Search Documents

By Doug Anderson

Blast vibration seismograms are generally collected strictly for compliance with regulations. The peak levels (including dominant frequency) are typically all that are looked at. However, these records contain a lot more information about how a blast has performed. The seismogram is actually a record of explosive energy that was not used in fragmenting rock. The trick is to determine how to extract information that would be useful in analyzing blast performance.

Jan 1, 2013

By Ernesto Zelaya P

En el Perú, muchas de las empresas mineras se desarrollaron por la configuración de sus yacimientos explotados. Sin embargo, también se generaron limitaciones y restricciones en el transporte, extracción de mineral y/o desmonte dentro de las operaciones mineras. En este sentido, el presente texto señala una forma de inversión a través de un sistema de izaje, donde se realice un costo menos y una mayor productividad en la Unidad Minera Animón – EACH S. A. C. (Pique Jacob Timmers) y en la Unidad Minera Andaychagua – U. P. Yauli (Pique Roberto Letts) que son partes integrantes de las operaciones mineras de Volcan Compañía Minera S. A. A

Sep 12, 2011

By M. Yavuz, M. Aksoy, G. Once, M. Iphar

This paper is concerned with a study on the floor heaving in the transport road of the GLI Omerler Colliery in Tuncbilek-Turkey. This gallery has been opened at the depth of 200 m through the formation of marl in 4.6 m width and 3.5 m height in cross section. Floor heaving occurred up to 70 cm in height in maximum and caused severe problems in railway and band-conveyor transportation in the main road. In addition; after the current panel mined out, the shield support units could not be transferred to the new panel because of the deformation of roadway cross-section. The I-profile steel arch supports also sank into the weak floor rock. This situation has been studied by numerical analysis using the FLAC3Dfinite difference program in order to investigate the rock mass behaviour around the opening. The obtained outputs of the numerical model have showed consistency with the amount of floor heaving in the gallery at 200 m depth. A new gallery has been driven at the depth of 115 m and M4 longwall panel has just been taken to production. So as not to encounter with the same problems at 200 m depth, especially longwall face moving problem, various numerical models have been studied in order to keep the floor heaving in the acceptable limits required to move shield support units. Keywords: Floor heave, Numerical modelling, FLAC3D, Failure criteria, RocLab

Jan 1, 2003

By F F. Pitard

The comparison between J Visman and C O Ingamells’ works with P M Gy’s works has been the object of intense debates in the past. Such negative debates inevitably resulted in a loss of many good opportunities. The author’s long experience in applying works of these three authors led to the pragmatic conclusion that it is relatively easy to integrate everything Visman and Ingamells created into the Theory of Sampling; therefore, it is suggested that the compatibility has been vastly overlooked, and a correction for such anomaly is recommended. It is important to emphasise that Visman and Ingamells works may be beneficial and provide relevant, harmonious additions in some areas, and ultimately offer attractive possibilities to sampling practitioners. Such additions may enhance our capabilities to predict sampling difficulties by using a stronger strategy and to design better sampling experiments that would allow us to further understand the heterogeneity of minor constituents, and especially trace constituents. Basically, the suggested integration is essential for sampling trace constituents in the environment, in food, in chemicals and in the pharmaceutical industries.CITATION:Pitard, F F, 2017. Integration of Visman and Ingamells’ works into the Theory of Sampling – a necessity to expand possibilities in sampling practices, in Proceedings Eighth World Conference on Sampling and Blending , pp 55–62 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017

The published liquidus data on the Pb-PbS system have been correlated on the basis of one-coefficient Margules equations. Thermodynamic properties of the components of this system have been obtained, and it has also been found that the calculated miscibility gap of this system exists over a very narrow range of temperature (1041 to 1058°C).

Jan 1, 1972

By Charles Deacon

The mining industry is constantly taking greater cognisance of their operating costs as a strategy to counter the effects of falling commodity prices. As a result, optimal operating efficiency is more important than ever. One such operation is that of blasting. Considering the relative increasing costs of explosives and accessories it is desirable to optimise the number of blast-holes fired by maximising their individual output. This achievement may now only be possible following the advent of higher technologies in the form of modified explosives and electronic detonators. This paper reviews and introduces some techniques of blast monitoring, types of operations where each is most suited, resulting modifications to blast designs, and identifies some pitfalls to watch out for when analysing the results.

