Search Documents

By Robert Stefanko

With passage of the Clean Streams Act of the Commonwealth of Pennsylvania and its impact on the coal industry, considerable research has been conducted to explore various approaches to the problem, including deep-well disposal. Available drillhole data from gas and oil wells were used to develop cross -sectional maps for various portions of the state and potential disposal zones were evaluated. Bethlehem Mines Corp., faced with a severe water problem at its Marianna operation in Washington County, cooperated with the Dept. of Mining at The Pennsylvania State University in establishing a 1500-ft well into the Salt Sands for the purpose of determining the feasibility of mine water disposal. The thickness, porosity, and permeability of the formation at the well site proved to be below what had been anticipated from drillhole data. Further, subsequent hydraulic fracturing did not improve the flow characteristics of the well; pumping pressures remained in the range of 1800-2000 psig for disposing of water at the rate of 150 gpm. The legal problems of disposal at the site were very formidable. When the Salt Sands proved to be less than satisfactory, permission could not be obtained to dispose in other promising formations. The paper details many of the problems associated with the experimental well and makes an assessment of the potential for deep-well disposal of mine water. The concept of disposing of liquid industrial wastes by deep-well injection is not a new one. Brines associated with crude oil long have been disposed of in this manner, with the additional benefit of aiding secondary oil recovery. More recently, with the expansion of nuclear energy, the lethal, highly radioactive wastes which are by-products of the fission process have created severe disposal problems. During the past ten years, a variety of industries have resorted to subsurface disposal, some of the details of which are given e1sewhere.l,2 The list reveals wide variations in injection rate, pumping pressure, cost, and waste disposition. Included are successful installations in Western Pennsylvania. Enactment of more restrictive clean-water legislation in Pennsylvania recently had a great impact on the coal industry. Among its provisions was the reclassifica-tion of most mine water as industrial waste whose dis-posal is prohibited in any stream of the Commonwealth. This had the effect of accelerating research in a variety of areas, although treatment methods still retained primary interest. When a feasibility study of deep-well disposal was proposed to the Pennsylvania Dept. of Mines and Mineral Industries, the Coal Research Board (CRB) approved it. This paper summarizes the efforts on this project. Acid mine water is a chemically complex liquid. having no definite quantitative relationship among its constituents. However, it is the iron disulfide (FeS2) associated with practically all coal seams that produces the objectionable products present in acid mine water when combined with air and water. The principal contaminants are sulfuric acid (H2SO,) and ferric hydroxide (Fe(OH)2. Ferric hydroxide is a rust-colored gelatinous precipitate that coats stream bottoms and destroys aquatic life. However, other ions and bacteria are present in acid mine water in varying amounts.

Jan 1, 1971

By Charles Steed

The design of pillars in room and pillar operations is always a compromise between factor of safety and ore recovery. In actively mined and accessed areas the stability of pillars must be sufficient to support the roof, providing safe working conditions for men and equipment, while optimizing ore recovery. As a reserve is mined out, and if conditions are favourable, pillars are often removed to increase recovery. Considerations for pillar removal include value of the ore, the effect on immediate and overall mine stability and the safety of the mining operations as well as the consequence of disruption of overlying strata and surface infrastructure as the support of the pillars are removed. Many parameters influence pillar strength and the contribution of the pillar to ground support. These include seam height, seam depth, seam inclination, room span, quality of rock, time, etc.. Empirical, analytical and numerical modeling methods are commonly used to optimize pillar sizing and placement and predict influence of pillar extraction or reduction on ground stability. Practical examples for pillar design and optimization in low seam gypsum mining operations and optimizing sequencing of pillar extraction in thick seam metal mining operations are outlined.

