Search Documents

By B. M. Nyombolo

Mintek has been involved in the development of bioleach technology for many years, initially for refractory gold extraction, and more recently also for base metals extraction. Mintek, in collaboration with its Australian technology partner (BacTech), is the technology provider for the Beaconsfield refractory gold bioleach plant. At present Mintek, BacTech and Peñoles are constructing a demonstration bioleach plant for copper-zinc concentrate treatment. Bioleach liquors produced in all applications have to be neutralized. In the copper-zinc case, neutralization is required for bleeding iron from the circuit and for adjusting the pH value ahead of solvent extraction. In the refractory gold bioleach circuit, neutralization is required for producing a stable iron-arsenic residue. Some of the challenges encountered in each of these neutralization applications are discussed, and examples of results obtained are presented.

Jan 1, 2000

"At a current mining rate of 3,750 tons per day, La Mine Doyon is currently the largest gold mine in Canada. La Mine Doyon is an open pit gold mine located in the Abitibi area of Northwestern Quebec. The project is a joint venture between Soquem, a Quebec Crown Corporation in the resource development field and Lac Minerals Ltd., a publicly-held, resource development company. Lac Minerals is the managing company and operator of the project.Doyon went into production in 1980 on a very limited basis at 600 tons/day, and has seen a step wise increase to the current rate of 3,750 tons/day. Initially, all the ore was processed at Noranda Mines, Horne Division as flux for the copper smelter. The East Malartic Mill in Malartic was then upgraded and began processing Doyon ore. The third step in the progressive increase of throughput was the commissioning of the Doyon mill in November of 1982. Doyon ore is currently being processed at all three locations.During 1983, an exploration ramp was driven to explore the ore below the ultimate pit depth. Current plans indicate the sinking of a shaft and the commencement of underground mining during the next 2 or 3 years.Since its humble beginning, La Mine Doyon has always been a success; ore reserves have been extended to the east and the west and will soon be confirmed at depth, the mining and processing rates have been increased 6 fold, and the recovery has been increased from a designed recovery of 85% to over 95%. The intent of this paper is to trace the history and reasons for these rather dramatic improvements."

Jan 1, 1984

The State of Washington has a federal program that gives the Office of Surface Mining responsibility for assuring the reclamation of lands affected by coal mining. Most of Washington's coal-bearing regions lie west of the Cascade Mountains. The state's coal reserves are estimated at 1.4 billion tons, about 0.3 percent of the nation's total coal reserve. Steeply dipping. minable seams range from 2.5 to 25 feet in thickness. The occurrence of coal in Washington has been documented since the early days of its settlement; at one time, coal production played a significant role in the state's economy. During the late 1800s and early 1900s, coal was second only to lumber in Washington's industrial production. Coal production declined as other sources of energy were developed. By 1959, production was at 200,000 tons. Regulation of the coal mine operations in Washington is conducted by the Office of Surface Mining's Casper, Wyoming, Field Office and its local office in Olympia, Washington. All permit applications and abandoned mine land reclamation are completed by the OSM Western Support Center in Denver, Colorado. Inspections of mine and reclamation sites are conducted by OSM reclamation specialists located in Olympia.

Jan 1, 1992

By K. Shoji

Residence time distributions (RTDs) were estimated by water tracing in a number of wet overflow ball mills (diameters 0.38 to 4.65 m) producing dense, coal-water slurries. In open-circuit mills of 0.38 m diameter and various length-diameter (L/D) ratios, the mean residence times of solid were also determined from measured mill holdups. Holdup increased with increased mill feed rate, but the mean residence times of coal and water were still equal to each other. The experimental residence time distributions were fitted to the Mori-Jimbo-Yamazaki semi-infinite, axial mixing model, and the dimensionless mixing coefficient was determined for each of 25 tests in single- and two-compartment mills. This coefficient was found to be independent of the feed rate but linearly proportional to the D/L ratio. The mixing coefficient was smaller for two-compartment mills than for single-compartment mills, showing that there was reduced mixing introduced by the diaphragm separating the compartments. Equations are given to scale residence time distributions for changes in mill diameter and length.

Jan 1, 2008

By W. A. Dunkley, W. W. Odell

About two-thirds of the manufactured gas supplied to the public by the gas plants in the Illinois district is cnrbureted water gas. The leading generator fuel is coke, ma.de in by-product c.oke ovens or in retorts, chiefly from eastern gas coals. During the fall and winter of 1917-18, when the demand for coke by war industries and the restrictions of the Fuel Administration in connection with the transportation of coke from eastern States made it almost impossible for many gas companies to obtain their coke requireml'nts, several water-gas plants had to use bituminous coal as generator fud. Many operating difficulties were encountered, some of which were solved more or less satisfactorily in different plants. A number of plants attacked the problem rather blindly because facilities for making tests were lacking and because technical men were too busy with labor and supply problems to study thoroughly the conditions involved or to ascertain what other plants had done with this fuel. It was therefore with the hope of assisting the gas industry during this critical period, and of promoting the use of Central District coals for gas making, that the Illinois Mining Investigations, a joint agency of the U. S. Bureau of Mines, the University of Illinois, and the Illinois Geological Survey Division undertook the, tests discussed in this paper. • This report was compiled under the auspices of a technical committee appointed by Gov. Frank 0. Lowden to promote the use of Central District coals in gas manufacture as a war measure. This committee included the following representatives of the various agencies concerned: U. S. Bureau of Mines, E. A. Holbrook and W. W. Odell; Illinois Gas Association, C. W. Bradley and R. B. Harper; University of Illinois, Dean C. R. Richards, Prof. S. W. Parr, and Prof. H. H. Stoek; State Geological Survey Division, F. W. De Wolf, G. H. Cady, a.nd W. A. Dunkley. F. W. De Wolf was chairxnan of the committee and E. A. Holbrook was secretary.

