Search Documents

By D. Loring, J. Almgren

Climax Molybdenum Company’s Henderson Mine is a large panel caving molybdenum mine located about 43 miles west of Denver, Colorado. Three Joy M120-72-880 fans are installed in parallel on the No. 1 exhaust shaft. Throughout the mine’s history, ventilation changes such as the completion of the No. 5 exhaust shaft have decreased the utilization of these fans. To optimize fan performance they have been run with the full complement of 16 blades, down to as few as four blades. Since the completion of ventilation upgrades associated with the Henderson 2000 project, one surface fan has been operated under normal conditions with 10 or 12 blades. With the completion of a new network model of the Henderson ventilation system, a tool was built to develop fan curves for possible future fan configurations and predict future fan performance. This paper describes the tool and its use at Henderson.

Jan 1, 2007

By M. Yavuz

One of the challenging problems for optimization in mining operations is to choose the best equipment among the alternatives. Equipment selection is an important task for mine management due to its operational cost, and is also an integral part of mine planning and design. Equipment selection is not a well-defined process because it involves the interaction of several subjective factors or criteria. Besides, decisions are often complicated and may even embody contradictions. Therefore, equipment selection is considered as a multi-criteria decision-making process, and suitable decision-making methods should be employed in this process. In this study, the loader selection for Aegean Lignite Colliery was made by using both the analytic hierarchy process and Yager’s method. Owing to the misusage of Yager’s method in the past, a new procedure is proposed in this paper for making proper decisions. It is highly recommended in this purposed method that criteria or alternatives should be grouped so as not to exceed the limitations of human performance (nine criteria/alternatives). The most appropriate solution for the loader selection was investigated by obeying this limitation for each method, and the results were compared. At the end of the decision-making process, a sensitivity analysis was applied for each method in order to see how a criterion affects the final decision. The advantages and disadvantages encountered during the application of each decision-making method are presented.

Jan 1, 2015

By Loren R. Anderson

A probabilistic slope stability computer model was developed at Utah State University and independently evaluated by CH2M Hill Consulting Engineers as a design and analysis tool. Volume I of this report describes the model and Volumes III and IV are users manuals for the computer programs. This volume (Volume II) constitutes the report by the CH2M Hill. It includes a description of a field investigation and stability analysis of an existing tailings dam. Based on the results of the analysis, the tailings dam was evaluated for redesign using probabilistic considerations. Conclusions are made regarding the usefulness of the model as a design tool.

Jan 1, 1982

By Pan Shisheng

Amodified load transfer method computing the displacement, axial compression, skin resistance, toe resistance, and other static bearing behaviours of piles, is propoesd in this paper. Through deriving a new concrete computational method with simple integration, many complex factors, such as different soil properties of each layer in layered soil, variation of soil parameters with the changes of the depth, different elastic moduli of piles under different loads, and even different areas in the same pile, can all be easily considered. This method fits in with many types of piles, including friction and point bearing piles, precast and cast-in-situ piles. Observation of static loading test on pile is given, and the computed values from the modified load transfer method are found to agree with practical measured results.

Jan 1, 1991

This paper is intended partly as a summary of the conclusions that have been arrived at by various authorities on this matter, and also with a view to initiate some discussion on the subject, especially as most of the quartz gold mines in Victoria are operated without having any proper assay plans or any idea of the real values other than those given by the mining managers, who, from experience in the particular cases, are supposed to be able to arrive at a correct idea of the true values of- the ore, and, in many cases, oppose any other methods than their own, holding the view that no sampling is equal in correctness to the bulk sample of the battery. The necessity of properly sampling and estimating the ore in a mine in every case, perhaps hardly needs to be urged on the members of the Institute, but is not, apparently, so obvious to others.It is proposed to confine this paper to the sampling of ore reserves in a mine, and the various points which have to be taken into consideration in arriving at values, from the assayer's point of view, leaving the methods of sampling metallurgical products out of consideration for the present. "It is advisable to define" ore reserves" as ore exposed on three sides at least, and accessible to the sampler on all three. "Prospective ore" would include all ore not so fully exposed; but which may, from the nature of the case, and the geological conditions prevailing, be reasonably supposed to exist.

Jan 1, 1904

By Tom Szaraz, Steve Skelhorn

Part of a major sewer expansion for the City of Columbus, Ohio. The Big Walnut Outfall Augmentation Sewer (BWOAS) consists of 4,000m (13,200 ft) of 3.66m (12 ft)diameter tunnel passing mainly through glacial deposits with a water head of up to 2 bar. The project involves many new innovations, including: Slurry wall work shaft with excavation below the water table; Hybrid universal rings combining traditional steel reinforcement with fibers; New, full EPB Lovat TBM; Two component grout system pumped to the TBM from the surface; and, Linabond corrosion protection liner. The paper looks at the planning approach adopted to meet the various challenges presented, combined with an overview of progress to date.

