Search Documents

By P. -É. Boileau, M. Smets, T. Eger, J. Boutin

Long-haul dump (LHD) vehicles used in underground mining are known to expose workers to important levels of whole-body vibration1. These vehicles are generally designed without suspension and may be categorized as small or large LHDs depending on whether their respective load capacities are lower or larger than 3.5 cubic yards. While the majority of older vehicles are equipped with a rigid or unsuspended seat, more recent LHDs often incorporate a suspension seat. The objective of this study was to define the vibration spectral characteristics of most commonly encountered large and small LHD vehicles operating in mining operations. This was done in an effort to categorize the vehicles in terms of vibration spectral classes to be reproduced on a laboratory whole-body vibration simulator to assess the vibration attenuation performance of a typical LHD suspension seat. Methods Vertical vibration measured at the seat attachment point of 8 small and 8 large LHD vehicles operating underground in typical mining operations under loaded and unloaded conditions was considered as the basis for defining the spectral classes. By regrouping the data collected for each LHD vehicle size and load condition, the overall distribution of acceleration power spectral density (PSD) of measured floor vibration was determined over the 0.5 to 20 Hz frequency range. Mean and envelopes of maximum and minimum values of PSD spectra were computed to define the spectral classes, along with the corresponding values of frequency weighted rms acceleration determined in accordance to the ISO 2631-1 standard2. These spectra were further used to calculate the displacements needed to drive a whole-body vibration simulator consisting of a platform supported by two servo-hydraulic actuators having a total stroke of ±100 mm. For validation purposes, the vibration acceleration spectra measured on the simulator were compared with the target spectra representing the spectral classes. Finally, the vibration transmissibility characteristics of a typical suspension seat were determined under sine sweep excitation using both a rigid mass load and a human subject having a mass of 62 kg and 85 kg, respectively. The SEAT value, representing the ratio of seat to base frequency-weighted rms acceleration, was further measured under each of the defined LHD vibration spectral classes by loading the seat with an 85 kg subject. Tests were repeated three times and the mean SEAT values were determined to assess the seat’s ability to reduce exposure to whole-body vibration in LHD vehicles. Results Three spectral classes applicable to both loaded and unloaded conditions were defined as shown in Figure 1: one for large and two for small LHDs. The influence of load on frequency-weighted rms acceleration was found to be negligible for large and Class I small LHDs, while a shift of the peak acceleration PSD to lower frequencies was noted for the loaded vehicles. The influence of load was found to be more important for Class II small LHDs. Table 1 provides a

Jan 6, 2006

Whilst the wider community is both a large consumer of mineral products and relies on mineral exports for much of the wealth which sustains it, the community generally has a poor perception of the minerals industry.   The role of professionals and The AusIMM in the "New Economy" minerals industry is reviewed. The new structure of The Institute is vital as we move forward in times of globalisation, rationalism, increasing litigation, criminalisation of risk and increased focus on corporate governance. This address looks forward to ways The AusIMM and professionals of the future are positioning themselves for these and other challenges.

Jan 1, 2001

By C. M. McKinney

This report contains Bureau of Mines routine analyses of 492 samples of crude petroleum from 470 United States oilfields, each of which produced 2,500 barrels a day or more during at least 1 of the years 1946-56. The fields are listed alphabetically by State and field names in table 1, with information on the geographical and geological sources of the samples. Table 2 summarizes the general characteristics of the crude oils and analytical and computed data determined from the analyses. A previous report 4 contains similar analyses of 283 important United States oilfields; some of them are repeated in this report. Many fields for which analyses previously were published are represented by new analyses, which include data not previously reported. Refractive index nu and specific dispersion, ng minus nD divided by the density, for some of the distillate fractions are included in the analyses of 316 of the crude-oil samples. This is the first Bureau of Mines report on analysis of crude oils to contain such data, and their use in calculating hydrocarbon-type composition of the fractions is explained.

