Search Documents

By J. I. Schoenherr, G. Schubert, F. Demczenko

The currently known and used plastics and rubber recycling or sorting processes cannot be applied efficiently and economically due to large amounts of fine bulky materials (<3 mm). These wastes are mostly given to specialized landfill sites. Starting out from classical and traditional beneficiation processes a new research project was initiated to work on certain new ways to efficiently separate plastic material mixes. First basic results show that the use of new and improved thermal beneficiation methods is a great implementation in the field of plastics separation. The results can be further increased by a suitable combination with other methods as well. This leads to high-quality and almost pure separated plastics and rubber products, easy to sell on recycling product markets.

Jan 1, 2002

Objective To reduce dust generated from soiled floors within enclosed operator cabs. Background Enclosed operator cabs are widely used on mobile excavation equipment in the mining and construction industries. They protect the operator from bad weather, noise, and airborne dusts. The inside cab environment usually must be kept at very low dust concentrations because of quartz dust generated from the excavation of silica-bearing rock. For cabs to be effective in controlling airborne respirable dust, they must have an efficient air filtration system, while providing a positive pressurization of the cab interior. Ideally, the recirculated and exterior makeup air filtration should provide at least 99% capture efficiency for dust particles as small as 0.3-µmaerodynamic diameters. Many of these enclosed cabs use heating units mounted or directed along the floor (see figure 1), which can cause dust entrainment problems. Prior studies by the National Institute for Occupational Safety and Health (NIOSH) of enclosed cabs have shown that these floor heaters can generate notable amounts of dust within the cab enclosure (see Technology News 486). Multiple-shift dust levels measured inside a drill cab increased on average from0.04 mg/m3 during the summer months to 0.68 mg/m3 during the winter months. Additional dust level measurements, made with optical particle counters during a nondrilling time period, verified that dust levels inside the cab increased from 0.03 to 0.26 mg/m3when the floor heater/fan was turned on. Dust levels within the cab also became greater than the ambient air dust levels outside of the cab when the floor heater was turned on during the nondrilling time period. This shows that the floor heater was a notable dust source problem. Cab floors are commonly soiled from operators tracking dirt inside the cab upon entering from the mine or construction site. Interior cab dust levels can be increased by (1) airflow disturbance of the soiled floor or (2) operator disturbance of the soiled floor. Approach During prior NIOSH surveys of surface coal mine drills, several drills with very low cab dust levels (#0.1 mg/m3) were observed to have floor sweeping compound spread out over the cab floor during the working shift. This initial observation led to a more controlled A-B study of the effect of the sweeping compound on the interior cab dust levels. This study involved dust sampling with and without sweeping compound inside the cabs of a bulldozer and two drills. Sweeping compounds commonly use sawdust or cellulose as the main bulk material, with oil or wax added for dust adhesion purposes. Sand is sometimes added to increase bulk density. Sweeping compounds with sand are commonly used to sweep up concrete floors. Those without sand (usually referred to as "gritless") are used to sweep up smooth finished floors. Most of the oils and waxes used for the adhesive ingredient are petroleum-base and can have an irritating odor. People sensitized to petroleum distillates could have allergic reactions to these sweeping compounds. A few companies offer non petroleum-base sweeping compounds, using either a natural oil or chemical additive for dust adhesion. During this study, it was decided that only the gritless sweeping compound (without sand) would be used, eliminating the addition of another potential silica source inside the cab. Since the sweeping compound would be applied on the enclosed cab floor for the duration of the shift, it was decided to use a canola oil-base sweeping compound to eliminate irritating odor from the petroleum-base sweeping compounds. The natural canola oil-base sweeping compound had a slight woody scent. The three pieces of equipment used in this study had notably different cab layouts. The bulldozer had a small cab with vents discharging air-conditioned or heated air from adjustable louvers at operator waist level and floor level. The bulldozer also had a cloth fabric seat and a carpeted floor. Drill A had a large cab with the heat directed from adjustable louvers at operator knee level and the air-conditioned air directed from cabin ceiling louvers. This drill had a vinyl fabric seat and a steel plate floor. Drill B had a small cabin with the heat directed across the floor (see figure 1) and the air-conditioned air directed down from the ceiling. It had a vinyl fabric seat and a worn rubber mat on a steel floor.

