Search Documents

By M. D. Khattar

The paper describes the salient construction features of the Pile foundation work for the Railway viaducts in Algeria. Six viaducts were constructed for execution of the Railway line between Aintemouchent and Benisaf in Algeria. The work was executed by the Indian Railway Construction Company Limited of India (IRCON) for the Algerian National Railways (S.N.T.F.). These six viaducts had multiple spans of 36M resting on hollow piers of heights upto 69M. Most of the piers were founded on piles of 1 and 1.2M dia bored piles going upto 22M deep through cal­careous rocks and were designed for Railway loading in seismically active area. The work involved 356 piles & constituted a very important aspect of the whole work. The concrete in the piles was made with sulphate resistant cement and the integrity of the concrete was tested with Sonic method so as to ensure the quality. The piles were driven with the help of a hydraulic oscillator and the concrete was laid with a tremie pipe. Problems as encountered during execution have been explained.

Jan 1, 1989

By Hendrick A. D. Kirsten, A. Clayr Alexander

Stillwater Mining Company is currently developing a second underground palladium and platinum mine approximately 21 km (13 miles) west of their existing Nye operation in the Bear tooth Mountains of southern Montana. Portals for the two access tunnels required at the new site were excavated in limestone talus to accommodate4.6 m (15 feet) diameter tunnel boring machines. A review of the technical design, field conditions and construction of the portals is presented.

Jan 1, 2001

By Bali. D. D., S. Chattopadhyay

"The planning and construction of prime coking coal beneficiation plants in the nationalized mines in India are reviewed. Flow schemes, construction practice, materials consumption, and costs are detailed.Medium-capacity beneficiation plants with multiple loops are recommended under Indian conditions.IntroductionThe reserve of high-grade and easily washed metallurgical coal in India are quite limited. Prime coking coal constitutes approximately 22% of the total resources and occurs exclusively in the Jharia coalfield in the state of Bihar. Bharat Coking Coal Limited (a subsidiary of Coal India Limited (CIL) the nationalized mining sector of India) owns 80% of the Jharia collieries. The development of Jharia coalfield in the pre-nationalized period before 1971 has been characterized by a large number of small mines with primitive mining methods and low productivity. The production of prime coking coal to meet the demand of the steel industry in India has to increase from the existing level of 11.1 million tonnes to 43.4 million tonnes per annum by 2000 AD, thereby producing 5.61 million tonnes and 22.7 million tonnes of clean coal respectively. An ambitious program has been undertaken for development of bigger mines with an average production of 1 to 3 million tonnes per annum. With the fast dwindling reserves of good quality coking coal, more inferior grade coal seams, having difficult washing characteristics, are now being mined. All the coal from the future mines will have to be beneficiated to make it suitable for consumption of steel plants; the following washeries are being planned for construction by 2000 AD:"

Jan 1, 1986

The principal dirnensions of the chimney were fixed as follows: Height from formation to coping, 328 ft. 8 in.; inside diameter concrete shell, 13 ft. Gin.; inside diameter of the 4~-in. brick lining. 11 ft. (j in. ; shell thickness above flue inlet at a point 39 ft. above formation, 1 ft. 8in.; shell thickness at coping, 6 in. That is, the inside of chimney is cylindrical, wldst the outside is gradually stepped inwards with of 1 in. and less until the shell is 6 in. thick only at the top. With these dimensions in mind, it will be seen that some close thought was necessary to ensure a satisfactory of fonn which could be kept rigid and plumb to a height and at the same time provide safe working conditions for the labourers employed.FOUNDATIONSThe spread base of the chimney is 45 ft. in diameter, and foundations were carried down to a depth of 8 ft. 6 in. below natural surface into good hard clay which was known to be the best foundation obtainable in the vicinity being capable of withstanding, when dry, a load of 3 tons to 4 tons per square foot, whereas dead load is 1A tons per square foot and the maximum load expeeted under the most severe wind condition is 2 tons per square foot to ensure the foundation being kept dry and unaffected by ground water, the site was surrounded by a ring drain at a distance of six feet from edge of concrete foundation and at a minimum depth of one foot below bottom of concrete. Open-jointed pipes were laid in the bottom ofthe drain and graded to a pipe drain with outfall clear of the site.