Jan 1, 2000

By David Oyler, Craig Compton

The The National Institute for Occupational Safety and Health (NIOSH) Pittsburgh Research Laboratory (PRL) is continuing to investigate the behavior of fully grouted roof bolts in the weak roof rock of the Safety Research Coal Mine (SRCM). This paper describes the results of three studies: • A series of 24 pull tests of bolts installed fully grouted and overcored to leave 12 inches of grouted bolt. The tests compared the pull-out performance of offset-head roof bolts with that of standard 5/8-inch bolts; • A second series of 24 tests that compared the pull-out loads obtained by bolts installed with 1 ft of resin (a Short Encapsulation Pull Test or SEPT) to that of fully grouted bolts overcored to leave only 12 inches of grouted bolt, and; • An investigation into the pressures generated during the installation of fully grouted resin bolts. All of the bolts installed and pulled were overcored and removed from the roof after the pull tests to allow inspection of the resin. The first study found that there was no significant difference in pullout load between the offset-head bolts and the standard bolts. The second study, comparing the SEPT bolts and the partially-overcored fully grouted bolts, indicated that SEPT can significantly underestimate bolt anchorage grip factor, suggesting that the SEPT is a conservative measure of actual bolt performance. Significant loss of resin to cracks in the roof was observed in the bolts overcored in the SRCM. The third study explored one possible explanation for the resin loss, high pressures generated during bolt installation. These tests employed bolts installed in strain gauged steel tubes. The results confirmed that significant pressures (greater than 4,000 psi) can be generated during bolt installation. The results of the pressure tests, combined with the observations of resin loss in bolts installed in the SRCM, suggest that under some circumstances resin loss and under-encapsulation could take place and lead to degraded bolt performance. Glove fingering was observed in all recovered bolts to various degrees. The limited comparative data suggested that the effect of glove fingering ranged from slight to moderate. Complete mixing of the resin was observed on all of the 40 bolts recovered (28 fully grouted and 12 SEPT). Australian and U.S. resins were compared and the Australian resins were observed to have much smaller catalyst compartment areas and lower resin viscosities. These differences are suggested as potential explanations for occasional resin mixing problems noted in Australian resin bolt installations.

By Dayle Denton, Lloyd Buckingham, Kenneth G. Thomas, Jacques McMullen

"The dry grinding and leaching circuits of Barrick Gold’s new Roasting Facility at Goldstrike Mine in Nevada, USA incorporate well proven technologies in a unique combination. During the design of the plant, every effort was made to utilize the best available technologies from the perspective of capital, environment and operating costs.Crushing is a two stage process using gyratory and cone crusher. Ore is stockpiled and then reclaimed to two parallel dry grinding mills. The double rotator dry grinding mills include a drying chamber, coarse and fine compartments and utilize a gearless motor drive (GMD) or “wrap-around”. In-circuit product transfer is accomplished with air slides and bucket elevators. Finished product separation is performed by both static and dynamic classifiers with the final product captured in baghouses. Recycle of unfinished product utilizes cascade chutes.The final ground product reports to two 2000 ton roaster feed silos. The two-stage oxygen flu-solids roasters with their associated gas train are the subject of a separate paper.The cyanide leach circuit is a standard carbon in leach system with circular swept screens for interstage carbon retention. The loaded carbon is sent to the existing Goldstrike autoclave plant for stripping and regeneration. Tails, after cyanide destruction, are deposited in the existing tailings dam with tails from the autoclave facility.Throughout the circuit, Clean Plant Design criteria were used to assure environmental compliance, ambiental acceptability and ensure worker health and safety. The commissioning and operation of the double rotator grinding technology has been very successful at Barrick Goldstrike."

Jan 1, 2001

By A. Adu-Acheampong

Stope instability at Ashanti Goldfields Company Ltd. (AGC) is a major concern. Using information from field mapping, major discontinuity sets were defined, Rock Quality Designation (RQD) was determined. The stability of wedges in the stope walls was assessed using the commercially available computer program UNWEDGE(Rock Science, 1992). Analytical results indicate that the presence of graphite infilling in joints contributes to instability, while steeply dipping joints control wedge slabbing and wedge toppling in the hanging wall. Stable stope widths and dimensions were determined to range from8.1 to 30 meters (m).