Jan 1, 2003

By John Lindsay

"Although diamond mining is a relative newcomer to the Canadian mining industry, with the first diamond mine coming on stream in 1998, Canada is already a significant producer of high quality diamonds. This paper will review diamond production trends and highlight some of the projects currently under development, which have the potential to enhance Canada’s role as a significant diamond producer.Diamond recovery plants generally incorporate well-established mineral processing and recovery techniques, with issues such as product security, cut-off sizes, and diamond preservation becoming important considerations when developing process flowsheets. A diamond processing plant must achieve three key objectives, namely:• Liberation of the diamonds from the host rock;• Separation of the heavy minerals, which include the diamonds, from the host rock;• Recovery of the diamonds from the heavy mineral concentrates.Processing technologies and equipment commonly utilized in diamond processing plants will be reviewed and some of the significant issues associated with each option briefly discussed.Typical process flowsheets will be presented.Finally, an overview of De Beers’ Victor diamond project, located in northern Ontario, will be provided. This potentially significant diamond producer is currently at a pre-feasibility stage of development.DIAMONDS IN CANADAWorld Diamond ProductionCommercial diamond mining commenced in earnest with the discovery of the Kimberley diamondfields in South Africa in the late 1800s, and this resulted in a dramatic increase in the supply of diamonds. As can be seen from figure 1, world diamond production, mainly from South Africa, Angola, Congo, and Namibia, remained relatively constant through the early 1900s until the development of the large Russian kimberlite pipes in the 1950s. Production increased again in the 1960s and 70s with the development of the Botswana mines, but the most significant increase in global production came from the Argyle mine in Australia, which came on stream in 1983 and produced a peak of almost 43 million carats in 1994, representing approximately 40% of the world market. Production from Argyle has since fallen-off as grades have declined and the strip ratio has increased with the deepening of the open pit."

Jan 1, 2003

By A. W. Khair

This paper deals with the design characteristics of cutting tools and the operating parameters these tools are usually subjected to. Eight types of cutting tools/bits with different geometrical shapes and sizes were tested in a linear cutting apparatus, utilizing concrete blocks. The objectives of these experiments were to study the performance of each type of bit, make qualitative assessment of each bit geometry and size and establish cutting parameters for efficient utilization of the tools. During the experiment required forces Fx, Fy, and Fz, cutting, penetrating and lateral forces respectively and audible and sub-audible noises were measured. In these experiments, the depth of cut was kept constant to 1.5 inch while the bit spacing was varied 1.5,2.25 and 3.0 inch (3.75,5.6 and 7.5cm respectively). The results of these experiments indicated that by optimum ratio of depth of cut to bit spacing, the cutting face will be cleaned with the least ridge/land remains between the bit groves, resulting in least specific energy consumption, more large and less fine product particles and substantial reduction of audible noise. The results of these experiments also showed that proper bit design not only decreased cutting energy consumption but also reduced audible noise.

Jan 1, 2001

By Wolfgang G. Brunner

The closing of the gap in the European waterway- net is one of the big and challenging traffic projects following the German reunification. The water canals in the North German plain connect the Rhine river, the border between Germany and France, with the Oder, the German border river to Poland. As early as in the 30's of the 19th century the planning and construction of a ship- lift and a canal bridge started, in order to close this last big gap in the system between the Mittelland Canal and the Elbe- Havel Canal near Magdeburg. This main waterway connects the West of Germany, known for its coal mines and steel mills, with the capital Berlin, and from there it goes on into Poland. The building activities started in 1934 but came to a complete stop in 1942 because of the war. The communist government in East Germany was not interested in continuing this huge project, including the ship lock Rothensee, the canal bridge crossing the river Elbe, the former border river between West and East Germany, and the lock Hohenwarthe due to lack of political backing along with low construction capacity.

Jan 1, 2000

By D Brooks, S Gunn, T Perkins, J Siliezar

Ernest Henry Mining (EHM) is a copper, gold and magnetite mining and processing operation located 38km north east of Cloncurry. The EHM ore body has an average grade of 0.9% copper (chalcopyrite), 0.5g/t gold and 22% magnetite.Open pit mining commenced in March 1998, but EHM transitioned to underground mining in December 2012, extending the life of operations beyond 2024. The underground mine currently produces up to 3Mt/year of ore, hauled up a decline by truck. This figure shall double in 2014 with the completion of a 1000m shaft. The EHM Concentrator has a nameplate capacity of 10Mt/year. In June 2011, Xstrata Copper acquired the Mount Margaret resource to supplement underground production and utilise the full capacity of the Concentrator. The Mount Margaret Mining (MMM) operation was established to develop the five deposits making up the resource by way of open pit mining.Copper concentrate is produced by the EHM Concentrator via grinding, flotation and dewatering circuits. The grinding circuit comprises a SAG and ball mill in a closed AB configuration. Flotation consists of a rougher train, regrind and three stages of cleaning, with the tail from the first stage reporting to the tailings thickener.The mineralogy of the MMM ores is complex, comprising fine textures of active pyrite, copper oxides, native copper, clay and secondary copper sulphides. This paper provides an overview of the metallurgical test work completed to forecast the performance of the MMM ores through the EHM Concentrator and identify flow sheet modifications for maximising copper recovery and producing a saleable concentrate. A discussion of the challenges experienced in the plant to date follows.CITATION:Gunn, S, Siliezar, J, Brooks, D and Perkins, T, 2013. Adapting the Ernest Henry Mining concentrator to process the Mount Margaret ores, in Proceedings MetPlant 2013 , pp 347-370 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 15, 2013