Jan 1, 1957

By D. Harrington

Coal mines and mining-, as well as metal and nonmetallic mines and min¬ing, are not inherently unsafe, although mining people think they are and would like to have everyone else think so. It is now being demonstrated that mines can be operated with essentially as much safety as any other major industrial enterprise; but most mining people, including workers as well as officials, have been slow to realize or admit this. In the past, and with most people even at present, the idea has prevailed that it is utterly impossible to operate a mine without accidents. Although, as in all other kinds of industrial activity, it is true that some injury is likely on occasion to occur to some workers and an extraordinary accident may occur to one or more persons under exceptional conditions, mines can be operated with few if any accidents if a reasonable amount of the right kind of precautionary effort is exerted and kept in effect.

Jan 1, 1934

By William J. Krisko

This contract final report summarizes the design, fabrication and testing of a "line brattice air curtain" device under Bureau of Mines Contract H0357097. The purpose of this program was to develop the concept of using an air curtain for coursing ventilating air parallel with the air curtain From the last open crosscut to the face in exhausting ventilation systems to replace the line brattice cloth in room and pillar coal mining operations. The final design of the air curtain device consists of a 10-foot long closed end pipe with c: slot cut along its length. Pressurized air is delivered to the open end with a hydraulically-driven blower. A sheet of air emanates from the slot and is directed toward the mine roof. An invisible sheet of air is thus created between the top of the machine and mine roof and acts a an extension of the existing conventional line brattice.

Jan 1, 1977

By David R. Macedon

"Through the years, a wide variety of dust control methods have been utilized at mineral processing operations. While some have been successful, many have been highly ineffective. Dust Control systems currently in use include baghouse systems, fog systems, surfactant spray systems, and foam dust suppression. While baghouse systems can be effective, they are capitalintensive and costly to operate and maintain. Chemical dust control programs can be very effective. However, if applied incorrectly, they can have detrimental effect on mineral recovery. Thus, many operations utilize a combination of baghouses and water, often with limited success.Recent advancements in surfactant and polymer chemistry have resulted in substantially improved chemical dust suppression programs. These products range from non-corrosive surfactant/humectant combinations for road dust control to foam-based systems for crushers and transfer points, to advanced polymers for pile binding and soil stabilization. These advances are discussed in detail, citing results from fieldwork in the precious and base metals industries.INTRODUCTIONThe global nature of the mineral processing industry presents a unique set of challenges. Traditional thinking would tell us what works in one place should work in another. This could not be further from the truth in the area of dust control. We learn very quickly that there are a number of factors that can affect the efficiency and success of a dust control program and that these factors are not all chemical or equipment related. Some of these factors include facility maintenance, product selection, water quality and characteristics, and economic considerations.What has been learned from past experience is that each mineral processing plant presents a unique set of factors that will affect the ability to create an optimal dust control program. This paper presents a myriad of treatment options that will highlight the advancements in chemical dust suppression products and equipment."