Jan 1, 2003

By J. P. Neumann, L. Raymond

At temperatures near 1000°C, only the (112) (111) slip systems are operatire in tungsten. Therefore, the substructure introduced into the billet upon rleforming a single crystal by rolling at 1000 "C can be controlled by proper selection 01. processing ral'iubles. Using a reduction of 10 pct pel- pass, the (001)[110] and the (110)[001] crystals will deform by duplex slip rip to a 50 pet reduction in thickuess. These rolled single-crystal sheels are characlerized by anisotropic hardening, retention of ductility with warm working, lattice bending which is related to the conlacl (angle, and macroscopic dimensional changecs in the length bid not the width of the billet. When several slip systems become operative, a greater degree of work hardening is itztvoducetl into the crystal. This rolling- condition is characlerized by isotropic hardening, loss of ductilily with warm working, complex lattice distortions, and macro-scopic dimensional changes in both the length rind Width of the billel. IN tungsten, the {1 10}(111) slip systems are operative below room temperature,' while above 700°C only the {112{ (111) slip systems are observed.2,3 In the transition region, i.e., room temperature. both systems appear. It is the purpose of this investigation to show that tungsten single crystals deformed by rolling at a temperature where only one slip system is operative generate dislocation substructure which depends on the crystal orientation. For a specific crystal orientation. the resulting dislocation substructure can be further influenced by modifying the rolling procedure. Crystals oriented for multiple slip display less substructural sensi- tivity to modifications in processing techniques than do single crystals oriented for duplex slip. Under simple slip modes of deformation, very little work hardening is introduced into a rolled single-crystal sheet. Mechanical properties such as room-temperature strength. ductility, and hardness are used to confirm the existence of the different work-hardened conditions generated within the crystal by modified warm-rolling techniques. EXPERIMENTAL PROCEDURE Material. Single-crystal billets of four different crystal orientations. grown by the Arc-Verneuil technique. were ground to a size of 0.25 by 0.375 by 3 in. In terms of their rolling plane and rolling direction, the billets had the following orientations: (1101 [001 ] (110) [110] (001) [110] (001) [100] The actual orientation of all crystals was within 5 deg of the ideal orientations. The typical impurity content of the crystals is given in Table I. Polishing and Etching. Polishing was done elec-trolytically in a 20 g per liter aqueous solution of NaOH at approximately 10 v. It was established by the Laue back-reflection X-ray technique that the surface damage due to grinding and cutting operations with a diamond wheel did not exceed 0.001 in. Therefore after each cutting or grinding operation at least 0.002 in. was removed electrolytically from the surface in order to eliminate surface effects. By lowering the voltage to 3 v, subgrain boundaries and individual dislocations are identified in agreement with Berlec 4 where the etch-pit traces on a cubic plane form a square. The etching time was about 5 sec at room temperature. Rolling. Rolling was carried out on a Loma 2-high mill (Model 600). The peripheral velocity of the 6-in.-diameter rolls was 500 in. per min, with the surface temperature of the rolls about 400° to 450° C The billets were heated before each pass for 30 min in argon to 1000 C. Oxidation of the crystals during rolling in air resulted in a thin layer of greenish-yellow WO 3 This oxide was removed after each pass by immersing the crystals for a few minutes in a boiling NaOH solution. Prior to the initial rolling pass, a surface layer of 0.001 in. was removed by polishing. The crystals were then annealed in vacuum (10-4 torr) at 2400 C for 30 min. All crystals were rolled in the same direction; i.e., the same end was always introduced into the rolls. The rolling program was conducted in