Jan 1, 1924

By Ivan E. Goodner, Charles H. Fulton

THE subject of the constitution of copper-iron mattes has received considerable attention in recent years by Keller,1 Bolles,2 Hofman,3 and Gibb and Philp.4 Still more recently Friedrich, Röntgen, Wiedmann, Heyn and Bauer, and Leroux have published, in some instances, elaborate researches on the various systems of the sulphides, and the sulphides and their respective metals, which enter into the constitution of mattes, and have added very greatly to the knowledge of the subject. The work of Friedrich has been especially fruitful. But to date no effort has been made to correlate the data obtained in the latter researches and apply then to the study of the product called " matte," which is made in such large quantities by copper and lead-smelters. In this paper we propose to determine, by metallographic and chemical means, the constitution of copper-iron and copper-lead mattes in the light of the recent data above mentioned. We do not discuss copper-nickel mattes or speisses (artificial arsenides). The paper is divided into three sections I. A review and discussion of the various binary systems of the metallic, sulphides, and the binary systems of various metals and their respective sulphides entering into the constitution of mattes; also a discussion of the physical and chemical properties of these sulphides. II. A description of the results obtained from the chemical and metallographic examinations of the samples of copper-iron and copper-lead-iron matte obtained from various plants.

Nov 1, 1908

By Michael Drozd

"The operation of an activated charcoal system has five separate unit operations. These unit operations have common points for CIP, CIL and CIS system, which vary widely in application.The unit operations are:a. Absorptionb. Desorption (Stripping)c. Acid Washingd. Reactivatione. Carbon Handling (carbon transportation, sizing, dewatering, etc.)Cost optimization starts with the basic operating parameters (design philosophy) set down at the time of engineering design. These parameters undergo almost immediate change due to site specific ore requirements, throughput changes, operator requirements or reagent availability.Activated charcoal is sometimes viewed as simple, uncomplicated reagent that requires not optimization. To some extent, this statement is true, but under most circumstances, if the time necessary to optimize the use of activated charcoal is available, the effort is rewarded with significant savings. CPL-Carbon Link has embarked upon a program of supplying technical support with its activated charcoal. Several operations in the United States have undertaken to have CPL-Carbon Link do an operational survey to determine if potential savings are possible. CPL-Carbon Link has offered to do these surveys for projects that are clients or simply would like to have CPL-Carbon Link review their operation. The information accumulated by CPLCarbon Link is being used to attempt to fashion industry standards so that a common reference point can be established for activated charcoal usage."

Jan 1, 2008

By Roger A. Dworak

This report describes in detail the work done on the development of the Time Domain Reflectometry Microcomputer (TDRM). Modifications to the FMC-Model 302A Cable Fault Locator is described in Appendix D. The TDRM unit uses an 8080 microcomputer to accurately locate major faults in low capacitance cables to within ± 1 foot when properly calibrated. Major faults in high capacitance cables are usually located within ± 5 feet. The upper limits of fault detection are <1 kilohm shunt fault and >7 ohm series fault. In practice fault detection limits are reduced to <300 ohms shunt fault and >30 ohms series fault because of discontinuities caused by cable repair.

Jan 1, 1977

By R. Banda

This paper describes the decision to implement and then the implementation itself, through trials, of electronic ?Smartdets? over previously used shock tubes. It concludes that Mufulira Mine has become the first mine in Zambia to convert 100% of its stoping to ?Smartdets?, because the Mine?s management was prepared to look beyond the unit cost of product and were ready to look at the broader picture of cost effectiveness and increased productivity.

Jan 1, 2005

From time to time failures occur in structures made of lead, and the failure may be due to corrosion involving a definite thinning of the lead sheet, or it may be of such a nature that cracks develop and the lead appears to disintegrate. The idea of lead cracking will at once suggest something abnormal, for common experience shows that this metal is very ductile and will withstand considerable bending without showing any sign of fracture. Cracking, on the other hand, is usually associated with brittleness.Fig. 1 is a natural-size photograph of a cracked sheet of lead. Prior to photographing, the sheet was etched byimmersion in a solution of ammonium molybdate. Several characteristics of this crack will be evident. First of all it is distinctly a zigzag crack, and secondly it passes between, rather than through, certain well-defined areas which appear bright in the photograph. This is particularly noticeable at the lower end where the crack appears to terminate.