Jan 1, 2004

Perhaps the most significant development in China's base metal sector is the discovery of major copper porphyries in northern Jiangxi Province and the adjacent southern Anhui Province. At the center of the new exciting district is the proposed Dexing copper complex, located some 350 km east of Nanchang, the provincial capital of Jiangxi. This project represents China's first attempt to put together a major large-scale open-pit operation, comparable in magnitude to Arizona porphyry operations. With the aid of Fluor Mining and Metals, the Chinese plan to develop a 135-175 kt/d open-pit mine, a matching large-scale mill, and the infrastructure needed to accommodate the big operations. An operation of this magnitude would significantly reduce China's import requirements by some 75%. China imports of the red metal are running around 200 kt/a. Under the direction of the Ministry of Metallurgical Industry, the Chinese are currently operating a 10-kt/d mine and mill with equipment primarily of Chinese origin. Dexing engineers told ME that they are considering a possible scale-up to 20 kt/d. How this effort will ultimately jell with the major expansion program is largely a matter of conjecture. Fluor Mining and Metals received a $10-million contract in December 1978 to develop a preliminary engineering and design program. While the original plans called for a 175-kt/d capacity complex, the Chinese subsequently decided to scale it down somewhat. The current proposal is around a 135 kt/d, which would in- elude the existing operation, according to Dexing engineers. Completion of the engineering and design phase is expected by March 1980 and a go-ahead decision will likely be made at that time. The value of the engineering and construction contract is estimated between $800 million and $1 billion. At right, mined ore is dumped 150 m down the mountain to a holding pocket below for rail haulage to the processing plant. Below, a Chinese miner tackles the universal problem of hard toes in the pit with a jack leg. Reserves and Early History The Dexing mineralization consists of three principal ore bodies, including the Chushahung on the north mountain, and the Tungchang and Fuchiawu on the south mountain. Combined ore reserves are estimated by mine geologists at 1.7 Gt of 0.4-0.5% copper. As is characteristic of porphyries, the ore contains important associated values of molybdenum, rhenium, pyrite, gold, and silver. There is also some secondary calcocite and bornite with an oxidized capping. Historically, copper was recovered with iron from the pregnant solutions emanating from the Tungchang deposit as early as the Tang Dynasty (700 AD). Modern day exploration was conducted by the Bureau of Geology in 1956 and reserve figures were es-

Jan 3, 1980

By Brian Reid

"This paper studies the progress made by hydraulic shovel manufacturers over the last few years, particularly in the areas of productivity increase and operating cost reductions.Five years ago, it was widely considered that the unit production cost for a hydraulic shovel in a mining application was double that of a cable shovel in the same application. The hydraulic machine manufacturers have taken up this challenge, and modern improvements in design, coupled with changes in maintenance techniques, have narrowed the gap to the point where it is valid to ask the question ""will the cable shovel exist in ten years' time?"".Historical BackgroundThe history of the cable shovel goes back to the early 19th century and the industrial revolution. Early machines were steam-powered and ran on rails.The ""power shovel"" and the ""dragline"" were the only mechanical means of mass excavation until the early 1950s. Rail-mounted units gave way to crawlers, which increased flexibility considerably. Some shovels were redesigned as backhoes, and some became extremely large when designed as stripping shovels primarily used in North American coal mines.In the early 1950s growth in hydraulic technology spawned the introduction of the hydraulic excavator, which soon began to replace the smaller cable shovels and backhoes used in the construction industry. They were completely self-contained with either a gasoline or diesel engine and, being much lighter, were more readily transportable.As the excavators grew in size from its early models of 0.5 m3 or less, many of the cable shovel models were discontinued. This was not surprising for several reasons, but the most obvious is that both were often made by the same manufacturer."

Jan 1, 1988

By L. W. Hamel

"Two 35 foot diameter enviro clear thickeners were tested in series as CCD units from June until October, 1978. Up to shutdown in July, we ran with automatic bed level control via the level probes and underflow pinch valves. Despite extensive efforts, we were unable to eliminate the surges created between the units by the opening and closing of the pinch valves. Early in July, the best rake speed and gap setting were determined. After shutdown, the enviro clears were run by manually controlling the pinch valves. These efforts were successful.A few mechanical problems were encountered while operating the thickeners. New units should incorporate more support for the drive coupling and a rubber feed seal. A few modifications of the instrumentation control scheme will be required before the units can be fully automated. A less sophisticated automatic flocculant addition system will accomplish the desired results. Control of the underflow withdrawal via the pinch valve should be investigated further. Our best results were obtained by keeping the feed volume to the No. 1 enviro clear constant. Surges were controlled by opening or closing both underflow valves proportionately.Capacity of the enviro clears is dependent of many variables. The ore treated during the test program was much finer than that reported on in R & D Project Report 76-02. Conditions were never steady enough to determine best flocculant dosage or addition point(s). The lowest soluble losses were obtained at very high wash rates. The underflow densities drop but the soluble losses also drop. Regression equations were developed in order to assess the effect of the various parameters. Within the range studied, these equations will predict the performance of enviro clear thickeners as CCD units on Elliot Lake ores. Our results show that the enviro clear thickeners are a viable alternative to the conventional CCD thickener."