Jan 1, 1924

By Kazuo Magata, Hirohiko Fujita, Masazumi Tashiro, Yoshiaki Sato, Yoshio Shinoda

The Shinkansen of the Japanese National Railways (JNR) presently in operation between Tokyo and Hakata, approximately 1,000 km, was constructed at three stages: between Tokyo and Shin-Osaka opening in 1964, Shin-Osaka and Okayama in 1972 and Okayama and Hakata in 1975. Works on the extension of 400 km from Okayama to Hakata were launched in March 1970. As construction of the undersea Shin-Kanmon Tunnel on the extension was the toughest task, requiring many, many months, the work was undertaken earlier than any other works on the extension. It was brought to its completion in June 1974 at the cost of about 22, 000 million yen. The Shin-Kanmon Tunnel is the third undersea tunnel constructed to connect the main island of Honshu and Kyushu across the Kanmon Straits. (Table 1)

Jan 1, 1976

By Ricky Chipka, Roshan Thapa, Richard Yovichin, Greg Rogoff, Patrick Niemuth

A 4.5-mile-long, 96-inch-diameter outfall pipeline was constructed between North Texas Municipal Water District’s proposed Sister Grove Regional Water Resource Recovery Facility and the Stiff Creek Discharge Structure. Two TBM-mined tunnel segments were excavated for the outfall pipeline through rock and mixed-face conditions within the Austin Chalk Formation. The TBM mining performance was tracked in detail and evaluated during mining. This paper discusses the TBM configuration, TBM utilization, advance rates, and challenges of both tunnel segments.

Jun 13, 2023

By Zephaniah Varley, Satoshi Akai, Richard Sage, Steve Redmond, Mike Murray, Rohit Shetty, Gerald Skalla

One would be hard pressed to find another project as complex as this one given its configuration, the variety of issues to address and the required construction techniques. Contract C710 is currently under construction as part of Sound Transit’s Link Light Rail, connecting downtown Seattle with Sea-Tac Airport. The paper describes the construction-to-date of the deep mined station under Beacon Hill using the Sequential Excavation Method (SEM). This deep “binocular” station is being mined through some of the most challenging soft ground conditions in the USA. The excavated volume of the station is approximately 60,000 cy (46,000 m3) and the station comprises a variety of geometries and cross sections ranging from 235 sf (22 m2) up to 1,670 sf (155 m2). This underground complex includes platform, concourse, cross-passage and emergency ventilation tunnels together with station egress and ventilation shafts. Various excavation sequences are in use for the different tunnels including the twin-sidewall drifts for the impressive45 ft (13.7 m) wide by 42 ft ( 12.8 m) high concourse cross adits. This station has two train platforms approximately 165 feet (50m) below the surface. This station, constructed in highly variable glacial deposits including water bearing sands and silts approximately 50 ft below multiple perched water tables in an urban setting, creates a very unique and challenging situation. The ground is being managed with various types of ground improvements such as jet grouting and vacuum assisted deep dewatering wells from the surface, and from underground by use of “SEM Tool-box Items” such as barrel vault canopy, grouted pipe and rebar spiling, chemical grout,

Jan 1, 2007

By Shemek Oginski

The 5 km (16,194 lf) of 6.1m (20 ft) diameter TBM driven tunnel built by the J.F.Shea Co. will serve as sewage overflow storage. The TBM tunnel and four connecting tunnels excavated by drill and blast methods in hard granite will remain unlined. Based on the Geotechnical Baseline Report (GBR), the Contract documents provided a design with no required pattern of rock bolts, no probing, no pre-excavation or consolidation grouting, and lastly, no final lining of the tunnels was deemed necessary. This paper will provide a general overview of these topics with the emphasis on the actual ground conditions encountered versus the projected conditions provided in the GBR and how the GBR reflected the design of the project. Proposed modifications to the temporary and permanent ground support will be presented and the necessity of probing and pre-excavation grouting will be evaluated.

