Search Documents

The purpose of this study is to formulate practical guidelines for active underground mining in close proximity to water bodies. This was accomplished through systematic completion of three phases of study: I) Collection and Documentation of Data; II) Application of Existing Guidelines to Case Histories of Previous Inundations; and III) Development of Recommended Guidelines for Underground Coal Mining Near Bodies of Water. Phase I of the study involved a worldwide data collection effort designed to obtain foreign and domestic guidelines for mining near water bodies, and accident records and case histories of accidental mine inundations. Within Phase II, existing guidelines were categorized and classified and then evaluated as to their effectiveness in precluding past inundations had they been in effect at the time of inrush. Advantages and disadvantages of existing guidelines were defined. Drawing on the broad data base established in previous study efforts, Phase III was directed at development of viable guidelines to promote the greatest possible coal extraction while precluding accidental mine inundation. Two levels of guidelines are presented; Level I Guidelines require little or no subsurface exploration on the part of the mine operator, while Level II Guidelines recommend various testing and investigative procedures to permit greatest possible mineral extraction. This report presents findings and conclusions of the study.

Jan 1, 1976

By William H. Langer

The annual consumption of sand and gravel aggregate in 2006 in the Phoenix, AZ metropolitan area was about 76 Mt (84 million st) (USGS, 2009), or about 18 t (20 st) per capita. Quaternary alluvial deposits in the modern stream channel of the Agua Fria River west of Phoenix are mined and processed to provide some of this aggregate to the greater Phoenix area. The Agua Fria drainage basin (Fig. 1) is characterized by rugged mountains with high elevations and steep stream gradients in the north, and by broad alluvial filled basins separated by elongated fault-block mountain ranges in the south. The Agua Fria River, the basin?s main drainage, flows south from Prescott, AZ and west of Phoenix to the Gila River. The Waddel Dam impounds Lake Pleasant and greatly limits the flow of the Agua Fria River south of the lake. The southern portion of the watershed, south of Lake Pleasant, opens out into a broad valley where the river flows through urban and agricultural lands to its confluence with the Gila River, a tributary of the Colorado River.

Jan 2, 2010

By AIME AIME

TRANSFER to the Bureau of Mines of the responsibility for conservation and production of helium, and announcement that a proposal has been made to the President for commercial operation of the Los Angeles has attracted new attention to the helium program of the Government. The matter is one in which mining engineers, and the mining industry in general, have a peculiar interest. Helium is a byproduct of the petroleum and natural gas industry. It is found in certain of the natural gases which have themselves been discovered, in the main, in the search for oil. If it is to be produced on a large scale, the conservation and development of the fields will necessarily be done by the men of the oil and gas industry. There is no known or expected source of supply of quantities of commercial importance save in the natural gas fields. Not all gas wells supply helium and none of them supply it in important percentages. If it were necessary to prospect a field, develop it, lay pipe lines and build production plants for the helium alone, the cost would be prohibitive. On that basis helium would necessarily be restricted to essential war uses, where cost is subordinate to need. As a byproduct of the natural gas in certain, at least, of the fields in the United States there is distinct reason for anticipating that it may be produced in amounts and at a cost that will permit its regular use in commercial airships.

Jan 1, 1925

By A. J. Stewart, M. Guay, J. W. Critchfield, A. P. Hoddeson

The MetroWest Water Supply Tunnel project includes three main work shafts, excavated primarily in rock. Shaft L is 9.8 m (32 ft) diameter and 124.1 m (407 ft)deep. Shaft E is 7.0 by 12.8 m (23 by 42 ft) and 91.4 m (300 ft) deep. Shaft 5A is 7.9m (26 ft) diameter and 72.5 m (238 ft) deep. Construction methods are compared and contrasted. Lessons learned involve a differing site condition in soil overburden, contractor-proposed modifications, and remedial slurry wall work. Other aspects discussed include noise and vibration control, groundwater inflow, water treatment, muck handling and contract administration issues.