Jan 1, 1979

By D Craw

TheSouthern Alps in the South Island of New Zealand are currently rising rapidly as a consequence of continental collision along the Pacific-Australian plate boundary. Rapid uplift has resulted in a major thermal anomaly in the shallow crust beneath the alps. Alpine topography and associated intense precipitation, coupled with the thermal anomaly are responsible for vigorous combined topographic/convective circulation of water through the shallow crust.   Uplift is greatest in a wedge-shaped region between the Alpine Fault and an associated second-order backthrust system, the Main Divide Fault Zone, approximately 20 km to the east. The Main Divide Fault Zone is segmented into NNE and NE striking faults, which are regionally sub-parallel to the Alpine Fault, but dip northwest in the opposite direction. Reverse oblique-slip on the Main Divide Fault is in an easterly direction, with a greater component of strike-slip movement on the NE trending faults. Elevated topography in the Mt Cook region is related to thrusting of a relatively homoclinal sequence of semi-schistose rocks on top of lower-grade greywacke, which controls the position of the Main Divide. Tectonically induced fluid flow resulted in only minor alteration and hydrothermal mineralisation of fault-rocks in Alpine and Main Divide Faults, and localised deposition of quartz and/or carbonate in the immediate hangingwall.   The wedge between the Alpine and Main Divide Faults is segmented by third-order structures north of the Mount Cook region. A series of right-lateral (-085/700S) and left-lateral (-150/600SW) faults, which are synthetic and antithetic to the Alpine Fault, respectively, developed as a conjugate set during uplift. Fluid-flow in the Southern Alps is controlled by these third-order fault/fracture systems. Cu-Au mineralisation, hydrothermal veins, and surface hot spring activity are localised by third-order fault/fractures and appears to be enhanced where conjugates intersect.

Jan 1, 1995

By Robert H. Peters

This Bureau of Mines report describes several significant problems associated with absenteeism among underground coal miners. The vast empirical literature on employee absenteeism is reviewed, and a conceptual model of the factors that cause absenteeism among miners is presented. Portions of this model were empirically tested by performing correlational and multiple regression analyses on data collected from a group of 64 underground coal miners. The results of these tests are presented and discussed.

Jan 1, 1987

By Steven R. Lowe

Construction of a pump station, consisting of an inlet chamber, wet well and pump chamber, required excavation to a depth of 9.7 m (32 ft) below ground surface and more than 7.6 m (25 ft) below the ground water table in a rural, but rapidly developing part of southern New Jersey. Private houses are located [ ] within a few hundred feet of the pump station that use shallow wells for water supply. The pump station design anticipated support of the entire pump station on shallow foundations bearing directly on the underlying natural soils. However, during construction, uncontrolled ground water flow caused ground loss and damage to the bearing qualities of foundation soils. As a result, remedial repairs were required including support of the pump station on drilled pile foundations and releveling of the pump chamber that had settled. This case study is an example of where a poor understanding of the significance of upward flowing ground water had a major impact on the cost of construction. Anticipated subsurface conditions The pump station layout is shown in Fig. 1 with the locations of two borings made prior to construction superimposed. One of the borings was located within the footprint of the deep wet well excavation. Generally, this is not advisable where a deep excavation is required below the ground water table. This is because there is a history of projects where ground water seepage, or pressure, has broken out into an excavation through an ungrouted borehole and compromised the integrity of foundation soils. Logs of the borings did not indicate that the borings [ ] were grouted upon completion.

