Search Documents

By Hans Perlid

In the handling of emulsion explosives pumping is a key operation. A number of serious accidents has shown that pumping can be a risky operation and should be carefully considered and investigated. This is the background behind a series of pump tests carried out by NITRO NOBEL.

Jan 1, 1996

By Sun Shao Xian

The Port of Shekou is situated at Shenzhen Bay on the east side of the Pearl River estuary. Geological condition of the site is quite complicated. On top of the sea bed, there is a layer of soft silt 8 - 14 m thick. Under the soft silt, there are intercalated layers of sand, silt and clay. Average surface elevation of the underlying undulatory weathered bed rock is about - 20 m, with a variation of about 10 m. In certain locations, the weathered bed rock is covered with a layer of silt 3 - 4 m thick. This paper gives brief account of three types of wharf structures which are of particular interest, constructed in the last few years: (A) Platform type wharf structure with frontal sheet piling and steel raking pile in the rear; (B) Relieving Platform type structure with steel sheet piling and inclined anchoring HP pile ; (C) Steel pipe pile row supported apron added to a marginal quay. Average construction time of a deepwater berth is about six months.

Jan 1, 1991

By Halvorsen N

For mining medium-hard materials on the surface, "Continuous Surface Miners" have been employed for some years. The latest generation surface miner extends the performance of this type of machine to the point where the same cost efficiencies can now be achieved in medium-hard materials as has been achieved in softer materials by machines such as the bucket wheel excavator. The paper explains briefly the technology of the Krupp Surface Miner (recently released to the market) and develops the costs of ownership and typical operating costs. Comparisons are made between a shoveLtruck system and Krupp Surface Miner (KSM) systems based on both truck and conveyor transport systems. Further benefits of mining with the KSM, such as environmental, selective mining and improved product reovery are discussed briefly. The equipment is now available to mine semi-hard materials (with compressive strengths up to 60MPa) on a continuous basis and reap the benefits which continuous systems can deliver. All new and existing open cut mines should review their costs with regard to this technology.

Jan 1, 1990

By Paulo José Costa Couceiro Junior, Manuel Lopez Cano

The biggest Port of Latin America - the Santos Port in São Paulo, Brazil - has been drilled and blasted by controlled underwater techniques in order to remove around 40,000 m3 (52,318 cubic yard) of rock divided in two outcrop rocks: Teffé and Itapema. Underwater pumped explosive, in combination with small cartridges areas, was successfully used in order to reach a target depth of -15m (-49 ft) and a width of 220m (722 ft) in the navigation channel. It was the first time that a pumped explosive was used in underwater blasting in Brazil and it represents a historic benchmark for projects of this kind in this country. The main challenges faced in this project include the control of the ground vibration, due to the necessity to carry out detonations 40m (131 ft) away from the quay wall - where the passenger terminal and the 80 year-old warehouse were located – and the rush schedule available, in order to finish the underwater drilling and blasting phase before the coming cruise season. Therefore, the perfect combination of an ideal pumped product with an effective pumping system has permitted to carry out the project in a record of less time than 3 months (against to the original expected time of 18 months), with all vibration events under control as result of the special ground vibration program carried out.

Jan 1, 2016

By J. Ritchey

This report describes the engineering feasibility and economic advantages of using a mobile bridge-type cross-pit belt conveyor system in conjunction with a large dragline to excavate and transport spoils in a typical Western surface coal mine. The studies show that such a system could be built to survive operational and climatic mining conditions, and that its implementation would offer a reduction in both acquisition and operating costs versus conventional mining units of comparable rapacity. Reclamation costs can also be significantly reduced, and the total reclamation process accelerated, making the cross-pit conveyor system attractive to mine Owners and environmentalists alike.

