Search Documents

By S. K. Kawatra, A. K. Bakshi, T. C. Eisele

An on-line rheometer, suitable for use with slurries, has been developed at Michigan Technological University. This rheometer can be used with both Newtonian and non-Newtonian slurries, and produces complete shear-rate/shear stress curves which characterize the time-independent rheology of the slurry. The sensor utilizes the Hagen-Poiseuille equation and Boyle's Law to calculate the shear rate, slurry flowrate, and shear stress from a series of pressure measurements. The design of the unit allows the measurement sample to be continuously collected from operating process streams in the often-hostile on-line environment. The shear rate/shear stress curves can be used to conveniently calculate the apparent viscosity at any given shear rate, and also to measure any yield stress or other deviations from Newtonian behavior.

Jan 1, 1999

In this paper, uniaxial compression tests were conducted on intact rocks and broken rocks that were reinforced by grouting, and the effects of grouting on the strength of broken rocks were analyzed. The results show that after grouting reinforcement, the bearing capacity of broken rocks with different lithologies increased, and their uniaxial compressive strength recovered by approximately 6%–16%. The results indicated that the stronger the rock, the smaller the strength recovery of the consolidated body formed after grouting. At the same time, using borehole camera observation and deep overburden strata separations, the fracture development characteristics of surrounding rocks of the gob-side retained entry were analyzed and divided into different regions. On this basis, a guided grouting method was proposed; that is, shallow hole grouting was first used in the plastic zone of the broken surrounding rocks to form the isolation layer, and then deep grouting holes were arranged in the elastic-plastic zone of the transition zone to guide the slurry flow to the shallow unfilled zone. Therefore, the broken surrounding rocks were reinforced into an integrated body and selfbearing capacity improved.

Jul 28, 2020

By A. J. Wainwright

The Coffee Creek lode gold discoveries are located in the White Gold district (Dawson Range), west-central Yukon, 130 km south of Dawson City and 30 km south of the Golden Saddle gold deposit (Figure 1). Extensive structurally-controlled gold mineralization has been discovered during the 2010 and 2011 exploration drilling campaigns, highlighting this part of the Dawson Range as a significant emerging gold district. [ ] In this contribution we review the geological framework and describe the mineralization styles and metal signatures observed to date on the Coffee project. The main Coffee area is underlain by a 15 km by 4 km geochemical footprint, characterized by discrete linear gold-in-soil anomalies that correspond to various mineralized corridors. Of several mineralized areas tested in the past two drill seasons by diamond core and reverse-circulation (RC) drilling, we focus on the Supremo, Double Double, Latte and Kona zones; areas with the most information obtained from drilling thus far (Table 1; Figure 2).

Jan 1, 2012

By T. M. “Mike” Gurr

"U. S. marketable phosphate rock production for the 2018 crop year (July 1, 2017 to June 30, 2018) showed an increase to 27.7 Mt (30.5 million st) from the 2017 crop year production of 27.1 Mt (29.8 million st), as reported to the U. S. Department of the Interior by the mining companies operating in the United States during crop year 2018 (Table 1). Domestic consumption decreased in the 2018 crop year to 23.9 Mt (26.3 million st), as compared to the 27.2 Mt (30 million st) consumed in crop year 2017. U.S. imports of phosphate rock increased to 3 Mt (3.3 million st) for the 2018 crop year from the 1.81 Mt (1.9 million st) for crop year 2017. Imports of phosphate rock were from Peru and Morocco. There was an increase of 2.85 Mt (3.1 million st) in producers’ stocks from 7.45 Mt (8.2 million st) in crop year 2017 to 10.3 Mt (11.3 million st) in crop year 2018 (Table I).For calendar year 2018, Florida and North Carolina phosphate rock production accounted for 75 percent of the total U.S. production, with the balance being produced in Idaho and Utah. The Florida and North Carolina percent of U.S. production is declining. U.S. production of 25.7 Mt (28.3 million st) in calendar year 2018 was produced by five companies at 10 mines in four states and accounted for approximately 9.6 percent of the world production of 267.7 Mt (295 million st) for calendar year 2018 (Table 2).In calendar year 2018, U.S. phosphate production decreased by 2.2 Mt (2.4 million st), while companies increased stocks of phosphate rock by 1.7 Mt (1.9 million st). The domestic production for calendar year 2018 of 25.7 Mt (28.3 million st) represents 78.4 percent of the domestic production capacity of 32.8 Mt (36.1 million st).At present, China reportedly produces more than 50 percent of the world’s phosphate rock. As a result of planned expansions, Morocco production has increased from 27 Mt (30 million st) in 2017 to 33 Mt/a (36 million stpy), which is approximately 12.3 percent of the world’s production, moving ahead of the U.S. production. In calendar year 2018, the U.S. phosphate rock production was 25.7 Mt (28.3 million st), which is less than 10 percent of the world’s production of phosphate rock (Fig. 1)."