Jan 1, 2011

By P Landeros, D Benado, J Cornejo, A Pinochet, C Caviedes

In 2005, El Teniente mine began preconditioning the primary rock mass by hydraulic fracturing (HF). The major perceived benefits of this process are a decrease in the magnitude of the expected maximum seismic event and improved cave propagation. In addition, HF has resulted in new information on the propagation pressures of each fracture. Previous studies have attempted to relate propagation pressure to minor principal stress or confining stress.Considering the spatial continuity of propagation pressure and the significant quantity of collected data since the incorporation of the HF technique, minimum requirements for geostatistical modelling have been reached, permitting robust estimates inside the representative volume with acceptable errors (Cornejo, Muñoz and Rojas, 2012; Cornejo and Landeros, 2013). These results are then used to identify zones with higher magnitudes, which are mostly related to more complex geotechnical zones (intrusive and major faults) and caving singularities, making it possible to estimate the spatial extension of these zones.Finally, these results are integrated with other geomechanics aspects to support risk analysis of the mining plan.CITATION:Cornejo, J, Landeros, P, Benado, D, Caviedes, C and Pinochet, A, 2016. Geostatistical modelling of hydraulic fracturing pressures at El Teniente Mine, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 183–190 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By VAN. H. MANNING

Probably no year in the history of the United States showed greater progress in the mineral industries than 1916. Although this progress was undoubtedly stimulated by the war in Europe, which caused extremely high prices for some of the metals, yet the fact remains that mining is being regarded more as a business and less as a speculation, and the benefits of business methods are becoming evident. Practices that were almost universal a few years ago have been largely abolished, the mining public has been brought to recognize the folly of wasteful and dangerous methods, and there is a gratifying unanimity of opinion in regard to the conservation of life and health, as well as of our mineral resources. The people of the United States realize more fully than ever before the extent and value of the country's mineral resources and the possibilities that await intelligent and well-directed efforts at utilization. In the past, economic reasons caused deposits of valuable metals and industrial materials to lie idle; commercial reasons, many of them not truly economic, led to the waste of valuable constituents in many ores; the recovery of minerals from the ground was too often incomplete and accompanied by uncalculated loss; and the treatment of ores in mills and smelters saved altogether too Iowa proportion of the metals sought. Now better methods are being tried on every hand, and the unparalleled record of the year is largely due to the success of these efforts. According to the preliminary estimates of the United States Geological Survey the output of metals and minerals in this country in the calendar year 1916 had a total gross value of slightly more than $3,000,000,000. For many metals and minerals the figures broke all previous records, the new records of some products, as compared with 1915 figures, being as follows:

Jan 1, 1917

When Haematite Explorations Pty. Ltd. began prospecting for petroleum in 1960, there was only ill-defined geological evidence on the land bordering Bass Strait to support the belief that petroleum lay trapped in sedimentary formations beneath its shallow waters.A reconnaissance of the area, made in 1961 by the airborne magnetometer method, covered the waters and islands of the Strait and overlapped the Victorian and Tasmanian coasts. The survey indicated the presence of the Bass Basin (which is completely water-covered), assisted in outlining the Otway and Gippsland Basins, and showed that each basin contains sedimentary rocks over 10,000 ft thick. Information on the regional geology and minor volcanic activity was also obtained.Marine seismic surveys carried out from 1962 to 1965 defined these basins more accurately and showed the nature and structure of the thick sedimentary sections.Correlation of the seismic data with onshore wells identified the sediments as Tertiary and Mesozoic. Subdivisions of the former in all basins and the latter in the Otway Basin were made. These Tertiary and Mesozoic rocks are not seriously deformed and they have good prospects of containing petroleum.Possible structural and stratigraphic traps, recognized from the seismic record sections by petroleum geologists, are being tested by offshore drilling which began in 1964.

