Search Documents

By E. K. Stanek

This research study was performed on a case study basis and can be divided into two parallel thrusts: electrical and thermal energy conservation. Energy consumed annually in mining and refining operations represents about 6% of the 80 quadrillion Btu's consumed nationally. In the electrical portion of the study, five areas were addressed: optimal dispatching of on-site generation, high-efficiency motors, conductor selection, power factor correction, and high efficacy lighting. In the case study mine which has a multiple unit on-site generation system, optimally dispatching units can save significant energy. The other four methods are difficult to justify on a retrofit basis due to capital costs. In the thermal portion of the study, a thermodynamic analysis was performed on the reverberatory smelting process possible areas of energy conservation were identified as radiation and convection heat losses from the furnace arch and the dumping of high energy content smelting slag. It has been shown that materials currently available can provide the means of reducing heat loss from the reverberatory furnace. It has also been shown that a significant amount of energy may be recovered from the slag. However, these are both subject to further study and validation.

Jan 1, 1982

By Stephen H. Chung

The SABREX computer blast simulation program permits the study of the effective use of explosive energies and predicts the total performance of a blast in terms of:fragment size distribution: muckpile profile; breakage at grade, column and collar with respect to the control case; crack penetration; damage envelope behind and beneath blastholes; a complete cost analysis including explosives, drilling and accessory costs

Jan 1, 1995

By M. M. Tilman

In a Bureau of Mines investigation to develop lead alloys with improved tensile strength and creep resistance, lead-base alloys containing cadmium and antimony in nominal 1-to-1 atomic ratios were melted in air, cast, and rolled into sheet to 90 percent reduction at temperatures varying from room temperature to 175° C. Tensile testing at room temperature and stress-rupture testing at 900±3° F were conducted on the as-rolled alloys. The best tensile properties were observed in an alloy of Pb-4.2 wt pct Cd-4.5 wt pct Sb which exhibited an average tensile strength of 7,270 psi with 36 percent elongation in 2 inches. An alloy of Pb-5.5 wt pct Cd-6.0 wt pct Sb had 100-hour stress-rupture values of approximately 2,100 psi and 1,000-hour values of approximately 1,700 psi.

Jan 1, 1969

By M J. Begbie, K B. Sporle

The Golden Cross low sulfidation epithermal deposit produced approximately 750,000 ounces of Au from two ore zones: the underground Empire Vein System and the open pit stockwork. The Empire Vein System has at least eight stages of vein formation: (1) sulfide veins, (2) black veins, (3) massive veins, (4) banded veins, (5) thin white veins, (6) crumbly veins, (7) massive/platy calcite veins, and (8) flattened rhomb calcite veins. Gold mineralisation occurred relatively early in the lifetime of the system, dominantly during 2 through 4. The late calcite veins (7 and 8) and early sulfide veins (1) are barren. The vein system formed in a dominantly extensional environment, though some compressional faulting may have also existed during vein formation. There is no evidence for significant strike-slip faulting during vein formation, highlighting the fact that explorationists should pursue on-site structural patterns rather than fashionable models.

Jan 1, 1998

By Luis Martín Tejeda

El presente texto señala cómo los parámetros geotécnicos de resistencia y deformabilidad pueden generar mayor confiabilidad en un estudio técnico. En este sentido, la literatura geotécnica indica que los resultados obtenidos a través de métodos numéricos son sensibles a la variación de estos parámetros y que algunas propuestas de cálculo son más satisfactorias. Para ello, se utilizó el criterio de falla de Hoek & Brown en términos de Mohr–Coulomb, donde se presenta un ejemplo aplicativo para mineria superficial, en el cual el factor de seguridad y la probabilidad de ruptura del macizo rocoso son calculados mediante métodos geoestadísticos aplicados a la ingeniería de rocas (FOSM - First Order Second Method y puntos de estimación de Rosenblueth).