Jan 1, 1976

The mining industry has recognised for some time the importance of supporting programs which serve to educate the Australian public about the socio-economic benefits of mineral resource development. More recently, industry leaders have realised that the future development of the industry will depend on attracting sufficient young people to commit to a career in the industry. Apart from lending support to the traditional education institutions in Australia, the industry now has the opportunity to participate in the development of education programs in museums. Whilst historic, mining-related theme parks such as Sovereign Hill and Coal Creek in Victoria serve very effectively the objective of relating past mining activities to the socio-economic development of Australia, there still exists the need to provide a facility which, under the same roof, excites interest in geology, mining, mineral processing and the role of minerals and energy in modern society. The redeveloped Geological and Mining Museum (the "Mining Museum"), which is located in The Rocks area of Sydney, meets this objective. With the central themes of formation and transformation this new Museum, which aims to be the best of its type in the world, will use modern museum exhibit techniques and the resources of the Minerals and Energy Information Centre to educate the community including teachers and school children. In the best tradition of museums, outstanding mineral and other collections will complement a comprehensive range of interactive, high technology exhibits which will include a number of exploratory "hands on" facilities. Australian companies are joining with Government to fund this exciting new museum. There is still a need for industry professionals to realise that a modern "mining" museum is no longer just a repository for objects of mining heritage but is also an important centre which serves as an important educational and public relations interface. The Education Section of the new "Mining Museum", which is linked closely with the new Minerals and Energy Information Centre, will be working closely with appropriate mining-related Tertiary institutions to develop specific career programs aimed at secondary students who wish to pursue a career in the mineral resource industries.

Jan 1, 1989

By John Hoffert, Darren Colwell, Greg Tucker, Jeremy Kinch, Greg Rasmussen

"The Kemess Mine, a major producer of gold and copper, is located in north-central British Columbia. Kemess was brought into production in May 1998 by Royal Oak Mines. On February 11, 2000 Northgate Exploration Limited acquired Kemess Mine from receivership. Since acquisition in 2000 Kemess has seen many accomplishments, including the reduction of costs by 40%.One of the largest site capital costs was the construction of the tailings storage facility dam, which when finished will be one of the largest earth filled dam structures of its type. The existing construction design by AMEC called for a kilometer wide rock dam to be built from the 1350 M elevation to the 1504 M elevation at a 5.5:1 slope by hauling over 30 million tonnes of non-acid generating waste rock 7-kilometers from the open pit to the tailings dam, which was highly expensive.Kemess realized an opportunity for cost reduction was possible if the dam could be built from suitable quality tailings sand; however the sand did not meet the neutralizing potential ratio specifications. It was determined that cycloning combined with flotation to reduce pyrite concentration in the sand would produce a non-acid generating product for dam construction. The sand plant design challenges were to remove the sulphides from the tailings to obtain an NPR greater than 2:1 and provide a consistent sand product for the construction with a fines content of less than 15% passing 200 mesh. After a 2-year testing design and construction period, the sand plant was successfully started at the end 2002 resulting in higher than expected sand quality and production rates.This paper describes the plant design phase, commissioning, and operation of the tailings sand plant for construction of the tailing storage facility dam to enable us to meet all the engineering and regulatory requirements. The many challenges faced were successfully met using several innovative designs. The operational, economic, and environmental benefits are detailed."

Jan 1, 2004

By Terry M. Tilley, Gregory P. Sherry

Purpose This is a unique project because the mining and tunneling industries have become highly mechanized and cannot normally accommodate a project where surface disturbance must be minimized or eliminated when there is less than 10 feet of ground cover. More traditional less mechanized methods must be employed and the skills and techniques for accomplishing the work have become all but non-existent. Therefore, this article highlights those areas of specialized skills and techniques. Methods The article will describe the design approach, the method(s) of ground support selected, the method(s) of excavation selected, the planning, scheduling and materials selection process. In addition, the article will describe the actual production characteristics and the results of the project. This approach will concentrate on productivities, adaptations to actual conditions and the quality of the end product. The design approach basically was to insure that the temporary support methods were adequate for the excavation and shoring stage of the project. The final concrete liner was designed using conventional structural design methods with the goal of constructing a tunnel that will last 100 years. The methods of support were spiling and variations of spiling in order to provide advance temporary ground support. In this project spiling is steel channel cantilevered and driven into the ground ahead of the working tunnel face which supports the ground allowing the face muck to be removed with overhead protection’. Conclusion This will be a discussion of the applicability of the methods. The actual performance of the excavation and shoring methods will also be evaluated. The final concrete liner completion results, the actual production rates and the conformance with budget and schedule will be addressed.

