Search Documents

By Moussa Wone, Martino Scialpi, Colin LaVassar, Carlton Ray

The Potomac River Tunnel (PRT) is the next major phase of the DC Clean Rivers Program. The design-build PRT project includes a 5.5-mile-long, 18-foot-internaldiameter tunnel, seven shafts, and two underground connections to existing structures. Major challenges include tunnel boring machine (TBM) excavation though mixed-face conditions within a buried paleo-channel and an approximately 1,350-foot-long rock/ soil transition zone; construction beneath the elevated Whitehurst Freeway; tunneling beneath an existing luxury residential building and existing transit tunnels with limited clearance; and complex coordination with a variety of federal, regional, and local stakeholders. This paper describes the overall project scope, geotechnical conditions along the alignment, and primary design/construction challenges and mitigations.

Jun 13, 2021

By Gino Vogt

In mechanized tunnelling operations, performance, consumption and safety are main factors for jobsites. One of the most important components effecting these factors, especially in slurry TBM operations, are Slurry Treatment Plants (STPs). Inadequately dimensioned and designed STPs create bottlenecks for tunnelling operation and jeopardize time schedules and performance. Inefficiently planned STPs could drastically increase consumption figures such as electrical power, bentonite, water polymers, etc. Inaccurately selected and treated suspension properties can cause a high-risk potential for the whole project. This paper debates the relevant key parameters for STPs from start to finish of a project and its results in influencing factors from the manufacturer’s point of view.

Dec 1, 2022

By G. Meschke

"This paper reports on computational and experimental research, performed at the Collaborative Research Center “Interaction Models for Mechanized Tunneling” at Ruhr-University Bochum, Germany. Research covers a broad spectrum of topics relevant for mechanized tunneling in soft soil conditions. This includes advances exploration methods and models for the characterization of the in-situ ground conditions, the interaction of the face support and the tail gap grouting with the porous soil, multi-scale models for the design of fiber reinforced segmental linings with enhanced robustness, computational methods for the numerical simulation of the tunnel advancement, the soil excavation and the material transport in the pressure chamber, logistics processes and risk analysis in urban tunneling.INTRODUCTIONMechanized Tunneling has proven itself as an economical and flexible construction method that continues to undergo a dynamic evolution process. Shield diameters continue to increase, and the application range of tunnel boring machines is being extended to an ever-increasing variety of geotechnical conditions. In order to maintain economic viability and to ensure an environmentally friendly construction process, realistic and reliable numerical models are required in order to make informed decisions during planning and construction. To provide a reliable numerical prognosis, it is necessary to accurately assess and understand the interactions between the components involved in mechanized tunneling with the surrounding site, the ground, and any pre-existing structures. Heterogeneous geological conditions and often only approximated ground parameters create, in contrast to other engineering projects, special demands. This necessitates new insights to new problems that can only be effectively solved through truly interdisciplinary research. To address these challenges, the German Research Foundation (DFG) has established the Collaborative Research Center “Interaction Models for Mechanized Tunneling” (SFB 837) at the Ruhr-University in Bochum in 2010. Collaborative Research Centers are interdisciplinary scientific research groups in which cooperative research is conducted under the umbrella of a central research theme. With a research budget of ca. 10 Million Euros for the second 4-year funding period, and a research team composed of 13 project leaders along with approximately 35 scientific assistants the SFB 837 is currently one of the largest research groups conducting fundamental research in tunneling related topics worldwide.RESEARCH TOPICSThe research topics of the SFB 837 encompass a number of relevant planning and construction related aspects in mechanized tunneling (Figure 1). These research themes are each supported by computational models and laboratory investigations and are all included in an SFB overarching Tunnel Information Model (TIM). Interaction groups integrate and combine the results of different submodels through prototypical cause-and-effect relationships, and through the analysis of the Wehrhahn metro line (WHL) project in Düsseldorf, which has been adopted as the reference project for the SFB 837."