Sep 19, 2006

By D. C. Lynch

While a sizable amount of data exist as to the activity and distribution of minor elements between matte and metal, there has been no unifying theory presented delineating the form of dissolution of these elements in molten sulfides. In order to alleviate that deficiency the literature concerning the behavior of As, Sb, Bi and Pb in mattes is reviewed. Models present in the literature, regarding the thermochemical behavior of minor elements, are tested, and new models are presented and evaluated using thermodynamic theory. The results of those analyses are used to predict optimum conditions for the volatilization of minor elements. The dearth of data on the behavior of minor elements in nickel mattes requires that this review focus on copper- iron mattes. An effort is made, however, to utilize basic knowledge regarding nickel sulfides and the interaction of nickel with the minor elements to predict the behavior of those elements in nickel-copper and nickel-iron mattes.

Jan 1, 1993

By Omid Lashkari

Keywords: SEED, SSM materials, Microstructural evolution, Rheology, Swirling Speed SEED (Swirled Enthalpy Equilibration Device) is established itself as a new technology amongst the many Semi-Solid Metal (SSM) processes, where swirling of the mush plays an important role in modifying the dendritic structure of as-cast parts. A range of semi solid metal structures, dendritic, rosette and/or globular morphology of primary phase, can be prepared using SEED. The current article reports on the application of rheological tests in characterizing microstructural evolution during SSM processing of 356 Al-Si foundry alloy. A simple parallel plate test machine, designed and constructed at our labs, was used to determine viscosity values for each structure and identify the optimum structure with superior die filling characteristics. Such findings have important technological and economical implications during high pressure die casting of semi- solid metals. The strain-time graphs for 356 Al-Si foundry alloy indicated lower viscosity values for globular microstructure, i.e. improved die filling.

Jan 1, 2005

By F. F. Peng

The raw-coal feeding system and the upward medium current flow in a dense-medium vessel (DMV) are, in addition to the residence time of particles in the separator, important factors for efficient coarse particle separation. The feed material from a raw coal screen and/or pre-wet screen merge with the major volume of circulating medium as push medium, guided by an adjustable submergence baffle plate deep fed into the separator for effective separation. The remaining volume of the circulating medium enters from the purge and drain hoppers at the bottom of the DMV. This generates a gentle upward medium current flow in the separator, which prevents dense medium stratification/settling and merges as part of the push medium. A two-dimensional, two-phase model developed using computational fluid dynamics (CFD) is used to describe the flow pattern and evaluate the function of the dip plate for understanding the mechanisms of particle separation in the separator. The particle movement in the DMV is also tracked to investigate the major operating parameters affecting the separation performance of the DMV. The simulation results of the DMV separation performance are validated by in-plant test data.

Jan 1, 2007

By M. Nete

Qualitative analysis of three mineral samples from northern Mozambique was accomplished by X-ray diffraction (XRD), microscopy, scintillation, and magnetic determination. Chemical characterization was accomplished using ICP-OES and pressed powder XRF after dissolution using microwave-assisted digestion and flux fusion. The samples consisted of a mixture of minerals with tantalite as the major component, with minor amounts of microlite, quartz, mica, accessory garnet, and tourmaline. Incomplete dissolution was obtained using microwave digestion, with maximum recoveries of 90.25 ± 0.06% and 88.90 ± 0.04% for Nb2O5 and Ta2O5 respectively. Complete dissolution using Li2B4O7 resulted in recoveries of 98.5 ±0.2% Nb2O5 and 100.4 ± 0.3% Ta2O5.

Jan 1, 2012

By X Qiu

According to the temporal and spatial distribution of regional metallogenesis, thePacific Rim can be divided into four global metallogenetic systems. The Asia-Australia W-Sn metallogenetic belt is the typical representative of intracontinental metallogenetic systems. This belt resulted from Mesozoic and partly pre-Mesozoic tectonic magmatism, mainly related to S-type granite of crustal source that was generated by collisional orogeny combined with oceanic subduction in intracontinental and continental margin settings. Based on the concept of metallogenetic series, there is a group of mineralised ore types showing a definite spatial and temporal distribution from endogenetic to exogenetic. These metallogenetic series are widely distributed in the Asia-Australia W-Sn metallogenetic belt, and are well developed in Southeast China. Five metallogenetic series and two petro-minerogenesis evolution models have been established according to their tectonic settings, various types of granitoids and metallogenetic evolution.