Jan 1, 2007

By A. Tosun

Muckpile fragmentation formed by blasting depends on the specific charge factor, the discontinuities in the rock mass, and the rock strength. Determination of the discontinuity characteristics and rock strength is a long and difficult process. These two parameters are directly associated with the rock drilling speed. Therefore, it is the drilling speed of the machine used for the blast-hole, rather than the blasthole discontinuity characteristics and rock strength parameters, that is used in the prediction of muckpile fragmentation before blasting. Primarily, it has been suggested that the muckpile fragmentation values can be correctly determined by establishing correlations between the efficiency of the loader and muck pile fragmentation, since fragmentation is directly correlated with the former parameter. Subsequently, a correlation predicting the drilling speed of the drill machine was developed according to the discontinuity characteristics of the blasting surface and the rock strength. Finally, a correlation was developed predicting muckpile fragmentation according to the specific charge factor and the drilling speed of the drill machine The data was obtained by conducting blasting tests in two different limestone quarries.

Nov 30, 2022

By Whitmore R. L

The action of water on a number of Queensland shales which are associated with particular coal measures and oil shales has been studied. The results suggest that the disintegration of some of the shales could cause significant problems in mining and preparation operations. The extent of shale breakdown varies widely from deposit to deposit and from seam to seam but a suitable assessment procedure utilises the test described in AS 1661-1979, and an improved method of presenting the results is described in the paper.

Jan 1, 1982

By Walter Kauenhowen

GeRmany's crude-oil production during 1936 totaled 3,112,494 bbl., an increase of 5.2 per cent over the 3,007,711 bbl. produced in 1935. The official monthly production figures published in 1936 report only the individual production figures of the three old established fields, whereas since 1936 official reports combine the production of all other fields into one figure. According to these published data, and using a conversion factor of 1 metric ton equaling 7 bbl., the oil production of Germany in 1936 was as follows:

Jan 1, 1937

By B. C. Vargas

The Toulon tunnel project is a key component of the Highway corridor on the French Riviera between Marseille and Nice and is a fundamental transportation infrastructure for the region. The first design studies started in the 1960?s. The tunnel project is made of 2 separate tunnels: South and North tunnel. The North tunnel was built between 1992 and 2002 after 10 years of difficult construction (for example, on March 15th, 1996, a collapse of the tunnel in the ?Marchand Area? generated a sink hole in the city Center, causing 20 months delay). The South tunnel alignment runs parallel to the North tunnel at the same depth below Toulon historical downtown (20 to 40m depth with some areas with less than 10m of cover). The Risk management program was studied to be a State of the Art program in urban tunneling construction. The Hydro Geological Context The whole project area is covered with backfills and colluviums of 1 to 4m thick. The Schist, marls and sandstones, randomly distributed along the alignment below the first layer have different characteristics. While the Schist are pretty compact, the marls are fractured. The other layers have very different characteristics, and many faults are located along the alignment, especially in the limestones. The Breccia are heavily decompressed and deformable, as well as the other soils located in the Marchand Area. This 80m long area is where the settlements need to be controlled with an extensive monitoring program. The complete Geological profile is presented in Figure 1. [ ]

