Search Documents

In choosing such a threadbare subject for a paper I fear that I may in some measure be taxing your patience, yet as upon the accuracy with which the work is done depends the result of conclusions drawn as to whether a property will be profitable to work or otherwise. The subject cannot be too well threshed out, and I trust that upon certain points that have come within my own experience I may be able to give 'hints that will prevent others from making mistakes. First as to alluvial. Gold is often found from the grass roots down, often ill particular horizontal bands in the wash, but more generally concentrated either on a true or false bottom. When sampling dry ground for proposed hydraulicing I have obtained accurate results only by taking the whole of the dirt from measured shafts, stacking it as it was lifted on a tarpaulin, and putting the whole quantity through a carefully constructed box. In wet ground careful borings will in most cases give fairly correct results, but where it is possible to sink shafts, that should be done, as a guide is then also obtained as to the nature of the wash, whether it is bouldery, cemented, or free. Sampling in a face is a more difficult work in many respects than in new ground, as so many elements enter into action to spoil accurate sampling. Of course the great thing to avoid is sampling in any place where either natural or artificial concentration has taken place, and very much has to be left to circumstance and the sampler's own judgment. In passing I may mention that I have on several occasions seen diggers deceive themselves in wet ground where they were sinking and coping as best they might with water. They would take a dish of dirt from the bottom of their hole, pan it off, and take the result as a fair yield, and on the strength of it perhaps spend a lot of time and money in tail races and whereas in their sample there had been a process of concentration carried on, the movement and working in the water had caused the gold to work down, and anything like accurate estimations by the method pursued were out of the question.

By Ke Yang

Drilled shafts are widely used as foundation system for sound walls to resist lateral loads. The design method based on the ultimate lateral capacity, such as Broms method, is often used for sound wall foundation design. Allowable Stress Design (ASD) is currently used for deep foundation design. However, by October 2007, all states Department of Transportations are required to use the Load Resistance Factor Design (LRFD) approach for the design of foundation in highway projects. There is a need to develop a calibrated resistance factor in LRFD lateral design of drilled shafts supporting sound barrier walls. This paper provides resistance factors for design of laterally loaded drilled shafts supporting sound walls using Broms method based on the study using reliability based method and fitting to ASD method. Additionally, the resistance factors for static lateral load tests are recommended. Furthermore, a methodology to update the resistance factors using Bayesian approach by incorporating the on-site full-scale lateral load test results is presented. To illustrate the Bayesian update methodology, two lateral load tests in Colorado were employed to develop the updated resistance factors.

Jan 1, 2007

By J. Bongardt

Ecologically acceptable techniques are described for the handling of waste materials from the fabrication industry. New production methods and the recycling of sludges from grinding and other waste materials are suggested.

Jan 1, 1997

By P Cotton, N Cox

The Brisbane City Council has implemented a program of continual improvement at its Mount Coottha Quarry in the heart of Brisbane, Australia. The program has been underway for the past 6 years, and has resulted in very significant improvements in terms of both the cost effectiveness of its operation, and in terms of its environmental impact on nearby residents. The work has included a focus, amongst other things, on blasting efficiency and has challenged conventional thinking in terms of the size of blasts fired, the frequency of firing, the diameter of blastholes, and the use of bulk emulsion or slurry explosives.

Jan 1, 1996

By P. Goosen, A. Paterson, E. Paulsen

Ticor South Africa is currently involved in the mining and processing of a heavy mineral oredeposit at Hillendale Mine on the KwaZulu-Natal north coast. The orebody is characterized by a high ultra fine fraction (-45µm) that has a variable rheological behaviour when subjected to shear and hydration. Experience at Hillendale has shown that the ultra fine mineral tailings are sensitive to shear history in terms of shear intensity and shear duration as well as hydration history. This phenomenon expresses itself right through the primary beneficiation process influencing the mineral separation, but is especially prevalent on the residue disposal i.e. slurry transport and deposition on the tailings impoundment. Tube viscometer test work was conducted on the flocculated fine tailings that indicated that there was a change in rheology as a result of shear. This paper presents the results of the on-site test work conducted at the mine to measure the rheology at various stages in the process.