Jan 1, 2016

By Nathaniel Arbiter, Robert R. Beebe

The U.S. mining industry - once world dominant and largely independent of foreign sources for most major commodities - has today lost this position, with little likelihood of regaining it. But even though Business foretold The Death of Mining four years ago, the current outlook is less pessimistic because of drastic restructuring of the industry; a major reduction in its labor force, with resulting large increases in productivity; and introduction of improved technology. In the face of this clearly changed climate for domestic mining, it is important to examine the role of the development and research establishment in the industry's future, which raises a complex set of questions: 1. Where and to what extent can new technology assist in the continued survival of the industry ? 2. What is the past record of the research establishment in developing new technology; and what is the industry's record in supporting and adopting it ? 3. In the light of these records, and of the drastic cuts in both research staffs and expenditures, what areas should be the most important targets for new technology? New Technology vs. Old A1 though mineral processing's origins can be traced back through five or six millennia, its modern structure is about 200 years old.

Jan 1, 1989

By Jerry Williams

GEORGE WEINMAN: At this time, our co-chair, Jamie Davis from Phelps Dodge, will come to the podium. JAMIE DAVIS: Our next speaker is Jerry Williams from Phelps Dodge, Morenci. Jerry is the maintenance planning supervisor and is in charge of preventative maintenance and maintenance scheduling. Jerry's group uses predictive tools to monitor and predict the equipment failure throughout the mine, from pumps to shovels to motors, you name it. The title of Jerry's talk is "If You're Not Using Predictive Tools, You're Behind the Curve." I’ll turn it over to Jerry.

Jan 1, 1998

By Daniel Roy, Danielle Bouffard, Antoine Berton, Simon Gariépy

Commissioning a mineral processing plant has always been a challenging task. The process includes pre- operational verification, dry and wet commissioning, and a gradual ramp-up to full production, all of which must be executed within the shortest possible timeframe, requiring numerous highly interdependent tasks to be conducted concurrently. This phase is under scrutiny by shareholders, corporate management, and other stakeholders who are keen to see a return on investment as the operation starts yielding results. Despite extensive documentation in the literature highlighting its significance, the impact of the commissioning phase remains underestimated in contemporary mining projects. This paper provides an overview of the commissioning process and its associated challenges before focusing on a critical success factor: building a dedicated commissioning team with the required competencies and personality profiles. The roadmap to achieving an efficient plant start-up is outlined. Drawing on over 15 years of experience with more than 20 concentrator commissioning and start-ups, a general framework is presented to maximize success. This method emphasizes the crucial role of the operation and metallurgy team in supporting these projects. Finally, insights from Soutex’s involvement in multiple start-ups are shared, offering lessons learned that emphasize best practices and challenges encountered in expediting the ramp-up process while maintaining high Health, Safety, and Environment (HSE) standards.

Feb 1, 2025

By P. K. Kankar, Manoj Khandelwal, Ramesht Shukla

One of the utmost severe mining catastrophes in underground hard rock mines is rock burst phenomena. It can lead to damage to mine openings and equipment as well as trigger accidents or even threat to life as well. Due to this, a number of researchers are forced to study some easy-to-use alternative methods to predict the rock burst occurrence. Nevertheless, due to the extremely multifaceted relation between mechanical, geological and geometric factors of the mines, the conventional prediction methods are not able to produce accurate results. With the expansion of machine learning methods, a revolution in the rock burst occurrence has become imaginable. In present study, three machine learning methods, namely XGBoost, decision tree and support vector machine, are utilized to predict the occurrence of rock burst in various underground projects. A total of 134 rock burst events were gathered together from various published literatures comprising maximum tangential stress (MTS), elastic energy index (EEI), uniaxial compressive strength and uniaxial tensile stress (UTS) that have been used to develop various machine learning models. The performance of machine learning methods is evaluated based on the accuracy, sensitivity and specificity of the rock burst prediction.

