Search Documents

At the exploration stage for new mining projects or for medium- and long-term areas of existing mines (typical of South African gold mines), drilling data is on a relatively large grid. This grid is normally larger than the selective mining units (SMUs). Direct estimates for the SMUs and also of much larger block units will then be smoothed due to the information effect and the high error variance. Any capital-intensive project decisions made on the basis of any of the smoothed estimates will tend to misrepresent the economic value of the project or operation, i.e. the average grade of blocks above cut-off will be underestimated and the tonnage overestimated for cut-off grades below the mean grade of the orebody. This paper presents a direct approach technique for deriving recoverable resources, referred to as localized direct conditioning (LDC), designed to correct smoothing effects and also to provide support corrections.

Jan 1, 2014

By H Phillips, A Spaeth, B Belle

There are several well-known, extensively researched and tested methods of suppressing a coalmine methane and coal dust explosion. The choice of method used is dependent on the legislative requirements of each country, which in turn are influenced by mining conditions in that jurisdiction. For example, seam gas content and the dustiness of the coal will combine to create the hazard, while the physical and chemical properties of the seam might influence the possibility of ignition sources such as frictional ignitions. The mining method and layout will also influence the choice of preventative or proactive suppression devices. The decision as to which method is approved and adopted should be based on currently tested and available technology and the latest research outcomes, and should be subjected to a rigorous risk assessment, since a methane explosion propagating into a coal dust explosion cannot be countenanced.Every new technology must undergo stringent tests and these tests must be certified by accredited research facilities or laboratories. Upon approval, an explosion suppression system or the critical components of such a system should be tested in a more realistic environment. This environment can ideally be found in an operating underground mining section for evaluation purposes. Based on the insight gathered in such an environment, a realistic evaluation of the effectiveness of a potential system can be carried out. The explosion suppression system described in this paper has been tested on numerous occasions at accredited test facilities. The technology described in this paper has been used in various applications in underground coalmines and has been adapted to fulfil and exceed the requirements set out for methods currently in use. This paper describes the underground evaluation results of the latest technology in active suppression systems as used on continuous miners was adopted to perform as a roadway explosion barrier.CITATION:Spaeth, A, Belle, B and Phillips, H, 2017. Underground bulk sampling, uniform conditioning and conditional simulation – unrealistic expectations?, in Proceedings Australian Mine Vent Conference 2017, pp 197–202 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 28, 2017

These proceedings consist of papers presented at a Bureau of Mines Technology Transfer Seminar in September 1981 for the purpose of disseminating recent advances in mining technology in the area of premining research. The introduction and descriptive papers discuss techniques and instrumentation used in premining research for metal and nonmetal mining and shaft design and borehole control for premine planning.

