Search Documents

By W. M. Cross

Bubble attachment time measurements for the rare-earth phosphate minerals monazite and xenotime were made as a function of oleate concentration, sodium fluoride addition, and temperature. Results indicate that the rare-earth phosphates behave similarly to other phosphate minerals, notably collophanlte and fluorapatite, which have been studied previously. The addition of sodium fluoride yielded a modest decrease in bubble attachment time with fluoride additions below the apparent fluoride surface precipitation point, while at fluoride additions greater than the apparent precipitation point a significant decrease in attachment time occurs. Increasing the temperature or the system gave a slight decrease in bubble attachment time in the absence or sodium fluoride. With sodium fluoride addition and below the apparent fluoride surface precipitation point, an increase in temperature actually increased the attachment time. For sodium fluoride additions above the apparent fluoride surface precipitation point, a temperature increase significantly decreased the attachment time.

Jan 1, 1989

By David Seaman, J-P Franzidis, Emmy Manlapig

"A new device has been developed to directly measure the bubble loading of particle-bubble aggregates in industrial flotation machines, both mechanical flotation cells as well as flotation column cells. The bubble loading of aggregates allows for in-depth analysis of the operating performance of a flotation machine in terms of both pulp/collection zone and froth zone performance. This paper presents the methodology along with an example showing the excellent reproducibility of the device and an analysis of different operating conditions of the device itself.The device has been used to investigate the froth selectivity of attached particles. Simultaneous measurements were made using a different froth recovery measurement technique in the same flotation cell. A comparison of these techniques shows that in this case, particles are selectively detached from bubbles at or near the pulp-froth interface.INTRODUCTIONA flotation cell can be considered to operate in two distinct phases or zones; namely the pulp or collection phase and the froth phase. The pulp zone is responsible for the formation of hydrophobic particle-bubble aggregates, whilst the froth phase is responsible for the separation of these aggregates from surrounding suspended hydrophobic and hydrophilic particles. Thus, the froth phase is the grade determining phase in flotation. A measurement of the bubble load (the mass of particles attached to air bubbles in units of mass/volume) will enable the analysis of the performance of both the collection zone at creating bubble-particle aggregates and also the froth zone at separating these aggregates from surrounding pulp.A measure of froth zone performance that has been used extensively in flotation research is the Froth Recovery, Rf, of a particular system. Froth recovery is defined as the mass of particles collected in the concentrate launder by true flotation as a fraction of the mass of particles entering the froth phase. The measurement of bubble load allows for this term to be calculated easily, rather than having to go through the laborious task of, for example, changing froth depths to determine this performance criterion (Contini et al., 1988; Vera et al., 1999b; Feteris et al., 1987)."

Jan 1, 2004

By W. L. Price

Since first introduced in the United States in 1964, rail mounted bucket wheel stacker-reclaimers have gained wide acceptance by users. The coal burning power plant group has adopted this new storage tool most quickly. The actual history is traced in this area in some detail. Installations in phosphate and steel mill ore storage and a listing of present users are included.

Jan 1, 1969

By J. W. Thomson, H. J. Lloyd, R. J. Taylor

"THE HOLLINGER MINE has been producing gold and by-product silver almost continuously for forty-eight years. The value of current production is $10,000,000 annually from one million tons of ore. Its management •has, particularly over the past decade, increasingly . concerned itself with the problem of profitable operation in a time of steadily rising costs and a fixed price of gold. At one period in the life of the mine, before World War II, production resulted in yearly profit margins that were stable and relatively thick. In winning gold from a series of inconsistent vertical ore lenses, operating management was much better protected than it is today against a general rise in cost or dip in grade of ore. The tissue-like thinness of present-day margins demand more careful handling. A sharp rise in costs, if protracted, could easily rip the tissue to shreds and close down the business. The counter-measure of raising grade and gutting the mine would bring on the end perhaps more rapidly, without having contributed much to the recovery of our national re-sources, nor to community welfare. The alternative is to keep costs under control."

