Search Documents

By John R. Eckel

A Iaboratory drilling rig has been devised and placed in operation which permits the application of hydrostatic, terrastatic, and formation pore pressures to a rock sample for drilling under controlled conditions. Calibrated rests of this equipment in-dicate qualitative agreerment with field results on the effect of weight on bit, rotary speed, and rate of circ~~lation on drilling rate. Tests under pressure, using water and air as the drilling fluids, indicate that when drilling saturated limestone samples, a pressure differential between hydrostatic and formation pressure is the only pressure which affects drilling rate. A differential in either direction causes a reduction in rate, but the same diflerential from the wellbore into the formation causes the greater reduction. Also, in lime.stone, air favorably affected drilling rote only when compared to water at high hydrostatic pressurre, all other conditions remaining constant. Large increases in drilling rate with air could be obtained in the laboratory only while drilling a shale, which offered a limited permeability to nitrogen and which could be drilled with a differential from the formation into the wellbore. In general, the magnitude of the changes due to the pressure effect were small compared to changes in drilling rate obtainable by changing either bit weight or rotary speed. INTRODUCTION In the course of Humble's drilling research program, the desirability of investigating several factors which lend themselves to laboratory rather than field study became obvious. Principal reasons for this are the expense involved in field studies and the difficulty of exercising the required degree of control. Of primary importance are investigations of the effect of fluid pressure on rock rate, the effect of pressure on rock drillability, and a study of the fundamental mechanics of rock failure and chip generation. Several years ago some work in the laboratory on the effect of mud properties on drilling rate was re- ported to the API', but the completion of this work and the investigation of the other variables affecting drilling rate required equipment somewhat more elaborate than that used on these earlier tests. This equipment has been assembled to form Humble's Drilling Engineering laboratory. To date only the effect of pressure on rock drillability while using water and air has been investigated, and this work is not yet complete. Facilities are available to investigate the effect of fluid properties on rate of penetration, and information is being assembled on a current basis on the mechanics of drilling. The sequence of presentation in this progress report is somewhat different from that in which the data were obtained since the order of ex-

By B. B. Broms

A method for calculating the bending moment induced in misaligned or bent piles is described, The maximum bending moment varies with the angular rotation between the pile segments, the coefficient of horizontal subgrade reaction of the soil and the flexural rigidity of the piles. A case history involving damages to misaligned 365 x 365 mm square precast concrete piles is described.

Jan 1, 2010

Organization Place Date 1919 American Chemical Society :.... Philadelphia, Pa. Sept. 2-6 National Assn. of Stationary Engineers Huntington, W. Va. Sept. 8 American Peat Society Minneapolis, Minn. Sept. 22-24 American Iron, Steel Electrical Engineers St. Louis, Mo. Sept. 22-26 American Institute of Min. and Met. Engineers. Chicago, Ill. Sept. 22-27 American Steel Treaters' Society, First Annual Convention Chicago, Ill. Sept. 22-27 National Exposition of Chemical Industries.... Chicago, Ill. Sept. 22-27 National Safety Council Cleveland, 0. Sept. 29-Oct. 2

Jan 7, 1919

Organization Place Date 1919 American Chemical Society Philadelphia, Pa. Sept. 2-6 National Assn. of Stationary Engineers Huntington, W. Va. Sept. 8 American Peat Society Minneapolis, Minn. Sept. 22-24 American Iron, Steel Electrical Engineers St. Louis, Mo. Sept. 22-26 American Institute of Min. and Met. Engineers. Chicago, Ill. Sept. 22-27 American Steel Treaters' Society, First Annual Convention Chicago Ill. Sept. 22-27 National Exposition of Chemical Industries.... Chicago, Ill. Sept. 22-27 National Safety Council Cleveland, O. Sept. 29-Oct. 2

Jan 8, 1919

The income of the Institute is derived mainly from dues, advertising in MINING AND METALLURGY and sale of publications. These sources are fortunately supplemented by the interest from invested funds now amounting to over $500,000, a considerable portion constituting endowments for especial purposes. Aside from the medal funds the principal endowments are the James Douglas Fund for support of the Library, the Rocky Mountain Fund and the Seeley W. Mudd Memorial Fund. The income from the two last named is available for the support of research and a variety of other purposes. It is allocated by the Board of Directors upon recommendation of standing committees in each case. An active effort is being made to increase the endowments of the Institute, it being felt that unusual opportunities exist for research and public and professional service through the organization.