Jan 1, 1982

By Christopher J. Bise

INTRODUCTION A mine's power system represents the driving force behind all of the extraction and auxiliary operations, because the production and transportation of mined material and the operation of equipment, such as fans and pumps, are all dependent upon a power source. Once, compressed air was the primary power source in mining; today, however, electrical power dominates. This chapter reviews the basic theories of com- pressed-air and electrical power and provides several examples of applications in mine power systems. COMPRESSED-AIR POWER General Compressed air has been, and should continue to be, an important source of power in mining operations. It has been used as a means of blasting coal in conventional mining and is widely used to operate stopers, mucking machines, and other air tools in both coal and hard-rock mines. Such applications demonstrate the suitability of compressed air for applications requiring linear motion, but it is also utilized for its reliability and safety. A compressed-air system is composed of a compressor, a receiver, a distribution network, and the air-operated machines. A compressor takes in air at normal atmospheric pressure (free air) and compresses it to a higher discharge pressure. The discharge pressure must be high enough to overcome the friction in the distribution system of pipes and hoses and deliver the compressed air to the machines at the pressure recommended by the manufacturer. The most common type of compressor used in mines is the reciprocating compressor in which the air is compressed by a piston in a cylinder. An air receiver is a container or storage tank that is located in the distribution system between the compressor and the machines. It stores compressed air, when the full capacity of the compressor is not being used, and gives a more steady flow of air to the machines. The distribution network consists of pipes, Oalves, elbows, tees, and hoses that transmit the compressed air from the receiver to the machines in the mine. It is essential that the distribution system be designed with the proper sizes and lengths of pipe, hose, and other components to keep pressure losses well within allowable limits. The air-operated machines consist primarily of drifters, stopers, pluggers (sinkers), slushers, and several other pieces of equipment. Compressor Operation Every compressor is made up of one or more basic elements; a single element, or a group of elements in parallel, comprises a single-stage compressor. Many compression problems involve conditions beyond the practical capability of a single compression stage. Too great a compression ratio (absolute discharge pressure divided by absolute intake pressure) may cause excessive discharge temperatures or other design problems. It, therefore, may become necessary to combine elements or groups of elements in series to form a multi- stage unit, in which there will be two or more steps of compression. The number of stages commonly used in reciprocating compressors is as follows: Pressure Number of stages 0- 150 pig 1 80- 500 psig 2 500-2500 psig 3 2500-5000 psig 4 When pressure is referred to as pounds per square inch gage (psig), it means the pressure (in pounds per square inch) above barometric pressure as measured by a gage. The sum of barometric pressure and gage pressure is the absolute pressure (in pounds per square inch). The gas is frequently cooled between stages to reduce the temperature and volume entering the subsequent stages, thereby reducing the work required for compression. The basic reciprocating compression element is a single cylinder compressing on only one side of the piston (single-acting). A unit compressing on both sides of the piston (double-acting) consists of two basic single-acting elements operating in parallel in one casing. The reciprocating compressor uses automatic spring-loaded valves that open only when the proper differential pressure exists across the valves. Intake valves open when the pressure in the cylinder is slightly below the intake pressure. Discharge valves open when the pressure in the cylinder is slightly above the discharge pressure. In Fig. 1, Diagram A shows the basic element with the cylinder filled with air at atmospheric pressure. On the corresponding theoretical pressure-volume

Jan 1, 1986

By Zhiyun Li

Room temperature infrared reflection spectra of 2 n-type homo-epitaxial epifilms have been measured in the work. The effect of the refractive index on the determination of layer thickness using traditional calculation measurement is studied and some improvements have been added to the measurement to improve the accuracy and stability of the measured results. Results of the improved method have great agreement with the results from SEM and both variance and mean relative error decrease an order of magnitude.

Jan 1, 2010

By H. J. Sutherland

This paper reviews the results of the subsidence research prop ram at Sandia National Laboratories. The manuscript highlights the following: the application of empirical methods (profile functions) to the subsidence above longwall panels in the U.S.; the use of the "rubble model" to describe the behavior of broken strata as it distends when it falls to the Mine floor (or top of the rubble pile) and then is subsequently compacted as it is loaded by overlying elements of strata; and, the application of physical modeling techniques (centrifuge simulations) and numerical techniques to study the failure mechanisms in highly structured stratigraphy. The capabilities of the latter two are illustrated ')y comparing their predictions to the results of a field case that has complicated stratigraphy.

Jan 1, 1982

Paper 1: Risk of gastrointestinal cancers from inhalation and ingestion of asbestos, John F. Gamble Selikoff suggested the hypothesis that asbestos exposure is causally associated with increased risk of gastrointestinal (GI) cancers in an early study of insulation workers. In this paper, John Gamble reports on his extensive review and reanalysis studies that address the relationship between asbestos exposure and GI cancers. The purpose of the review was to evaluate the association between asbestos exposure and risks of stomach, colorectal, colon, and rectal cancers separately. Gamble evaluated exposure?response (E?R) relationships using surrogate exposure methods ??because few individual studies of GI cancer have reported exposure? response analyses.?? The principal asbestos exposure surrogates are: (1) the rate ratio (RR) for lung cancer; and (2) the percent of mesothelioma among exposed workers. Analyzing SMRs for GI cancers from individual studies versus the risk of lung cancer and mesothelioma provides crude estimates of E?Rs for asbestos exposure and GI cancer. Briefly, Gamble justifies the surrogate approach as follows:

Jan 1, 2007

By B. G. Tarasov

This paper proposes the further development of a recently identified shear rupture mechanism (fan mechanism) that elucidates a paradoxical feature of hard rocks ? the possibility of shear rupture propagation through a highly confined intact rock mass at shear stresses that can be significantly less than frictional strength. In the fan mechanism, failure is associated with consecutive creation of small slabs (known as ?domino blocks?) from the intact rock in the rupture tip, driven by a fan-shaped domino structure representing the rupture head. The fan head combines such unique features as extremely low shear resistance, self-sustaining stress intensification, and self-unbalancing conditions. Consequently, the failure process caused by the mechanism is inevitably spontaneous and violent. Physical and mathematical models explain unique and paradoxical features of the mechanism, which can be generated in primary ruptures and segmented faults. The fan mechanism provides a novel point of view for understanding the nature of spontaneous failure processes, including shear rupture rockbursts. The process explains, in particular, features of shear rupture rockbursts such as activation at great depths, generation of new shear ruptures in intact rock mass, nucleation of hypocentres at significant distances from the excavation, shear rupture development at low shear stresses, and abnormal rupture violence.

Jan 1, 2014

By M. P. Amsden

"Ecstall Mining Limited, a subsidiary of Texas Gulf Incorporated operates the Kidd Creek Mine, a 10,000 tons per day base metal producer, near Timmins, Ontario. Two different ore types are mined and milled: copper-zinc and silver-lead-zinc. At the highly automated Ecstall Concentrator the ores are processed by selective flotation in threes individual circuits. One of the most important metallurgical tools for process control is a sample system incorporating continuous on-stream x-ray analysis. Recently this system was further automated by adding computer control of reagents for two copper-zinc flotation circuits. The computer programs, utilizing optimum seeking methods and smelter contract terms, have increased copper recovery 0.8%, zinc recovery 1.6%, and reduced reagent costs by 12%. Although not anticipated, copper and zinc concentrate grades were improved modestly as well.INTRODUCTIONSEcstall Mining Limited, a wholly owned subsidiary of the Texas Gulf Incorporated operates the Kidd Creek Mine, one of the world's major base metal producers, near the old gold mining centre of Timmins, Ontario. Discovered in 1964, the property was brought into production in November, 1966. Originally designed for 9,000 tons per day, the operation now treats 10,000 tons per day of two different ore types mined from a single open pit. In the near future, open pit ore will be supplemented by ore from an underground operation now being readied for productionAt the Ecstall Concentrator the ores are processed by selective flotation in three individual circuits. The whole plant is highly automated and control is coordinated from a central control room. The treatment process follows conventional practices although fine grinding is required for optimum flotation recoveries. Normally, two circuits treat copper-zinc ore at a combined rate of 6,500 tons per day while the third circuit treats 3,500 tons per day of silver-lead-zinc ore. Special production averages 2,400 tons per day."