Jan 1, 2005

By Bob Rautenberg

The Construction of Tunnel and Edison Force Mains contract involves the installation of two new force mains to provide a redundant means for sewage conveyance from Middlesex County Utility Authority?s (MCUA) Edison Pump Station on the northern shore of the Raritan River to the Central Wastewater Treatment Plant on the southern shore. The force mains will be installed in a 1,192 m (3,910 lineal foot) long tunnel with a 4.09 m (13'-5') inside diameter, fully gasketed precast concrete segmental lining, which is to be tunneled underneath the Raritan River utilizing an Earth Pressure Balance TBM. The tunnel is anticipated to encounter flowing soils near and beneath the river. Two new 60-inch diameter Centrifugal Cast Fiberglass Reinforced Polymer Mortar force mains will be installed within the tunnel leaving an open utility corridor above the force mains for future consideration. The project also includes the design and construction of two slurry wall shafts with associated piping. The paper will provide an overview of design and provide a case history of the construction of the tunnel and highlights of the construction methods implemented to date.

By David Chastka, Isidro Rivera, Shawna Von Stockhausen, Idit Zarchi

The City of Santa Cruz Water Department is replacing the existing Newell Creek Dam inlet/outlet works at Loch Lomond Reservoir in the San Lorenzo Valley. The project will improve the City’s overall operational efficiency, improve system performance, and improve the safety and reliability of storage for the City’s drinking water supply. The project comprises new inlet works* (three new inlets that control and convey flows into and out of the reservoir, and an intake control building), an inlet/outlet tunnel with a 48-inch conduit to convey flows into and out of the reservoir, and a new outlet structure at the toe of the dam. The outlet structure includes a release point for energy dissipation of emergency drawdown flows, a connection to Newell Creek Pipeline, and beneficial releases into Newell Creek. The project also includes a new dam seepage collection and monitoring system and appurtenant structures such as a culvert bridge over the spillway plunge pool to improve access to the new outlet. Notable complex project components include in-water work to connect the new intake shaft pipes to the three new inlets. The project includes one major milestone with a work window regulated by environmental permits that could only be amended/ extended with approvals from those agencies. If not met, the milestone work would have caused significant delays (potentially up to one year) to the project.

Jun 13, 2021

By Patrick J. Doig

In mid-1991, the design/build contractor set to work on the Pergau HEP in a remote corner of Malaysia, armed with only a slim volume of conceptual drawings. The next five years saw roads, power lines, buildings, dams, and over 30 kilometers of tunnel constructed, followed by two years of E&M installation and commissioning. Along the way, the project overcame geothermal groundwater, faults, land disputes, monsoon rains, marauding tigers, and those most fearsome of foes, politicians and the press. This paper is a testament to the ingenuity, commitment, and persistence of the construction industry professionals who brought this massive project to fruition.

Jan 1, 2001

By Nicholas Tabor, Norbert Fuegenschuh, Richard Taylor, Jean-Marc Wehrli

The Plymouth Tunnel forms part of the 16-mile long route of the Purple Line Light Rail Project promoted by the Maryland Transit Administration. The tunnel is approximately 1,220 feet in length with a shallow vertical alignment located beneath a residential area. Challenging mixed ground conditions included surficial soils, decomposed Saprolite, and highly weathered to fresh rock requiring the use of the Sequential Excavation Method (SEM) for construction. This paper discusses innovative approaches implemented during construction as well as challenges faced during planning and installation of a spray-applied permanent concrete liner.

Jun 13, 2021

By Dan Martz, Bill Moler, David Young, Wally Chen, Matthew Crow, Steve Norris, Tolga Togan

Two 610 m (2000 ft) long tunnels were driven through water bearing silts, sands and clays beneath the Sacramento River using a 4.59 m (15.1 ft) diameter Earth Pressure Balance Tunnel Boring Machine (EPBM). Four sheet pile shored shafts were sunk with and without dewatering. The pre-cast concrete segmentally lined and grouted tunnels were driven down at 6% grades beneath the river flood protection levees, buildings, roads, a railroad and adjacent to a Freeway Viaduct. Details of the schedule, cost, shaft construction, TBM, tunnel construction, and installation methodology for the twin1.676 m (66 in) steel force main pipes and environmental constraints are provided.