Jan 1, 1939

By Shahid Islam, Lucian Bogdan

Deep and large diameter drilled shafts use mostly bundles of Grade 60 (415 MPa) reinforcing bars as longitudinal reinforcement with rebar splices to make it longer. Lower Grade steel requires large number of bars which result in rebar congestion and difficulty in placing concrete. This leads to increased labor cost for fabrication and installation. By utilizing larger size and higher strength threadbar, the congestion of rebar can be reduced significantly and bundling of bars can be avoided. The lap splices are replaced with simple threaded couplers and end hooks are replaced with end terminators. Threadbar conforms to ASTM A615-15 and can be epoxy coated if required for corrosion protection. This paper describes an attractive value engineering of replacing Grade 60 (415 MPa) bundle of rebars with larger diameter Grade 75 (515 MPa), Grade 80 (550 MPa) and Grade 100 (690 MPa) threaded bars and threaded couplers in some specific drilled shaft projects in the USA. INTRODUCTION A drilled shaft which may also be referred to as drilled piers, caissons, cast-in-drilled-hole piles and bored piles is the key element to the foundation of massive structure. They are used for tall buildings, bridges and foundations for other applications such as retaining walls, sound walls, signs, or high mast lighting. Drilled shaft foundations are typically 3 to 12 feet (0.9m to 3.7m) in diameter cast-in-place deep foundation elements constructed in a drilled hole that is stabilized to allow controlled placement of reinforcing steel and concrete. Drilled shafts for transportation structures are commonly used to depths of up to 200 ft (61m) in the USA. Drilled shafts can be installed in a variety of soil and rock profiles, and are most efficiently utilized where a strong bearing layer is present. The reinforcing cage is typically lowered into position within the hole and then concrete placed through the center of the shaft, flowing from bottom to top through the reinforcement to fill the hole.

Jan 1, 2018

The modelling of lithological domains is a critical step in mineral resource and reserve evaluation. Deterministic models rely on an interpretation of the available drill hole data and expert knowledge, but do not account for the uncertainty in the spatial extent of the lithological domains. Instead, probabilistic models based on conditional simulation can be used to map the probabilities of occurrence of the domains within the deposit, which reflect the uncertainty in their presence or absence at unsampled locations. The mineral grade model is then obtained by weighting the predicted grades associated with each lithological domain by the probability of occurrence of this domain. Such an approach accounts for the continuity of the grades proper to each lithological domain and for the uncertainty in the spatial extent of these domains within the deposit. An application to a porphyry copper deposit is presented. Keywords: spatial uncertainty; plurigaussian simulation; geological control; kriging; geostatistics.

Jan 1, 2007

By Donald J. Barnes

There are no producing or developing mines in the study area. The only mineral production was stone from a basalt deposit near Indian View Point. Cinders and sand and gravel have been produced from deposits within 1/2 mi (0.8 km) of the boundary. Stone, sand and gravel, and cinder deposits inside the area are not considered resources because equal or better quality material is found closer to markets. The study area has no known oil and gas, coal, geothermal, or other energy related deposits. However, in 1982 application was filed on 25,000 acres (10,125 ha) of petroleum and on 15,000 acres; (6,0/5 ha) of geothermal leases.