Jan 1, 1973

By Zhuo Chen, Jun Zhou, Jiemin Zhou

Samples of the reacting suspension particles were taken from the reaction shaft of a commercial flash furnace at different heights. The processes of matte and slag formation and morphology of the samples in the shaft were observed and analyzed. Variations of matte and slag composition in the shaft were investigated. By analyzing the samples taken from the settler at different locations, settler processes were studied such as slag formation, agglomeration and separation of matte-slag phases, Fe3O4 reduction, copper-in-slag reduction etc. In accordance with the characteristic of matte and slag formation the flash furnace can be divided into 6 functional regions, and a mechanism model called as “Micro bath process” is proposed for matte and slag formation in a commercial flash furnace. INTRODUCTION During flash smelting, concentrate particles scattered in the reaction shaft complete their oxidation reactions in suspension. The droplets produced fall into the settler beneath with a small amount of un-melted solid particles, agglomerate and separate into matte and slag layers which are tapped out from their tap holes separately. With respect to the extent of slagging reaction in the reaction shaft, there isn’t any commonly accepted understanding in literature (Kimura, Ojima, Mori & Ishii, 1986; Kemori & Kondo et al.,1988; Kemori, Denholm & Kurokawa, 1989; Fagerlund &Jalkanen, 2000). Some assume that the slagging reaction in the shaft can be ignored and some propose that all slag is produced in the shaft. With regards to the characteristics of the physical-chemical changes of concentrate particle in the reaction shaft, although there are some research results reported from pilot scale and commercial scale experiments (Kemori, Ojima & Kondo, 1988; Hagni, Vierrether & Sohn, 1988; Jorgensen, Taylor, Dickinson & Stevenson, 1992; Swinbourne, Simak & Yazawa, 2002; Kivinen & Tuominen, 2005), they are generally limited themselves to theoretical analysis and calculations. No studies are published concerned with the processes of matte and slag generation in the shaft, quantitative analysis of the processes, variations of matte and slag composition and morphologies of the melts along the axis of the shaft, etc.

Jan 1, 2019

By Jean-Marc Simard, Vincent Jourdain, Denis W. Roy

"Seven lithologic units, informally characterized, were recognized in the vicinity of the Montauban orebody. The first five lie in stratigraphic order. From structural bottom to structural top these are: (1) grey composite gneiss; (2) dark grey quartz-biotite gneiss; (3) quartz-biotite-garnet gneiss hosting several calcareous, aluminous and magnesian members and gold mineralization; (4) light grey quartz-muscovite-(sericite)-biotite gneiss; and (5) metabasafts. The last two intrude the sequence: (6) amphibolite dykes and (7) pegmatite veins. The orebody lies on the inverted limb of an overturned synform verging to the west with the metabasafts marking the core of the fold. As the foliation is folded, this fold is attributed to deformation ""D2""; deformation ""DI"" being responsible for the formation of the foliation. A late brittle deformation developed shear zones with probable strike-slip motions. The refined stratigraphy and the identification of the structural position of the orebody provide new tools for regional interpretation and prospecting.RESUMESept unités lithologiques ont été définies informeffement à proximité du gisement de Montauban. Les cinq premieres reposent en ordre stratigraphique; ce sont de la base au sommet structural: (1) le ""gneiss mixte gris""; (2) le gneiss gris forcé à quartz biotite; (3) le gneiss a quartz-biotite-grenat comprenant plusieurs membres calcareux, alumineux et magnésiens ainsi que la minéralisation aurifère; (4) le gneiss gris clair à quartz muscovite- Isericitel-biotite; et (5) les métabasaltes. Les deux autres unites sont intrusives dans la sequence: (6) les dykes d ‘amphibolite et (7) les veines de pegmatite. Le gisement se sitlie sur le flanc inverse d'un synforme déverse vers I' ouest dont les métabasaltes occuperaient le cœur. Comm e la foliation est plissée, ce pli est considère appartenir d la deformation ""D2""; la deformat ion ""DI"" etant responsable de la formation de lafoliation. Une deformation cassante tardive se traduit par des zones de cisaillement, d rejet apparemment directionnel. Cette stratigraphie plus précisé et l'indentification de la position structurale du gisement fournissent de nouveaux omits de prospection et d'interprétation regionalé."