Jan 1, 1999

Surface mining and reclamation of a southeastern Ohio site with sandstone-shale overburden resulted in (as compared to premining levels): 1) runoff volumes and peak rates that increased by a factor of from 2 to 10 during mining and after reclamation, 2) destruction of the "aquifer" perched on the underclay of the mined coal bed and gradual, but, as yet incomplete redevelopment of this aquifer after reclamation, 3) no immediate effect on another, lower perched "aquifer", 4) up to 100 times greater sediment concentrations in runoff. Results were influenced by increasing annual precipitation amounts through the period of record; 1978, 1979, and 1980 (postreclamation years) experienced precipitation amounts approaching or exceeding long-term normalcy for the area. Part of the reason that the site produced more runoff after reclamation than before mining is that the premine condition was one of an open, porous soil under woodland, while the postreclamation condition was one of a compacted, bulldozed soil. Sediment concentration results were influenced by failure of the postreclamation erosion control system and by a series of detention reservoirs above the stream monitoring station.

Jan 1, 1983

By Rajiv Kalra, Ji Jiangang

"This paper reviews the following aspects of the world’s largest manufactured Grinding Mill’s in terms of diameter and power, along with the world’s biggest shop assembly and trial run of the mills delivered to Sino Iron Magnetite Project in Australia.1. An overview of the basic flow sheet of the Sino Iron (Magnetite) Project located in Australia2. An overview of in-house designed CITIC Heavy Industries 12.2 m (40ft) F x 11 m(36ft) LG – 28MW AG mills including FEA and major components3. In-house manufacturing at CITIC-HIC work in Luoyang China of all major components for 6 off Ø12.2 m(40ft) AG mills and 6 off Ø7.9 m(26ft) x 13.6 m(44.6ft) LG – 2 x 7.8 MW Ball Mills4. Major aspects of design and preparation of the biggest shop trial run of Ø7.9 m(26ft) x 13.6 m(44.6ft) LG Ball Mill witnessed by international EPCM’s and clients in July 2009.5. Major aspects of one piece assembly of 1300 tonne rotating element of the Ø12.2 m(40ft) x 11 m(36ft) LG AG Mill and Ø7.9 m F (26) x 13.6 m(44.6ft) LG Ball Mill at the port of the export China and transport to Australian Port and then to site.6. An insight to unique installation methods used for Ø12.2 m(40ft) and Ø7.9 m(26ft) rotating element lifting on the mill foundation in one piece assemblies.7. CITIC Heavy Industries present capability for in house design and manufacture of Grinding Mills up to Ø13.7 m (45 ft) with 35 MW Gearless drives and Ø12.2 m(40ft) with 2 x 10 MW Geared Mill drives"

Jan 1, 2012

By Janne P. Isohaka, Anssi M. Laaksonen

"Abstract In Scandinavia the use of steel pipe piles in bridge foundations started in the mid-1980s and has increased steadily since. As the piles driven in soft soils are slender, they can fail by buckling. Buckling usually requires taking into account the second order effect in structural and geotechnical design.The purpose of this paper is to derive formulas for demonstrating the theory behind the formulas given in literature for the second order effect of initially bent piles.IntroductionIn Scandinavian countries solid bedrock usually lies at moderate depth. If the bridge site is in an area where the soil above the bedrock is soft, the bridge is usually founded on end-bearing piles resting on the bedrock.The main purpose of the piles is to transfer axial forces into bearing soil. Like columns, piles can lose their stability by buckling when surrounded by soft soil. When axial compression on a slender, initially straight, pile reaches a particular value called the critical load, the pile is subjected to lateral deflection and loses stability. The soil around the pile suffers a corresponding deformation. This soilstructure interaction increases the critical load compared to a pile without surrounding soil.It is very unlikely that piles are ideally straight. Initial curvature along with curvature and deviation caused by the installation of piles causes bending moments to the pile when normal force is applied. These lateral displacements increase when normal force increases. This increase of moment is called asecond order effect.Eurocode and literatureEurocode 7 includes guidelines for the design of piles (Eurocode 3, section 5 includes design of steel piles). However, there are no clear guidelines for considering the second order effects related to piles surrounded by soil. Eurocodes advise doing structural design of piles the same way as in the case of columns. With columns, the second order effect is taken into consideration by multiplying the first order moment with the factor shown below (SFS EN-1992-1-1, 2005):"