Jan 1, 2003

By W. H. Ode

In 1949 the Coal Committee of the Economic Commission for Europe, Geneva, Switzerland, established a Classification Working Party, to develop an international system for classifying coal. This project was necessitated by the increased trade in coal among various nations following World War II. Although national classification systems existed, they had been developed to cover the characteristics of domestic coals without reference to coals of other countries. Different terms for describing similar or identical coals in each nation caused confusion in evaluating coals shipped in international trade. Experts from Austria, Belgium, Bulgaria, Czechoslovakia, Denmark, the Federal Republic of Germany, France, Greece, Hungary, Italy, the Netherlands, Poland, Sweden, the Union of Soviet Socialist Republics, East Germany, the United Kingdom, the United States of America, and Yugoslavia participated in various stages of the classification work. Walter A. Selvig was appointed by the Bureau of Mines as the technical expert to represent the United States because of his experience in developing and standardizing methods of analyzing and classifying American coals. He served on the Classification Working Party until his retirement from the Bureau of Mines early in 1956. Extensive laboratory work was done in connection with the classification studies at the Pittsburgh Experiment Station of the Bureau of Mines.

Jan 1, 1958

By Josef K. Alter

Crosshole Sonic Logging (CSL) of drilled shafts requires 1.5-in (38-mm) or 2-in (51-mm) I.D. sonic access tubes to be installed inside the steel reinforcement cage. The sonic access tubes do not contribute to the structural capacity of the drilled shaft. The proposed use of Ischebeck TITAN T73/56 CSL/Hollow Threaded Rebar for Cross Hole Sonic Logging Access Tubes Combined with Longitudinal Concrete Reinforcing in Drilled Shafts (patent pending) is discussed as an alternative method of construction and CSL probe access. The T73/56 hollow threaded rebar/sonic access tube performs as a high strength rebar while at the same time creating a 2.2-in (56-mm) I.D. sonic access tube. The deformed high strength hollow bar provides better adhesion to concrete thus reducing the problem of debonding associated with smooth PVC and steel pipe. A cost comparison using conventional rebar with added sonic access tubes is discussed. The use of T73/56 CSL/Hollow Threaded Rebar as a value engineering alternative can reduce both material and labor costs for drilled shaft construction and can provide an advantage where anchor bolt cages and longitudinal reinforcing create congestion.

Jan 1, 2011

By Cathleen J. Webb, Arden D. Davis

The Homestake Gold Mine at Lead, South Dakota, has been proposed as the host site for the Deep Underground Science and Engineering Laboratory. The laboratory will house neutrino experiments in mine workings at the 7400-foot depth, as well as research in geomicrobiology, rock mechanics, and ground-water flow. Initial plans for the laboratory were developed in 2000 after Homestake Mining Company announced the closing of the underground gold mine. Homestake’s owner, Barrick Gold Corporation, had agreed to donate the mine for a laboratory if it could be protected from environmental liability. That initial agreement was delayed, and Barrick turned off the mine’s pumps in 2003, allowing lower levels of workings to begin to flood with water. In early 2004, the Governor of South Dakota signed an agreement with Barrick that would indemnify the company and eventually transfer ownership of the mine to a state laboratory authority. South Dakota’s governor also announced plans to ask the state legislature for funds to help in the initial construction of the laboratory. A consortium of scientists from several states is currently preparing a detailed laboratory proposal for the National Science Foundation.

