Search Documents

By A. Amiel

Tarkwa Gold Mine is owned by Gold Fields Ghana, IAMGOLD and the Government of the Republic of Ghana in a 71%, 19% and 10% ratio. The mine is operated by Gold Fields Ghana. This large, low-grade, open pit, gold mining operation is located in Tarkwa, in the Western Region of Ghana, approximately 320 kilometres by road, west of Accra, the capital of Ghana, West Africa. In the Financial year ended June 2007, the operation mined a total of 108 million tons of which 22 million tons was ore. The mined ore is processed through three gyratory crushers supplying two heap leach pads (north and south) and a carbon-in-leach (CIL) plant. Before the 6 Sigma project commenced, the current fragmentation was resulting in sub-optimal feed size to these crushers. It was decided to use 6 Sigma methodology to improve the fragmentation. A defect was defined as a fragmentation analysis indicating less than 95% passing 750 mm. The objective was to improve fragmentation in order to achieve a constant throughput to the north heap leach crusher of 1500 t/h, a 5% increase in pit loading efficiency and a 50% decrease in rock breaker hours, equipment damage costs and in-pit sheeting costs respectively. However, this was not to be achieved at the expense of grade control as Tarkwa is exploiting a low grade, high volume deposit and therefore ore dilution must be kept to a minimum. This paper is intended to take the reader through the various 6 Sigma phases of the project (define?measure?analyse ?improve?control), which have resulted in a 10% reduction in loading times, of which half has been attributed to improved fragmentation, as well as a substantial increase in blasted stocks. The focus has been on both drilling and blasting parameters as both processes had to be taken into account. These parameters are technical but personnel factors were also identified and dealt with as they arose. In order to measure the impact of any change in the process parameters on the fragmentation size distribution, cameras have been acquired. One has been installed looking into the bowl of the north crusher and the other one was dedicated to field observation, of individual blasts. Both are used for ongoing fragmentation analysis. At Tarkwa, mining efficiency is strongly dependent on good fragmentation as well as the presence of unblasted ?toes? on the pit floors. Crusher throughput depends on an acceptable ore fragment size. Compliance with plan for actual hole depths was temporarily monitored by manual hole dipping, but this is now being replaced with a fully automated drill data management system developed by Sandvik and Modular Mining. The Six Sigma methodologies, using control charts based on data collected in the field, allowed the mine to improve methods for the control of blasted material. It also enforced the implementation of a quality control programme encompassing the entire drill and blast process.

Jan 1, 2008

By J. Muller

Keywords: Pyrometallurgy, blast furnace, slag viscosity, slag liquidus temperature, phase equilibria The viscosity of molten slag in blast furnace operations is an important process variable, influencing the rate and location of reactions inside the furnace, as well as the ease with which the final slag could be removed from the furnace. To optimize these processes, it is necessary to estimate the slag viscosity and liquidus temperatures as accurately as possible, and know the target values. Models to predict viscosities and liquidus temperatures, incorporating phase equilibrium calculations, have been developed and validated with measured data. Various diagrams have been developed to illustrate how the properties vary with composition and temperature, including pseudo-ternary diagrams of SiO2-MgO-CaO-Al2O3 for viscosity and liquidus temperature. Models were also applied and methodologies developed to analyse historical blast furnace operations and determine target values.

Jan 1, 2011

A BRIEF DESCRIPTION OF TELPHER HANDLING AND BLAST FURNACE EQUIPMENT.The various sections will be described in the following order:(a) Telpher Handling and Storage Bins.(b) Blast Furnaces.(c) Slag Disposal.(d) Bullion Handling to Drossing Kettles.(e) Copper Drossing.(f) Copper Matte Furnace.(g) Bullion Delivery to Refinery.(h) Fume Handling.(a) TELPHER HANDLING.The telpher installation is an all-steel structure designed to carry out the work of assembly and delivery of charge materials to the blast furnaces.To simplify description, the primary telpher installation will be divided into three (3) sections:-No. 1 Section. 395 ft. long, running north and south, parallel to the water front, and so located that coke, which...