Jan 1, 2012

By J. S. Meyer

Although salmonid fishes (including Pacific salmon and trout) have only intermediate sensitivity to copper (Cu) for traditional toxicity endpoints (survival, growth, and reproduction) and thus do not ?drive? the freshwater Cu criteria (e.g., see species-sensitivity ranking in US EPA 2007), Cu concentrations as low as 1 to 2 µg/L have been reported to impair olfaction (the sense of smell) in salmonids in laboratory experiments using dilute fresh water (see references in Meyer and Adams 2010 and DeForest et al. 2011). Olfaction is crucial to predator avoidance, recognition of kin, and reproductive synchronization (Baldwin et al. 2003); and Cu is of general ecotoxicological concern because it can be present in acid/mine rock drainage, industrial and municipal effluents, agricultural runoff, and urban stormwater runoff (Meyer et al. 2007). Therefore, there is public concern that the current regulation of Cu in surface waters is not stringent enough to protect salmonid fishes against olfactory impairment (e.g., OSU 2007; Pearson 2007). Because the toxicity of metals to aquatic organisms is a function of water chemistry [e.g., acute toxicity of Cu generally decreases as pH, water hardness (Ca2+ + Mg2+), alkalinity, and dissolved organic carbon (DOC) concentrations increase; Meyer et al. 2007], hardness-based freshwater criteria for metals are lower at lower water hardness. The recently-developed biotic ligand model (BLM) explicitly takes into account all four of those water chemistry parameters and the concentrations of other major inorganic cations (Na+, K+) and anions (Cl-, SO42-) to predict the acute toxicity of cationic metals (e.g., Ag, Cd, Cu, Ni, Pb, Zn) to aquatic organisms; and the BLM has been adopted by the U.S. Environmental Protection Agency (US EPA) to calculate acute and chronic national freshwater criteria for Cu (US EPA 2007). Consistent with observations of Cu toxicity to aquatic organisms, BLM-based Cu criteria generally are lower at lower pH, water hardness, alkalinity, and DOC concentrations. Therefore, although threshold concentrations for olfactory impairment by Cu can be low in dilute fresh waters, the corresponding hardness-based and BLM-based Cu criteria for the same waters also tend to be low. This leads to a logical question: Are Cu criteria already protective against impairment of olfaction in salmonid fishes, thus obviating the need to decrease those criteria even lower to protect against adverse effects to this physiological/ecotoxicological endpoint? Herein, we demonstrate that in all studies conducted to date, the US EPA?s BLM-based freshwater Cu criteria would have been protective against olfactory impairment in salmonid fishes, but the US EPA?s hardness-based criteria would not always have been protective. This distinction is important because all 50 States in the USA still use hardness-based Cu criteria in their water quality standards, and only some of the States allow use of the BLM to calculate site-specific Cu criteria. Additionally, in the absence of empirical results for calibration of a saltwater Cu-olfactory model, we demonstrate that a proposed unified freshwater-saltwater Cu-olfactory BLM predicts the US EPA?s current saltwater Cu criteria would be protective against olfactory impairment caused by Cu in sea water.

Feb 27, 2013

By S. K. Kawatra, J. A. Halt

"Low-grade iron ores are finely ground and processed to recover iron-bearing minerals. However, the iron-rich powder is too fine to be used directly in blast furnaces and most direct reduction furnaces, and must be agglomerated or pelletized into a usable product called “pellets.” Bentonite clay has traditionally been used as a binder to make iron ore concentrate pellets, but it is expensive and contaminates the pellets. Organic binders may be a viable alternative to bentonite clay. This manuscript reviews organic materials that have been used to make iron ore concentrate pellets. Included are discussions on the development of organic binders, common pros and cons to organic binder use, organic binder structure and its effects on agglomeration, and additives to organic binders.IntroductionIron ore agglomeration turns finely disseminated, low-grade iron ores into a usable product, called pellets. During pellet production, fine-grained, iron-rich minerals are liberated from low-grade ores, concentrated, and agglomerated into round balls that are thermally hardened or cold-bonded to form pellets. Pellets are then transported to blast furnaces or direct reduction operations where they are used to produce iron; iron is further refined and shaped into the wide variety of steel-based industrial and consumer products in use today.Over the years, pellet production has become increasingly more prevalent with the increased exploitation of low-grade iron ores and increased iron and steel consumption around the world. In 2010, world iron ore pellet production was 388 Mt. It could be argued that the current pellet production process has been enabled by the use of binders – practical experience has shown that it would be nearly impossible to agglomerate iron ore concentrates using rotary drums and discs without using a binder."

Jan 1, 2015

By José Arango

La Planta Hidrometalúrgica de Cerro Verde tiene como objetivo alcanzar la máxima calidad en cada uno de sus procesos operativos. Para ello, desarrolla un diseño que permita la transformación del control remoto a una operación automática, generando decisiones lógicas. En ese sentido, el presente texto señala la importancia de los Sistemas de información de operaciones en el sistema de automatización de Cerro Verde - en tanto es soporte de la implementación de un completo sistema de instrumentación y de la instalación de una red de PLC’s que colectan la información y en base a esta, desarrollan una lógica de operación manteniendo interconectados todos los circuitos operativos. Posteriormente, con el uso de software se crea una interfase de conexión entre la red industrial y la red Administrativa, permitiendo adjuntar la información en una base de datos que junto a la otra base administrativa, constituyen un ERP que da vitalidad a nuestra operación. De forma que los sistemas de informacion instalados en Cerro Verde consideran a los sistemas de instrumentación como los ojos del operador de planta.

Jul 17, 2000

By B. M. Loftus

An investigation into the use of impinging stream (jet) reactors for the leaching of a free milling ore produced an increase in gold recovery by 10% while decreasing leaching time by up to 90%.Tests on refractory ores demonstrate no apparent improvement in recovery. However, leaching kinetics are dramatically increased when these ores are subjected to jet reaction prior to agitation.