Jan 1, 2005

By Ken Dyck, Chuck Edwards

"Cameco's McArthur River is the world's largest high grade uranium mine. Production started in late 1999. Cameco carried out the engineering design and construction management for the McArthur River project, including all aspects of mining, ore handling and ore transportation. The ore composition was expected to vary dramatically (0 to 30% U3O8; 0 to 25% clay; etc). To cope with the composition swings, sizing screens were selected to provide classification in the grinding circuit. The grinding circuit started up close to the design to provide minus 500 micron slurry. The 50% solids (wt) ground ore slurry proved to be difficult to transport to and process at the Key Lake Mill. Slurry containing high concentrations of high density pitchblende (about spgr 8.0) and low concentration of stabilizing clays, would settle in containers. Ore transport efficiency to Key Lake was found to be unacceptable.A test classification cyclone was installed in the grinding circuit at McArthur River early in 2002. The cyclone operating parameters were not typical, but the cyclone was made to work very successfully. Transportation efficiency to Key Lake increased due to more stable slurry. Preferentially ground (fine) pitchblende particles were easier to leach at Key Lake. The radiation exposure for operators and maintenance personnel to handle the more stable slurry was also reduced.The classification sizing screens were removed from the McArthur River grinding circuit and replaced by permanent classification cyclones late in 2002.INTRODUCTIONThe McArthur River mine and Key Lake mill operations are located in northern Saskatchewan, approximately 650 and 720 kilometres from Saskatoon, respectively. Figure 1 is a location map. McArthur River is the world's largest, high-grade uranium mine, with a production capacity of 18.7 million pounds U3O8 annually. (Rosner and Edwards 1998, Dyck 2000, Jamrozek 2000, Rodgers 2001) Proven and probable reserves are more than 473 million pounds U3O8. McArthur River ore, grading on average 21% U3O8, is milled at Cameco's Key Lake operation, 80 kilometres southwest by road. McArthur River production began in December 1999."

Jan 1, 2004

The selection of the best comminution circuit for the preparation of concentration feed is a compromise based on economics, energy efficiency, labour costs, steel consumption, availability and other factors specific to each case. It is postulated that the selection must be a choice of one of the eight basic comminution circuits which can be divided into two basic groups, (1) autogenous or semi-autogenous primary mills with or without a secondary grinding stage and (2) fine crushing usually in cone crushers followed by a rod mill-ball mill circuit or a single stage ball mill circuit. The accuracy of selection may be improved by pilot plant and laboratory tests which are described in this paper. For (1) above, testing includes media competency tests with standard impact crushing, grindability and abrasion tests followed by pilot plant tests. For (2) above, bench scale crushability, grindability and abrasion testing is available. It is suggested that, through these tests, it should be possible to eliminate all but one in each group of basic comminution circuits. Then engineering and economic studies should lead to the best comminution circuit for the specific requirement.

Jan 1, 1984

By Doug Harding

The Niagara Tunnel Project (NTP) is a 10.4-km- (6.5- mile-) long, 14.4-m (47.5-ft) bored tunnel that will run under the city of Niagara Falls from the Upper Niagara River to the Sir Adam Beck power station. The completed project will enhance the capacity of the Sir Adam Beck power station by adding 500 m3 /sec (17,657 cu ft/sec) of water through the tunnel. The project uses the world?s largest hard-rock tunnel boring machine (TBM) at 14.4 m (47.5 ft) in diameter to excavate the tunnel. Features of the project include the use of a high performance (HP) main beam TBM, state-of-the-art ground support and tunnel logistics systems. A continuous conveyor is used for muck transport from the TBM to the disposal area In June 2004, the Ontario government announced that Ontario Power Generation (OPG) had been given approval to proceed with the third tunnel under the city of Niagara Falls ? the first two tunnels were constructed in the 1950s using drill-and-blast techniques. The third tunnel, appropriately named the Niagara Tunnel Project (NTP), consists of a 10.4-km- (6.5-mile-) long TBM-bored, concrete-lined tunnel with a finished diameter of 12.5 m (41.1 ft). In August 2005, OPG the selected of Strabag of Austria, one of the largest construction companies in Europe, as the contractor to build the NTP at a price of C$600 million. In September 2005, Strabag selected The Robbins Co. of Solon, OH to design, manufacture and deliver a new 14.4- m- (47.5-ft-) diameter high performance, state-of-the-art main beam hard rock TBM to be used in the excavation of the tunnel. To meet the aggressive construction schedule as requested by OPG/Strabag, the TBM needed to be sup-plied as ready-to-bore within a 12-month period after the contract was awarded to Robbins.