May 1, 2001

I report results of over 850 microprobe analyses of sulfides, sulfosalts and electrum from the Favona adularia-sericite epithermal deposit of the Waihi district in the southern Hauraki Goldfield of New Zealand. Pyrite and marcasite from altered wall rocks that enclose the veins are stoichiometric, with compositions of FeS2, and no significant trace elements. In contrast, pyrite in veins commonly contains appreciable As (up to 3.2 wt per cent), and locally contains several tenths of a percent of Cu, Zn, Co, Ag and Sb. Vein pyrite may contain up to 0.22 per cent Au, but Au contents do not show a positive correlation with As. Limited electrum data indicate that it ranges from Ag0.47 Au0.53 to Ag0.54Au0.41Cu0.01Zn0.04. Chalcopyrite is stoichiometric CuFeS2, and most galena is PbS, but some galena contains up to 4.4 wt per cent Se, which substitutes for S in its lattice. The galena is not argentiferous; the highest Ag content is 0.45 wt per cent Ag. Sphalerite averages 4 mol per cent FeS, but ranges up to 15 mol per cent. Tetrahedrites [(Cu,Ag)10(Zn,Fe)2(As,Sb)4S13] show variable substitution, but most are Cu- Zn- and Sb-rich. Veins also contain aguilarite (Ag4SeS), stromeyerite (CuAgS), naumannite (Ag2Se), and mckinstryite [(Ag,Cu)2S].

Jan 1, 2004

By Irving Hartmann

Rock-dusting of coal mines is a most important safety measure for preventing or limiting the propagation of explosions. The Bureau of Mines has recommended for many years that rock dust be distributed on the top, ribs, and floor of mine entries and other workings of all bituminous coal and lignite mines in sufficient quantities to maintain the incombustible content of the dust above the minimum requirements. Rock-dust barriers constitute a secondary safeguard used occasionally to complement generalized rock dusting at entrances to panels and side entries or at other locations. In general, rock dust can be applied effectively with modern rock-dusting machines. However, in thin coal beds, in certain back entries, and in some other areas, rock-dusting machines cannot be used conveniently. Furthermore, many small mines find the purchase of machines costly. In such cases, rock dust is not used at all, or else it is distributed by hand, a relatively slow and costly procedure. In recent years some coal mines have started applying rock dust with the aid of permissible explosives. This may be done in various ways. One method consists in placing a stick of explosive on the floor of a room or entry midway between the ribs and covering the stick with two bags of rock dust that are slit on top and set crosswise one above the other. The explosive is then fired, causing the rock dust to be distributed on the nearby roof, rib, and floor surfaces. The procedure is repeated at desired intervals until the entire area is rock dusted. The method is claimed to be rapid, safe, and inexpensive.

Jan 1, 1950

By James A. Brown, Marius Botha, Christopher A. Fleming

"The technical and economic feasibility or re-processing hundreds of millions of tons of tailings in a number of historic gold tailings dams in the Witwatersrand area of South Africa is being investigated. The objective is to recover uranium and residual gold from the tailings, as well as to oxidize the sulphides to eliminate long term environmental liabilities associated with acid mine drainage. The tailings from the re-processing plant will be re-deposited in a new area far from urbanization, allowing for the rehabilitation of the real estate currently occupied by these historic tailings.The first step in the process involves a mild-regrind and mild acid leach of the tailings (pH 2.5 to 3.0) to dissolve up to 40% of the uranium. This uranium is recovered directly from the pulp by resin in pulp (RIP) with a strong base resin. The RIP tails are then treated by flotation to recover a rougher pyrite concentrate, and flotation tailings that are discarded. The rougher concentrate is cleaned to produce a final pyrite concentrate and cleaner scavenger tailings, and the pyrite concentrate is oxidized in an autoclave to leach uranium and generate acid. The autoclave discharge is combined with the cleaner scavenger tails, and the acid and ferric ions generated in the autoclave are used to leach more uranium and oxidize more sulphide in the cleaner tails. The product from the concentrate leach circuit is processed by resin in pulp for uranium recovery, followed by neutralization, cyanidation and carbon in pulp for gold recovery.The rougher float tails may be further treated to recover gold that was not recovered in flotation, but which had been liberated from the old dumps by natural oxidation of some of the pyrite over many decades. The float tails would be neutralized and treated by cyanidation and CIL to recover this liberated gold.All parts of the flowsheet have been extensively tested in the laboratory, and the critical elements of flotation, pressure oxidation and resin in pulp have been demonstrated in pilot plants. The results of the hydrometallurgical investigations are presented here."