Jan 1, 1983

By Org de Wet

This paper summarises the strategy for selection between a two module coal plant incorporating large, but less equipment, and a three module coal plant with more but smaller equipment. The two options were evaluated in terms of three main categories: ? Size ? size of the equipment and the effect on the process efficiency as well as the difference in physical dimensions of the plant to accommodate the larger equipment; ? Cost ? capital savings between a two and a three module plant, processing the same ROM (run-of-mine) tons per hour (t/hr); and ? Practicality ? in terms of constructability of the plant, safety of using larger equipment and maintainability of the equipment. Decisions that were taken to reduce the risk associated with size, cost and practicality on the chosen option of a two module plant will be highlighted.

Jan 1, 2006

By A. Krishnan

Keywords: Tantalum extraction, SOM Technology, inert anode, membrane stability The Solid Oxide Oxygen Ion conducting Membrane (SOM) technology offers great potential for environment friendly and energy efficient extraction of high-energy content metals. This work was performed to demonstrate the technical and commercial viability of the technology to produce tantalum metal directly from tantalum oxide and ore concentrates using a solid-oxide, oxygen-ion-conducting membrane (SOM). The process can be used to efficiently produce tantalum metal without expensive pre-processing of raw materials and without harmful by products. The work reported in this paper is: the proof that high purity tantalum metal can be produced, study of the electrochemical behavior of the cell and the method to increase membrane stability.

Jan 1, 2005

By R-H Yoon

The MicrocelTM column flotation technology has been developed based on the fundamental understanding that the first-order flotation rate constant increases approximately as the inverse cube of bubble size. In this technology, bubbles in the range of 100-400 pm are generated by pumping aerated slurry through an in-line static mixer. The high-shear agitation provided by the in-line mixer produces small air bubbles without requiring large frother additions. This column has been tested successfully for processing a variety of non-metallic minerals including kaolin clay, graphite, phosphate, and feldspar.

Jan 1, 1993

By A. Lashagri

This paper presents research results on assessment of environmental impact of digging and loading equipment in surface coal mining. Environmental impact is accessed through the equipment exhaust and dust emissions, and sound level. Exhaust emission is related to carbon dioxide (CO2), carbon monoxide (CO), nitrogen oxides (NOx), sulfur oxides (SOx), and volatile organic compounds (VOCs). Dust generation is expressed through the particulate matter PM10 and total suspended particulate matter (TSP), while sound is presented through the sound pressure level. Modeling of environmental impact of digging and loading equipment is conducted in Microsoft Visual Studio.NET software package. This research is a part of a boarder project on development of software system for the selection of productive, cost-efficient and eco-friendly mining systems, which is sponsored by the Appalachian Research Initiatives for Environmental Sciences (ARIES). The research work presented here may be used by mining professionals to aid in quantifying environmental impact of digging and loading equipment and determinate strategies for reducing its overall impact.

Feb 27, 2013

By Stuart McTavish

"Noranda's Goldstream mine is a 1,500 ton per day copper-zinc mine located 60 miles north of Revelstoke, B.C.The orebody which contains 3.69% Cu and 2.69% Zn was discovered in 1972. Construction of the mine and mill was completed in 1982 and start up was achieved in May 1983.This paper will describe the flowsheet and related equipment 1n the crusher and mill, in particular the dewatering section where two Larox pressure filters are used to dry the concentrates.INTRODUCTIONThe Goldstrean property is located 60 miles north of Revelstoke, B.C. in the Goldstream River Valley (Figure #1). It was discovered during the construction of a logging road in 1972. Exploratory drilling was initiated in 1975, and in 1976 a portal was collared to obtain underground data. Samples were taken from the underground workings for metallurgical bench tests and a pilot plant run.Due to economic conditions, the decision to go into production was delayed until 1980. Concentrator construction and underground development progressed simultaneously during 1981 and 1982, and were completed by the end of 1982. Start up of the concentrator was achieved on May 2, 1983.The ore typically contains about 40% sulphides, which are chalcopyrite 10%, sphaletite 6%, pyrrhotite 20%, and pyrite less than 5%. The sulphide minerals have a high degree of intergrowth. Most of the sphalerite occurs in micron sized grains which are embedded in the pyrrhotite and, to a lesser degree in the chalcopyrite. There is also some fine dissemination of the chalcopyrite in the pyrrhotite. The waste rock is made up of about 30% quartz, 20% guange silicates, and 10% carbonates. The ore has a specific gravity of 3.2 and a natural pH of 8.2."