Jan 1, 2014

By Frederic P. Dewey

(New York Meeting, February, 1912.) By the old method of determining platinum in ores and bullion, the silver-alloy first obtained in the regular course of assay is parted in strong sulphuric acid and the residual metal weighed. This is re-alloyed with silver by a second cupellation and parted in nitric acid, the residual metal being again weighed. Any difference shown between the two weighings is assumed to be, and is called; platinum. Sometimes it is so, and if any considerable amount of platinum be present, there will be a decided difference between the two weighings; but a slight difference is no real evidence whatever of the presence of platinum. On the other hand, the second weight may equal or possibly exceed the first, even when traces of platinum are present. Again, other members of the platinum group may go into solution in nitric acid more or less. If present, these would be called platinum and escape detection. The method does not provide any direct tests whatever as to the presence or absence of platinum. It is often indecisive, and sometimes jives erroneous results. It is, therefore, quite unsatisfactory. Being called upon many times to determine platinum in a wide variety of materials, particularly when present in very small amounts, I have realized the disadvantages and defects of this old method. In an article on the solubility of gold in nitric acid, 1 I have briefly outlined a method of gathering a little gold out of a solution containing much silver, which furnishes the basis of

Apr 1, 1912

By Wittenberg J. C, Reid A. F

A method is described for the rapid and effective production of polished section mounts of ore and mineral particulates to the standards required for automated image analysis. This requires mounting without segregation of particles by mass or density, and it is also preferable to avoid having particles in contact so that they can be recognised as individuals. To achieve this, the particle samples are first split to an appropriate degree in a rotary riffle, and the sub-sample mechanically diluted and thoroughly mixed with an inert filler of the same size range as the particles. Just sufficient epoxy resin is added to make the mixture fluid. During setting, the ore particles are mechanically supported by the inert filler particles, thus maintaining the particles in a random three-dimensional distribution. A rapid two-stage grinding process, based on the successive use of 600 mesh silicon carbide and 1200 mesh (10 um) corundum on cast iron plates, is followed by three stages of mechanical diamond polishing on cloth laps. Hand polishing is entirely avoided, as is the use of papers.

Jan 1, 1984

By AIME AIME

THE 123d meeting of the Institute was held in New York Feb. 14 to 17, 1921. The total registration was 1199, as compared with 1138 at the New York meeting in 1920. The weather was a strange and welcome contrast to that of last year, when New York was buried under six feet of snow as the result of the fiercest blizzard in its history. This year there was no snow, and the weather was said to be much more like an Arizona winter than New York. A complete program of the Technical Sessions is on p. 9. The discussions of the papers presented will be published in pamphlet form as soon as possible and will be noted in MINING AND METALLURGY in the usual way.

Jan 1, 1921

By Bo Björkman

A controlled dust generation whereby the dust generated would be enriched with specific metals would considerably facilitate the possibilities of recovering metals from such dusts. A basic understanding of the dust forming mechanisms is of fundamental importance to achieve a controlled dust generation. The present study deals with dust formation in a copper converting process. Dust samples collected from various places in the gas cleaning system were characterised for chemical and mineralogical composition using chemical analysis as well as microprobe analysis. Thermodynamic calculations were used to predict the formation of chemically formed dust at various temperatures and amounts of leakage air to the gas system. The results show that a separation of mechanically formed dust. e.g . Si0:2. Cu and chemically formed dust. e.g .? Ph, Zn, As, Bi. could, to some extent, be obtained due to their different particle sizes. A selective condensation of Pb, Zn and As at various temperatures could. according to thermodynamic calculations, he possible at high temperature. A selective condensation of metals requires an airtight gas cleaning system or a gas cleaning system with a limited amount of leakage air in order to maintain the desired temperature level.