Jan 1, 2008

By W. R. Dengler, R. S. Brown

In 1974, Brunswick Mining and Smelting Corporation Limited started a 48 million dollar expansion programme at their property in Bathurst, New Brunswick. A portion of the expansion plans includes a 26 foot diameter 4,525 foot deep shaft, underground crusher and conveyor excavations and lower level access development. J. S. Redpath Limited was awarded the contract for the new shaft and associated rock work in May 1974. Brunswick Mining and Smelting Corporation Limited, a member of the Noranda Group, operate this 10,000 ton per day lead, zinc, copper plant with proven reserves in excess of 90 million tons. While most of the ore is provided by the underground operation at the Number 12 ore body, some tonnage is produced from the open pit at the Number 6 ore body. Long range plans indicate a phasing out of the open pit and an increase in production from the underground operation. Existing facilities at the underground mine could not provide additional tonnage, thus the requirement for a new shaft. (Figure 1) The new shaft will also provide access to ore below the 2,800 level which is currently the bottom level of the existing facility. The contract called for sinking a 26 foot inside diameter, nine compartment concrete shaft 4,525 feet deep (Figure 2). Station access and ramp development from existing workings would be required to the bottom of the new shaft. In addition, development work for new crushing and conveying facilities was needed simultaneous with the shaft sinking.

Jan 1, 1976

By C. Allen

Vale Inco Ltd. is trialing several energy conservation initiatives in an effort to minimize costs and reduce green house gas emissions. The Ventilation on Demand (VOD) concept is a major project being carried out in various phases at Vale Inco mines. Due to the complex nature of a dynamic VOD system, Vale Inco is taking a systematic approach of testing VOD system components with milestone evaluations of each project. Coleman Mine was selected to pilot test the functionality and robustness of automated louvers in the underground environment; with the goal of optimizing mine airflow such that ventilation would be available for developing a new ore body. This project involved installing automated louvers in the exhaust raises; and installing variable frequency drive (VFD) starters on auxiliary supply fans. Because the VOD project created efficient utilization of the ventilation air in the 153 OB, the 170 OB is currently being developed without increasing the total fresh air into the mine. This paper describes the louver system component of VOD as applied at the mine.

Jan 1, 2009

By E. S. Chalpin

On 25 August 1971, the U.S. Bureau of Mines contracted with the Aerojet Liquid Rocket Company to perform an engineering research program to be completed on 25 May 1972. The program objective was to evaluate the advantages and disadvantages of the underground use of several power sources including but not limited to a closed cycle diesel, electric cable/motor, rechargeable battery/ motor and exhausting diesel for mine shuttle cars, with emphasis on health and safety. This report, Research in Advanced Power Systems for Mining Health and Safety consists of four (4) main parts: (1) Hazards and Safety Analysis of Mine Power Systems, (2) Evaluation of Closed Cycle Diesel Power System for Mine Applications, (3) Closed Cycle Diesel Power System Consumables Compatibility, and (4) Concluding Remarks and Recommendations. The hazards introduced to a mine by shuttle car power system failure modes were evaluated and reported. A "fault tree" analysis was generated for each power system and the probability of death or injury during an eight (8) hour shift and for a week of operation (105 hours) were estimated. Advantages and disadvantages were also reported for each system studied. Aerojet's assessment, based on a "forced decisions analysis," of the four shuttle car power systems as to their relative health and safety is that the exhausting or open cycle diesel is preferred, followed by the closed cycle diesel, the electric cable/motor and the rechargeable battery/motor. The assessment was based on ten parameters pertinent to the health and safety aspects of shuttle cars. Drawing layouts of two typical mine shuttle cars incorporating closed cycle diesel powerplant concepts are included in this report. The performance parameters established for the two concepts are tabulated. A study was made of the logistics involved in transporting and replenishing the consumables needed to operate a shuttle car equipped with a closed cycle diesel. The closed cycle diesel powerplant consumables -oxygen, potassium hydroxide, and diesel fuel - were analyzed as to their compatibility with materials found normally in a gassy coal mine. Spill tests simulating inadvertent leakage of liquid oxygen in a coal mine were performed. A critical evaluation of existing oxygen sensitivity data and the relationship to the use of oxygen on a shuttle car in a coal mine environment is presented.