Jan 1, 2010

By F. J. Sotillo

The reduction in energy consumption has been always important for beneficiation plants. Also gravity separation processes have gained lately great importance due to environmental concerns, especially in the gold and silver Industries. In this sense, the paper point out how to reduce the energy consumption in grinding, and increase efficiency in both grinding and gravity separation are of utmost importance to optimize the use of the country’s resources. For these purposes, chemical additives, such as rheology modifiers have shown great potential, and deserved careful consideration.

Sep 9, 2007

By S. Felderhof, W. S. Vaughan

"Over the years, it has been increasingly difficult for the minerals industry to raise the necessary capital for its activities. To alleviate this phenomenon, complete transparency and capital market efficiency is needed. Since a company’s mineral resources and mineral reserves base is an essential component to obtaining capital, reporting these assets must also be transparent and efficient. This must occur, however, at an international level given that mineral industry operations, and its financing, are international. To achieve this, an international committee (i.e. Australia, Canada, South Africa, the United Kingdom and Europe, and the United States) was formed and has been developing standards for the reporting of mineral resources and mineral reserves.The effectiveness of these standards, however, depends on adoption by the required regulators. Unfortunately, these standards have not been recognized by the U.S. Securities and Exchange Commission (SEC). Instead, the SEC adheres to its old standard (Industry Guide 7), making it increasingly expensive and difficult for international mining companies to obtain capital in the United States. Compounding the problem is the SEC’s influence over the current work of the International Accounting Standards Board and the International Organization Organization of Securities Commissions. These organizations are in the process of standardizing international accounting practices and international securities rules and regulations. Their current position may prevent adoption of the industry-developed mineral resources and mineral reserves standards which are internationally recognized."

Jan 1, 2005

By A. Bhattacherjee

The Shewhart [X]?and R charts are still the most popular control charts in use today for continuous monitoring of quality data. However, for these charts to function properly, the underlying assumption of normality and independence of data must be satisfied. When either independence and/or normality of data are not present, which is a common feature of ore quality data, an application of the conventional Shewhart [X]?and R charts may introduce false alarms in the analysis of the data. To address these issues, a guideline is proposed for construction of appropriate univariate and multivariate control charts for a variety of situations. A use of this guideline to a bauxite mine suggested the construction of special cause control chart for the analysis of individual variables namely, Al2O3% and SiO2%; whereas, the multivariate T2 chart based on residuals is proposed for the bivariate analysis of the variables. The case study clearly revealed that without considering the data correlation, one may be in a state of false impression about an out of control condition while using the Shewhart [X]?and R charts for univariate and the Hotelling T2chart for multivariate analysis. To compare the effectiveness of the control charts, specifically the Shewhart [X]?and the special cause control charts, a simulation study was conducted. It was found that the conventional Shewhart chart provided lower probability of coverage than the special cause control chart. It was also revealed that the quality specification of Al2O3% is met as the variation of Al2O3% is well within the specification limits; whereas, it is difficult to meet the quality specification of SiO2% on a regular basis.

Jan 1, 2002

By C. A. Herbert

This paper sets forth the hazards of accumulations of explosive mixtures of methane and air due to inadequate ventilation, the causes of which are discussed as follows: 1. Lack of well-maintained air courses. 2. Air losses due to leaky stoppings, trap doors, and overcasts. 3. Faulty mining methods. 4. Poor supervision. A modified plan of room-and-pillar panel mine development is suggested, which, it is believed, will eliminate many off the hazards of gas accumulations inherent in the present method of mine development. It is also suggested that some water-proofing agent be used on the roof of permanent air-course entries in conjunction with roof bolting to eliminate the detrimental effect of the moisture-laden atmosphere during summer and thus prevent serious roof falls.