Jan 1, 1937

In blasting large tonnages of ore or material, the economy of the operation 'depends mainly on the mine manager's judgment in placing the holes to the best possible advantage and in determining the most effective size of hole to suit the conditions and requirements.The placing of holes is often looked upon as a problem involving so many uncertain factors that the application of simple mathematics is impossible. The uncertain factors arise when dealing with strata of different character, in hardness toughness and resistance to shearing.A study of the practice at many mines where all types of strata from hard ore to relatively soft overburden, and even coal, is being mined, suggests that the problem is not as complex as generally believed. There is, without doubt, some uniformity in the amount of burden given to holes of equivalent dimensions, regardless of the material being mined. The reason is simple. With too great a burden hard rock will not break out and soft rock will "bull". The nature of the strata is taken care of by the strength, quantity and distribution of the explosive charge and, to some extent, the spacing of the holes.It is because burdens are uniform in all classes of strata met with in mining, that a formula can be used to design blast hole layouts.The formula introduced in this paper is empirical as it is based on prevailing practice. It has been tested and proved remarkably accurate against every example available to the writer. Many thousands of blast holes, at many different mines, are represented by the examples given in the attached tables; to give further examples would only mean, unnecessary repetition. At the Mount Morgan Mine...

Jan 1, 1952

By Grigor Mishev, Georgi Petrov, Benjamin Cebrian

Before designing a single blast or all the blasts on a pit level, it is critical to assess the main goal on each. To do this, a series of constraints must be taken into account: wall protection, vibration control, flyrock hazards, fragmentation required, desired displacement as well as economy, equipment efficiency. The tool to do this is the Blast Master Plan. Many mines fail to integrate on its elaboration key stakeholders such as planning, operations, geology/geotechnical and milling departments. Designs not only have to provide consistent behavior of the blasts, but have to make sense all in one with the geological and geotechnical conditions as a starting point. Once blasts are designed under an organized set of priorities, and complemented with quality controls, optimization is possible on a large scale.

Jan 1, 2016

By Stephen H. Chung

The SABREX computer blast simulation program permits the study of the effective use of explosive energies and predicts the total performance of a blast in terms of:fragment size distribution: muckpile profile; breakage at grade, column and collar with respect to the control case; crack penetration; damage envelope behind and beneath blastholes; a complete cost analysis including explosives, drilling and accessory costs

Jan 1, 1995

By David E. Siskind

A Bureau of Mines survey of noise from quarry production blasting was conducted at seven crushed-stone quarries, providing information on close-in noise generation, comparative instrumentation, and evaluation of the sound levels as related to blasting parameters and existing State and local noise standards. The results from this preliminary survey will be useful in the design of a complete investigation of the problem of noise from blasting. There exists an immediate need for technical guidelines for noise pollution control agencies presently working on the regulation of impulsive noise sources. This survey and results from previous work by other researchers are used to derive interim recommendations on weighting scales, generated sound levels, and instrumentation. These recommendations are based on the limited data presently available and may be modified with subsequent investigation of noise generation, propagation, structural damage, and human tolerance.

Jan 1, 1974

By A. M. Neale

Kriel Colliery has experienced some sub-standard blast results on the overburden. Blast results are considered poor when the fragmentation is too big, back break into the new highwall, capping is experienced and/or excess overburden material is thrown into the void. Poor blasting leads to lower productivity, equipment breakdowns, and poor drilling and blasting results on the adjacent blast, contamination of coal or loss of coal. A simulation was developed in Microsoft Excel to model blasting results while changing various parameters. From the simulation results, it could be seen that a change of blast design could be beneficial. As an example, smaller drilling patterns were simulated (10 m x10 m to 8 m x8 m, and 8 m x8 m to 7 m x7 m in Pit 5 and Pit 6 respectively) in combination with changes in explosives (P700 emulsion vs. ANFO) and drill bit diameter (311 mm vs. 251 mm). The results show that each of the options has a specific scenario that will be most beneficial to the mine. These results are quite specific and subject to variable inputs. The purpose of the example is to demonstrate how the simulation can be used as a tool to asses blast design variations.