Jan 1, 2007

By P. Perruzza, R. Grandori, A. De Biase, A. Ciamei, A. Busillo

The Turin metro alluvium soil is mainly made of large boulders, cobbles and gravel , few sand and almost no fines. This grain size curve is out of the range of application for EPB and Slurry TBMs. In order to bore 5 of the total 7,5 kms of Line 1 tunnel, two specially designed Lovat EPB TBMs were utilised in combination with a systematic non structural pre-grouting of a small volume rectangular slab just above the tunnel section. The same pre-grouting was not however applicable for lack of access on surface in some sections of the remaining 2,5 km of tunnel that had to be bored below important buildings/structures, with under ground water pressure up to 1,5 bar, with curves radius of 180 m only. For these more critical sections it was necessary to study and implement a new technical solution and improve the capacity of the TBM to work efficiently in EPB mode even in this unsuitable ground and overall conditions. After months of studies the selected and adopted solution has been to inject inside the cutterhead chamber, in addition to the almost standard foams & polymers additive mixes, a suspension of limestone powders. This with the scope of compensating the lack of fines of the natural ground with rock powders.

Jan 1, 2005

By L. L. Lacerda, A. J. Blair

The Wolf Creek Upper Narrows Tunnel (Upper Narrows Tunnel) is one of the first major highway tunnel in the United States implementing the use of spray-on membrane for purposes of constructing a double-shell drainage solution between an initial shotcrete lining and a final cast-in-place concrete lining (Figure 1). In the case of the Upper Narrows Tunnel the primary membrane is constructed with a spray-on product manufactured by Degussa, namely Masterseal® 340 FA (MS 340) that has been utilized previously in other tunnel projects. Shotcrete-like in application, but differing in physical properties, MS 340 is now outdated, and is succeeded by Masterseal® 345 (MS 345), a nearly identical product, with improvements in material properties. Tunnel project histories utilizing either MS 340 or MS 345 are discussed and summarized with regard to the respective motives for prompting spray-on membrane selection and the realized benefits resulting from spray-on membrane construction. With an emphasis on the Upper Narrows Tunnel, project summaries discuss details of the aspects of design for spray-on membrane construction methodology as opposed to conventional sheet membrane construction methodologies. It is anticipated that experience gained during the construction of the Upper Narrows Tunnel with respect to other tunnel projects that have utilized spray-on membrane will be of use for future tunnels employing spray-on membrane in drainage solutions.

Jan 1, 2005

By Kentaro Kuraji

INTRODUCTION Background Tokyo, the capital of Japan, is one of the largest cities of the world. As many as 33 million people live in Tokyo and three neighboring prefectures although the city occupies only 0.6% of the area of the country. The network of Metropolitan Expressways serves as a major artery for daily physical distribution in Tokyo. The Central Circular Route of the Metropolitan Expressway (MECCR) is located innermost among the three circular routes in Tokyo (Figure 1). Once completed, MECCR is expected to drastically mitigate traffic congestion in the central Tokyo area and provide drivers wider varieties of options in route selection. Alleviating congestion is estimated to reduce 400,000 tons of carbon dioxide emissions annually. The eastern and northern sections and part of the western section of MECCR have been completed with the total length reaching 33 km. The western section will be extended southward by approximately 4 km in the spring of 2010. An 11-km-long western section of MECCR that is currently being constructed is composed mostly of tunnels. A large number of power supply, gas supply, telephone, drinking water and sewerage pipes have been placed under the Yamatedori avenue along which MECCR is being constructed. The shield tunneling method has therefore been adopted for constructing tunnels along the route. The method involves the advancement of a shield tunnel boring machine (TBM) through the ground simultaneously assembling segmental rings within the shield. The method not only enables the building of highway tunnels more quickly and efficiently than other methods but also minimizes the effects of construction work on the surrounding area and the environment. Constructing the tunnel using the conventional cut-and-cover method might have required large amounts of time and cost because relocating the numerous objects buried under the Yamatedori avenue might have been necessary during tunnel construction. It was also considered desirable to place the tunnel at a depth of 30 m or more from surface to prevent tunnel construction from adversely affecting railways because the tunnel was expected to cross eleven railways and subways. This is one of the reasons for selecting shield tunneling as an effective method. The shield tunneling method was finally adopted for a length of 7 km in the 11-km western section of MECCR. The shield tunneling method was also employed in the Ohashi Tunnel located southernmost in the 11-km western section of MECCR. This paper describes the construction of the Ohashi Shield Tunnel.