By Bruce Vandenberg, Andy Battfay, Don Lake, Steve Conway, Jeff Yorsz

"High-speed motion pictures are an invaluable resource for blasting analysis. Whether processed by the human eye or a computer, this imagery can provide important insight into a blast and its effects.While certainly popular, traditional high-speed film cameras hamper this process. Instant feedback is not available since film requires developing and, relevant in the case of automated analysis, film isnot immediately compatible with a computer. With these facts in mind, a new high-speed video camera system, the SVCSOO, has been developed. The SVC500 combines the capabilities of a high-speed film camera, the convenience of a solid-state digital video camcorder, and the computing power of a ‘486 PC to provide a complete, standalone platform for high-speed image acquisition and analysis. This paper will describe the design, features, and use of the SVCSOO andcompare these with the analogous aspects of film cameras."

Jan 1, 1994

By Christopher J. Bise

INTRODUCTION The control of nuisance water in a mine is extremely important; left uncontrolled, nuisance water can have a severe effect on haulage, ventilation, production, and the health and safety of miners. To control water in mines, a four-step process is followed: (1) prevention, (2) collection, (3) transportation, and (4) treatment. This chapter will be devoted to the collection and transportation of mine water because prevention is usually dictated by pre-mining conditions and initial planning, while treatment is variable and highly site specific. A mine drainage system is nothing more than a collection of gathering points (sumps), machines that impart energy to the fluid (pumps), transportation ducts (pipes), and control devices (fittings, valves, etc.). A pump does not pull the fluid up the suction pipe; atmospheric or external pressure pushes the liquid up the suction pipe to the pump. All references in this chapter will be to centrifugal pumps, due to their popularity for mine drainage. PUMP CHARACTERISTIC CURVES The performance of a pump is plotted on a graph as an indication of its characteristic. To develop the data points, a test facility similar to that shown in Fig. 1 is established. The calibrated Venturi meter is used to measure quantity, the Bourdon gage measures pressure, and the wattmeter measures power input. Various discharge pressures are obtained by throttling with a gate valve in the discharge pipe. Quantity and power are measured at each of these pressure levels, giving the necessary data for plotting the characteristic curves. Fig. 2 shows a typical characteristic curve for a centrifugal pump. Notice that pressure is measured as so many feet of vertical water column above the outlet level, or head. Knowing the quantity (in gallons per minute), head (in feet), and power input (brake horsepower), the pump's efficiency can be plotted based upon the following relationship:

Jan 1, 1986

By S. Noll

Ventilation is an essential part of any underground mining operation. It provides fresh air for workers and machinery, keeps up an adequate mine climate and dilutes and dissipates noxious gases. Possible changes in the economic environment for mining in the future, e.g. increasing energy costs, will necessitate optimization of distribution of airflow within most mines. This paper discusses the scientific set-up for measurements as well as the behavior and influence of parameters of ventilation according to airflow distribution under consideration of technically possible set-ups of mine fans. This study was done in an underground mine with a flat seam room and pillar mining method.

Feb 27, 2013

By Yoginder P. Chugh

Subsidence may be observed above partial extraction shallow room-and-pillar mines where the coal seam(s) is associated with weak and thick claystone in the floor. This paper presents results of subsidence studies at such a mine. During the 26-month study period, a time dependent subsidence causing a maximum vertical movement of 50 mn was observed. After a subsidence rate of 6.0-6.5 m/month for the first two months after development of mine workings, the rate decreased to 0.8-0.9 mm/month after 17 months. However, presumably due to settlement of barrier pillars, it increased therafter to 1.7 mm/month for the next 9 months. Angle of draw, based on zero subsidence, was calculated to be about 29 degrees. Maximum tensile strain and compressive strain values observed were 0.040 pct and 0.039 pct respectively. A hypothesis was fomlated to correlate surface subsidence movements with observed underground movments. The data collected to date fits reasonably well within the formulated hypothesis.