Jan 1, 2005

By Qingsheng Liu

A new method of recycling aluminum dross for preparation Al-Si-Ti alloy was studied in this paper. This was carried out in two processes. first the aluminum doss was pretreated by leaching and calcining process, the fine purity and phase of the intermediate oxide powder up to electrolysis demands, then, could be obtained when aluminum dross after washing have been leached for 2h at 100? in 20% hydrochloric acid and calcined for 2h at 1200?, which was treated by cryoite-based molten salt electrolysis. Finally, the Al-Si-Ti alloy was successfully obtained through electrochemical co-deposition in the cathode shows a typical as-cast microstructure. This new recycling method can produce high quality alloy and may bring remarkable economic and social benefits.

Jan 1, 2010

Like it or not, CPD is upon us. As from 1 January 2006, all registered engineering professionals, i.e. professional engineers, professional engineering technologists, professional certificated engineers and professional engineering technicians, were required to undertake CPD in order to keep their professional registration current. The rules regarding CPD have been gazetted under Government Gazette No. 28328, Board Notice 131 on 23 December 2005, and they also appear on the ECSA website?www.ecsa.co.za. For the convenience of our members they are reproduced in full in this issue of the SAIMM Journal.

Jan 1, 2006

By B. J. du Plessis

Automation of the conventional grinding circuits of Palabora Mining Company (PMC) required that adequate instrumentation and a control system had to be put in place, after which extensive testing had to be done to evaluate different grinding control strategies. The objective was either to optimize the particle size from the grinding circuit, or to increase milling circuit throughput while maintaining particle size at existing levels. Prior to automation of the process as described below the circuits were controlled manually. No on-line information on cyclone feed densities, cyclone feed flow or cyclone overflow particle size was available. This type of control relied heavily on interpretation of the process parameters by the operator and on his ability to make informed decisions on what the set points should be. An integral component of the automation process was the installation of a SCADA package (SysCad SDX) for implementing the on-line control strategy. A self-correcting model for prediction of cyclone particle size was developed and implemented on the SDX. The model is calibrated using values from the particle size analysers while they are operational. If the particle size analysers choke or fail for any reason, the model continues to provide a good estimate of the particle size. This technique ensures that a continuous particle size indication is available compared to the intermittent reading from the instrument. The continuous signal allows particle size to be used as a process variable for control purposes. A strategy was developed and implemented which allows for the production of a controlled grind size from the conventional milling circuit to the flotation circuit. The grinding control strategy allows for the control of particle size from the individual cyclone overflows. This strategy allows the operator of the process to increase or decrease production rate by specifying a coarser or finer grind size required for flotation.

Jan 1, 2001

By L. Nell

Bateman, like other engineering contractors, carries out or participates in many studies of potential projects in the Minerals Industry. This paper aims to explain the contracting approach to feasibility studies as practiced by Bateman, particularly where this differs from a traditional mining company approach. A brief description is provided of the usual phases of a project and the types of estimate needed to proceed from one phase to the next. Possible organizational structures involving different forms of association between owner, contractor and consultants are then outlined. The bulk of the paper then demonstrates that the cost estimates prepared stem directly from the mining plan, metallurgical process design and engineering design philosophy. The steps to be followed in order to prepare a credible estimate which accurately reflects the design constraints are described. The importance and the methodology of carrying out value engineering and of preparing contingency estimates based on a thorough risk analysis exercise are then discussed. Financial modelling techniques are described briefly. The paper concludes with short summary case studies of two recent investigations of potential projects in Africa.

Jan 1, 1999

As part of the United States Department of the Interior, Bureau of Mines Health and Safety Research Program, Walter C. McCrone Associates, Incorporated has examined 71 samples of airborne mine dusts using the techniques of x-ray diffraction, electron microprobe analysis and light microscopy. This report details the procedures which were used in this work and documents the results which were obtained.