Mar 17, 2021

By G. van Eck, H. Smit, L. Meyer

The Cook Islands (CI) possesses within its Exclusive Economic Zone (EEZ) a massive field of polymetallic nodules representing one of the world’s largest undeveloped cobalt deposits, along with large quantities of other metals critical to achieving global energy transition targets. In February of 2022 the Seabed Minerals Authority (SBMA) of the CI granted Moana Minerals a license to conduct our nodule exploration program. This paper describes how Moana Minerals chose to approach conducting exploration activities, one of the greatest challenges to Deep Sea Mining (DSM) development and the securing of the social license to advance to eventual mining of the resources, in an unconventional manner. The remote location of the project poses logistical challenges in mobilizing to and operating in the region and is a significant cost driver. Historically, exploration campaigns mobilized large vessels from mainland Europe, the Americas, and Asia as this model works well when contemplating long duration and widely temporally spaced campaigns without the need to revisit. Moana Minerals, when considering these challenges determined a multi-year deep sea mining (DSM) exploration program conducted in such a remote location can be better optimized by the deployment of a smaller yet highly capable “exploration optimized” vessel that is dedicated to the task and is based full time in the Cook Islands. INTRODUCTION The paper describes the challenges of exploration in remote regions including the South Pacific, and how an unconventional consideration of the problem led to the solution. Completion of an Environmental and Social Impact Assessment begins with a detailed environmental scoping study, resource update sampling requirements, and engineering data and sample requirements, which identifies the exploration goals of the project and technology needed to accomplish those goals. The method walks the reader through vessel and technology selection, discusses the challenges of equipment selection considering size and capability, describes the final arrangement, and provides results from the initial exploration campaigns. We followed the project from conception through the shipyard conversion, mobilization, and initial operations in the Cook Islands. The result shows how a smaller vessel with limited budget makes a large impact on the exploration capabilities in the region while building public trust. The Anuanua Moana is the first dedicated deep sea minerals exploration vessel modified with a suite of technologies that allow it to compete technically with existing ships but operate locally in the smaller ports of the South Pacific. The unique combination of size and technical capability gives the Anuanua Moana advantages over other vessels. This paper shows the importance of the Anuanua Moana in the development of offshore exploration strategies in the emerging deep sea minerals space.

Feb 22, 2026

By Daniel Saint Don, Jacques Dumouchel

QIT Madagascar Minerals (QMM)’s heavy mineral sand deposit located near the Village of Fort Dauphin, Madagascar was recently drilled using Boart Longyear Company’s Mini-Sonic drill. Continuous sand core samples were obtained to a depth of up to 30 meters for analysis and compared with the existing drilling data. Results were used as part of a validation process of the resource estimate, based on approximately 1,500 exploration holes drilled to date.

Jan 1, 2005

By Minggao Qian, Jialin Xu, Wenqi Lai, Weibin Zhu

This article advances an innovative concept explaining the connotation and technical system of "green" mining. The important theoretical foundations of "green" mining are the distribution and development characteristics of joints, fractures and bed separations, and the seepage and flow behavior of methane and water in the broken rock strata following coal mining. The main focus of "green" mining technique includes water-preservation in mining areas, coal mining under buildings with bed separation spaces grouted to retard surface subsidence, partial extraction and backfill mining, simultaneous extraction of coal and coal-bed methane, coal roadway supporting and underground disposal of rock waste, underground coal gasification, etc.