By A. R. Dover

The Richmond-San Rafael Bridge is a 6.92 kilometer (4.3 mile) long major toll bridge span that crosses the northern San Francisco Bay in a highly seismically active region. Tutor-Saliba / Koch / Tidewater JV was contracted by Caltrans to conduct a comprehensive seismic retrofit. The JV provided geotechnical planning and quality control services as described herein, under normal oversight by Caltrans. Part of the robust foundation retrofit design included the installation of 26 new, large diameter piles, including eleven 3.81 m (12.5 ft) diameter, cast-in-drilled-hole (CIDH) marine piles that were drilled 9.15 m (30 ft) into the bedrock beneath the Bay, where the water depth ranged up to about 21.3 m (70 ft). These reinforced concrete-filled composite piles have a steel shell permanent casing from the bridge substructure pile cap through the water column and 30.5 to 39.6 meters (100 ft to 130 ft) of marine sediments to the top of rock. This paper discusses construction, inspection (ranging from the QA employed in the planning of the CIDH pile installation methods and equipment to the actual construction inspection required for the routine installation of the shafts), problems that were encountered during construction, and the solutions that were developed and implemented. Inspection, particularly with the usual difficulties in the marine environment, coupled with the difficult and complex bedrock conditions was particularly challenging, and ranged from non-destructive testing to "in-water, inshell" diver inspection. Similarly, the complexities of dealing with both the steel casing "riser" and the associated drilled shaft (rock socket) portion of these composite foundation elements created some unusual issues. The paper also presents important lessons learned from the project.

Jan 1, 2008

By Brian FitzPatrick, Michael J. Weaver

Everyone has a role in site safety, even consultants. This paper presents a summary of how a geotechnical and environmental consulting firm, with field staff on construction and subsurface explorations sites, engaged their staff and leveraged relationships with contractors to assess the construction related risks to which its staff members are exposed. These findings were then integrated into their technical training materials for both new staff and those needing a refresher, so that safety is discussed at the same time as the technical work and not treated as a separate topic. The paper outlines the process of identifying and evaluating the construction related risks that staff members face and presents examples of how the consultant can engage contractors in the process. By doing this, knowledge can be shared and there is a better mutual understanding of the risks associated with common construction and exploration related field tasks. The work resulted in an increase in staff engagement in safety, a better understanding of the true risks that staff face in the field, better relationships with contractors, and lower safety metrics. HISTORY At Haley & Aldrich, Inc., we renewed our safety journey in May 2012. Like many others, we had concerns over injuries our staff experienced in the three previous years, and a potentially significant utility strike we experienced while excavating a trench. In 2009, 2010 and 2011 we experienced an increase in recordable injuries, including two significant injuries, which caused our Experience Modification Rate (EMR) (see note below), Total Recordable Incident Rate (TRIR), and Days Away-Restricted, and Transferred Rate (DART) to rise significantly. See Fig. 1 for details. This caused us to step back and review our approach to safety, and our “safety culture”. The rise in reportable incidents and injuries also corresponded to the beginning of a growth period for the company.

Jan 1, 2019

By C N. Whata

While there is no specific obligation on the part of any applicant to consult directly with tangata whenua (people of the land), recent cases highlight the need to engage in active consultation in order to avoid serious objections and delay, particularly where a proposal may affect the matters referred to in section 6(e) (Waahi tapu/sacred places) and 7(a) (KaitiakitangaiGuardianship) of the RMA.   The Environment Court has shown some sympathy for tangata whenua where waahi tapu and other significant matters of cultural concern are at risk because of a proposed development. There are several practical steps that can be taken to minimise the potential for serious objection including: ò knowing who to contact and how to contact them; ò demonstrating empathy for the concerns of tangata whenua; ò engaging in proactive consultation, for example meeting at a time and a place that is suitable to tangata whenua, and a preparedness to meet the costs of tangata whenua etc; ò demonstrate an awareness of tangata whenua issues; being aware of the types of mechanisms that are available to remedy, avoid etc adverse effects on matters of concern to tangata whenua.

Jan 1, 1997

By X. L. Huang

This paper deals with the experimental and theoretic study of the contact pressure beneath the deep foundation of Beijing International Hotel, The experiments have been carried out in project and in model footing 6.6m2. The result of measurements shows the contact pressure at the edge is greater than that at the center. The theoretic analysis on the base of elastic theorey is in good agreement with the test if the proposed assumption used.

Jan 1, 2010