Jan 1, 1953

By Doyle A. Ellerbruch

An FM-CW microwave system was investigated for measuring coal layer thickness. Measurements were made in three different mines near Pittsburgh, Pennsylvania, near Fairview, West Virginia, and near Coffeen, Illinois. Microwave frequencies in the range 1-2 GHz were used to measure samples up to 55 cm thick. All samples were backed with a naturally occurring shale. Measurements were also made on coal and shale samples compounded in the laboratory at the Bureau of Mines Pittsburgh Mining and Safety Research Center near Bruceton, Pennsylvania. The results indicate that layer thickness can be determined in most cases, although large anomalies may, in some cases, produce misleading results. Many anomalies that were detected with the FM-CW system were verified visually by drilling into the coal layer. The dielectric constant of coal apparently varies significantly within a coal seam. The form of the output signals from the FM-CW system seem to simplify the data interpretation and analysis process as compared to the manually swept microwave system used previously. It appears that this technique has the potential of measuring changes in the dielectric constant of a coal seam and providing an output that can be used for real-time corrections in layer thickness; measurement.

Jan 1, 1976

By Lewis Martin

Whereas many researchers and mine engineers have conducted tests using different types of grout, grout ratios, and physical modifications of the cable to determine cable bolt load characteristics, few studies have been conducted on cables fitted with internal instruments. Those studies that have been done have concentrated on cable behavior averaged over significant cable lengths. Researchers at the Spokane Research Laboratory (SRL) of the National Institute for Occupational Safety and Health in Spokane, WA, are investigating the physical properties of cable bolts by replacing the conventional king wire with a modified king wire on which strain gauges have been installed . This paper documents test results on these modified cable bolts. Three tests were conducted at SRL on 1.83-m-long cables grouted into two 0.91-m-long pull-tube assemblies. Load along the cable was monitored with 20 strain gauges installed along the length of the cable. The instrumented cable bolt provided reproducible point measurements of cable load as opposed to load measurements averaged over significant cable lengths. Such point measurements can assist in interpreting the influence of cable confinement, grout quality, rock mass stiffness, and other factors. The instrumented cable bolt is a practical field and research tool because it can predict point loading along the cable and thereby allow interpolation of maximum possible loads on a cable.

May 1, 2002

By G. Akdogan, I. J. Geldenhuys, Q. G. Reynolds

Efficient recovery of titanium from titaniferous magnetite ores continues to be a promising, yet unrealised opportunity, despite significant occurrences of titaniferous magnetite deposits worldwide and the existence of established industrial-scale practices. Current smelting processes only recover iron and vanadium, while the titanium is discarded in the waste slag. These slags are stockpiled and present massive environmental challenges, while still containing value as residual iron, vanadium and titanium. The complex mineralisation of these deposits does not allow for a significant opportunity to separate the titanium and magnetite minerals through normal physical upgrading processes. An upgrading process is therefore required to derive economic value. An efficient process technology could create an opportunity to unlock all three valuable commodities. South Africa’s Bushveld Complex, the largest known deposit of its kind in the world, is known for the high vanadium content but is also associated with relatively high concentrations of titaniferous magnetite. The quality of the Bushveld Complex was one of the drivers for the establishment of the Highveld Steel and Vanadium Company in the mid-1960s. The unfortunate demise of Highveld Steel and Vanadium created an opportunity to review current practices and evaluate the best available process for this complex ore in the context of the three elements of interest. Past and current processes, the nature of these deposits and the potential to recover titanium are assessed to highlight the potential of fluxless smelting of titaniferous magnetite to produce a titania-rich slag as feedstock to the pigment, titanium metal industry in conjunction with recovery of iron and vanadium. Ilmenite smelting practices are proposed as a suitable alternative to achieve the goal, namely sustainable processing. Keywords: Titaniferous magnetite, titanomagnetite, smelting, titania slags, comprehensive processing