Jan 1, 1987

By G. R. Fitterer

In the manufacture of steel by any process the refining period involves the partial elimination of the metalloids carbon, manganese, phosphorus, and silicon, by virtue of their reactions with ferrous oxide. At the end of this refining stage the metal consists chiefly of iron in which small amounts of these materials are dissolved. Unless some deoxidizer is added to the steel at this time, the reaction between carbon and ferrous oxide will continue with such force that it is impossible to form sound steal in the ingot molds. Instead, the product will exhibit a marked porosity due to the formation and trapping of carbon monoxide-the product of the reaction mentioned. However, if deoxidizers are added, steel may be obtained which is dense and free from gas bubbles. At the same time the deoxidation products will remain in the steal as impurities. For example, silicon additions form Si02 or combinations of Si02 and FeO. Additions of manganese form deoxidation products consisting of various proportions of MnO and FeO. It is also quite obvious that simultaneous additions of manganese and silicon will form oxide combinations either in the binary system MnO-SiO2 or in the ternary system FeO-MnO-SiO2. Work at the Pittsburgh Experiment Station of the United States Bureau of Mines, in cooperation with the Carnegie Institute of Technology and the Metallurgical Advisory Board, involved the study of such deoxidizing reactions and their products. In this connection considerable information is necessary concerning FeO, MeO, Si02, and Al 203, and their various combinations. Some of the most needed data are the melting points of all of these materials. At the outset of this work ordinary methods of melting point determinations were found to be inadequate for various reasons, and the procedure finally selected involved the use of the micropyrometer with occasional corroboration by quenching methods, The reasons for this selection, together with a description of the apparatus, are given in the following pages.

Jan 1, 1932

By R. O. Suominen, P. A. Taskinen, K. R. Lilius, A. T. Jokilaakso

Chalcopyrite concentrate was flash-oxidised in a laminar-flow furnace in oxygen-nitrogen atmospheres that ranged in composition from N2 to N2 + 50 vol% O2. Gas pre-heating temperatures were 500-1100 degrees C and four particle-size fractions were studied: 28-38, 38-44, 44-62 and 62-74 micrometres. The effect of the residence time of the particles on sulphur removal was studied in the range 0.1-0.35 s. Scanning-electron microscopy combined with energy-dispersive analysis and back-scattered electron analysis was used to determine the morphology and mineralogy of the reacted particles. Total desulphurisation was achieved under the most oxidising conditions. Particles were observed to undergo fragmentation during oxidation, the violence of this depending on the iron and sulphur contents and the original particle-size fraction. The melting and/or reaction stages of the particles under different conditions were studied in powder samples. Polished sections were examined to follow the development of porosity and the mineralogy of the particles. A model for the fragmentation process is described

Jul 1, 1991

By Alejandro Ferrada Vergara

Most blasting techniques that are designed to improve fragmentation and subsequently improve ore work index to downstream comminution processes, apply powder or energy factor increases, either by stretching the drilling pattern (burden/spacing ratio) implementing faster initiation sequences or using more energetic explosives. The new application will move detonation parameters up, making the blasting process riskier for the surrounding boreholes, explosive column or initiation systems functioning.

Jan 1, 2016

By H. Dong

This paper presents a heat conduction model to determine the erosion profile of freeze linings in a ferronickel submerged arc furnace. Kirchhoff transformation was adopted to simplify the nonlinear equation governing heat conduction. The boundary element method (BEM) and Nelder-Mead simplex optimization method were employed to solve an inverse heat conduction problem. Erosion profiles could be obtained when calculated temperatures at sensor locations agreed well with measured temperatures. The model was validated by comparing the heat loss through the linings, which was calculated by BEM and integral operation after erosion profiles were obtained, with the value calculated from industrial data such as actual power consumption, tap-to-tap time, and ferronickel output. The optimal solution for the erosion profile could be acquired when the difference in heat losses calculated by these two methods is at a minimum.