Jan 1, 1989

The 106th Annual General Meeting of The South African Institute of Mining and Metallurgy was held in the J.C. Lemmer Auditorium, SA National Museum of Military History, 22 Erlswold Way, Saxonwold, Johannesburg on Wednesday, 13th August, 2003. Welcome The President extended a special welcome to the guests and representatives of our sister institutes and other associations, also to recipients of awards, senior members of industry, Honorary Life Fellows, Past-presidents, our Members and other guests, among them the following: Kevin Moxham, President, Association of Mine Resident Engineers Prof. Jay Barton, Vice President, The Geological Society of South Africa Dr Gus Muller, President, Institute of Certificated Mechanical and Electrical Engineers, South Africa Marius van Rooyen, President, Institute of Mine Surveyors of South Africa Benjamin Ngulube, Deputy Vice President, South African Institution of Electrical Engineers Dr Francois Malan, Chairman, South African Institute of Rock Engineering Dr Paul Jourdan, President, Mintek

Jan 1, 2003

By C De-Vitry

"The large Yandi channel iron deposit (CID) is located in the north-west of Western Australia and is currently mined via open pit methods. Drilling at Yandi is widely spaced and current estimates are mostly linear averages of the surrounding local samples. Linear estimates such as ordinary kriging (OK) based on block sizes that are significantly smaller than the dimensions of the drilling grid are less variable than the unknown reality (Armstrong and Champigny, 1989).Conditional simulation (CS) provides a series of plausible realisations that represent the actual grade variability at a small scale (eg 1 m + 1 m + 1 m). These simulations are very useful for a number of purposes, eg: optimising grade control, stockpiling and blending selection of optimal drill hole spacing assessing resource risk on contained tonnage and metal.At Yandi the major constituents of the ore (Fe, P2O5, SiO2, Al2O3 and LOI) are correlated to varying degrees. Independent CS of each assay variable will not reproduce these correlations. Reproducing the correlations (and the shape of scatterplots) is important if the simulations are used for the abovementioned purposes. This paper examines and compares various methods of CS that aim to reproduce the correlations between the assay variables.The CS methods evaluated in this paper are conditional co-simulation (CCS) using the linear model of co-regionalisation and two other, alternative multivariate simulation methods, which use min/max autocorrelation factors (MAF) or the stepwise conditional transform (SCT) to de-correlate assay variables before performing independent CS. It was found that CCS best reproduced the characteristics (histograms, variogram, scatterplots, etc) of the declustered drill hole data (Figure 1). Whilst simulation using MAF generally produced acceptable results, the method did not adequately reproduce the variance of the assay variables. The univariate statistics, histograms and experimental variograms were acceptable for simulations generated from the SCT. Bivariate statistics, cross-variograms and scatterplot reproduction for the SCT were unacceptable. The latter method produced inferior results because there were insufficient samples to obtain a reliable transform of the third assay variable in the transformation sequence.None of the abovementioned simulation methods provides good reproduction of all the scatterplots. This is due to the presence of clay pods, which cause some scatterplots to display two trends. These clay pods contain higher percentages of SiO2 and Al2O3 than the surrounding CID. The clay pods are generally smaller than the drill-grid dimensions. Thus their locations are typically unknown and they cannot be defined by manual interpretation, eg via wireframes. The locations of the clay pods were simulated via indicator CS. CCS was then performed separately for the clay pods and the CID. This significantly improved the reproduction of the correlation coefficients, the scatterplots and visually the simulation was more geologically realistic. Simulating the location of clay pods followed by CCS of assay variables is the recommended approach for simulation at the Yandi CID.CITATION:De-Vitry, C, 2013. Simulation of correlated assay variables - a case study from the Yandi Channel iron deposit, in Proceedings Iron Ore 2013, pp 137-148 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 12, 2013

By Paul Laframboise, Nigel MacDonald, Mike Hallewell, Robert Thorpe

"Galmoy Mine, owned by Arcon Mines Limited, has operated since 1997, and is one of three operating lead/zinc mines in Ireland. Changes in ore type starting in mid 2002 created challenges to metallurgical operations at Galmoy. This resulted in unacceptable lead and zinc flotation performance, which prompted initiation of a formal plant review and a subsequent stabilization programme. This involved a structured review of operational practices, development of a new Standard Operating Procedure (SOP) which in turn led to significant changes in process control equipment needs in conjunction with extension of zinc flotation cell residence time.This paper will describe the metallurgy of the Galmoy operation. Reasons for the poor metallurgy experienced in 2002 will be described, as well as the solutions identified to overcome these problems. By the second quarter of 2003, these solutions had been implemented and recoveries had risen to record levels.INTRODUCTIONGeneralGalmoy Concentrator is located in County Kilkenny (Refer to Figure 1 below) and was constructed during 1996 and commissioned in 1997.The concentrator at Galmoy had been designed initially to treat 650,000 tonnes per annum of primarily CW ore type. The main mineral of economic significance was sphalerite (Typically 10 to 11% Zn) with some minor galena (0.7%Pb) in a dolomite (Magnesium Carbonate) host rock.The only other competing sulphide mineral was pyrite (Circa 3 to 5% Fe in Mill Feed. This CW ore type predominated the first 6 years of production, but in August 2002, the ore mineralogy changed due to significantly higher levels of pyrite rich G ore body being blended in with CW ore."