Jan 1, 2020

By F Gervilla, J Laukkanen

The Kevitsa Ni-Cu-PGE deposit in northern Finland contains disseminated Ni-Cu-Fe sulfides, and platinum-group minerals (PGM). The 2.05 Ga-old ultramafic-mafic, funnel-shaped intrusion is intruded into a volcanosedimentary sequence. The major ore minerals are pentlandite, hexagonal pyrrhotite and troilite, chalcopyrite, cubanite and magnetite. Pyrrhotite and pentlandite are replaced by pyrite, millerite and heazelwoodite near the surface. Nickeline, maucherite and gersdorffite are locally abundant. A pilot feed sample of 575 t of the main orebody at Kevitsa had average grades 0.45 per cent Cu, 0.36 per cent Ni, 1.85 per cent S, 0.33 g/t Pt, 0.34 g/t Pd and 0.19 g/t Au, with 0.06 per cent Ni contained in silicates. Higher PGE contents (2 - 27 ppm) occur in a vertical N-S bearing fault zone. The PGM (n = 6022) mapped in specimens of four drill holes, consist of sperrylite 34.7 vol per cent, braggite and cooperite 18.5 vol per cent, geversite 17.2 vol per cent, moncheite 14.7 vol per cent, merenskyite 6.7 vol per cent, stibiopalladinite 4.3 vol per cent, sobolevskite 1.9 vol per cent, kotulskite 0.7 vol per cent, michenerite 0.6 vol per cent, keithconnite 0.3 vol per cent, rustenburgite 0.1 vol per cent, melonite, froodite, laurite together 0.1 vol per cent and only a few grains of sudburyite, irarsite, vysotskite, erlichmanite, hongishiite, Pt-Cu-alloys, three undefined Pd and Pt bismuthinides and antimonides and a Pd-Cu-bearing Pt-Ni-Fe sulfide. Most of the PGM, 62 per cent, are enclosed in silicates, 29 per cent are intergrown with sulfides, nine per cent are within sulfides. A portion of the PGE occurs in solid solution in sulfides and arsenides. Ni flotation yielded smelter-grade concentrates averaging 12.2 per cent nickel. The average sulfide Ni recovery is 78.8 per cent and total Ni recovery is 65.3 per cent. The average Pt is 10 g/t at 55 per cent recovery, Pd 7.7 g/t at 38 per cent recovery and Au 1.6 g/t at ten per cent recovery. Cu concentrates averaged 28.6 per cent Cu with an average recovery of 78 per cent and further 11 per cent in the nickel concentrate. The copper concentrate contains 4 g/t Au at 24 per cent recovery. The average Fe to MgO ratio 17.9 is well above the targeted minimum of 4.5. The pilot results show that the previously used TETA (triethylene tetramine) can be avoided and good quality, smelter-grade concentrates can be produced from the Kevitsa ore at economical levels of recovery by conventional flotation methods.

Jan 1, 2008

By Marvin J. Udy

THE preparation of this paper is in response to many requests for in-formation on the mining and smelting developments which have been carried on for the past three years or more by the Chromium Mining and Smelting Corporation of Canada. By way of introduction, the following paragraphs, relating to the early history and present status of the chrome-mining industry in the United States, are of interest. They are quoted from Bulletin No. 76 of the California State Mining Bureau, published in August, 1918: &apos;Chromium was discovered about 1797 by a French chemist, Louis Nicolaus Vauquelin, in ore from Siberia. From that time until 1827, the Urals, in the region of Ekaterinburg, supplied the chromium used in . Europe. In the summer of 1827, as the historian advises us, Isaac Tyson, Jr., saw in a Baltimore market-place a cart containing a cider barrel, which was held from rolling about by some heavy black stones. He had made a study of such stones at the first-known American locality, the Bare hills near his father&apos;s home, six miles from Baltimore, and he recognized the black stones as chromite. On inquiry, he found the chromite came from the Reed farm in Harford county, 27 miles northeast of Baltimore. At this time, Tyson was one of the very few men in the country who knew the value of chromite, and in the next few years he took full advantage of this knowledge. He immediately bought the Reed farm. He found about 30 tons of float-ore on the surface, but there was no outcrop of ore in place. Never-theless, he sank a shaft, and at a depth of eight feet struck an ore-pocket which proved to be 80 ft. long, 25 ft. wide, and 8 ft. in maximum thickness. His next discovery was of placer chromite in the sands in the beds of brooks on an estate called Soldiers&apos; Delight, 16 miles northwest of Baltimore. Thus far, Tyson&apos;s observations had shown him that chromite occurred apparently only in serpentine areas. His explorations were now leading him farther afield. In 1828, he found on the Wood Farm, in Lancaster county, Pennsylvania, a deposit of float chromite which led him to lease the ore-right of the farm, which he finally purChased in 1832. Here he developed the famous Wood mine, the largest single producer of chromite in the world.

