Search Documents

By R. K. McLimans, C. Knudsen, S. Bernstein, D. Frei

Computer Controlled Scanning Electron Microscopy (CCSEM) is used to analyze indivdual mineral fractions in heavy mineral sands. CCSEM is a fully automated particle analysis technique for the determination of physical and chemical properties of a large number of individual particles. CCSEM enables the precise and accurate determination of the modal abundances of individual mineral fractions (e.g. ilmenite, rutile, zircon, or garnet), their average chemical composition (and compositional variation), as well as their physical properties such as size (e.g. diameter and perimeter length) and shape (aspect ratio and circularity). A unique sample preparation procedure is used to produce representative polished sections from cylinders of raw sand samples such that thousands of grains are present in a polished cross section, but grains are not touching. The combination of this sample preparation technique with CCSEM enables the fully automated analysis of individual grains without the application of de-agglomeration or erosion steps to separate touching particles. Hence, CCSEM yields information representative of the entire area of analyzed grains without systematic bias due to neglect of rim areas by de-agglomeration or erosion steps. Therefore, the resulting data are determined with high accuracy, precision and statistical validity. Because the sample preparation is relatively straightforward, using raw sand samples, and all chemical and physical properties are determined in one analytical session per sample, CCSEM is a powerful cost and time efficient tool for characterizing chemical and physical properties of minerals in heavy mineral sand deposits.

Jan 1, 2005

By S. Vivek

An atomic force microscope (AFM) was used to measure the surface forces between silica surfaces immersed in solutions of hydrolysable cations and/or sodium oleate. Hydrophobic forces were observed at the pH range where the concentration of the singly-charged hydroxo-complexes (CaOH+ or MgOH+) in solution is the highest. In the absence of oleate, the adsorption of the hydroxo-complexes was indicated by the disappearance of the repulsive hydration force. These results suggest that the hydrolysable cations adsorb on silica as singly-charged hydroxo-complexes. Based on the results obtained in the present work, a model for the adsorption of hydrolysable cations has been developed.

Jan 1, 2009

By R. D. Short

Environmental regulations for noise and air pollution are directly affecting the type of equipment and construction techniques being utilized for pile driving construction using diesel hammers in California and elsewhere. Consequently, the cost of construction is increasing and in some cases, the use of diesel pile hammers has been prohibited. Based on the trend in California and elsewhere in the world, environmental constraints are spreading and becoming more restrictive. The City of Tokyo, Japan, for example has banned the use of diesel hammers. Environmental restrictions on diesel hammers can be satisfied by using modern hammers, clean burning fuels, synthetic lubricants and pre-excavation techniques.

Jan 1, 1989

By Janet A. Flinn, David G. Fileccia

Machine guidance and control systems have become more pervasive in the mining industry in recent years but not always from mining-experienced providers. Dozers, motor graders, scrapers, excavators, shovels, draglines, drills and haul trucks are just a few examples of the types of heavy machinery now equipped with global positioning system (GPS)-aided guidance systems. While equipment manufacturers are offering their own software, many only supply solutions for the machines they produce. The proliferation of GPS equipment manufacturers entering the machine guidance and control arena has resulted in a multitude of makes and models of GPS receivers. Some of these companies also produce their own guidance software. But they usually just specialize in a narrow range of heavy machinery. So customers are forced to use multiple systems and face new challenges in implementation, training, reporting and inter-system communication.