Jan 1, 2014

By D. F. Malan

This paper presents an overview of work conducted over several years to investigate the continuous stope closure profiles recorded in tabular excavations and the use of this data as a hazard indicator. In spite of the brittle nature of the rock, measurements in gold mines and intermediate depth platinum mines revealed a significant time-dependent closure component. Various approaches to simulate the time-dependent closure have been investigated. Viscoelastic theory is able to simulate the time-dependent closure behaviour, but there are subtle problems with the use of this theory as it cannot simulate the failure processes in the rock. To overcome these problems, continuum and discontinuum elasto-viscoplastic models were developed by the authors. Discontinuum models have the advantage of being able to simulate the creep behaviour of prominent discontinuities. Development of these models has led to useful insights into rock mass deformation and has made the numerical simulation of parameters, such as rate of mining, possible for the first time. A number of practical applications for the mining industry have been developed from this study. Among these are the delineation of geotechnical areas using closure data, use of the data as a hazard indicator and to give warning of large collapses in the platinum mines, identification of areas to be preconditioned in the gold mines, measurement of the effectiveness of preconditioning and improved da

Jan 1, 2007

This Bureau of Mines report reviews the information presented at the Sixth Mineral Waste Utilization Symposium cosponsored by the Bureau of Mines, U.S. Department of the Interior, and the IIT Research Institute. Environmental scientists and engineers from nine countries participated in the symposium, which was held May 2-3, 1978, at the Chicago campus of IIT Research Institute. The 56 papers presented on the reclamation and recycling of mining and mineral wastes, municipal solid waste, industrial wastes, and scrap metal are summarized herein.

Jan 1, 1980

By Chris Harnan

This paper describes the geology of three European cities and outlines how the geology has lead to the development of specific foundation construction techniques. Comparative tables of techniques commonly employed are given in Section 5. It can be seen that despite the presence of the 'single market', techniques still have wide diversity despite some similarities in geotechnical conditions.

Jan 1, 2000

By C. P. Kelley, T. J. McKeon

Several recent developments in fine screening technology have been implemented at the DuPont Starke, Florida plant allowing enhanced zircon recoveries while minimizing operator requirements and total operational costs. The total design concept came about through the efforts of engineers at Derrick Corporation (Buffalo, New York), DuPont Titanium Technologies (Starke, Florida) and Roche Mining (Carrara, Australia). The use of the Kelsey Jigs for zircon recoveries from the tailings stream requires two wet sizing functions in order to operate properly. The first wet sizing is required on the initial mineral slurry feed to the Kelsey Jig. This sizing is intended to protect the Kelsey Jigs internal screen basket from plugging with nearsize particles, thereby keeping production rates maximized. The second sizing function is intended to recover properly sized garnet ragging material, which inadvertently ends up in the tailings stream leaving the Kelsey Jig. The unique machine design developed by the three partners in this project incorporated both wet sizing functions (protection and garnet recovery) into a single patented high capacity wet screening machine fitted with patented screen surface technology. This screen surface technology allowed for high capacity slurry handling capabilities at separations as fine as 230 microns while experiencing no nearsize blinding and extremely long screen panel life. The high open area urethane screen surfaces utilized in the application typically last 20 to 30 times longer than stainless steel wire surfaces. The stacked machine design minimized total equipment requirements and screen footprint requirements, and reduced power consumption and overall installation costs.

Jan 1, 2005

By R. L. Castro

Block caving methods, when operated under favourable rock mass conditions, can achieve higher production rates and lower operating costs than other various existing underground mining applications. For this reason, it has been considered the preferred method for the mining of deep and large orebodies in current and future operations around the world. One of the key aspects in the design of block caves is the selection of the production level layout, which, among other parameters, is based on the gravity flow characteristics of the caved rock. This is because gravity flow has a large impact on total ore recovery and the amount of dilution in a caving operation. Today, there are a number of computer based methods which aim to emulate the gravity flow pattern of the caved rock. In this paper, the authors present the development of FlowSiman improved model of gravity flow based on the cellular automaton approach, to estimate dilution entry, mixing and ore recovery. As part of the model development, flow simulations were conducted and subsequently compared to full-scale data collected at two mine sectors operated by Codelco Chile. The results indicate that by using proper calibrated parameters, good correlations between simulated and measured grades as well as dilution entry are obtained. The potential use of the numerical tool to evaluate drawpoint spacing in terms of recovery and dilution for block/panel caving operations is also presented.

Jan 1, 2009