Jan 1, 1985

By George S. Rice

"INTRODUCTION During the past 4 or 5 years the frequent occurrence of bumps in coal mines of the Cumberland field, in Harlan County, Ky., and Wise County, Va., has caused much apprehension among miners and mining officials of that region.These bumps have caused many deaths and injuries, and have been increasing in frequency. Eight men were killed and a number injured by bumps in the first 4 months of 1934. Their unpredictable occurrence and the usual absence of any preliminary warning tremors or sounds, such as ordinarily precede a large fall of roof, cause fear of other bumps and impair the morale of mine workers.Acknowledgments This report on bumps in coal mines of the Cumberland coal field of Kentucky and Virginia is based on an investigation made at the urgent request of .the Harlan County Coal Operators Association, through James F. Bryson, director of safety of the association, to the Director of the United States Bureau of Mines, following a series of disastrous bumps in. Harlan County, Ky., and Wise County, Va. The request was granted and the writer detailed to undertake the investigation, which was made in June 1934.The officials of certain operating companies in the Cumberland field gave every facility for examining the conditions accompanying bumps in their mines. The writer is most grateful to them for the courtesies shown; to J. F. Bryson, to J. F. Davies, district engineer, Safety Division, U. S. Bureau of Mines, who accompanied the writer throughout his trip to the vari¬ous mines and gave him much assistance and detailed information regarding the occurrence of bumps; and to Dr. David White for reviewing the geological descriptions,Definition of Bumps ""Bumps"" are phenomena comparatively rare in the coal fields of the United States and, for that matter, in the coal fields of the world, because for their occurrence certain exceptional natural conditions are required strong, massive strata of sandstone or conglomerate above the coal and a fairly strong floor, as will be described in detail later."

Jan 1, 1935

We present a novel hybrid algorithm for quantifying the ore grade variability that has central importance in ore reserve estimation. The proposed algorithm has three stages: (1) fuzzy clustering, (2) similarity measure, and (3) grade estimation. The method first considers data clustering, and then uses the clustering information for quantifying the ore grades by means of a cumulative point semimadogram function. The method provides a measure of similarity and gives an indication of the regional heterogeneity. In addition, grade estimations can be obtained at different levels of similarity using a weighting function, which is the standard regional dependence function (SRDF). Keywords: Grade, fuzzy clustering, similarity measure, point madogram, weighting function.

Jan 1, 2008

By McHenry Mosier

This paper constitutes the third progress report on a national survey of the use of detachable bits in metal mines. It presents comparative costs of drilling with conventional and detachable bits and describes the operating practice in rock drilling and the reconditioning of drill steel and bits at 10 mines not discussed in previous reports.3/ ACKNOWLEDGMENTS This report has been prepared with the assistance and cooperation of the officials and staff members at the mines visited. Costs and other data at individual mines were developed and furnished by the operators.