Jan 1, 1966

By Michael Day, Paul Kos, Scott Brinton

A hydrogeologic characterization and impact analysis was performed for a proposed quarry at the Hitch Rack Ranch located in the Little Turkey Creek watershed southwest of Colorado Springs, Colorado. Continuous multiple channel tubing, nested piezometers, stream flow measurements, and mapping of known seeps were used to define the three-dimensional potentiometric distribution and areas of groundwater recharge and discharge. Water balance considerations, mass balance calculations, and potentiometric response to earth tides and barometric fluctuations confirmed that the granite fracture system in the ridge area of the proposed quarry has an extremely low bulk hydraulic conductivity resulting in minimal groundwater discharge to sustain the baseflow of Little Turkey Creek. The Little Turkey Creek valley forms the major conduit for groundwater flow exiting from the upper part of watershed underlain by granite. This conclusion has significant implications with respect to mine planning to minimize projected impacts to the hydrologic system and preserve this recharge component to downgradient Denver Basin sedimentary deposits.

By M. J. Papo, A. Muwila

Hercules? is a low nickel austenitic stainless steel developed at Mintek that has a typical composition of 9 wt% Mn, 0.05 wt% C, 2 wt% Ni, 0.25 wt% N and 16.5 wt% Cr. A more corrosion resistant version of Hercules? (Hercules? B) with 0.5 wt% Mo has also been developed. Potentiodynamic tests performed on Hercules? B in a 5 wt% sulphuric acid solution showed it to have improved corrosion resistance comparable to that of AISI 304. The effect of a varying Mn content on the corrosion resistance of Hercules? B has also been investigated and the results discussed in this paper. From the corrosion test results, it is clear that decreasing the Mn content of Hercules? B increased the corrosion rate while increasing it decreased the corrosion rate. KEYWORDS Austenitic stainless steel, %ferrite, molybdenum, manganese, nitrogen, electrochemical corrosion tests, potentiodynamic scans, microstructure, chemical analysis.

Jan 1, 2006

By M Stewart

In January 1994, Macraes Mining Company started a new phase of exploration to find additional resources along strike and down dip of identified resources for a mill that was being expanded from 2.1 Mtpa to 3.2 Mtpa. At 30th June 1997 a total of 456,784 m in 3,627 holes had been drilled at the Macraes Gold Project with approximately 325,000 m in 2,100 holes drilled in the latest phase of exploration. This necessitated the construction of resource estimates on a more frequent basis and resulted in the formation of a resource modelling team, assisted by Snowden of Perth. Since April 1995, 14 separate resource estimates have been completed. At Macraes, resource estimates are built using Medsystem/Minesight software. The geological interpretation is converted into a set of three dimensional wireframed solid models which are used to code drillhole composites and blocks in a block model. The interpolation method of indicator kriging is used to interpolate grade into the blocks. Classification into measured, indicated and inferred categories is on the basis of geological confidence and drill spacing. The resource estimate is reconciled against grade control polygonal estimates on a bench by bench basis and on a monthly basis. Grade control estimates are reconciled monthly to mill production. For the period 30 June 1995 to 30 June 1997, the resource estimates have under predicted tonnes by 4% and grade by 1% to under predict ounces by 5% at a 0.5g/t cut off. At ROM sulphide cutoff grade, the models have over predicted tonnes by 5%, under predicted grade by 5% to over predict ounces by 1%.

Jan 1, 1997

The annual reports of the supervising engineer of the seven sections comprising the Mining Division are assembled in the following pages and form the annual report of the division. In planning activities, the aim has been to adapt the work to changing conditions and needs of the mining industries and to avoid becoming bound to any particular type of investigation when others are found to be of more pressing interest.

Jan 1, 1939

If lead buttons are cupelled under closely controlled conditions in a suitable design of furnace, silver losses during cupellation are given by a simple equation. The effect of copper on these silver losses has been studied and a "copper limit" for cupellation has been determined. Scorification and crucible fusion procedures for copper-bearing materials have been designed so that the lead buttons produced will not contain amounts of copper greater than this determined copper limit. Silver losses during these crucible fusion and scorification procedures are given by the distribution law, and can be calculated. Thus, silver can be determined in copper-bearing materials with a satisfactory degree of accuracy provided that the appropriate corrections for losses are applied to the weight of the silver prill produced.

Jan 1, 1957