Jan 1, 1938

In the plumbing of vertical shafts the methods employed and equipment used, are generally made to best suit existing conditions. Undoubtedly, there is no method that can be called standard or that can be used with equal ease and success on all shafts. At the Mount Isa Mines Limited property in Northern Queensland, Australia, local conditions have presented no major difficulties to be overcome in shaft plumbing work. In fact, compared to those at many shafts, the problem has been rather simple. There are three vertical shafts connecting main mine workings, with the greatest plumbing depth for any single lift, 350 ft.Other conditions pertaining to plumbing work have been generally normal.The method we have employed is, in principle, similar to the Weisbach orientation method with a variation that does not necessitate damping of the wires to bring them to rest. Although conditions encountered have not been such that damping the wires would have been inconvenient, we feel we have saved much time and eliminated unnecessary...

Jan 1, 1940

By Hugh W. Evans

Many reports and papers have been delivered on projects under construction or already in operation, but we believe there are few that have been written about projects yet to be built specifically dealing with advanced mine and environmental planning. This paper describes such planning for Atlantic Richfield Company&apos;s Black Thunder mine. Project planning is a cyclic phenomenom involving four broadly overlapping planning steps (Figure 1). The demands of the public include needs that can be satisfied through planned resource development. Using a base of information that partly exists and must in part be gathered and updated, the preplanned development can be, evaluated. The evaluation process, with built-in environmental constraints leads to an implementation procedure. Implementation results in the development, including the release of the affected area to other public demands that follow.

Jan 1, 1975

By D. F. Hambley

This manual contains a step-by-step procedure for the design of ore passes for open pit mines. The manual is comprehensive and deals with all aspects including location, design, construction and operating considerations. In the construction section, all applicable raising and shaft sinking methods are considered and cost estimates and advance rates provided for each. The design process is divided into several sections - rock flow requirements, support design, dump point design and draw point design. Use of this manual provides open pit planning engineers with a means of designing and assessing the feasibility of ore passes for their operations.

Jan 1, 1983

By G. H. Babcock, D. A. Knight, V. G. Medina

"Production commenced at the Golden Sunlight Mine in 1983 and at Kidston Gold Mine in 1985. These projects were both constructed under the management of the Placer Dome Inc. (Technical Services) group of Vancouver, B.C.Golden Sunlight uses a conventional rod mill/ball mill grinding circuit while Kidston uses a SAG /ball mill, and later on, SABC circuit. Since the hardness of the ore and the fineness of the primary grind in both mines are about the same, a meaningful cost comparison can be made. The comparison is made on the basis of capital and operating costs.The result of this study indicates that a significant capital cost savings can be achieved in favour of the SAG /ball mill circuit when the ore is amenable to semi-autogenous grinding. With a good maintenance program, the operating cost for the SAG /ball mill circuit could also be lower that the conventional rod mill/ball mill circuit.HISTORYGolden Sunlight MineGolden Sunlight is a 5 530 t/d gold mine located near Whitehall, a small town 60 km east of Butte, Montana. Originally optioned by PDI U.S. in 1958, the development of the property waited until 1981 when economic conditions became favorable for the project to proceed.Semiautogenous grinding tests were conducted during the final stages of the feasibility study. The hard near surface ore was not quite amenable to semi-autogenous grinding. The best result produced from a series of tests using a 1.83 m diameter mill was a semiautogenous work index of 39. This is substantially higher than the 22 Bond work index of the sample used in the testwork. A conventional SAG/ball mill circuit for this ore will be extremely inefficient, and for this reason, this circuit was rejected in favour of a conventional rod mill/ball mill circuit."