Jan 1, 1937

By A T. Yuniar, C A. Brannon, N D. Pascoe, H H. Firdausi

This paper describes the key components of the Grasberg Block Cave (GBC) mine design and the development and construction status of the mine. Drawpoint production from GBC will be initiated in 2018 following the closure of the Grasberg open pit. Full production of 160 000 t/d is planned for 2024, which will make it a 20-year time period between initial access development in 2004 and full production.Diluted ore reserves are about 1 Bt at a grade of 1.0 per cent Cu and 0.78 g/t Au. The mine plans some 2400 drawpoints on a 20 m × 30 m drawbell spacing in a 700 000 m2 footprint using the El Teniente layout. The drawpoint opening sequence includes five production blocks, the first two of which are scheduled to be undercut simultaneously in 2018. Ore is transported using diesel-powered load-haul-dumps to a series of orepasses and then delivered via loading chutes to a rail haulage system, which delivers the ore to a three gyratory crusher complex. Crushed ore is transported to the mill stockpiles via dual inclined conveyors.Development and construction of the substantial fixed facilities are now well underway. Primary access for personnel and materials is via the 6 km Ali Boediardjo (AB) adits. A service shaft will hoist personnel and materials from the AB adits level to the various operating levels. Shaft commissioning is scheduled for late 2015. The rail haulage system installation and construction is in progress and is due to be commissioned in 2017, which is timed to coincide with the commissioning of the ore handling system. Ventilation is provided through a series of large intake and exhaust drifts, and two of the four main fans have been commissioned. A 1600 L/s pumping system will manage drainage from the mine.Other key facilities include separate shops for rail and rubber-tired equipment, warehousing, a powder magazine, a main control centre and an underground concrete batch plant.CITATION:Brannon, C A, Firdausi, H H, Pascoe, N D and Yuniar, A T, 2016. Development and construction update of the Grasberg block cave mine, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 625–634 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By E. P. Youngman

Except possibly by individual natives and Liberians (small specters), is now being carried on in Liberia, according to a late report. definite information is obtainable with respect to the mineral resources of e country, except that iron ores are said to be abundant. Tin, copper, zinc, site, corundum, lead, bitumen or li nite, and diamonds have all been re- parte, but no commercial Geposits are known to have, been found. Gold has been duce, but not in significant amounts, as may be inferred from the customs - rt for Liberia recording the exportation of gold to the value of $4.80 Germany from the port of Cape Mount in 1925. It is not uncommon for atives to come into towns with African gold and valuable minerals, but they e reluctant to sive information concerning then. Some years ago the Liberian Government was seeing a loan in return for oil concessions, but apparently no drilling bea boon don

Jun 1, 1932

By E. Dzingayi

Keywords: Pyrometallurgy, furnace, Bindura, nickel The smelter at Bindura Nickel Corporation processes concentrates from its own mines and other external sources. Concentrates are dried, smelted, and converted to a desulphurised matte (leach alloy) for further processing at the refinery. The smelter comprises a drying plant, submerged arc electric furnace, electrostatic precipitator, and three Peirce-Smith type converters capable of treating 150 000 tonnes of concentrates per year. Concentrates are dried in a rotary coal-fired kiln, blended with fluxes, and smelted in a six-in-line submerged-arc 15MW electric furnace. Slag is tapped and granulated for disposal, and matte is tapped at regular intervals for blowing in Peirce-Smith converters. The paper details the 37-year history of the smelter, including furnace rebuilds and operating parameters as they have evolved in response to changing feed compositions. Special challenges, particularly relating to the treatment of high talc concentrates, are also described.

Jan 1, 2006

By K. Unkug

It is commonly accepted that the tension of roof bolts can be used as a measure of the effectiveness of roof support performance in coal bearing strata. The conceptual base for the assumption originates from beam theory. Roof bolt tension acting across the bedding and other weakness planes increases friction, preventing potential separation and slippage within the roof strata and therefore, increases the stiffness of the roof beam between the open face and the rock-mass enclosed within the anchorage. Thus, it is important to monitor roof bolt tension, especially for research purposes, and consequently many measuring systems were developed based on numerous working principles. Research planned by the Department of Mining Engineering at the University of Kentucky required a large number of tension measuring devices of high precision. These were intended to operate reliably in corrosive mine environment over long periods of time. After evaluating the existing systems, it was decided to develop a new type of roof bolt dynamometer which would fulfill the above requirements at minimal Cost. Nearly one hundred such dynamometers were constructed, calibrated and installed in two underground mines. They remained in service for a period of one Year, producing a valuable database for the Project. In this paper the working principle of this new type of dynamometer will be described and technical considerations and samples of the collected data will be given.

Jan 1, 1986