Jan 1, 2006

By H. E. Biber

DURING the production of tin plate a thin layer of FeSn2, is formed at the interface between the steel sheet and the protective tin coating. Because excessive amounts of this alloy layer are undesirable, the kinetics of its formation is a subject of interest in the tin-plate industry. A recent study of this subject at our laboratory uncovered a relationship which should be of general interest to anyone studying kinetics of reactions in metallic systems. It had been previously concluded that, at any given temperature in the range 175" to 330°C, the Fe-Sn alloy layer would have a parabolic growth rate.1,2 However, our studies showed that this rule apparently holds only when the tin plate is heated very slowly to the "reaction" temperature; when the tin plate is rapidly heated, considerably different growth rates occur. An example of this effect of heating rate on growth behavior is contained in the accompanying results of alloy-layer growth measurements at 240°C in oil baths stirred at 10,500, 1800, and 0 rpm. The heating curves for these three conditions are given in Fig. 1, and the growth data are presented in Fig. 2. With the rapid heating rate, provided by the stirring at 10,500 rpm, the alloy layer had three distinct stages of growth. In the initial stage, which persisted well beyond the time required to heat the tin plate to bath temperature, the alloy layer formed very rapidly. The growth followed a rate law of the form w = ktn where n > 1. This initial stage was followed by a growth-retardation stage of about 50-sec duration in which little additional alloy was formed. In the third stage the growth again followed a rate law of the form w = ktn, but here « =0.3. With the intermediate heating rate provided by stirring at 1800 rpm, the three-stage nature was less pronounced and the slope of the third stage increased (i.e., n > 0.3). With the slow heating rate provided by the unstirred oil bath, the alloy layer grew in two stages. The initial rapid-growth stage persisted only until the specimen was heated to bath temperature, no growth retardation was observed, and the slope of the main portion of the plotted data was greater than in the stirred baths, having a value of almost 0.5. Similar results were obtained for other bath temperatures in the range 200" to 300°C. This effect of heating rate on growth behavior may be due to changes in the rate of nucleation of FeSn, crystallites. The iron and tin are in contact from the onset of heating. Thus the initial formation of FeSn, occurs not at the "reaction" temperature but rather while the tin plate is being heated to that temperature. Because nucleation is in general temperature-dependent, different heating rates could cause different over-all nucleation rates, which in turn could cause different growth behaviors. A more detailed discussion of the growth of Fe-Sn alloy layer and the effect of heating rate will be published shortly.

Jan 1, 1965

By John H. Hild

"INTRODUCTION Alunite occurs within a radius of 10 miles of Marysvale, Piute County, Utah, in veins and as replacements of igneous rocks. A number of each type of deposit was explored by the Bureau of Mines, in cooperation with the Geological Survey, under the Strategic Minerals program during 1942. The exploratory work comprised geologic and topographic mapping, diamond drilling,,bulldozer and hand trenching, sinking test pits, rehabilitation of old workings, sampling alunite exposures, and constructing and repairing roads.ACKNOWLEDGNENTSIn its program of exploration of mineral deposits; the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report. The Metallurgical Branch, R. G. Knickerbocker, chief, analyzes samples and performs beneficiation tests. Both these branches-are under the supervision of Dr. R. S. Dean, assistant director.With particular reference to this publication, acknowledgment is given to Richard E. Mieritz and William E. Young, who assisted on the project at various times; P. T. Allsman, chief. Salt Lake Division, Mining Branch, who advised on exploratory problems and gave valuable assistance in preparing the report and illustrations; A. P. T. Schumann, for preparing the illustrations; and to Gordon L. Bell, Max Willard, and Eugene Callaghan, of the Geological Survey, who cooperated as representatives of that agency."

Nov 1, 1946

By R. Farnfield, W. Birch

Arguably, some of the most restrictive statutory blast vibration requirements attached to mineral extraction operations can be found in the United Kingdom. Such limitations are, as a rule for the UK, stipulated together with a required statistical confidence that has to be observed in the blast design process in order to ensure total planning compliance. A key element in this procedure is the effect imparted by vibration data scatter from previous blasts as this becomes reflected in the site’s operational standard error statistic and in turn directly influences the maximum instantaneous charge weights that can be justifiably employed. The greater the scatter, the lower the compliant charge weights become.

Jan 1, 2006

By Don Conrad, Tom Friend, Bill Wiehagen, Lynn Rethi

On-the-job training (OJT) is a very common method of teaching job skills. Much of the training is done by experienced workers. This paper discusses small investments that can help improve the effectiveness of OJT. Effective OJT involves some structure and planning in the transfer of responsibility for task performance from the trainer to the novice. Assisting the OJT trainer could involve helping develop up-to-date job analyses and offering strategies for teaching and evaluating job skills. The scope of this paper addresses (1) organizational considerations supporting structured OJT, (2) general strategies for structuring OJT, (3) a typical approach for conducting OJT, (4) characteristics and duties of OJT trainers, and (5) limitations of OJT as a teaching method. Health, safety, and operational skills can be connected through training. Haul truck operator training is used to illustrate some of the concepts discussed in this paper.

Jan 1, 2002

By R. Gunda

Due to the rapidly increasing production rates and deepening of mine working areas, there is a drastic rise in the number of thermal issues to be addressed for maintaining a safe mine environment. As high temperatures and humidity in underground mines could affect the health and performance of workers, and ultimately the production rate, it is necessary to provide a properly controlled safe environment. The backfilling of stopes in metal, non-metal mines results in different thermophysical properties for the hanging, side and foot walls, modeling of which is not provided by any existing mine climate simulation software. This paper presents the modeling of such a single stope using the MULTIFLUX (MF) software, developed at University of Nevada, Reno. A special case is presented in this paper, where a case study from the Homestake mine in the US with a drift and ramp connected to a stope with high Virgin Rock Temperature (VRT) and various spot heat sources is modeled in MULTIFLUX and CLIMSIM, and the results are compared against each other. Another case is presented in which the stope of the previous cases is modeled with walls, each having a different set of thermophysical properties. These results are compared with the former results to analyze the effect of anisotropic properties.