Jan 1, 1991

By Russell G. Warncke

"This report is based primarily on a study of safety conditions and practices followed in the coal mines of Japan. Not all of the coal fields in Japan were studied, but typical mines in the largest producing areas and a fair cross section of coal-mine-safety conditions observed during February to April 1948 are described.Information was obtained through investigations conducted in the mines, discussions with mine-management officials and representatives of labor unions of the various mines visited, and examination of records and statistics from the various offices of the Coal Board of the Ministry of Commerce and Industry and from the Coal Association of Japan. Statistical data covering the same subject, obtained from different sources, varied in many respects and apparently were reported inaccurately, but such discrepancies can be attributed to different methods of reporting and compiling statistics.It is difficult to correlate the high fatal and nonfatal injury rates that prevail in Japanese coal mines with the conditions observed in the mines. Virtually all mines visited were attempting to prevent accidents and explosions, by apparently following known safety precautions for the prevention thereof. Some commendable safety innovations were observed at several mines; they indicated that mine officials are giving thought and consideration to hazardous conditions that affect their particular mines.Naturally, the operating officials and management were anxious to impress the writer with their interest in accident prevention and safety. Operating officials were found to be receptive to safety and wore interested in formulating definite safety programs. Some nines had well-planned and well-organized safety programs, which, if put into effect, would contribute greatly toward reduction of accidents.The approach to safety in Japan is quite different from that in the United States, especially the concept of personal responsibility for accidents and the extent to which the individual should be protected against hazards. Management is responsible for providing and maintaining safe working conditions. Collaboration between management and worker, as understood in the United States, does not exist in Japan.Increase in accidents since the cessation of hostilities is the result of unsettled economic conditions in the coal industry, influx of inexperience workers, and breakdown of discipline among the miners, who have been organized into unions. Those unions are greatly influenced by ""leftist"" tendencies.It was observed that the Japanese mine worker is fatalistic by nature and has little, if any, noticable safety consciousness. The most urgent major requirements to reduce accidents in the coal mines are to train the worker in accident prevention and instruct him regarding the inherent hazards of his occupation.Revision of the mining laws would help to reduce accidents if the companies would comply with such laws and provide safer working places and if the workers would cooperate with management and observe and comply with such laws as are enacted for their protection."

Dec 1, 1949

By D. Jepsen

Land access and tenure certainty for exploration and mine development is absolutely critical to the foundation of a healthy, sustainable and environmentally-sound mineral exploration and mining sector. Without certainty, mineral exploration will be severely eroded, resulting in reduced possibility of discovering and developing new mines. The development of positive relationships based on a shared commitment of understanding, mutual respect and trust by First Nations and the mineral sector can provide this increased business certainty and social and economic benefits for local First Nations. As a sector, we face many challenges in regard to building relationships with First Nations. The root solution to addressing these challenges lies in recognizing and understanding the unique cultural differences that exist between indigenous people and the business community. From the Canadian perspective, the First Nations culture differs vastly from non-Aboriginal culture. It is equally as imperative that cultural differences be acknowledged and respected at home as they are when seeking business opportunities in other countries. The traditional “business” approaches and relationships that one understands and incorporates with one’s contractors, legal counsel, investors and Board are generally not be the best approach for the introductory and subsequent meetings with indigenous peoples. This paper is written from the perspective of my experiences accumulated over the past ten years, first as Manager of Aboriginal Affairs for one of the largest forest companies in British Columbia and now, as President and CEO of the Association for Mineral Exploration BC (AME BC). My opinions are not necessarily endorsed by AME BC. Before the gritty issues of consultation and benefit sharing are dealt with, it is worthwhile to clear up the confusion surrounding terminology. “Indigenous Peoples” is used in a global context; “Aboriginal Peoples” is used in the Canadian context therefore includes Métis, Inuit and First Nations Peoples. The term “First Nations”, in the context of British Columbia, perhaps has its roots in the fact that treaties have largely not been settled. Therefore it is important to reaffirm that British Columbia was not discovered. First Nations have resided in British Columbia since time immemorial.

Jan 1, 2007