Jan 1, 2005

[ ]

Jan 1, 2008

Several industrial-scale HydroFloat separators have recently been installed at Mosaic?s South Fort Meade beneficiation plant for the purpose of improving phosphate recovery and throughput capacity. This technology was implemented after numerous laboratory, bench-scale and on-site, pilot-scale test campaigns. The results from this detailed test work provided sufficient justification for the complete retrofit of the existing coarse and ultra-coarse flotation cells. Data indicate that the metallurgical results obtained with the full-scale separators are consistent with that obtained during both the bench- and pilot-scale evaluations. The benefits, theory of operation and commissioning of the equipment are also discussed.

Jan 1, 2007

The Effect of Mineral Liberation on the Floatabilities of Pyrite, Arsenopyrite and Arsenian Pyrite for Carlin Trend Ores

Sep 13, 2010

By Stephen C. Tadolini, Dennis R. Dolinar

The risk of injury caused by minor roof falls continues to increase in underground mining. Most ground control injuries result from small rock falls that occur in a supported area, but do not involve the failure of the support system. In the roof, these are the "skin failures" that occur between previously installed primary or secondary bolting systems. To minimize skin failures and the associated accidents, several devices were designed and tested in the laboratory to maximize stiffness, minimize material thickness and weight, and ease material storage and handling on roof bolting machines. The goal of this project was to design and evaluate devices that can be installed with traditional primary or secondary roof supports, and that are easy to handle/install under temporary or previously supported roof.

By Pfeifer H. C, Nicacio P. A D

Sinter has been used as part of the metallic charge in large-scale blast furnaces for many years with the well-known benefits in terms of productivity and fuel consumption. However, because of the high investment in a conventional sinter plant, small blast furnaces and the associated integrated mini steel plants have not taken the advantages of using sinter. Recently KTS Korf Tecnologia Siderurgica, a division of Mannesmann Demag Ltda in Brazil, has developed a mini sinter plant for which the investment is compatible with small blast furnaces. Consequently, it is of great interest to evaluate the economical impact of using sinter in such small-scale integrated steel plants. In order to compare two alternatives, ie 100 per cent ore and 70 per cent sinter in the blast furnace burden, mass and heat balances for the entire operation from sinter plant through the blast furnace and EOF-based melting shop, were performed to evaluate the final production cost of the liquid steel. It was found that, depending on the sinter feed price, substantial savings can be obtained with the use of sinter.

Jan 1, 1999

By Anthony B. Szwilski, Dalip Sarin, Richard D. Begley

This paper will present the results of an analysis of several abandoned coal mine projects and includes field data for over a dozen different reclamation projects recently completed in the state of West Virginia. The analysis was performed with the objective of summarizing and or classification of the environmental consequences with reference to the characteristics of the mining facilities (surface, underground, etc.). The analysis also addressed the itemized cost of remediation with respect to procedures, environmental concerns and time. The results of the analysis are that each abandoned coal mine site in West Virginia have/had many unique features and in most cases include a combination of environmental concerns that complicate comparisons. The study also revealed that the abandoned mine land program for mines abandoned prior to 1977, that is being financed by a tax on the production of coal, has produced many benefits for the state of West Virginia. This grant program administered by the Office of Surface Mining, has resulted in a high quality methodology of remediation that has been successful for many years in greatly minimizing and/or eliminating environmental concerns from abandoned coal mines.

Feb 24, 1997

By W. M. Pytel

The applicability of the beam theory in analysis of roof- pillar-weak floor interaction in partial extraction room-and-pillar mining is presented. The mine structure is modeled as an equivalent multi-indeterminate overburden elastic beam supported by elasto-plastic pillars; resting on a viscoelastic layer of immediate weak floor strata underlain by a competent rock mass. The developed analytical model was initially utilized to conduct sensitivity analyses of different variables affecting the mining system, such as the deformability of coal and weak floor strata, thickness of weak floor strata, number of pillars in a panel, width of pillars, width of panel etc. These analyses were then extended to three overburden strata - coal pillar - floor strata lithologies typical of active coal mining areas in Illinois.

Jan 1, 1989