Jan 1, 2011

By Yin Zongze

The pile foundation of Sutong bridge pylons is an extra large pile foundation. The length of piles is 115m, and the diameter of the piles is 2.5-2.8m. Since the traditional design method may not determine the settlement and capacity reasonably for such a large pile foundation, the finite element method is used to study stress and deformation of the foundation. The interface element is set to simulate the possible slide between piles and soil layers. The hyperbolic model is taken for soils. Parameters are determined from triaxial test first, and then modified by back analysis on basis of in-situ loading test. The computation results show that the axial force of piles changes with the location of the pile. Outer piles support greater axial force and also friction. The settlement will not be greater than 26cm. The stress and deformation of the pile cap, the abutment, are obtained too. The whole foundation is safe.

Jan 1, 2006

By Arnold M. Lansche

[Selenium and tellurium are rare elements in the earth's crust. Their scarcity and primary dependence of supply on copper and lead output are in consonance with the relatively small quantities consumed at 1964 level. Production depending on output of copper and lead creates a supply situation- which would appear to militate against development of large-scale usage of these elements. However, supplies have adequately met. demand in the past decade and can be increased substantially if warranted by new uses for either selenium or tellurium Ores of copper and lead re the principal sources of selenium and tellurium. Byproducts from the smelting and refining of copper and lead concentrates are incorporated in refinery anode slimes from which selenium and tellurium metal are recovered.]

Jan 1, 1967

By D. A. Lindsey

Gravel lithology affects the quality of aggregate because different rock types in gravel have different physical and chemical properties. The lithologic composition of alluvial gravel reflects the composition of its source terrane and the variable effects of weathering and transport on each rock type. This report discusses lithologic controls on aggregate quality in the mountain-front environment of the Colorado Front Range. Lithologic controls on aggregate quality of gravels were evaluated using pebble count data. Gravel lithology along the Front Range shows both temporal and regional variation. The principal variable in gravel lithology is quartz plus quartzite, of which quartzite is commonly more abundant. Large quantities of metaquartzite derived from the mountain front southwest of Boulder, Colo., were dispersed northeastward during deposition of the oldest Front Range gravels. Average quartz plus quartzite is greatest in the oldest gravels. Aggregate quality is probably enhanced by large quantities of quartzite. Abundant volcanic rocks in gravel may enhance aggregate quantity, but such occurrences are local in extent. Abundant sedimentary rocks in gravel, mainly sandstone near the mountain front, may decrease aggregate quality.

Jan 1, 2002

By J. M. Cardoso, E. F. Quadros, A. Chiarini, F. Fernandes, G. Vilela, J. Ireno, L. C. Agostini

Based on the geological-geometric characterization of the basaltic rock at the site of a factory for chemical products situated in the Southern region of Brasil, and on results of a significant number of packer tests, the principal directions of flow were estimated, taking into consideration the intersection and the orientation of the joints and the amount of contaminant flow measured in each interval. The tests were performed using the multi-packer hydraulic multitest probe of IPT (HMTP) instrumented with an electric conductivity meter. A method of analysis for three-dimensional evaluation of the amount of contaminant flow in the area was proposed for future mitigation of the problem. Basé sur une caractérization géologique-géotechnique de la roche basaltique existant sur un site dune fabrique de produits chimiques située au sud du Brésil et sur les resultants dún nombre significantif déssais du type packer, les directions principales d´écoulement ont été estimées en considerant l´intersection et orientation des joints et la quantité de contaminant mesurée sur chaque intervale d´essais. Ceux-ci ont été realizes en utilisant une sonde multipacker developée au IPT – São Paulo (HMTP) instrumentée avec un mesureur de condictivité électrique. Une méthode d´analyse 3-D pour l´évaluation du transport du contaminant sur ce site a été proposée pour une future mitigation du problème. Auf Grund der geologischen Struktur des Basalts auf dem Gelände einer chemischen Fabrik in Südbrasilien und der Ergebnisse einer ansehnlichen Zahl von Pumpversuchen wurden die Hauptfließrichtungen bestimmt unter Berücksichtigung des Kluftgefüges und der in jedem Intervall gemessenen Menge kontaminierten Wassers. Die Versuche erfolgten mit dem im IPT entwickelten Verfahren (HMTP) mit Mehrfachpackern und elektrischen Leitfähigkeitsgebern. Ein analytisches Verfahren zur dreidimensionalen Ermittlung der Mengen kontaminierten Wassers wurde für die künftige Befassung mit dem Problem entwickelt.