Jan 1, 2011

By D Craw

The Rise and Shine Shear Zone is a mineralised low angle deformation zone traceable for at least 7 km through biotite zone schist of the Dunstan Range, central Otago. Rocks from the shear zone obtained from recent drillholes are unweathered and facilitate paragenetic studies. There is a progression of mineral deposition from semiductile foliation-parallel shearing, to subsequent folding, and brittle fracturing. Sheared rocks are dominated by microshears containing fine grained hydrothermal muscovite and rutile that has recrystallised from metamorphic muscovite and titanite respectively. Euhedral pyrite occurs within segregations in the schist and is locally brecciated by the shears.   Arsenopyrite occurs within microshears and is intergrown with hyrothermal muscovite. Fractures within relatively undeformed schist are filled with ankerite, siderite, chalcopyrite, sphalerite and galena and these veinlets also crosscut the microshears. Locally the schist is folded and zones of brecciation, silicification and vein deposition overprint the rock. Vein quartz and albite predominate and arsenopyrite and gold infill breccia matrix and crosscutting veinlets. Sulphide deposition began in the later stages of metamorphism with pyrite deposited in quartz-albite segregations. Subsequent shearing caused brecciation of some grains and accompanied deposition of arsenopyrite ¦ gold and rare sulphides along foliation-parallel microshears. Minor amounts of chalcopyrite, sphalerite and galena were then remobilised in ankerite veins that crosscut the shears. In areas of high strain, arsenopyrite was then deposited as euhedral grains in veins and breccias. Synmineralisation deformation caused the brecciation of some grains and gold was deposited infilling fractures in the arsenopyrite. The paragenetic sequence shows gold mineralisation occurred in two distinct sets of structures (semiductile and brittle) that formed at different times in the formation of the shear zone.

Jan 1, 2006

By Anthony Leddin, Gillian Dooley

This paper is concerned with mineral policy in Ireland and how it might be improved to encourage more exploration and investment in mining in the country. The approach is to first outline the main desirable characteristics of a comprehensive national mineral policy document. This aspirational document is then used to assess the current regulatory, legislative and fiscal frameworks for mining in Ireland. The analysis also contains a brief account of the history, structure and characteristics of the mining industry in Ireland. The main focus of the paper is to identify those aspects of the existing framework that erode Ireland’s attractiveness to mineral investment and to suggest policy improvements.

Jan 1, 2005

By S. J. Swart

This paper discusses the principles and application of risk assessment and management as the basis for environmental management within the mining industry. Unlike in other industries, mines are required to obtain closure certificates in terms of section12 of the Minerals Act, which should ultimately release them from further environmental responsibilities. It is emphasized that the concept of environmental risk assessment and management, when applied correctly will mean that the mine will be identifying and managing environmental issues beyond those set by current legal requirements and management strategies. The focus shifts from conventional minimum legal compliance management to management of real environmental risks. The advantage of this approach is that the perceived ?shifting of legal and management goal posts? due to changing environmental laws or management principles, will not influence or dictate the mine?s short or long-term management objectives or actions, mine closure funds can be more accurately determined and mine closure should become a relatively simple procedure. The risk assessment approach has been applied to the planning of mine closure at Iscor?s Durban Navigation Collieries (Durnacol) in Kwa-Zulu Natal and certain key risk issues such as the long-term risk of water pollution from coal discard dumps have already progressed to fully quantitative risk assessment. This paper will discuss the process, which has been followed to date, with particular emphasis on the most recent phase, namely quantitative risk assessment and management of pollution from coal discard dumps. It is believed that the approach that is being pioneered at Durnacol and which overcomes some of the more obvious deficiencies of both the EMPR and the traditional IEM process will ultimately serve as the model for all responsible mines in South Africa. It is also believed that this approach will enable the authorities to issue closure certificates with the confidence that there will be no unforeseen surprises in the years after closure.