Jan 1, 1960

By H M. Ahmed, W S. Dunbar

Construction of cave mining systems requires significant capital expenditure and long-term commitment of human, equipment and material resources before production commences. Risks and uncertainties of these large-scale mining projects are significantly higher than for small-scale projects. This is due to the complexity and interactions of the construction schedule components and the large scale and uniqueness of such projects. One way to successfully manage construction uncertainties that would lead to schedule delays is to include a reasonable cost contingency in the budget estimation. A real options approach based on the least-squares Monte Carlo (LSM) method is used to estimate cost contingency associated with schedule uncertainty in mass mining projects. Cost contingency is estimated as the cost of potential project crashing (acceleration) decisions, which pays for not extending the schedule. While such a significant undertaking is expected to be subject to some delays, these can have an enormous impact on the economic value of such projects. The value of the crashing option was explicitly formalised into the process of valuation, as it is assumed to be a single option being considered in the valuation at every decision point prior to the construction completion date. As a part of the proposed method, a stochastic function for the percentage of remaining scope of work for the remaining duration of the entire project was integrated into a framework of numerical simulations. This ensured that this function can implicitly account for sources of schedule uncertainties for projects represented by multiple and overlapping work packages. The LSM method was applied to a real case scenario in an operating block cave mine, with modified scale and features. The results yielded by the LSM method indicated that significant changes in capital budget allocation stem from variation in a contractor’s risk perception and confidence level of estimated delays.CITATION:Ahmed, H M and Dunbar, W S, 2016. Budget estimation and contingency allocation of block cave construction using least-squares Monte Carlo real options, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 801–808 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By William Hutton Blauvelt

An official of one of the prominent iron companies of the South recently made the following statement during a discussion of the present conditions of the Southern iron business: " The trouble with us in the South has been that we have been satisfied to buy iron and coal lands, build blast-furnaces, and make pig-iron. We stopped at pig-iron, and as a result we are all poor. The South needs diversified industries, and needs to work up its raw products into articles the Southern market can use. If we had realized this sooner, some of us might now be rich." The South is awakening to this view, and in the Birmingham district alone one basic steel-mill is already in operation, and in a year's time another and much larger one will be turning out rails and shapes, with rod- and wire-mills in prospect. It is to chronicle another metallurgical step forward in the same district that I have prepared the following description of the new by-product retort coke-oven plant recently put in opera-

Jan 1, 1899

By L. A. Cornish, S. N. Prins, R. Süss

The work is being done using the Thermo-CalcTM software, and the database is being built up by obtaining good thermodynamic descriptions of all of the possible phases in the system. The database supplied did not cover all of the phases, and these had to be gleaned from literature, or modelled using experimental data. Similarly, not all of the experimental data were known, and where there were gaps or inconsistencies, experiments had to be undertaken. A preliminary version of the database was constructed from assessed thermodynamic data-sets for the binary systems only. The binary descriptions were combined allowing extrapolation into the ternary systems, and experimental phase equilibrium data were compared with calculated results. Very good agreement was obtained for the Pt-Al-Ru and Pt-Cr-Ru systems, which was encouraging and confirmed that the higher-order systems could be calculated from the binary systems with confidence. Since some of the phase models in databases were different, these phases had to be remodelled. However, more work is ongoing for information concerning the ternary phases present in the Al-Cr-Ru, Pt-Al-Ru (two ternary compounds in each) and Pt-Al-Cr (possibly more than three ternary compounds) systems. At later stage of the work, problems with the thermodynamic descriptions of the Cr-Ru and Pt-Cr binary systems were found. A programme of experimental work to overcome these has been devised, and is being undertaken. Keywords: Pt-based alloys, phase diagram calculations.

Jan 1, 2006

By Joseph P. Nugent

The new combination gypsum plaster and gypsum wallboard plant of Compania Industrial Kaiser S.A., the first of its kind in Mexico went into production in April of 1969. This was approximately fourteen months from the signing of the formal order for the plant and equipment. Compania Industrial Kaiser S.A. is an affiliate of the Kaiser Gypsum Company in the United States and will market practically the same line of products and to the same standards as those produced in American plants. Located in the City of Puebla, the plant will readily service the major Mexican sales areas. It is approximately 85 miles away from Mexico City on a modern, four-lane, divided highway and distribution to other major consumer areas can be readily effected by the use of a good highway system, as well as, by rail. This, plant is the, sixteenth Gypsum Wallboard Mill supplied abroad by my company, United States Wallboard Machinery Company. Other installations are in Australia, New Zealand, Chile, England, Scotland, Ireland, Finland, South Africa, Latvia and Germany. Two new mills are on order; a small unit for Brazil and a comparatively large unit for New Zealand. All these mills have one thing in common with plants in the United States and Canada; they are equipped with standard, time-proven and tested equipment and they are designed in accor¬dance with the latest engineering thinking in order to produce efficiently, the highest quality product at lowest cost. They differ generally in the size of plant, the factors that brought them into being and in the market that they supply. I believe that these differences will be of interest to you.