Jan 1, 2003

By H. Wyslouzil

"The Kelsey Centrifugal Jig is a gravity separation device which utilizes the principles of the conventional mineral jigs but with the additional feature of being able to vary the apparent gravitational field. This is accomplished by utilizing the specific induced movements of the conventional jig within a centrifuge.Pilot plant trials have been underway since July 1988 to evaluate the potential applicability of this technology to various process streams at Rio Kemptville Tin.The grade/recovery relationships for samples treated in the jig were consistently better than results obtained from tables. Recoveries of more than 90% were attained at concentrating factors ranging up to 20. When compared with electrostatic separators, the jig achieved equivalent metallurgical results in a two stage process, without the expensive requirement of filtration and drying. Recoveries exceeding 96% were achieved with final concentrate grades averaging higher than 60% tin.INTRODUCTIONMineral jigs have been used for hundreds of years. Many different types have been developed, and each one has numerous variations. In recent years, the idea of applying centrifugal forces to conventional jigs has been put to practical tests and today a number of units are in commercial production. In principle, by enhancing the apparent gravitational field, it should be possible to recover finer particles by overcoming viscosity and surface effects which tend to limit existing gravity devices. In addition, it may be possible to use gravity to separate minerals with much smaller specific gravity differences."

Jan 1, 1990

By William R. Yernberg

The combined 78th Annual Minnesota Section of SME Meeting and 66th Annual University of Minnesota Mining Symposium was held April 19 and 20, 2005, in Duluth, MN. More than 300 mining professionals, including engineers, executives, mining managers and suppliers, from throughout the United States and eastern Canada attended the meeting. This year’s theme was “Global Demand: A Window of Opportunity.” The meeting included a keynote address, technical presentations and a trade show. The atmosphere at this year’s meeting was upbeat. The iron ore mining industry in Minnesota is experiencing one of its biggest turnarounds in history. Because of greater demand, iron ore prices increased 20 percent during 2004 and 71.5 percent so far in 2005.

Jan 1, 2005

By Lucien Eaton

THE use of filling in mines is less common in the United States than it is in Europe, where in some places it is required by law. In most cases the filling is placed by hand, and the material used for this purpose is the waste from development and that sorted from the ore in the stopes. When these sources provide an insufficient supply, additional rock must be quarried on surface or mined underground, or some other material :st be used. In different parts of the world sand, clay, gravel, culm, nulated slag, mill tailings, and even ashes, have been used as filling material in place of or in conjunction with rock. Of all the materials used for filling the best is probably clean sand. Gravel, finely crushed rock, granulated slag and coarse mill tailings are almost as good, and the methods used for placing and confining sand will apply equally well to any of these. The advantages of sand are its comparatively slight compressibility and the ease, economy and convenience with which it may be placed. On account of the voids, which necessarily occur in fills made of coarse waste, such fills will compress 10 to 25 per cent before they develop their full strength, whereas clean sand seldom compresses more than 5 per cent. Sand is especially desirable when practically complete filling is required, and sand derived from mill tailings, especially when not thoroughly cleaned, has been remarkably effective in sealing off and extinguishing mine fires. When natural sand is available on surface, or when it can be obtained from the mill tailings or tailings dump, the cost of using this material for fill will probably be considerably less than that of rock. In this paper it is not proposed to discuss all methods of filling, butt to describe some of the methods used for placing sand fill and to make a brief comparison of their merits.