Jan 1, 1998

By D. A. Reynolds

A few studies on the relationship of the fusion temperature of the ash on coke to that of the corresponding coal have been made on commercial high-temperature cokes. H. J. Rose3/ in 1921 compared the fusion temperatures of the ashes of 10 coals and the cokes produced from them and concluded that they were in such hose agreement that either figure could be used. More recently, Quarfort4/ found that the ash of coke fused at a somewhat lower temperature than that of the original coal. As the ash of a coal and that off tie coke produced therefrom have the same origin their chemical composition should be identical, provided that carbonization has not altered the inorganic, or ash-forming, constituents of the coal, and such alteration seems highly improbable. However, it has been shown5/ that coke is liable to contamination by iron during crushing and grinding preparatory to sampling. Pieters6/ found that coke ash was contaminated in this manner up to 0.4 percent. Extraneous iron would lower the ash-fusion temperature because such iron may form ferrous silicate, which is readily fusible.7/ These results provide a basis for the prediction that the ash of coke will fuse at a lower temperature than that of the corresponding coal, especially if the fine grinding of the coke was done by rubbing -surfaces of iron, as in a disk pulverizer or bucking plate.

Jan 1, 1940

By C Placzek, E Beattie, K Blake

Channel iron deposits (CID) consist of ferruginous chemical sediments, and are an unusual subset of Phanerozoic ooidal ironstone deposits almost unique to the Pilbara, where they constitute around 19 per cent of the Pilbara’s iron ore exports. These deposits occupy many of the ancestral river channels of the Pilbara region, especially the Robe River palaeochannels, incising and meandering through the Precambrian banded iron formations (BIF) of the Hamersley Group and the underlying Fortescue Volcanics.This paper explores the factors underlying geochemical variation in CID, particularly the chemical properties of goethite. The selected deposits in the western Robe palaeochannel and its tributaries show little or no secondary reworking by later water tables. There is a total absence of aluminosilicate clays with all the deleterious elements such as aluminium and silica. Instead, these are associated with the goethite mineral lattice, either within or adsorbed to the cortices of pelletoids.A thickly vegetated environment, and the presence of the Maddina Volcanics as potential source rocks for these western Robe CID is offered as an explanation for relatively high aluminium in the deposits studied, and, in turn, as the reason most parts of the palaeochannel are preserved as inverted topography.CITATION:Beattie, E, Placzek, C and Blake, K, 2017. Dirty goethite – a geochemical characterisation of some western Robe River channel iron deposits, in Proceedings Iron Ore 2017, pp 489–502 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By Michael Peterson, Robert Davinroy, Robert Rapp, Gregory Hempen, David Herzog, Thomas Keevin

Fish sampling in a deep-water, high velocity, environment is extremely difficult. Conventional techniques such as electro-fishing and netting have been limited to depths generally less than 7 meters (m) and velocities below 1 meter per second (mps). The goal of our study was to sample a bendway weir field on the Mississippi River to assess the effects of the weir field on the fishery. In a bendway weir field, depths can exceed 20 m, and velocities can exceed 3 mps, making conventional sampling techniques inefficient.

Jan 1, 2002

By Wilford S. Wright, Harold E. Heide, Robert S. Sanford

"INTRODUCTION The United States production of tin has always been negligible, and domestic requirements have been met almost entirely by imports. The advent of war in Europe in 1939 brought a threat to our foreign source of supply, and steps were taken by Congress to forestall shortages of tin and other metals. By authority of the Strategic Minerals Act, passed by Congress in 1939, the Bureau of Mines and Geological Survey conducted investigations of domestic tin deposits.An examination of Alaska deposits was undertaken in 1940 and 1941 by J. B. Mertie, Jr., and Robert R. Coats of the Geological Survey.H. B. Heide conducted a preliminary examination of lode and placer-tin deposits at Cape Mountain in 1942, which was followed in 1943 and 1944 by a program of exploration by churn drilling in the placer area and trenching and sampling the lode deposits.Placer tin, found at the head of Goodwin Gulch, Cape Creek, First Chance Creek, and Boulder Creek, indicates that the mineral was derived from the vicinity of lode cassiterite occurrences on Cape Mountain. Placer tin led to the discovery of at least one, cassiterite vein by the Geological Survey and the Bureau of Mines."

Dec 1, 1946