Jan 1, 1969

By J. A. Flinn

Phelps Dodge’s Morenci copper mine has had six drills, six track-dozers, 16 shovels, two loaders, and 90 haul trucks equipped with either Caterpillar, Aquila, or Modular GPS systems for nearly three years. The Caterpillar Computer-Aided Earthmoving System is an open-architecture system, which allows for inputs to enhance orientation solutions and system functionality. This system has begun a new phase that leads to an intelligent mining system. Optimization techniques of the current system and inputs are reviewed. In addition, some practical issues of implementing new technology in a mining environment have been identified to aid in this new phase.

Jan 1, 2000

By I Thin, L Morizzi, C Seymour, G Mungur

Olympic Dam has been investigating mine design options for the South Mine Area (SMA), which will continue using the existing sublevel open stoping (SLOS) method. The SMA is an undeveloped mining area, located south of the existing underground mining areas currently in production at Olympic Dam. The SMA study reached the stage where geotechnical inputs were required for stope design, infrastructure location and ground support forecasts. A large database of geotechnical data was collected to inform open pit designs for the ODX (Olympic Dam expansion) project (resulting from 659 drill holes). This geotechnical data has since been reprocessed to align with design inputs required for the SLOS mining method. The result has been the construction of a preliminary three-dimensional mining rock mass model (MRMM) that has been incorporated into preliminary stope mine design and infrastructure layout assessments, which have taken into account the predicted prevailing ground conditions.As with any model, it is necessary to improve the confidence in its predictability; therefore the model must be calibrated. The preliminary SMA MRMM was no exception. First pass calibration was possible with results from underground geotechnical window mapping from exposed rock mass conditions in the lateral development and surface geotechnical holes for ventilation shafts.The SMA project continues to advance and has started a program of resource drilling. Selected holes have been identified that target data limited areas. This will ensure that the data gaps are infilled in order to maintain the required data density required to improve the model confidence. In addition, further underground window mapping in the SMA will provide ‘mine scale drill hole’ data that can be used to either update the MRMM or as part of planned future calibration. Stope performance data from stopes will provide further valuable data for calibration purposes.The proposed paper will present the process and findings that have been followed in order to establish a well calibrated geotechnical model that can be used with an acceptable level of confidence in the ongoing refinements of the mine design and planning process for the SMA.CITATION:Thin, I, Morizzi, L, Mungur, G and Seymour, C, 2016. Building and calibration of a geotechnical model for sublevel open stope design at Olympic Dam, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 523–532 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By J A. Wells, K G. Thomas, R F. Dewhirst

"One of the contributing factors to the extreme cost escalation in the first decade of the 21st century was the increase in the amount and cost of engineering work that went into studies and projects. Various reasons for this were identified, including unsatisfactory productivity due to a shortage of experienced/qualified engineers, the increased complexity and infrastructure requirements of many projects due to location, metallurgy that is more challenging and increasing environmental and social requirements. These conditions often led to unsatisfactory project results in terms of cost and schedule blowouts and created a loss of confidence – both internally and externally – in the industry’s ability to complete projects on time and on budget.Technical fundamentals aside, the experience and effectiveness of project teams has had, and continues to have, a major impact on project cost, schedule and ramp-up to nameplate capacity and operating parameters. There are unfortunately too many examples of where project teams have not been as effective as they could or should have been, all to the ultimate detriment of the project.Using the authors’ extensive experience on both owner’s and engineer’s teams, this paper discusses some of the main reasons for suboptimal team, and hence project, performance and offers thoughts on how best to build and maintain project teams. The analysis and conclusions drawn are built around the Tuckman model of group development known as ‘forming-storming-norming-performing’, which was first proposed some 50 years ago. Given the importance of good teamwork to project success, understanding how project teams grow and become efficient and productive is an essential part of good project management that should receive more attention.CITATION:Dewhirst, R F, Thomas, K G and Wells, J A, 2016. Building and maintaining effective project teams, in Proceedings Project Evaluation 2016, pp 38–48 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 8, 2016