Jan 1, 1972

Equipment-washing facilities at Freeport-McMo-Ran?s Sierrita Mine in Arizona produce a mixture of oil and water that was difficult to dispose of easily or cheaply. However, after some changes in the facility, waste oil is now used as part of the mining process. Freeport-McMoRan Copper & Gold Inc., head-quartered in Phoenix, AZ, operates copper, gold and molybdenum mines. It is the world?s largest producer of molybdenum. Heavy equipment used at the mine is hosed off periodically in the wash bay. The dirty water and oil mixture drains into the sump next to the bay. Oil was manually collected for disposal. This was a tedious and dirty process Mine managers sought a more efficient method of removing the oil. Instead of spending the time and effort skimming the tank with vacuums or sorbents, they enlisted the help of Abanaki Corp., manufacturer of the Model 4 Oil Grabber. Engineers designed the sump to utilize prevailing winds to blow the oil to one corner. This was the ideal place for the Abanaki skimmer. The skimmer removes the oil and discharges it into a plastic storage container. ?This reduces the time needed to keep the area clean, and the staff can focus on cleaning the equipment rather than worrying about the oil,? according to Jay Salerno, construction manager at the Sierrita Mine. Salerno is considering adding an optional oil concentrator to the skimmer to make the process even more efficient. The concentrator would remove any water picked up by the belt and return it to the sump, leaving nearly pure oil for disposal. Because the mine is located in the Sonoran desert, most of the water evaporates in the hot, dry air and is not reused.

Jan 1, 2009

The early records of hydraulic elevator and bucket ladder dredging in the Clutha River system indicate the success of that era of alluvial gold mining in Otago. This paper briefly reviews parameters of depth and gold grade for alluvial operations. The application of dragline technology is proposed for the economic removal of overburden to target the deeper alluvial gold areas which remain in the Otago region.

Jan 1, 1992

By V. Izaxon

Current practice in mining frozen, underground placers is to support the mine openings by leaving remnant pillars, which are kept frozen to maintain their stability. These pillars may be partially extracted depending on mining conditions, but this practice may be risky, and roof falls are common. Instead of allowing the mined-out areas to cave, the extracted entries could be filled with waste material, which would then be frozen, using cold ventilation air. A finite difference model for analyzing the effects of various parameters on the freezing of backfill in underground mines in the Arctic has been developed and tested. The model also accounts for properties unique to a frozen rock mass, including those that change with temperature. Examination of the characteristics of ice-cemented mining waste materials as backfill indicates that with proper engineering control, a backfill system can be designed for use in production mines. The system will allow increased extraction ratio while maintaining the stability of underground openings with minimum heat impact on the surroundings. These simulated results establish the relationships among the strength, the temperature, and the freezing characteristics of a given material. When coupled with site observations these relationships will facilitate the optimal design of ore pillar recovery methods.

Jan 1, 2004

By Arturo Ressi di Cervia

The utilization of diaphragm wall construction in Hong Kong began in 1974 with the construction of the New World Center, the first diaphragm wall job built in the British Colony. That landmark job of which I am presenting a few slides and a schematic description, embodied all of the difficulties and problems which are encountered in the difficult geology of Hong Kong. A small rocky island in the South China Sea, Hong Kong provides one of the finest natural harbors in the world. It is its splendid harbor, coupled with the enterprising attitude of the Hong Kong Chinese and the laissez-fair attitude of the British government which has resulted in the explosive growth of this speck of land soon to revert to the political control of mainland China.

Jan 1, 1993

Measurement of densities, susceptibilities, permanent magnetization, and calculation of demagnetization factors has allowed computer modelling of gravity and magnetic data over the Middleback Range iron formations of South Australia. As well as providing structural information, the study emphasizes the effects of weathering on the interpretation of magnetic data.

Jan 1, 1975

By V. D. del Valle, T. G. Joseph, J. J. Berezan

Aggressive driving patterns, rough and poorly maintained roads and pit floors, along with the occasional bump and poorly placed load from a shovel can create intense and sometimes serious vibration levels on a heavy hauler. The effects of high vibration have been shown to be of concern for the health of the operator as well as the reliability of the equipment. It is proposed that an onboard vibration warning system based on the ISO 2631-1 standard could be used to help operators reduce the vibration levels experienced in a heavy hauler. The onboard system would consist of a screen that displays the instantaneous vibration in the form of three lights: green (safe zone), yellow (cautious zone), and red (danger zone), as well as an overall vibration exposure or dose for the entire shift. With the utilization of the warning system, it is anticipated that the overall vibration levels will be decreased resulting in improved operator health, a reduction of vibration-induced maintenance, and improved haul roads through reduced impact loading and repair for localized trouble areas.

Jan 1, 2004