Jan 1, 1995

By Helmut Hass, Michael B. Gilbert

The extension of the commuter railway system (S-Bahn) in Leipzig, Germany willrequire the construction of an underground line crossing the downtown area of thecity to tie the Bavarian Station in the South to the Main-Station in the North. The City-Tunnel-Leipzig is currently one of the largest infrastructure projects in Europe. This system extension will have a length of approximately five kilometers. 3.9 kilometers of that length are currently being constructed using either cut & cover construction or tunnelingmethods. The design and construction of this project currently is and will continue facing very significant challenging urban and demanding geotechnical conditions.

Jan 1, 2007

By Douglas Milne

Most empirical and numerical approaches to design in rock mechanics incorporate rock mass classification. Numerical design methods generally use classification values to calculate input parameters for stress-based failure criteria. Empirical methods use classification to allow comparisons between similar rock mass conditions, generally based on a graphical design technique that differentiates stable and failed opening geometries. Classification systems are the best tool available for assessing rock mass properties; however, there are problems with classification systems that should be high-lighted. Rock mass performance can only be realistically estimated by coupling a unique description of the rock mass with known loading conditions. Current classification systems cannot provide a unique classification value. The weightings applied to quantify rock mass properties for classification can result in significantly different rock masses having the same classification values. These weightings have been proven effective for tunnel design and support, but classification systems are now used for many more applications. Rock classification systems evolved from a quick and easy field tool for estimating tunnel stability and support requirements. The need for a rapid field tool means that rock mass classification is relatively insensitive to improved methods of measuring rock mass properties. Problems with classification systems and their application are highlighted in this paper. These problems must be recognized and documented before improvements can be made. An understanding of the evolution of classification systems and their application for both numerical and empirical design approaches is invaluable in highlighting current shortcomings.

Jan 5, 2007

By A. Muwila

Hercules? is a low nickel austenitic stainless steel developed at Mintek that has a typical composition of 9 wt% Mn, 0.05 wt% C, 2wt% Ni, 0.25 wt% N and 16.5 wt% Cr. A more corrosion resistant version of Hercules? (Hercules? B) with 0.5 wt% Mo has also been developed. Potentiodynamic tests performed on Hercules? B in a 5wt% sulphuric acid solution showed it to have improved corrosion resistance comparable to that of AISI 304. The effect of a varying Mn content on the corrosion resistance of Hercules? B has also been investigated and the results discussed in this paper. From the corrosion test results, it is clear that decreasing the Mn content of Hercules? B increased the corrosion rate, while increasing it decreased the corrosion rate. Keywords: austenitic stainless steel, % ferrite, molybdenum, manganese, nitrogen, electrochemical corrosion tests, potentio-dynamic scans, microstructure, chemical analysis.

Jan 1, 2007

By Arnis Mangolds

A study of the technical and economic feasibility of using a unique undercut and fill system developed by USBM engineers to mine steeply pitching coal is discussed. A brief resource assessment has indicated that significant reserves exist in most coal regions to justify the development of a safe and economical method of extracting steeply pitching coal. The undercut and fill system combines hydraulic coal cutting with unassisted gravity fluming of the coal slurry. Mining occurs across strike and the extended entry is backfilled to provide uniform strata control and an impermeable water and air barrier. Subsequent mining occurs beneath the previously filled stope such that the roof consists of a solid, controlled back. In addition to providing positive roof and hanging-wall support, the backfill system eliminates subsidence potential, post-mining drainage, and the danger of spontaneous combustion from naturally drafting air currents. A unique through-flowing ventilation system permits passage of return air through the production face via ducting located at the backfill-coal junction. This provides a constant supply of fresh air at the face, eliminates the need for brattice cloths, and provides an additional escapeway for the miners. The preliminary estimates indicate a production rate in the neighborhood of 31.9 tons/ manshift. Capital costs are approximately $3.17/raw ton over a 20-year life with an initial investment per annual ton of $48.29. Total cash-costs for labor, supplies, power and benefits range in the vicinity of $19.59 for a 704,460 ton/year mine, or a total cost of $22.76/ton. These costs do not include federal and local taxes or post-of-money; however, the cost of coal is well within the area selling price.