Jan 1, 1932

he Wyalong goldfields were discovered in September, 1893, Messrs. Neeld and Sons, owners of the principal mine, being the pioneer prospectors. During the earliest days of the field the ore was sent to Barmedman, a distance of eighteen miles, for treatment at a battery there. The field rapidly increased in importance, and it was not long before a public battery was established on the spot. After some considerable quantity of ore was treated by this process, it became apparent that battery treatment was quite unsuitable for the richer ores, involving, as it did, considerable loss in the tailings. Recognition of this fact led to the erection, in 1895, of plants by the Wyalong Chlorination and Cyanide Works, owned by Mr. Walter Sully, for treatment by their processes; followed, at a later date, by Messrs. Neeld and Sons Chlorination Works. The Wyalong Chlorination and Cyanide Works, after a delay of twelve months in the erection of their plants, have since catered continuously up to the present time for the requirements of the field.Their plant consists of a No. 3 Gates' rock·breaker, a revolving dryer, a No. 5 Krupp mill, revolving roasting furnace with finishing hearth, two chlorination vats of 20 tons capacity each, "nine cyanide vats of 30 to 100 tons capacity, two Wheeler pans and three chlorine generators. The ores are purchased outright on assay at a fixed scale of charges, and treated by the owner of the works on his own account.

Jan 1, 1903

By Brigitte Lacouture, Yeen Shien Hwang, David Lin

"A baseline survey of the partially open lead regrind circuit at Red Dog Mine indicated poor regrind efficiencies for the three parallel 450 HP tower mills. Driven by the high energy cost and the potential metallurgical gain brought by improved mineral liberation, the Red Dog lead regrind circuit was optimized in two stages.In the first optimization stage, different circuit layouts were evaluated in two plant trials. In June 2003, the regrind circuit was changed to a fully closed circuit. This reduced the tower mill requirement from three to two mills. The circuit modification payback was 11 days through power savings alone.The second stage of optimization was the evaluation of reagent addition. To improve pyrite depression, sodium cyanide was added to the feed of the lead regrind tower mills and tested in a series of plant trials over several mill feed stockpiles. Galena selectivity against pyrite was found to improve in these plant trials. Due to environmental sensitivities, no net increase in cyanide addition to the plant occurred and thus no increase in the cyanide concentrations in the tailings pond or the environment will result.The lead regrind optimization work improved the overall lead metallurgical performance and reduced energy and reagent costs. Economic analysis showed that annual profit increased by as much as US$3.0 M."

Jan 1, 2005

By Daniel Hack

A few progressive mining software companies have recognized the benefit of broadening their capabilities to the sand and gravel (aggregate) industry. The most promising new developments have been designed for use with Surpac Vision, one of the world’s leading geological modeling, mine design, and production management systems. Surpac’s broad user-base, who have always had a propensity for customization, are now focusing on development of solutions in the Tool Command Language (Tcl), an interpreted scripting language. Surpac Software International made changes to TCL to add Surpac specific extensions, thus creating the Surpac Command Language (Scl). The Tcl interpreter, including Scl extensions, is bound into the Vision executable to provide a seamless interface to the data objects used internally by Vision, the GUI, and the 3D rendering system. Custom solutions can be incorporated as Vision extensions, or as stand alone-modules used in correlation with modeling, design, and planning functions.

Aug 25, 2002

By Ren G. Dong, Jay Kim, Daniel E. Welcome, Won Joon Song, Charles Hayden

Prolonged, extensive exposure to hand-transmitted vibration could cause a series of vibration-induced disorders in the vascular, sensorineural, and musculoskeletal structures of the human hand-arm system, which have been collectively called hand-arm vibration syndrome (HAVS).1 To assess the risk of HAVS the international standard ISO 5349-1 (2001)1 recommends using the root-mean-square (rms) acceleration of the measured vibration with a frequency weighting. While a few epidemiological studies have reported results consistent with the predictions made according to the recommendation, many other studies have reported results with large discrepancies.2 This may be partially attributed to the time-averaging effect involved in calculation of the frequency components, especially for impact type tools. Because the spectral characteristics of impact tools change dramatically with time, a time-frequency (T-F) analysis can provide better characterizations of such highly transient vibrations. The analytic wavelet transform (AWT) is an ideal T-F analysis tool because it possesses the advantages of both the Fourier transform and the wavelet transform.3 The objective of this study was to explore the application of the AWT method for characterizing the impact tool vibrations and assessing their exposure risk. Methods Five tools (two chipping hammers, two riveting hammers, and one concrete cutting saw) were used in this study. The saw vibration was measured when it was used to cut a section of road pavement during a repair. The vibrations on the other tools were measured by the procedure specified in ISO 8662-2 (1992).4 A sampling rate of 16,386 Hz was used in the measurement. The AWT and Fourier analysis were applied to these signals and to identify their characteristics. Results Figure 1 compares the T-F characteristics of the accelerations measured from the relatively steady concrete saw and a riveting hammer. The frequency weighting specified in ISO 5349-11 was applied in the calculations. The comparison clearly shows that the two tools have completely different T-F characteristics.

Jan 6, 2006