarries and associated plants in the United States are presented in this publication for the calendar year 1959. Such related operations as the manufacture of cement and lime and rock dressing are included. Data on clay and sand and gravel operations are not included and will be found in other Bureau publications on injuries and employment. The Bureau is authorized to make requests for such data and the information voluntarily submitted by the operators contributes to the promotion of safety in the quarrying industry. Every effort has been made to make this canvass as complete as possible. Data for production workers and office employees at the quarry site are included.

Jan 1, 1963

By John C. Machisak

INJURY EXPERIENCE AND EMPLOYMENT DATA on all stone quarries and associated plants in the United States are presented in this publication for the calendar year 1959. Such related operations as the manufacture of cement and lime and rock dressing are included. Data on clay and sand and gravel operations are not included and will be found in other Bureau publications on injuries and employment. The Bureau is authorized to make requests for such data and the information voluntarily submitted by the operators contributes to the promotion of safety in the quarrying industry. Every effort has been made to make this canvass as complete as possible. Data for production workers and office employees at the quarry site are included.

Jan 1, 1963

By David R. Alison

This study was conducted using field interview methods to determine the data and information requirements of the underground coal mining industry for improving mine ground control procedures in existing and future mines. The establishment of a central geologic and engineering information resource center with computer searchable abstract files that can locate and supply descriptive and case-study literature addressing specific mining problems is recommended. Research done under Bureau of Mines Contract J0395010, includes a Bibliography of Underground Coal Mine Ground Control Literature.

Jan 1, 1980

By C. Lurie

This final report describes the work performed by Gulton Battery Corporation under USBM Contract No. HO-112033, entitled "Research and Development on Lithium-Nickel Fluoride Batteries For Mint Life Support Equipment". The lithium-nickel fluoride couple was chosen For this investigation because of its high theoretical energy density (626 Wh/lb), its ability to operate at ambient temperatures and the fact that it showed promise as a secondary system. The theoretical energy density of the lithium-nickel fluoride couple is ten times greater than that of the widely used lead-acid battery and three times greater than the silver-zinc battery which has the highest theoretical energy density of the commercially available secondary systems. The experimental program first evaluated the cell components individually. The results of these studies then formed the basis for investigations of cell performance using experimental three-plate cells. These cells consisted of one nickel-fluoride and two lithium electrodes. All work was performed in a glove box under an argon atmosphere which was sufficiently pure to maintain the shiny appearance on freshly prepared lithium surfaces. The major portion of the work effort was concerned with the nickel fluoride electrode. Binder, conductive diluent, fabrication technique, as well as the nickel fluoride active material itself, were considered. Criteria for binder materials were established and six classes of materials encompassing thirteen binders were evaluated. The candidate materials were initially screened for appropriate chemical and physical properties and finally evaluated in three.-plate cells, Two epoxy powders emerged as the most promising binders. Two types of conductive diluent were evaluated. The first is a carbon black of low bulk density and high surface area. This material is a good conductive diluent; however, electrodes fabricated with it lacked good mechanical strength. It was hypothesized that a uni¬form, small particle size, low specific surface area would improve the mechanical properties of the electrodes. Therefore, two samples of graphicic materials, milled to uniform powders in the one-to-ten micron range were evaluated. Electrodes prepared with the graphitic materials had superior mechanical properties, However, their electrical performance was significantly poorer and voltage losses of 0.2 to 0.3 volts were observed. Several electrolyte solutions were evaluated. N-Methyl-2-Pyrrolidone was tested but found to be incompatible in the presence of lithium. Lithium perchlorate, lithium hexafluoroarsenate, and lithium bromide were tested as two-component electrolytes in propylene carbonate solvent and their performance compared with that of the single electrolyte solutions, Lithium perchlorate gave the best performance. Lithium hexafluoroarsenate was also evaluated in methyl formate and appears to give equivalent performance. The lithium perchlorate-propylene carbonate system is preferred as it is easier to handle and less expensive.

Jan 1, 1973