Jan 1, 1965

By J. C. Vreugdenburg, B. A. Dippenaar, J. Muller, T. L. de Vries

Iron ore fines are agglomerated to produce sinter, which is an important feed material for blast furnaces worldwide. A model of the iron ore sintering process has been developed with the objective of being representative of the sinter pot test, the standard laboratory process in which the behaviour of specific sinter feed mixtures is evaluated. The model aims to predict sinter quality, including chemical quality and physical strength, as well as key sinter process performance parameters such as production rate and fuel consumption rate. The model uses the finite difference method (FDM) to solve heat and mass distributions within the sinter pot over the height and time dimensions. This model can further be used for establishing empirical relationships between modelled parameters and measured sinter properties. Inputs into the model include the feed material physical properties, chemical compositions, and boundary conditions. Submodels describe relationships between applied pressure differential and gas flow rate through the bed of granulated fine ore particles, combustion of carbonaceous material, calcination of fluxes, evaporation and condensation of water, and melting and solidification. The model was applied to typical sinter test conditions to illustrate the results predicted, and to test sensitivities to parameters such as feed void fraction, feed coke percentage, and the fraction of combustion heat transferred to the gas phase. A model validation and improvement study should follow, ensuring sinter test results are free from experimental errors by conducting repeated tests.

Jan 1, 2015

By W. W. Krech, T. E. Perkins

As fractures are propagated through rocks, energy is absorbed near the extending crack tip. Apparent surface energies for several rocks have been measured by cleavage under dynamic con-ditions. At nominal crack velocities from 0.5 to 500 in (min, measurements showed that fractures propagated in discrete jumps. Calculated surface energies and moduli were relatively insensitive to nominal rate of cleavage. in another set of experiments, rocks were cleaved under high confining stresses. The rocks were submerged in low leak-off fluids which formed a filter cake on the freshly cleaved surfaces (similar to the hydraulic lracturing process). Apparent surface energies were increased substantially as the surrounding fluid pressure was increased. Moduli in bending increased significantly upon application of the first 1,000 psi but were insensitive to stress level at greater pressures. INTRODUCTION For almost 20 years, hydraulic fracturing processes have been utilized effectively to stimulate oil and gas wells. During this period, some process improvements have resulted from studies of fracture orientation, mechanics of fracturing, areas generated, conductivities of cracks, etc. Yet many questions remain concerning the conditions and pressures needed during fracture propagation. In this paper we will report additional studies of the mechanics of fracture extension. It was shown previously3 that large rock samples could be cleaved under controlled conditions so as to measure the apparent surface energy (that amount of energy absorbed per unit area of new surface created). In this paper we consider the effects of two additional factors on surface energies, viz.: (1) effect of cleavage rate and (2) effect of confining stress level. THEORY Cleavage experiments were conducted on rock samples similar to that illustrated in Fig. 1. Blocks of rock several inches wide, 2- to 3-in. thick, and up to 3 ft in length were grooved longitudinally with shallow guide slots. A crack was initiated and allowed to extend along the web as the top of the rock specimen was pulled (or pushed) apart. Auxiliary equipment permits the measurement of (1) force applied at the top, (2) separation at the top and (3) crack length. (Further experimental details will be given in the next section.) The rock beams created by the crack are considered ton be cantilever beams. The deflection (or separation of the rock beams) at any point is calculated 4,5 by the beam Eq. 1.

Jan 1, 1967

By Reinhold Schnell, Piers Wendlandt, Nathan Rouse

Drilling and blasting are key components of every hard-rock (i.e.,metal/nonmetal/coal) mining operation. Well-executed and maintained drilling and blasting can have a major positive impact on the overall success of such operations. This case study presents the implementation of a new drill and blast engineer position and systematic improvement of the drill and blast operations at a surface metal mine. The findings of and lessons learned from this case study can be applied toother mine operations to improve safety, production, efficiency, and cost savings. Focus areas for the project included refined communications, operational practices and procedures, planning, designing, and data collection and analysis. This case study showed improved efficiency in communication and planning among the engineers, operations team, and contractor groups over the course of the project. An increased awareness of long-term plans and needs for the drills and blasters reduced or eliminated existing delays. Test blasts that implemented new drill and blast designs and updated operational practices and procedures were tested to streamline the process. Constraints regarding explosive product shipments, geological considerations, and a uniform powder factor provided the basis for new blast designs.