The structural design of a mine haul road involves the determination of cover thickness requirements above the in-situ or sub-grade material. The specification of these layerworks is a critical component in the overall road design process. Poor design often leads to premature failure of the road, safety is often compromised and productivity and equipment service-life will certainly decrease. Historically, the California Bearing Ratio (CBR) cover-curve design method has been widely applied to the structural design of mine haul roads. More recently, established mechanistic design principles have superceded the CBR approach to haul road design, using a multi-layer model to represent the various road structural layers. The structural design and associated layer thickness requirements are then determined following a maximum strain criterion. This paper develops a case-study evaluation of the CBR cover-curve and mechanistic design methodologies and through a comparative analysis of layerworks and materials, highlights how improved structural design can be achieved mechanistically.

Jan 1, 2011

By Marco D. Boscardin

Control and mitigation of building response to construction activities are assuming a greater role in design decisions for underground construction. Alternatives for controlling building response have multiplied with the continued development of ground modification methods, better control of construction activities that cause ground movements, and increased understanding of building behavior and response. This paper describes approaches to estimating building response to construction-related ground displacements caused by adjacent excavation and highlights the discussion with several case history examples. Examples discussed includes experiences with two, seven-story historic structures, supported by timber piles with granite block pile caps, which were underpinned in preparation for ground-freezing ground stabilization and tunnel construction beneath the buildings. The elevation of each building column was monitored and elevation adjustments were actively performed during construction. The second example examines the performance of a slurry wall braced cut, 45 to 50 feet deep penetrating through a stiff crust into a soft clay layer and associated building response. This cut was immediately adjacent to two, approximately 15-story office buildings, which were supported by deep foundations founded in the stiff crust.

Jan 1, 2003

By Geraldine Woods

I work for the State of Washington as an Explosives inspector. My paper will describe the mission of the Wa. State Dept. of Labor pertaining to explosives and the regulation of explosives in the State.Blasting safety is high on the public safety list and the regulation of explosive use and storage has been mandated through legislature. The Dept. considers pro-active partnering forexplosive safety preferable to after-the-fact citations for non-compliance.In some cases, the Dept. will issue civil citations with monetary penalties, meant to be a deterrant, of course, to blasters who choose not to comply with the explosive regulations of the State.The Dept. has also revoked and suspended blasting licenses. In some instances, the Dept. has allowed recipients of citations with monetary penalties to reduce the amount paid by attending technical training classes. The idea here, is to reduce the chance of reoccurence of unsafe blasting practices. The State of Washington partners with MSHA in the regulation of explosives use and storage in mines, pits and quarries in the Stateas well as working closely with law enforcement, State and local fire marshals, ATF,and is active in ISEE in part of it’s ongoing effort to promote explosive safety and establish communications in a nonadversarial way with explosives users. My paper will include some statistics on licensing in the State, pounds of explosives used, inspection numbers, numbers and types of complaints with information from the inspections resulting of these complaints. My paper will include examples of storage, both good and bad, examples and pictures of fly rock incidents, accidents, near-miss close calls, break-ins, thefts, and abandoned explosives. This paper may also include a brief summary of my opinion of explosive regulation and my job as a regulator, including examples of high and low points of the job, joys and frustrations.

Jan 1, 2002

By Brian Fulcher

In April 1997, Kiewit/Parsons Brinckerhoff (K/PB) completed the 7,600-m (25,000-ft) primary access tunnel for the Yucca Mountain, NV proposed high-level nuclear waste site. K/PB then began boring an exploratory east-west cross drift tunnel at the site. The 2,681-m (8,796-linear ft)East-West Cross Drift Tunnel was excavated through volcanic tuffs having zones of incompetent rock using a rebuilt Robbins 5-m (16.4-ft)hard-rock tunnel boring machine(TBM) with a special arrangement of supporting equipment. This portion of the Yucca Mountain project was completed in eight months.

Jan 1, 2000

By Lin Daoyi

In this paper, we have adopted the high pressure jet-grouting curtains to seal the sea-water, and to consolidate the wall of the well for deep foundation diteh, make a pladge of building and construction of deep foundation was primarily on progress without water. This paper, we have been given a test for pumping water under mainly the circumtances of sealing condition and to report in advance the capacity of seawater seeping into the gam curtains in the process of building and construction of deep foundation.