Jan 1, 2005

By G. Krogman, C. Walla, B. Wood

The Gebo Mining District (District) is located in the Bighorn Basin of Wyoming. Commercial underground coal mining began in 1906 with the arrival of the railroad in Thermopolis, which is located approximately 11 miles to the south. Mining in the District ceased by the early 1970’s. In Fall of 1999, Lidstone and Associates, Inc. (LA) and their subcontractors were retained by the Wyoming Abandoned Mine Land Division (WyAML) to perform an inventory of over 500 abandoned mine sites across Wyoming. During the summer of 2000 field inventory, a 30-foot deep headcut (Figure 1) and sink-hole were noted in the West Fork of Sand Draw (WFSD), immediately west of the Town of Gebo. The headcut and sink-hole were located at the culvert outfall associated with a stream crossing of a relatively well traveled county road. Upon further investigation, it appeared that underground mine workings had been exposed at this location. This resulted in a condition whereby water would be conveyed directly into the mine workings during a runoff event. The exposed mine workings as well as stream capture created a very hazardous condition. The WyAML implemented mitigation measures in the summer of 2000 by constructing a temporary stream crossing upstream of the existing failed crossing. To address this hazardous situation as well as a number of other hazards identified in the District during the field inventory, the WyAML retained PHC Reclamation, Inc. (PHC). PHC was directed to perform a field investigation and develop a Reclamation Plan to address all existing abandoned mine hazards in the District. Federal, state, and private parties own lands within the District. Hazards identified during the investigation included an underground mine fire, open adits, open shafts, subsidence, drainage problems, and coal slack. A Report of Investigation (ROI) was submitted to various regulatory agencies that documented the existing conditions and conceptual reclamation plans to remediate the hazardous conditions. After review of the ROI by the US Department of Interior - Bureau of Land Management (BLM) an on-site meeting was conducted. BLM Cultural Resource personnel declined to approve a District reclamation project until a historical overview of the entire District was prepared. Due to the hazardous situation associated with the WFSD stream crossing, Hot Springs County Road and Bridge Department convinced various state and federal regulatory agencies to allow reclamation of the stream crossing to occur. A decision was made to allow reclamation on privately owned lands within the WFSD drainage. This decision limited the amount of channel that could be subjected to reclamation upstream of the crossing to privately owned lands. PHC contracted LA to perform a geologic, geomorphic, hydrologic, and hydraulic investigation of the drainage to assist in the development of a WFSD reclamation plan. LA’s investigation consisted of four parts: Delineate the extent of mine workings in the area; Identify all drainage structures that required mitigation; Survey a series of channel cross-sections and a longitudinal profile of the impacted channel; and, Develop basin hydrology to assist in the design of a stable reclaimed stream channel.

Jan 1, 2006

By J. Walden, S. Rhoades, R. E. Miller, R. Gibbs, P. Boman

Accelerometers and pressure transducers mounted in suspension components can be used to monitor the ride of haulage trucks. Presently, it is difficult to tell what caused a jolt to the truck using either pressure or acceleration data alone. When information from a Global Positioning System is recorded at the same time as shock pressures or acceleration data, then the exact location of an event can be determined. Mine management can then determine what caused the jolt to the truck.

Jan 1, 1999

By K. Awuah-Offei

The objective of asphalt mix design is to produce a mix with optimal performance using available aggregate stockpiles. Often, this process does not take into consideration aggregate plant stockpile inventories or the cost of aggregate in the mix. This is due to the lack of tools that enable the lab technician or the engineer to optimize the mix for good performance while reducing the cost of aggregate and managing the stockpile inventory levels. The Bailey method provides useful guidance on aggregate gradation selection for optimal performance. This work presents a linear programming model of the asphalt mix design problem. The algorithm is implemented in MATLAB as an Asphalt Mix Design Optimization (AMIDO) program. The program is successfully validated with real-life data. The results show that AMIDO can be used to successfully produce any mix design with known Bailey method ratios. Also, RAP can be included in a design easily by making use of the Bailey method ratios and AMIDO. This work improves the state-of-the-art in asphalt mix design for dense graded mixes and could potentially be modified for other mixes.