By William R. Yernberg

The 2002 Arizona Conference was held Dec. 8 and 9, 2002, at the Doubletree Hotel at Reid Park in Tucson. The annual conference is organized by the Arizona Conference Board of Directors, which represents SME sections in Arizona and adjacent areas. The conference provides an opportunity for individuals and corporations associated with mining in the region to get together once each year to discuss the status of the industry. The meeting featured a keynote address, a distinguished lecture and about 30 technical papers. As was the case at the 2001 meeting, the economy, the price of copper and foreign competition continue to be the hot topics of discussion among the attendees. The domestic copper industry still faces challenges due to low copper prices dictated by the world market and because of a weakened domestic economy. There continues to be concern about the Arizona region’s copper industry in light of the mergers, downsizing and shutdowns that have occurred during the past several years.

Jan 1, 2003

Threshold blasting involves the use of small amounts of high explosive to break and fragment hard rock without having to evacuate mining personnel. The method is easily assimilated and effective in rockbreaking, but requires rigid control on drilling, charging and timing. Current underground trials are aimed at fine-tuning the amount of explosive energy and blast hole geometry to allow the firing of multiple sets of shot holes in a continuous manner. Through correct procedures, the after-blast fumes, dust and fly rock can be contained so as to provide a safe working environment. Threshold blasting hugely reduces the volumes of explosives used in mining and brings to maturity the potential of the process begun by Alfred Nobel when he introduced nitroglycerine, and later dynamite, to mining. Its key contribution is its enabling of continuous mining operations with well understood and relatively low cost technologies. The use of batch blasting, employing large burdens holds the greatest potential for delivering high flow rates of ore at minimal cost. There is good potential for rapid evolution of the concept.

Jan 1, 2002

By Noel C. Joughin

In making judgements on tolerable levels of risk in industry, and in all spheres of life, it needs to be understood that every action gives rise to risk. Without risk, nothing can be done. Without risk, no economy could be advanced. There is a strong tendency to emphasize the risk at work, but persons who are not working are exposed to a different set of risks. Often persons who are not working face greater risks than persons who are working. Simply, in being alive, one is exposed to the risk of an accident, the risk of contracting a disease, and an extremely diverse variety of other risks. According to the Health and Safety Executive of the UK, it is not possible to have a state of zero risk, because ?a state of zero risk does not exist?. Because zero risk is a physical impossibility, it is not possible to design for a state of zero risk in all engineering design. While the strategic target of achieving zero risk is laudable it does not provide any practical guidance to engineers as to what acceptable limits of risk should be. This causes a significant and real problem in the design for and the management of risk. Without meaningful guidelines, engineers, managers and the authorities often find themselves in disagreement. Thus, it has become essential to establish criteria for tolerable levels of risk and unacceptable levels of risk in order to design and manage engineering systems properly.

Jan 1, 2011

Publications on hard rock tunnel support design in the South African mining industry have originated primarily from the goldmines during the past 50 years. Little has been published to date on the platinum and chrome mines of the Bushveld Complex. This paper covers the search for a suitable design methodology for off-reef tunnels at Impala Platinum Mine, situated on the Western Lobe of the Bushveld Complex. The fall of ground accident statistics for off-reef excavations of the mine are presented and the available rock mass quality evaluation systems are reviewed. The Q-Tunnelling Quality Index (or Q-Index) is selected because it assesses the important driving factors behind falls of ground at Impala. Two off-reef excavations are evaluated using the Q-Index, and it is shown that minor modifications are required for implementation at Impala. It will take some time before support design throughout the mine is based on the outcome of proper geotechnical investigations based on the Q-Index. Widespread implementation of such support designs should help to solve the fall of ground problem in off-reef excavations while at the same time reducing support costs.