Jan 1, 1996

By Rajiv Kalra

This paper reviews the following aspects of the world?s largest manufactured Grinding Mill?s in terms of diameter and power, along with the world?s biggest shop assembly and trial run of the mills delivered to Sino Iron Magnetite Project in Australia. 1. An overview of the basic flow sheet of the Sino Iron (Magnetite) Project located in Australia 2. An overview of in-house designed CITIC Heavy Industries 12.2 m (40ft) F x 11 m(36ft) LG ? 28MW AG mills including FEA and major components 3. In-house manufacturing at CITIC-HIC work in Luoyang China of all major components for 6 off Ø12.2 m(40ft) AG mills and 6 off Ø7.9 m(26ft) x 13.6 m(44.6ft) LG-2 x 7.8 MW Ball Mills 4. Major aspects of design and preparation of the biggest shop trial run of Ø7.9 m(26ft) x 13.6 m(44.6ft) LG Ball Mill witnessed by international EPCM?s and clients in July 2009. 5. Major aspects of one piece assembly of 1300 tonne rotating element of the Ø12.2 m(40ft) x 11 m(36ft) LG AG Mill and Ø7.9 m F (26) x 13.6 m(44.6ft) LG Ball Mill at the port of the export China and transport to Australian Port and then to site. 6. An insight to unique installation methods used for Ø12.2 m(40ft) and Ø7.9 m(26ft) rotating element lifting on the mill foundation in one piece assemblies. 7. CITIC Heavy Industries present capability for in house design and manufacture of Grinding Mills up to Ø13.7 m (45 ft) with 35 MW Gearless drives and Ø12.2 m(40ft) with 2 x 10 MW Geared Mill drives

Jan 1, 2012

By Matthew Preedy, Brett Campbell, Jim Rush, Alan Howard, Derek Penrice

All Rights Reserved. Printed in the United States of America. Information contained in this work has been obtained by SME, Inc. from sources believed to be reliable. However, neither SME nor its authors guarantee the accuracy or completeness of any information published herein, and neither SME nor its authors shall be responsible for any errors, omissions, or damages arising out of use of this information. This work is published with the understanding that SME and its authors are supplying information but are not attempting to render engineering or other professional services. If such services are required, the assistance of an appropriate professional should be sought. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of the publisher. Any statement or views presented here are those of the authors and are not necessarily those of SME. The mention of trade names for commercial products does not imply the approval or endorsement of SME.

Dec 1, 2018

By Michael E. Zellars

The distribution of phosphate in Pliocene-Miocene deposits of the Southeastern United States was controlled by the prevailing geologic setting. For each basin a unique set of conditions in terms of relationship of land mass to shelf, depositional environment and seawater composition, and movement controlled phosphate distribution. Concentration sufficient to recognize the deposits as a resource occurred in lagoons or shallow neritic zones, with clastics and carbonates diluting the section basinward. Each deposit within a basin displays similar metallurgy and lithology, notwithstanding post-depositional alteration.

Jan 1, 1978

By Mohsen Mohammadi, Edward Cyr

"To date, several studies have been performed on the static mechanical properties of SLM-AlSi10Mg alloy. There have also been more recent studies on the relation between scan strategy, texture, and mechanical properties of SLM metals and composites. However, there is a huge knowledge gap in the available literature regarding texture and mechanical behavior of SLM-AlSi10Mg alloy under high strain rates. Therefore, in this study, dynamic mechanical behavior of AlSi10Mg_200C alloy manufactured by DMLS technique was investigated at high strain rates ranging from 900/s to 1700/s using Split Hopkinson Pressure Bar. Texture using X-ray diffraction technique of the initial samples were measured. The yield strength, peak flow stress, and ductility increased in all samples with increase of strain rate. TEM studies have also revealed evidence of continuous dynamic recrystallization in grains after 900/s–1700/s strain-rate tests. A Taylor polycrystal crystal plasticity constitutive model was then developed to capture and predict the texture evolution and mechanical response under dynamic loading, using plastic work as a critical parameter for the onset of recrystallization.INTRODUCTION Additive manufacturing (AM) powder techniques are among the fastest advancing breakthroughs in manufacturing in recent years, defined by a bottom-up layer by layer process of joining with energy input from lasers or electron beam (Herzog et al., 2016; Gibson et al., 2015). Among alloys fabricated by SLM, AlSi10Mg is of high interest to industry and academia due to its low density, high specific strength and excellent corrosion resistance, making this alloy a viable contender for aerospace, automotive, and marine applications. Circumstances such as car crash or bird aircraft strike hazards subject potential additively manufactured AlSi10Mg parts to impact loadings. This drives an interest in understanding and predicting dynamic behaviour of these alloys. AlSi10Mg is the AM counterpart of A360 die-cast aluminum, which possess hypoeutectic microstructure (Li et al., 2015). Up to the present time, many studies have presented the mechanical properties of SLM-AlSi10Mg alloy. The mechanical properties and microstructure of AlSi10Mg produced by selective laser melting (SLM) or DMLS techniques can be controlled using different parameters, such as feedstock powder (Asgari et al., 2017), and process parameters (Olakanmi et al., 2015). The microstructure and mechanical properties of AlSi10Mg can also be controlled using post heat treatment after SLM process Li et al., 2016). The mechanical properties of SLM-AlSi10Mg are sensitive to strain rate and can both change under quasi-static (Rosenthal et al., 2017) and high strain rates (Asgari et al., 2018). However, a significant knowledge gap in available literature regarding modeling these behaviours, and especially micromechanical modeling of dynamic behaviour."