Aug 1, 2019

By G J. Fleming

The Miwah prospect lies on the dilational 070¦ trending Miwah Lineament near its intersection with northerly oriented fractures within Pliocene volcanic rocks exposed between a NW trending segment of the dextral transcurrent Sumatra Fault, and the more northerly trending Samalanga-Sipopok Fault to the east. These faults reflect the continued interaction between stresses from the India-Australia plate located to the southwest, and spreading within theAndaman Sea to the north of Sumatra. A system of deep seated faults is believed to have facilitated emplacement of post-Miocene magmas and Quaternary volcanic centres at shallow crustal levels throughout northern Sumatra. Miwah mineralisation is associated with variably dipping structurally and lithologically controlled argillic and advanced argillic alteration. An oxidised supergene leached zone and a recent, thin, unaltered tuff blanket partly overlie the mineralisation. Mineralised zones are commonly brecciated and veined, and display quartz, quartz-alunite, quartz-alunite¦pyrophyllite¦kaolinite replacement assemblages, surrounded by more weakly mineralised, often vugghy quartzalunite¦pyrophyllite¦kaolinite advanced argillic, and argillic zones of quartz-kaolinite, quartz¦pyrophyllite¦kaolinite and smectite-illite-quartz. Propylitic assemblages are marginal to more intensely altered zones. Hypogene copper mineralisation is typified by enargite, luzonite, and covellite. The host mineral to gold is uncertain at present. Rare barite, native sulfur, and ?telluride also occur. Bornite and chalcopyrite have been observed in transported altered rocks in faults. Generally the mineralisation is anomalous in precious metals, locally enriched in Cu, erratic in Pb, and depleted in Zn, with a good correlation between Cu-As-Ag.

Jan 1, 1995

By Luis Valle, Fredy Zegarra, Ernesto Vizcardo

El uso de los procesos estocásticos y cadenas de Markov se ha desarrollado solo para estudios de probabilidades en la rama de las ciencias matemáticas y como una opción a las descripciones tradicionales en el campo del procesamiento de minerales, se realizó una comparación entre ambas metodologías para lo cual se cuenta previamente con varios análisis granulométrico proveniente de los molinos de Bolas industriales de la empresa Shougang Perú y pruebas granulometrías de Molienda de Sider-Perú, comparar en ambos estudios, como el probabilístico (Cadenas de Markov) y el cinético (Selección y fractura) ofrecen un buen acercamiento al resultado experimental, dando como una buena alternativa el primero por su uso del manejo estocástico.

Sep 1, 2017

By John Jonkman

The cost of equipment maintenance is the largest single expense at many mines and processing plants. It is not unusual for a maintenance and repair budget to be larger than 50% of the punt's total budget. Generally, in the mining industry, 400-60% of the work force in a plant reports to the maintenance department. Studies have shown that many plant maintenance workers are only 33 to 40% productive, working 2.6 to 3.7 hours of every 8-hour day. In recent years, many companies have begun to recognize that- productivity improvements and cost reductions can he achieved by upgrading maintenance methods. This paper discusses ten common causes of low maintenance productivity and how recent advancements in computing technology can be utilized to address these causes for low productivity.