Jan 1, 1981

The NIOSH suite of coal mine ground control software addresses nearly every aspect of coal mine ground control planning, including geologic characterization, mine layout, pillar design, and support selection. Mine planners who use the soft-ware have access to the knowledge gained during years of NIOSH research—packaged in a simple, easy-to-use format. Several of these software packages have recently been updated and improved. Analysis of Roof Bolt Systems (ARBS) (Figure 1) helps select the proper roof bolt system design from the immense variety of available bolt types and patterns. It was developed from statistical analysis of extensive bolt performance and roof fall data. New features in Version 2 include— • The capability to analyze roof bolt systems that use two types of bolts; and • A roof support cost module that estimates the total in-stalled cost of different patterns, considering the costs of consumables, labor, maintenance, and other factors. The Support Technology Optimization Program (STOP) (Figure 2) can be used to make judgments regarding which secondary support system will be the most effective in a particular mine condition and to evaluate the advantages or dis-advantages of alternative support systems. Version 3.0 includes additional improvements: • Supports with large load-shedding following yielding can be designed based on the peak loading capability as well as the residual loading capability; • Seven new support systems have been added to the program; and • Easier access to photo gallery has been provided. The Coal Mine Roof Rating (CMRR) replaces com-plicated geologic information with a simple numerical rating that mine planners can use in many ground control applications. The CMRR can be readily integrated into a geologic exploration program, and the software package is capable of generating an AutoCAD CMRR "layer." Version 1.2 contains— • The complete CMRR database with more than 250 ratings obtained from 70 different U.S. coal seams; and • An all-new "Help" file that clearly explains all aspects of the program. Analysis of Horizontal Stress in Mining (AHSM) can help find the optimum mine layouts for control of horizontal stress. It can be used to analyze both development and longwall retreat designs, and it shows how the stress condition varies as the entry, crosscut, and panel orientations are changed. Version 2 features— • Improved graphics that enable the user to observe the effect of design changes without adjusting the display on the computer screen; and • Resource files containing information on stress map-ping, advance-and-relieve mining, stress measurements in U.S. coal mines, and other topics. [ ]

Jan 4, 2006

By Jim Excell, Jim Rothwell, Mike Rylati

"LocationThe Ekati Diamond mine is located at Lac de Gras, Northwest Territories.Brief Description of OperationBHP Diamonds Inc. has developed Canada's first diamond mine in the Northwest Territories (NWT), Canada. BHP Diamonds Inc. is part of the BHP World Minerals Division ofBHP Minerals. The project is a joint venture between manager and operator BHP (51%) and the Blackwater Group (49%). The Blackwater Group comprises Dia Met Minerals Limited, Charles Fipke and Stewart Blusson.Production at the NWT diamonds project began in October with the mine officially opened October 14, 1998. The project is situated on an 853 000 acre claim block located in the Lac de Gras region of the NWT. It is about 300 km northeast of Yellowknife and 100 km south of the Arctic Circle. The seasonal winter ice road to the Echo Bay Lupin mine passes along the eastern margin of the project area. This allows road access each year from mid-January to mid-April. For the remainder of the year, the project is accessible only by air.HistoryIn 1980, Charles Fipke traced indicator minerals east from the Mackenzie River area. He discovered indicator minerals in the Lac de Gras area and staked mineral claims in 1989. A joint venture was formed between BHP and Dia Met in 1990, and in 1991, the first diamonds in the NWT were discovered at Point Lake by BHP and Dia Met. This initiated the largest staking rush in Canadian history. The joint venture launched an aggressive exploration program.Koala, Fox, and Leslie were identified in 1992 as potentially economic pipes.As soon as the project's potential was established, it was recognized that an enormous amount of work had to be completed in several areas before a mine could be developed, namely: technical evaluation of the resources; environmental and socio-economic evaluation to procure the necessary permits for the development; and engineering design to optimize mining and processing of the resource and to comply with specific environmental requirements."