Jan 1, 2018

By Albaharna O. T., Argyropoulos S. A.

"This paper describes the development and the implementation of process control in a variety of instruments used in metallurgical laboratories. These instruments are used for different research projects in extractive metallurgy. Hardware and software aspects for this implementation are described and analyzed. Extractive metallurgy applications where process control was .used are presented. IntroductionMicroprocessors are invading almost every area of our lives and are turning up in unexpected applications. A great deal of new equipment which is coming into the market have built- in microprocessor systems. Nevertheless, the area of upgrading existing processes has been slow to develop. There are a variety of reasons for this, and many of these are economic. One of the principal reasons, however, is the general reluctance on the part of many organizations to commit a strong effort to put this new technology into their existing processes.Microprocessor systems developed ""in lab"" are capable of not only measuring thermophysical events which are taking place in metallurgical furnaces, but simultaneously controlling these furnaces. In this paper software and hardware aspects in the implementation of microprocessor control for resistance and for induction furnaces are presented. In addition to this, metallurgical results are given from experiments where this furnace control was applied."

Jan 1, 1989

By J. S. Vanderploeg

I WILL begin this presentation by citing the annual per capita use of copper in Canada. This is best calculated by taking refinery domestic sales, plus imports of the products of foreign fabricating mills (very little refinery copper is imported), and deducting the exports of Canadian mills. No attempt has been made to estimate the copper content of imports or exports of machinery, motors, etc., but the trade balance here is probably against Canada. In any event, we find that, though varying somewhat since the war, the estimated yearly per capita figure has reached a high of 18 pounds. This is practically on a par with the United States. The rest of the world uses an average of about 2 pounds per capita, yearly, though this includes some countries, such as Sweden, Germany and England, which consume much better than average quantities. It looks, therefore, as if the Canadian copper industry has not (as has been generally charged) been asleep after all.

Jan 1, 1962

By D M. Frantois-Bongarton

"A few situations are first reviewed where practical shortcuts lead to acceptable solutions where none seemed to be possible. These include: The solving of many complex sampling optimisation problems with the simple approach of the worst case policy (WCP). A simple approach to single-stage sampling problems will be mentioned at continuation. In the plants, minimising the impact of border effects in incorrect samplers, so that the resulting samples are approximately correct and acceptable in practice because the bias risk attached to them is controlled. Examples are given, as well as practical tools and a general methodology.Finally, some sources of undue conservatism are reviewed with general recommendations aiming at eliminating them.CITATION:Frantois-Bongarton, D M, 2012. Practical considerations and shortcuts in sampling, in Proceedings Sampling 2012, pp 171-174 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 21, 2012

These proceedings consist of papers presented at three Bureau of Mines Technology Transfer Seminars on ergonomics in the mining industry. These seminars were held in December 1981, and covered topics relating to ergonomics and mining in the areas of the man-machine interface, and design of the work environment. This area of research is directed toward reducing accidents traditionally associated with human error.

Jan 1, 1981

By E. D. Gardner

This is one of a series of papers describing mining and related subjects affecting mining in western mining districts and mineralized areas. The parts of this paper pertaining to current production, mining and milling methods and practices, and general conditions affecting mining were collected principally during a field survey made in May 1935. Some original data obtained on previous visits to the area are also included. The history, geological background, and past production of the mines and district are largely abstracted from previous publications, for which due credit is given later in the test. The principal districts in the Black Mountains are the Oatman or San Francisco and the Union Pass or Katherine. This range contains the principal producing mines of the State, in which gold is the only important metal. Although the total production of gold is relatively small as compared to other districts where the precious metals are obtained as a by-product in copper min¬ing, the area is one of considerable economic importance to the State.

Jan 1, 1936