Jan 1, 1997

By Christopher J. Bise

The objectives for the research project, "Coal Mine Injury Analysis: A Model for Reduction Through Training," were to identify and develop a means to indicate deficiences in human performance, job skills, and/or knowledge at a given mine site that are amenable to alleviation through training or job redesign, and to provide ;I set of analytical tools and training resources that will enable mine training personnel to effectively incorporate the noted deficiencies into a personalized model training program. The findings of this research project are contained in Light separate volumes. Volume I represents the Executive Summary of the study and provides a broad overview of the project's individual areas of emphasis and deliverables. The additional eight volumes provide greater detail on the development of a Model Mine Training Program based upon Professional Database Analysis, Incident Reporting, Loss Control, Job Safety Analysis, Risk Assessment, Cost/Benefit Analysis, and Mine Safety Management.

Jan 1, 1993

By Osvaldo A. Bascur

Intelligent systems (IS) technologies have received much attention in a wide range of process engineering applications including process operations. With the revolutionary progress in information and computer technologies applying the latest technologies in metallurgical complexes has become a serious challenge to both management and technical teams. Objects and components are changing the way everyone relates to their computer and networks. Goals of real time performance monitoring includes maximizing the profitability by maximizing production, improving efficiency, attending product quality, costs, maintenance, environmental and safety regulations. Designers must consider the greatly expanded desktop computing, Microsoft object technology, Internet and how to build these systems. This paper discusses some opportunities and challenges using objects, components in designing applications and integrating intelligent systems tools. Two examples using performance equations and IS technologies applied to mineral processing are presented.

Jan 1, 1997

By Brad Simser

The Brunswick No. 12 Mine is a 10 000 tonne per day producer of lead-zinc-copper-silver ore that has been in operation since 1964. Mining of this multiple lens deposit is primarily by blasthole stoping techniques between 400m and 1200m below surface. The combination of a high overall extraction ratio and high horizontal stresses (twice the vertical) has elevated the induced stress regime to levels comparable to much deeper operations. Improved mine design, and a better understanding of how the rock mass responds to mining in high stress environments is essential to improve overall recoveries and maintain safety. Seismic monitoring has proven to be an essential tool at Brunswick, for both short-term safety of workers, and long-term strategic planning. Practical case studies illustrate how seismic data, particularly source parameter information, can be used to measure the rockmass response to mining and improve mining layouts in difficult regions. As the global trend continues towards mining in deeper, higher stress environments (e.g. South African Witswatersrand Basin, Sudbury Basin) and as local extraction and thus ground stresses continue to increase in existing deposits, seismic monitoring will play a critical role in mining safely and economically.

May 1, 2003

By Yi Luo

A longwall mining operation went under a tall, self-supporting and free-standing wireless communication transmission tower. In anticipation of that the ground subsidence process might affect the transmission tower, the mining company took a proactive approach to mitigate the expected subsidence influences. The efforts include prediction of surface subsidence process at the location of the tower, assessment of stability, structural integrity and functionality of the tower structures, and design and implementation of mitigation measures. The intension of this paper is to demonstrate the techniques that can be used to assess and mitigate the subsidence effects on tall self-supporting and free standing tower structures.

Jan 1, 2008

By L. Bircumshaw

Paper written on project work carried out in partial fulfilment of BSc (Eng) (Chemical) degree This paper details the formulation of a mathematical model for the simulation of a primary bioleach reactor, with specific reference to the leaching of pyrite. The model is based on the direct reaction mechanism, where the leaching of pyrite is said to occur via a two-step process. The process involves the formation of ferrous?iron through the chemical leaching of pyrite and subsequent bacterial oxidation of ferrous-iron back into ferric-iron. At steady state the rate of chemical leaching and bacterial oxidation are linked by the ratio of ferrous-iron to ferric-iron in solution. The extent of conversion of pyrite in the reactor system is described using the segregated flow model, with the exit age distribution of the solid phase being described by the Tanks-in-Series model. The final phase in model formulation involves the inclusion of steady state material balances on the bacteria and fluid phase components. The model is compared to pilot plant data and laboratory data for two different types of pyrite concentrates, with simulation results showing that the model is in good agreement with the data. Author key words: Bioleaching; pyrite; primary reactor; modeling; segregated-flow model; tanks-in series model.

Jan 1, 2006

By Eugene T. Sheridan

The 24th annual survey of the peat industry by the Bureau of Mines, United States Department of the Interior, revealed that 76 producers in 20 States reported commercial production of peat in 1957. In addition to the States that reported production in 1956, Colorado, Idaho, and Wisconsin produced peat in 1957 Forty-four producers reported humus production; 21, reed-sedge peat; and 22, moss peat production. This total exceeds the number of active plants but several producers recovered more than one type of peat. Fifty percent of the total production was reported as reed-sedge peat, 36 percent as humus, and 14 percent as moss peat. About one-sixth of the total production was raw peat, with no preparation other than being air-dried. The remainder consisted of processed peat prepared for use by cultivation, shredding, and/or kiln drying.

Jan 1, 1958