Jan 1, 2009

By B. K. Belle

The beginning of 21st century has heralded the global strategic importance, as evidenced by increase in energy prices and energy generation-emission-utilization dilemmas. In January 2008, the South African energy supplier, ESKOM had tabled the concept of power conservation and acknowledged the energy crisis until 2016. The concept is required of all energy users to reduce their electricity consumption, intensify energy efficiency and cautiously proceed with new projects. The generation of energy results in by-products called ?green house gases? (GHGs). To make a positive response to climate change and their effect on the environment, every energy user must ensure efficient energy use through technical and administrative means referred to generally as energy savings. This paper identifies mine ventilation engineering, in particular the electricity consumed by main fan units, as an area of potential energy savings. For a major mining company, electricity consumed by main ventilation fans alone can be in the order of 120 MW. Although a known fan engineering technique but scantly applied technology identified as the Hermit Crab can be seen as a ?quick win? project, due to its success in other industries such as cement and steel. The ?Hermit Crab? technique® involves upgrading or replacement of an impeller - whatever its origin - with a design impeller to suit the actual ventilation requirements, resulting in increased fan efficiencies. The cash flow benefits associated with a case study and its rollout of this technology have been calculated. For a 10% increase in main fan efficiency, would have a net present benefit of US$ 16.08m over 10 years. With the inclusion of carbon credits, this benefit rises to US$ 29.40m in total. Application of other available technologies, viz., composite materials, ventilation-on-demand and variable speed drives are discussed.

Jan 1, 2009

By A. Farnoud

Thousands of miners, construction workers, and truck drivers are exposed to diesel exhaust particles. Diesel Particulate Matter (DPM) is a probable human carcinogen and stringent occupational and environmental standards have been established or are planned worldwide. Modifications in fuels and diesel engine designs have reduced emissions, but may not be enough to comply with the tightest standards. Post-combustion aftertreatment devices are likely necessary for many engine operators. However, even the most common and well studied aftertreatment devices fail from time to time. The objective of this study was to design, construct, and test an electrostatic aftertreatment device to treat DPM. An electrostatic precipitator (ESP) was designed and constructed to capture DPM from diesel exhaust, and different configurations were tested to optimize its performance. DPM was produced by a 6 kW diesel-powered electric generator and directed to the ESP through a short section of galvanized steel pipe after the muffler. Number and mass removal efficiencies were measured with a condensation particle counter (CPC) and by sampling through a stainless steel cassette and collecting the DPM on Teflon filters. Particle size distributions were measured with and without control using a 6-stage cascade impactor. The experiments were performed with the engine running at idle and also at medium load. The results show that our first generation ESP provides 60 percent mass removal efficiency, and up to 80 percent number removal efficiency. Power consumption was generally low, about 20 to 30 watts, to achieve these levels of performance.

Jan 1, 2009

By S. C. A. Franca, M. T. Millqvist, A. B. Luz

Laboratory experiments were performed on a Brazilian diatomite from Bahia State to produce an industrial product for use as a filter aid. Bench and pilot plant tests were conducted consisting of: diatomite desegregation, organic matter and clay removal, filtration, drying and calcination. Calcination temperature and sodium carbonate addition influenced diatomite particle size distribution. Optimum filtration rates for calcined products were obtained at 900°C and 47 min. residence time with 3% (w/w) of sodium carbonate addition, and resultant products met specifications imposed on filter aids.

Jan 1, 2002

By Donald P. Richards

Is a shaft the same as a tunnel and can it be approached in the same manner for design and construction? The most obvious difference between a shaft and a tunnel is that of orientation; whereas a tunnel is commonly near horizontal or slightly dipping, a shaft is commonly vertical or steeply inclined. As a result, design and construction methods employed for tunneling, in general, cannot be directly applied to shafts, although some of the basic concepts of behavior are quite similar. Many of the shafts that have been sunk in various parts of the world are owned by private mining companies. Each company has generally accumulated years of experience in shaft sinking and mining techniques pertinent to its particular geographic location. When a new shaft is to be sunk or an existing shaft deepened, the tendency often seems to be to continue to use the methods that have been used successfully in the past.