Jan 1, 2010

By Wayne Rogers, Kell Monro, Arthur Pacunana

The Phu Kham Copper-Gold Operation (PKM) is a large-scale open pit mine located in northern Laos. It was developed and is operated by Phu Bia Mining Limited (PBM) a Lao-registered subsidiary company of Australian incorporated, PanAust Limited. Production commenced at Phu Kham in 2008. Since the second half of 2016, there has been a significant increase in ore hardness and this has negatively impacted the PKM concentrator and resulted in lower SAG mill throughput rates. Over the remaining life of mine, the changing ore body and increase in ore hardness is forecast to continue as the pit deepens and the availability of softer blending ores reduce. To manage this risk, PKM initiated a Hard Ores Management Program to determine the most effective way to improve the mill throughput of harder ores. This involved conducting a number of innovative and process control driven blasting trials to optimize run-of-mine (ROM) fragmentation and other blasting outcomes. From 2016 to 2017, the performance of high powder factor blasting, electronic detonators and fast timing, high velocity of detonation (VOD) explosives, double-priming, and deck blasting, were individually and systematically assessed. The success of each blasting trial was then based on a ‘value for money’ criteria. This criteria is a cost / benefit analysis that weighed-up the additional cost to implement the trial against the measured improvement in mill throughput. Electronic and high VOD 90:10 emulsion:ANFO blasts were determined to have the best value for money, achieving an increase in mill throughput of 54% compared to baseline. This paper discusses how the implementation of an innovative and process control driven blasting trial methodology was able to successfully manage the hard ore challenges at PKM. In addition, this success was achieved without any major cost implications, safety incidents or process plant set-backs.

Jan 1, 2018

By Doug Anderson

Blast vibration seismograms are generally collected strictly for compliance with regulations. The peak levels (including dominant frequency) are typically all that are looked at. However, these records contain a lot more information about how a blast has performed. The seismogram is actually a record of explosive energy that was not used in fragmenting rock. The trick is to determine how to extract information that would be useful in analyzing blast performance.

Jan 1, 2013

By G. K. Jorgenson, S. H. Chung

"IntroductionThe SABREX Blast Modelling Program was developed jointly by the companies of the ICI Explosives Group, of which C-I-L Inc. is a member. SABREX (Scientific Approach to Breaking Rock with Explosives) is a modular computer program which incorporates new technology with a number of tested programs that have been in use world wide.SABREX predicts the performance of blasts in terms of (I) fragment size and distribution; (2) muckpile profile and face velocity; (3) grade fracture; (4) collar breakage; (5) a rupture envelope which depicts crack penetration behind and beneath blastholes; and (6) a complete cost analysis including explosives, drilling and accessory costs. The predicted blast results are displayed as dynamic colour graphics and in tabular form.SABREX uses data on the detailed geometry of the drilled and loaded pattern, detonation characteristics of the explosives and the dynamic properties of the rock to generate blast predictions. SABREX blasting calculations take into account the effects that shock and quasi-static pressures exert on the rock around the blastholes. While physical effects occur very rapidly in rock blasting, it is possible to view and model the sequence of events as discrete sections.The program can be run on a microcomputer and is currently operated by C-I-L technical service staff in Canada for the use of drilling and blasting operators.Figure I is a diagram representing the modules of the program and associated technology that is used to complement the program.Any, or all, of the modules may be used in a particular study or blast optimization. Because the BOBCAT module of the SABREX program has been described in previous papers(7.8.9), this discussion will concentrate on the newer modules: CRACK, HEAVE, RUPTURE ENVELOPE and to a limited extent, KUZ-RAM, which present a more detailed picture of the blasting process.Each of these modules is discussed in terms of the information they offer the operator in analyzing the blast. Specific examples of recent usage in Canadian mining situations are included to illustrate the ability of the model to produce practical results that can assist in optimizing actual blasting operations or solving problems that do exist."

Jan 1, 1987

By Unknown

Blast Site Security Involves: * Clearing the area * Controlling Access * Warning Signals

Jan 1, 2003

By Randall M. Wheeler

"Fourier analysis is a very powerful frequency analysis tool. However, it is frequently misunderstood and sometimes used inappropriately. Part of this workshop will involve the basics of Fourier series, the Fourier integral and finally the Fourier transform. Included will be a brief discussion of analysiswindows, including the box and Hamring windows."

Jan 1, 1998

By Gordon M. Matheson, David K. Miller

Possible impacts to the water quality and production capacity of ground water supply wells by blasting is a common cause of complaints for blasting contractors, mining companies, and local regulatory authorities. The major complaints of changes in well water quality include; turbidity, discolored water (red, brown, black, yellow and milky water), and nitrate and/or coliform contamination. The major complaints for changes in well water production capacity include: loss of quantity production, air in water and/or water lines, damage to pump, and damage to well screen or borehole.