Jan 1, 2002

By R. P. Singh

A mine fire model gallery has been designed and constructed on the premises of the Central Mining Research Institute, Dhanbad, India to perform systematic in-depth studies on various aspects of mine fires. The gallery is 65.5 m long and 5.86 m2in cross-section and it is divided into firing and non-firing zones. It is equipped with a computer-aided online telemonitoring system that has 130 sensors, two data loggers and computer peripherals for continuous recording of various fire parameters. A fan to generate airflow through the gallery has been installed at its end. Two sliding doors and one rolling shutter were also provided for sealing and regulation of airflow. Two sets of experiments have been carried out in the model gallery maintaining air velocity of 1 and 1.5 m/s through it. In the experiments, the inner sides of the firing zone, 22 m in length, were lined with a thin layer (8?10 cm thick) of coal slabs. Two fire suppression techniques viz. flushing of liquid nitrogen (LN2) and infusion of high pressure high stability (HPHS) nitrogen foam were tried to quantify their effectiveness under dynamic fire conditions. The paper addresses important design features of the gallery, its instrumentation system, the experimental procedure adopted and important findings from the experiments. It has been observed that the intensity of the fire was very high after one hour of its initiation and continued for 3?4 hours. During the period, frequent backlash with smoke and flame was noticed. The efficacy of the fire suppression techniques has been assessed interms of reduction in temperature, generation rate of CO2and CO, and heat release rate. The study reveals that high pressure high stability (HPHS) nitrogen foam is more effective in controlling open fires than liquid nitrogen is. Keywords: Model gallery, telemonitoring system, velocity, temperature, pressure, gas concentration, intensity, liquid nitrogen, high pressure high stability nitrogen foam.

Jan 1, 2004

By B B. Beamish

Long-hole directional drilling for in-seam exploration was introduced to New Zealand at Huntly West Mine in 1989. Following the success of this initial drilling program the Coal Corporation of New Zealand (CoaICorp) purchased its own drilling equipment and proceeded to adopt the technique with in-housetraining. From July 1991 to September 1992 a total of 15 455 metres was drilled at Huntly West Mine. During this period several modifications were made to the drilling technology to suit the ground conditions. The resulting interpretations of the drill information enabled reliable seam definition to be incorporated in mine planning. Since January 1993, the technique has been transferred to the Huntly East Mine to assist with seam definition for the planned development westwards under the Waikato River. The benefits of this drilling technique to coal mine planning are now well documented in Australia and New Zealand as well as other overseas countries. The possibilities of adapting the long-hole drilling technique to hard rock applications has been illustrated recently with successful cross-measure drilling at Huntly East Mine.

Jan 1, 1993

By John R. Eckel

A Iaboratory drilling rig has been devised and placed in operation which permits the application of hydrostatic, terrastatic, and formation pore pressures to a rock sample for drilling under controlled conditions. Calibrated rests of this equipment in-dicate qualitative agreerment with field results on the effect of weight on bit, rotary speed, and rate of circ~~lation on drilling rate. Tests under pressure, using water and air as the drilling fluids, indicate that when drilling saturated limestone samples, a pressure differential between hydrostatic and formation pressure is the only pressure which affects drilling rate. A differential in either direction causes a reduction in rate, but the same diflerential from the wellbore into the formation causes the greater reduction. Also, in lime.stone, air favorably affected drilling rote only when compared to water at high hydrostatic pressurre, all other conditions remaining constant. Large increases in drilling rate with air could be obtained in the laboratory only while drilling a shale, which offered a limited permeability to nitrogen and which could be drilled with a differential from the formation into the wellbore. In general, the magnitude of the changes due to the pressure effect were small compared to changes in drilling rate obtainable by changing either bit weight or rotary speed. INTRODUCTION In the course of Humble's drilling research program, the desirability of investigating several factors which lend themselves to laboratory rather than field study became obvious. Principal reasons for this are the expense involved in field studies and the difficulty of exercising the required degree of control. Of primary importance are investigations of the effect of fluid pressure on rock rate, the effect of pressure on rock drillability, and a study of the fundamental mechanics of rock failure and chip generation. Several years ago some work in the laboratory on the effect of mud properties on drilling rate was re- ported to the API', but the completion of this work and the investigation of the other variables affecting drilling rate required equipment somewhat more elaborate than that used on these earlier tests. This equipment has been assembled to form Humble's Drilling Engineering laboratory. To date only the effect of pressure on rock drillability while using water and air has been investigated, and this work is not yet complete. Facilities are available to investigate the effect of fluid properties on rate of penetration, and information is being assembled on a current basis on the mechanics of drilling. The sequence of presentation in this progress report is somewhat different from that in which the data were obtained since the order of ex-