Jan 1, 1991

Certain information contained herein regarding Champion Minerals Inc., including management?s assessment of future plans and operations, may constitute forward-looking statements under applicable securities law and necessarily involve risks, including but not limited to risks associated with mining exploration, operating costs, production costs, volatility of share prices, currency fluctuations, imprecision of resource and reserve estimates, environmental risks and ability to access sufficient capital from internal and external sources. As a consequence, actual results may differ materially from those anticipated in any forward looking statements. Plans, intentions or expectations disclosed in any forward-looking statements or information should not be read as guarantees of future results or events, and will not necessarily be accurate indications of whether or when or by which such results or events will be achieved. Except as required by law, Champion Minerals Inc., expressly disclaims any intention and undertakes no obligation to update any forward looking statements or information as conditions change. The historical mineral resources mentioned are strictly historical in nature and are non-compliant to National Instrument 43-101 mineral resources and mineral reserves standards, and should therefore not be relied upon. A qualified person has not done sufficient work to upgrade or classify the historical mineral resources as current National Instrument NI-43-101 compliant.

May 1, 2011

Building the Unified Comminution Model The Unified Comminution Model (UCM) was formulated with the vision of bringing all comminution models onto a common base. The structure of the model relies on knowledge of the mechanical environment in the comminution devices to predict the modes and rates of collision in a device. A detailed understanding of the breakage modes and an ability to correctly test these modes for the ores in question is then required to feed into the UCM. A model structure has been developed that has the capability of dealing with multiple modes of breakage, such as low energy impact surface damage, chipping, sliding abrasion, cumulative impact body breakage and the transition of rock between modes. A critical review is presented on the shortcomings and limitations of utilising the discrete element method (DEM) to provide the mechanical environments. The assumptions and applicability of utilising DEM in milling models are presented and proposed routes to building a realistic mechanistic model are proposed. Based on this more realistic measures of collision energy have been derived from the DEM simulations, which better mimic the real breakage tests. Generic forms of the collision energy distributions have been observed and developed into functional forms for use in the simulation environment. The method of application of this model to a pilot SAG mill is presented.

Sep 13, 2010

For tax purposes a mining company is a New Zealand company whose principal source of income is from the business of mining, or exploring for certain specified minerals in New Zealand. New Zealand tax law distinguishes between a non-resident mining operator and a mining company, with the only major difference in tax treatment being the corporate tax rates. New Zealand mining companies are taxed at 28 per cent, whereas non-resident mining operators are taxed at 33 per cent of taxable income. These provisions also apply to the petroleum mining industry. Individuals who carry on the business of mining are also specifically defined in the Act. They are termed as 'resident mining operators'. Non-resident mining operators are non-residents of New Zealand who carry on mining ventures as a business in New Zealand. Mining ventures are defined as the exploring, searching and mining of specified minerals, including development work carried out for profits. Similar provisions apply to the petroleum mining sector. Specified minerals are defined in the Income Tax Act 1976 ('the Act') and while no useful purpose is obtained by listing them in the paper, they include a larger number of industrial and commercial minerals. The Minister of Finance is also empowered to add to the list by publishing his determination in the Gazette.

Jan 1, 1988

By Norman Paley, John Kells

The climate and location of the Red Dog Mine present several challenges to blasting operations. The mine is located north of 68º latitude, in an area of continuous permafrost. Ground temperatures are below freezing year-round and air temperatures range from -40 to 70°F (-40 to 20°C). Because there is no overland access to the mine, the entire year’s supply of bulk explosives, approximately 7,000,000lbs (3,175,000kg) is shipped in by barge during the 100 day shipping season when the port is ice-free. The first week in July is the earliest that new product arrives at the port. Emulsion usage is maximized from mid April through October when surface water fills the blastholes during drilling. This necessitates that a considerable portion of the bulk explosives are stored for 10 months or more before usage. The emulsion is routinely pumped from the ISO containers at temperatures of 20ºF (-7°C). The mine engineers conducted a testing program during the 2001-2 blasting season to identify the bulk explosives best suited for the conditions at the mine. A secondary goal was to decrease the usage of sensitized emulsion, as this is the most difficult portion of the explosives order to ship. To ensure repeatability when transferring the results to the day-to-day blasting operation, the majority of the testing was incorporated into normal blasting operations in the field. The mining methods used at Red Dog Mine make direct fragmentation analysis impractical and performance testing in the field relied primarily on VOD measurements. The products were also tested for their ability to be pumped in cold temperatures.

Jan 1, 2004