Jan 1, 2000

By S. A. Falconer

The benefication of non-sulfide or non-metallic minerals by froth flotation has been practiced commercially for at least 30 years. In the pioneer stages of development of this flotation art, most of the promoters investigated were fatty acids or soaps that had been found to float sulfide minerals. When commercial application of froth flotation started to assume importance in the late 1920' s and 1930's, a great deal of fundamental research work was done in the laboratory (11-14, 19, 22, 23, 26, 29, 32). Among other subjects, this work included studies of the relative effectiveness of the different fatty acids and their salts on the flotability of various non-sulfide and non-metallic minerals. The successful present-day use of fatty acid and petroleum sulfonate type promoters results from better understanding of the principles of non-sulfide flotation plus the developnent of effective selectivity modifying agents. Many investigators have contributed to a greater appreciation of the numerous interrelated factors involved in fatty acid and soap flotation of non-sulfide minerals. Of these, mention should be made of recent fundamental studies by Tagart and Arbiter (31); Wolstenholme and Schulman (35); Schulman and Smith (28); Wark and his co-workers(3,4) Du FIietz(l5); and J. Leja(24). According to J. Rogers, K. L. Sutherland and E. E. and I. W. Wark(27), "the basic requirements for a 'collector' in flotation are that it shall form a film over the surface of the mineral to be floated and that this film should be oriented so that hydrocarbon (non-polar) groups form the effective surface." When modified in that way, the mineral surface possesses some degree of air avidity. All investigators would agree with Taggart, Taylor and Ince (33)that such a film can be produced only if the collector compound contains an active (polar) group to be attracted to the mineral surface, as well as the non-polar group. The commonly used anionic-type promoters for non-sulfide, non-metallic and metallic oxide ores include: 1. Fatty acids, and their soaps and emulsions. 2. Fatty acids residues — "pitches" and "foots." 3. Sulfonated and sulfated fatty acids and so-called "petroleum sulfonates." 4. Paraffin chain salts — sulfonated and sulfated higher alcohols. 5. Cyclic organic acids or salts, such as naph-thenic acid and naphthenates. Certain fatty acids are more effective than others as promoters for particular minerals under certain specified conditions. Some of the more costly fatty acids or collectors of the paraffin chain salt type may give improved selectivity in some instances and are being used commercially in a limited number of operations. Local availability may dictate the choice of the fatty acid used — for example, the use of palmoil fatty acid for flotation of copper carbonate ores in the Belgian Congo. Coconut oil fatty acids have also found limited use.

Jan 1, 1961

By James C. Patterson

Sintered fly ash was shown to have promise as a modifier for poorly drained soils. Turf grown in mixtures of sintered fly ash and soil benefited from increased water-infiltration rates, greater total pore space, and higher moisture availability, The result was an improved turf stand with increased grass yield and root density.

Jan 1, 1970

By F. D. DeVaney

The low-grade deposits of manganese ores along the Missouri River near Chamberlain, S. Dak., are known to contain one of the largest reserves of manganese in the United States. Manganese occurs as concretionary nodules ranging in size from 13 inches in their longest dimension to particles finer than 65-mesh. The nodules are embedded in soft, wet shale, which contains little manganese. The removal of nodules from the low-grade shale is a simple mechanical -problem; the question is primarily to determine the lowest-cost method of separation. This report purposes to present data acquired by experimenting with samples of the ore, which form a basis for suggesting methods of concentrating manganese nodules.

Jan 1, 1942

By F. D. DeVaney

The low-grade deposits of manganese ores along the Missouri River near Chamberlain, S. Dak., are known to contain one of the largest reserves of manganese in the United States. Manganese occurs as concretionary nodules ranging in size from 13 inches in their longest dimension to particles finer than 65-mesh. The nodules are embedded in soft, wet shale, which contains little manganese. The removal of nodules from the low-grade shale is a simple mechanical problem; the question is primarily to determine the lowest-cost method of separation. This report purposes to present data acquired by experimenting with samples of the ore, which form a basis for suggesting methods of concentrating manganese nodules.

Jan 1, 1942