Jan 1, 1979

By Adrian Coombs, Paul Magowan, Derek Zoldy

Continued development and intensification are fuelling the urgent need for new trunk infrastructure within The Regional Municipality of York and throughout the Greater Toronto Area. Permitting of these projects is increasingly subject to public scrutiny to severely restrict dewatering through construction technologies and the requirement for a comprehensive and effective Environmental Management Plan. Three current projects: one on the York Durham Sewage System and two in the City of Toronto 1.Conventional Design, Tender, Award: 4,150m (13,600 ft.) 2.7m (9 ft.) finished interior diameter soft ground tunnel for York Region’s YDSS Interceptor Trunk Sewer 2.Negotiated Contract: 3,800m (12,500 ft.) 3.5m diameter (11.5 ft.) rock tunnels for Enwave’s environmentally sustainable and innovative chilled water system in downtown Toronto 3.Conventional Design, Tender, Award: 2,200m (7,200 ft.) 3.3m diameter (10.8 ft.) rock tunnel for reinforcement of Hydro One’s primary hydro feed in the downtown core of Toronto These projects exemplify issues such as: EPB tunnel and sealed shaft technologies Substantial permitting requirements associated with dewatering Mitigation of rock creep Congested downtown rights-of-way Deep shafts and confined working compounds Unique scheduling and cost benefits when Owner, Contractor and Consultant can work together cooperatively.

Jan 1, 2007

By David Smith, Bernie Martin

The Queens Bored Tunnels consist of 11,000 feet of 19'-6" inside diameter tunnels mined through rock, mixed face and dense glacial till, constructed with bolted gasketed one pass reinforced concrete liner. The tunnels are to be excavated with a pressurized face TBM, either EPB or slurry. The construction of the tunnels will require ground stabilization in the mixed face area, instrumentation and monitoring of railway infrastructure, underpinning of bridges, relocation and protection of utilities, demolition of some industrial buildings, construction of open-cut approach tunnels and emergency exits and vent plants. The purpose of this paper is to describe the scope of work, the suggested methodology and the proposed construction schedule.

Jan 1, 2005

By C. S. Davis

In being asked to present this paper on the improvements in loading and hauling equipment and the effect on unit costs, Mr. Van De Water, your program chairman, stated that his reason for coming to a contractor was due to the wide experience of, and I quote: "a large contracting firm using a variety of equipment on varying types of earth moving jobs." We people in Utah Construction Company are flattered that Mr. Van De Water singled out our Company for this assignment. Utah Construction Company's participation in open pit mine stripping antedates the 1920's, when overburden was being removed from copper ore in Bingham Canyon, Utah. Our first stripping con¬tract for the Copper Company was finished in 1912. Since that early beginning, Utah has, as a contractor, been engaged to strip and mine iron ore properties, coal properties, copper properties, uranium properties, phosphate,-gypsum, limestone and dolomite properties. And, as you know, the Company has become a major producer of iron ore from Company-owned open pit mines. Utah Construction Company has been instrumental in the evolution of open pit mining tools. Some of the first tools were the old wood and coal fired stream shovels which had to be fired hours before a shift started to insure a full head of steam, providing power to excavate with the then large 1-1/2 cubic yard buckets. Today, Utah's strip mining is done, with 18 cubic yard and 10 cubic yard crawler shovels. Yesterday's horse and mule drawn, iron wheeled wagons, with 1 and 2 cubic yard capacity, which were hand dumped by removing the false bottom, one 2 x 4 at a time, have been replaced by today's- 50-ton capacity, hydraulic, rear dump trucks and giant 40-ton coal haulers. Utah Construction Company used the early fresnes and wheeled scrapers which were horse and mule drawn. Often, an operator holding too tightly to a handle was thrown into his horses when a hard spot turned the scraper, a contrast with today's 20 and 25 cubic yard, self-powered diesel and diesel electric Gargantuan rigs; with power controls that relieve the operator of practically all physical work. This Company has pioneered many of today's advances in equipment with shop made prototypes, features of which were adopted and elaborated upon by equipment manufacturers.

Jan 1, 1959