Jan 1, 1986

The following data cover a phase in the systematic testing of gold deposits which does not appear to have been specificalIy investigated.In boring either secondary or primary deposits, gold, by virtue of its high specific gravity, will tend to migrate downward, below the driving shoe or bit, and thus cause misinterpretation of value unless final recovery Can be effected after the hole has been bottomed.Unlike fortuitous and non-recurrent errors, due to, say, running ground, "pile driving" or rock fractures, systematic error due to migration may be unpredict.able from operating data alone, and, therefore, result in serious miscalculation of the weighted average upon which the engineer's recommendation is based.Applied to diamond drilling, loss by downward migration appears to have been largely responsible for distrust of sludge assays in the past. On the other hand, although modern practice rightly trends towards an integration of both core and sludge samples in borehole valuation, the possibility of systematic loss must be investigated when using combination graphs such as those of Longyear, Moehlman and WeIler. If the sludge value is incorrect the combination graphs will serve solely to stultify the core valuation.It appears to be axiomatic that: 1. With full core, sludge assays are of minor import.2. With recovery above 90%, differentjal grinding, of the high grade sections may have occurred, and this c!ln be corrected only by the us.e of cOJ;rect sludge valuation.3. With core recovery less than, say, 70%, no accurate valuation is possible without integrating the sludge assay.4. With less than, say, 10% core recovery, the sludge assay affords the sole basis of evaluating a borehole which may have cost many hundreds of pounds.The conditions demanded for reliable sludge valuation have, in practice, been restricted to high quantitative recovery and return of nearly 90% of the drill water. It is submitted, however, that the following additional knowledge is required:1. The nature of gold distribution in the ore.2. The lifting power of the return water column, which can be gauged by the maximum quartz particle, provided that the degree of "hindrance" can be determined.3. That all gold has been cleared from the bottom of the borehole immediately after it has passed through the orebody.The three cases discussed hereunder are offered not only as proof of the thesis, but also in the hope of promoting discussion on the interpretation of borehole values and on methods for saving free gold in the sludge. The fact that two of them cover alluvial boringand the third diamond drilling has resulted in this attempt to reduce the behaviour of free gold to a basis common to all types of boring.

Jan 1, 1950

By John Songstead

INTRODUCTION The Bunker Hill mine, located at Kellogg, ID, in the Coeur d'Alene mining district, has been a major pro¬ducer of lead-zinc-silver ore since 1887. Since its dis¬covery, it has produced over 25 401 171 t (28 million st) of ore from 20 to 25 veins and ore zones. The mine now covers an area of approximately 1.609 km (1 mile) in length and 0.8 km (1/2 mile) in width and extends from 1097 m (3600 ft) above sea level to 488 m (1600 ft) below sea level. Production is presently at a rate of 1542 t/d (1700 stpd). During 1965, a new stoping method, the Bunker Hill pillar system, was developed to enable the profitable mining of large, low-grade zinc ore bodies. The system was specifically designed to in¬corporate the Atlas Copco T26GH rubber-tired loaders. High productivities were achieved, and the method was adapted for mining the higher grade stopes where large timber square sets are utilized. This results in nearly 100% extraction. GEOLOGY The area encompassing the Bunker Hill mine lies immediately south of the Osburn fault, a major east-west striking, deep-seated strike slip fault which is the dominant structural feature in the Coeur d'Alene district. The Bunker Hill forms a series of veins and mineralized zones which occur as link structures, tension fractures, and breccia zones in folded, interbedded argillaceous quartzites of the Revett and St. Regis formations of the Precambrian belt series. The Rosco ore body is predominantly a zinc ore body above the Cate fault, which is presently known to occur from the 13 level. [elevation 488 m (1600 ft)] to the 1600 level [elevation 304 m (1000 ft) ]. These ore bodies are stringer zones with at least one dominant 1.8 to 4.5 m (6 to 15 ft) wide band of ore. They dip 0.09 to 0.26 rad (5° to 15°) steeper than the local 0.61 rad (35°) dip of the Cate fault, and also deviate 0.26 to 0.52 rad (15° to 30°) in strike from the Cate. Because of the flat dip and fractured weak hanging wall, normal cut-and-fill mining has not proven practical in this ore body. The mechanized timber methods described in the next section and the Bunker Hill pillar system are the mining methods successfully used. MINING METHODS While pillar stoping and mechanized cut-and-fill stop¬ing methods were obviously superior to the widely used timber stoping methods, as far as cost and productivity