Jan 1, 1997

By Dale Preece, Ayman Tawadrous

This paper presents a number of examples of three-dimensional blast modeling in both surface and underground environments that include time-delay explosive decking. These examples include: 1) quarry blasting, 2) coal seam protection blasting, 3) mineral mine blasting with high energy time delayed decks, and, 4) underground single-level/single-shot drawbell blasting.

Jan 1, 2014

By David Sprott, Patrick Andrieux

In 1990 the Noranda Technology Centre commenced a project to develop an interactive three-dimensional blast design system using a commercial computer-aided drafting and design package (CADD). The objective was to alleviate the blast engineer from the tedious and time consuming blast layout and design functions normally done by hand. This would allow more time for optimizing blast designs through assessing multiple options. Since several blast design software "tools" already existed at Noranda, the need arose to integrate all the applications into one overall system that shared one common database. The result is BLASTCAD.

Jan 1, 1991

By Betty J. Laswell, Gerald W. Laswell

Rotary drilling in modern open-pit mining is usually considered the lead phase which not only establishes the production rates but frequently limits them. From this viewpoint alone, the drilling phase must be maximized. The drill phase is the step that permits all the other operational phases to function within their design limits. This means that, in most cases, the drill is literally run to destruction to ensure that the shovel will be able to smoothly and consistently load a manageably size muck, the haul trucks can carry a balanced load without having a boulder dropped through the bed, and the crusher can devour constant rock size.

Jan 8, 1978

By K H. Esbensen, K Engström

The conclusion from the debate over the last decade in the mining sector is that, for grade control, reverse circulation (RC) drill sampling gives more reliable results due to less sampling problems than blasthole samples. However, by conducting the latter with well-controlled procedures there still exist fair possibilities to counteract the major blasthole sampling problems and achieve fit-for-purpose representativeness, especially if based on minimal loss of fines. In the present PhD study, extensive replicate experiments and variographic characterisations are conducted to evaluate the performance of manual blasthole (BH) sampling and sectorial segment sampling. The experiments were performed in Luossavaara-Kiirunavaara AB (LKAB)’s Leveäniemi open pit mine in the north of Sweden. The experimental area is an apatite-magnetite iron ore deposit of the Kiruna type, with the demand to exhibit a maximum of local heterogeneity to allow the experiment the largest possible conclusion powers. Gathering and splitting the complete BH drill cutting cones (fines cone, coarse cone) served as an authoritative reference on which to assess the representativity of the two BH sampling methods.Results show that manual BH drill sampling is able to produce samples with an acceptable accuracy and precision if performed properly and with insight. Based on variographic comparison, segment sampling shows similar precision for chemical grades as the manual sampling, while the particle size distributions were more deviating for segment sampling than for manual sampling at the high and low size ranges. Possible reasons for these partly surprising results are discussed.For further investigation of the performance of BH versus RC drill sampling, a second experiment has been planned on a parallel profile. This will result in an unprecedented opportunity for a full variographic comparison between RC and BH sampling, aimed at designing specific, fit-for-purpose sampling procedures as a function of ore quality, cut-off grades and important contaminant levels.CITATION:Engström, K and Esbensen, K H, 2017. Blasthole sampling (replicate and variographic experiments) in LKAB open pit iron ore mines – fit-for-purpose representativity?, Australia, in Proceedings Eighth World Conference on Sampling and Blending , pp 85–96 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017

By Thierry Bernard, Guy Gagnon

Blasting at very close proximity to urban areas is typically a situation where both local communities and mining stakeholders get nervous. The context becomes logically even more tensed when the blasting operations have to be performed above an old underground mine. When mitigating subsidence risks requires firing the largest possible shots, the nuisance control (flyrock, vibration, and noise) required by local and national regulations, contrarily urge for being more conservative.

Jan 1, 2014

By Harry Verakis, Thomas Lobb

In the past decade, approximately 5 billion pounds of explosives were used annually in the United States. Most of this quantity of explosives was used by the mining industry and coal mining was the dominant application for explosives. Considering the large amount of explosives used, the accident safety record for the mining industry has improved significantly over the past two decades. Blasting accidents are usually a small percentage of the total number of mining accidents. However, blasting accidents continue to occur and the severity of these accidents is disproportionately high with respect to other types of mining accidents. This paper is a summary and an update of the surface mine blasting accident investigations and studies conducted previously by the Mine Safety and Health Administration (MSHA) and the former U.S. Bureau of Mines.

Jan 1, 2001