Jan 1, 1982

By David H. Tang

Massive pillar failures were observed at two underground coal mines. The results of stability analysis using traditional pillar design formulae did not agree with the underground observations. Finite element models were used to analyze the causes and mechanisms of the pillar failures. The results were confirmed by the underground observations. Finally, the improved mine plan for each case was derived to ensure the stability of the underground structure.

Jan 1, 1990

Research and Application of Vertical Screw Stirred Mill

Sep 13, 2010

By M. W. Grabinsky

Better in situ performance data is required in order to advance the rational geomechanical design of cemented paste backfill systems. A few in situ test programs have been conducted, but these have suffered from too few measurement locations within the stope and have not used enough different types of transducers to fully capture the information of significance. In this paper the important geomechanical design aspects are listed, the underlying physical phenomena are described, and some previous in situ measurement efforts are reviewed. A new approach to in situ measurement campaigns is then described including measurement techniques, locations, and the logistical aspects of mobilizing transducers in an active mining environment. A work-in-progress is used to illustrate the principles and concepts involved.

May 1, 2007

The following record of the important responsibilities already shouldered by Dr. Ricketts will give some indication of the trust and confidence reposed in him by his colleagues. The Institute is to be congratulated that a man who is already so much engaged should be willing to assume the further responsibility of guiding the Institute's Ship of state during the ensuing year. Louis Davidson Ricketts, who is brother of Professor Palmer or Chamberlaine Ricketts, President of Rensselaer Polytechnic Institute, was born at Elkton, Md., Dec. 19. 1859, was graduated from Princeton University in 1881 with the degree, Bachelor of Science, chosen a Fellow in Chemistry and W. S. Ward Fellow in Economic Geology, and after two years' study given the degree Doctor of Science. Following the completion of Iris work at Princeton, Dr. Ricketts went to Colorado and started to work as a mine surveyor. For the 15 years following, his time was chiefly occupied in reconnaissance work, geological work and mine examination. From 1887 to 1890 Dr. Ricketts was Geologist for Wyoming, and at, the end of that period transferred his operations to the Southwest. where he has since been steadily engaged in large mining projects. He was identified with the acquisition of the property now owned by the Moctezuma Copper Co., a , subsidiary of Phelps, Dodge & Co., at Nacozari, Sonora, Mex. From 1899 to 1901 he was General Manager of the property and during his administration the concentrator and reduction works were completed and the mines put on a dividend-paying basis

Jan 3, 1916

On the 26th of June 2000 a hydraulic fill retaining barricade failed at the Bronzewing mine in Western Australia. The barricade failure resulted in the release of 19,000 m3 of saturated hydraulic fill into the mine and caused the deaths of three miners. Following this tragic accident, the practices and procedures of mines using hydraulic fills came under intense scrutiny by regulatory bodies and mining companies. At this time, the use of hydraulic fill at Normandy?s zinc/copper Scuddles mine was suspended and waste rock became the sole backfill material in use underground. By 2003, development of the adjacent Gossan Hill mine had progressed to a point where a self supporting fill material was required to enable full recovery of high grade ore. Cemented hydraulic fill (CHF) was identified as the optimal fill type and work began on designing appropriate management procedures and controls to ensure the safe implementation. This work included definition of the fill properties, plant design and construction, reticulation system design, design of stope barricades and drainage systems and fill placement control and monitoring practices. CHF placement began on 16th July 2004 and has continued to date. Significant operational experience has since been gained in areas including plant performance, fill product quality assurance, barricade construction, stope drainage and in-situ performance.

May 1, 2007

By A. M. Radigan, W. G. Prast

M.S. Azun The authors' paper did not explain the facts and reasons why state companies are established and what their role is in international industrial mineral trading. Also, I do not agree with the conclusion implying that the main goal for state companies is to capitilize natural resources. Almost all state companies are founded by certain laws and their activities are arranged by state regulations. Their only aim is to operate mineral deposits for their people and to protect the rights of the people. Although some ore deposits, such as nonstrategic or small, may be exploited by privately owned companies, the state has the right to control the operation and production. Activities of state companies may or may not be widened because of the character of the deposits and the importance of the mineral market involved. For some countries, although governments may occasionally change hands, the policy of the mineral trading system is not affected by this change. There is no doubt that any government desires to make more earnings to increase GNP, when it is involved in operating and trading mines. It wants to produce and sell the finished products, instead of unprocessed ones, if possible. When it is known that some mineral deposits are relatively rare, such as Turkish boron deposits, the government can nationalize the mines to control production and affect the market. If there is an abundance of a certain mineral in the market, the government can cut production and set a floor price, such as Canadian potash. Also, when production of a specific mineral is unique, such as Turkish chromite, the price of such mineral may be set by correspondant government. One may add that if some governments with their state companies produce a certain mineral in a larger amount, they may decide to establish a cartel to protect their production and price. These are the facts followed by government-owned state companies and partially government-owned companies. The reason being charge of many deposits by the state companies is always the same: "protect" the mineral rights of the people.

Jan 2, 1984

By Shaw-Shong Liew

This paper presents the processes of investigation, analysis, design, construction and monitoring of soil nail stabilisation work to facilitate a 14.5 m deep excavation at an uncontrolled fill ground. An extensive instrumentation programme had been implemented to monitor the performance of the stabilisation solution, to provide validation for the designed nail resistance and groundwater variation. From the monitoring results, it was proved that the soil nail stabilisation technique is effective for loose saturated fill provided that substantial care is taken during implementation. Construction difficulties, solutions to overcome the problems and lessons learned will be discussed in the paper.

Jan 1, 2006

By J. J. S. Sebastian

The process development described in this report was carried out at the Morgantown Station of the U. S. Bureau of Mines in cooperation with West Virginia University. An experimental laboratory-scale pilot unit to gasify coal dust in entrainment was constructed on the Campus of the University in Morgantown. The enormously accelerated demand for liquid and gaseous fuels and utilization of our immense coal resources require that a low-cost process be developed for the gasification of a wide variety of coals. Such a process would be a major factor in lowering the cost of synthetic liquid fuels. None of the proc3sses developed in Germany prior to and during World War II, such as the Winkler process, the H. Koppers dust gasification process, the Wintershall-Schmalfoldt process, etc., meet all the requirements for a low-cost process under American conditions. Nor has any other process designed and experimentally operated at atmospheric pressure during the post-war period in this country appeared to fulfill all of the necessary conditions for a low-cost process.

Jan 1, 1950

The Pogo Mine, near Delta Junction, Alaska is a new 2500 STPD gold operation. The control system of the mine and milling operations are a hybrid of DCS (Distributed Control System) control and PLC (Programming Logic Controller) control. A DeltaV DCS system serves as the main control and operation platform while the PLCs operate a multitude of vendor specific packages. The communication backbone of the DCS system is a hybrid of star and ring fiber optic topology, which provides reliability and flexibility. The communication between the DCS and PLCs is typically facilitated by serial communication. This communication insures the integrity of the whole control system.

Jan 1, 2008

By Mark S. Sanders

The present study was designed to explore the contribution of organizational climate and management practices to the injury experience in underground coal mines. A cross-lagged panel design was used in which miners from 22 mines completed questionnaires assessing 27 organizational climate, structure, and function dimensions on two occasions, The results strongly support the hypothesis that climate and management practice have casual effect on the incidence of disabling injuries.

Jan 1, 1976

By A. V. S. Meyer

The Colloquium held at Iscor, Pretoria, on 28th June, 1988, had as its objective the need for Quality Management Systems in the industry. Case studies of how problems were identified and solved by the use of such systems were submitted.

Jan 1, 1988