Jan 1, 1932

By Detlef Ehlert

With the proven “Plug &amp; Work” concept developed by SMS Siemag, automation systems are tested and optimized in the test field in a near-reality environment before being shipped and commissioned at a customer’s site. The process and production simulations provide scenes showing the specific mechanical equipment, the drive systems and the technology of the corresponding customer plant. Beside the technological simulation of the plant and the IO-simulation with the automation system, the production simulation is one of the three important parts of the Plug &amp; Work simulation environment. It serves two important additional purposes: the 3D visualization of the entire customer plant on the one hand and the mapping of the logistic procedures in the plant on the other. In order to provide a close-to-reality visualization of the plant, the original design data of the individual customer plant are used for creating the visualization and prepared using an appropriate export filter. In this way, it is ensured that production sequences can be optimized in advance together with the customer, so that each customer can be trained on his own future plant.

Aug 16, 2017

By Richard A. Walker

This report describes the development and performance of a multi-level, multi-function Calibration Light Source designed for field-calibration of a group of specific photometers. The Calibration Source is capable of providing ±35% accuracy calibrations at all of the following levels: 0. 05 foot-Lamberts, 6 foot-Lamberts, 6 foot-candles and 20 foot-candles. The Source was found to provide constant light output to within 1% over 50 hours of lamp operation and for line voltage variations of ±25%. It is compact and light-weight (11 pounds), and can be easily transported and used by one man in normal office environments (without requiring a darkroom).

Jan 1, 1976

By V. Osterholt

Sustainable development of mineral resources is based on a spatial model of the orebody that is only partly known from exploration drilling and associated geological interpretations. As a result, orebody models generated from the available information are uncertain and require the use of stochastic conditional simulation technique. This paper considers three methods for simulating orebody geology: (1) pluri-Gaussian simulation that limits the allowable contacts between the various units; (2) sequential indicator simulation using indicator kriging; and (3) an experimental multiple-point approach that captures some higher-order spatial statistics. The data requirements of the methods, how to meet them in mining applications, and performance characteristics are discussed. The application of these methods in a hypothetical deposit consisting of three geological units provides a comparison and illustrates the advantages of the different simulation approaches.

Jan 1, 2005

Council for 1999/2000 President M.H. Rogers President Elect Dr L.A. Cramer Vice Presidents Senior A.A.B. Douglas Junior S.J. Ramokgopa Immediate Past President J.R. Dixon Honorary Treasurer J.A. Cruise [ ] Annual report In accordance with the current management policy, this report on the activities of the Institute is presented under eight main headings: 1. Interests of Individual Members 2. Technical Meetings 3. Publications 4. Regional Development 5. Engineering Science and Technology in South Africa 6. International Liaison 7. State Liaison 8. Management and Administration.

Jan 1, 2001

By R. A. Halatchev

A risk model for assessment of the uncertainty in the forecasts of the planned profit is developed. It is based on the selling price of the metal recovered from the ore and the production per shift of the excavators. These two critical variables characterise the economic and technical aspects of the mining venture. Time-series methodology is used to describe the behaviour of the economic variable, which improves the adequacy of the modelling. A hypothetical open-pit gold mine is used to illustrate the application of the model. Results obtained show that the model is a good alternative to sensitivity analysis in taking account of the stochastic character of the price of the metal recovered from the excavated ore and the production per shift of the excavators used. The model can be extended by the inclusion of new variables that have a probabilistic nature

Dec 1, 1996

By Kay E. Goldberg

The Bureau of Mines conducted a study to develop and evaluate a training workshop for mine safety training personnel. The workshop was based on the Instructional Development Institute (IDI) which has been used for nearly ten years to train educators and administrators in the application of a nine-step model for defining, developing, and evaluating instruction. The Mining Instructional Development Institute (MIDI) was developed by investigators at the University of Southern California as a two-phase project. Phase I involved the modification of the six-day IDI program (including audiovisual presentations, workbooks, games, and exercises) for use by mine safety trainers as a workshop lasting three and one-half days. Phase II involved the evaluation and validation of the prototype MIDI workshop by means of a two-stage jury of experts and a prototype field trial. On the basis of data collected in the validation process it was determined that the institute provided an effective and useful method of instruction in mine safety training and that the institute would be especially valuable for mine safety training administrators and supervisors.

Jan 1, 1980

By D. A. Bruce

The paper describes the construction of 5 plugs to resist high water heads at depth within the South Deep Gold Mine, Randfontein, South Africa. A total of 20 segments were involved to create these plugs, which were 7.5 m long at the 58 Level and 6.25 m long at the50 Level. Emphasis is placed on the QA/QC and verification methods, which were developed and governed all phases of the work, from initial rock preparation and pregrouting through to the final grout tightening of the rock/plug interface and the surrounding rock. This paper is one in a series of papers detailing other aspects of the project, which was constructed largely between May 2001 and August 2003.

Jan 1, 2006

By Tiezheng Li

Keywords: Laminate Composites; Mechanical Behavior; Damage Evolution The mechanical performance of Ti-6-4-Al3Ti metal-intermetallic laminate (MIL) composites synthesized by a reactive foil sintering technique was evaluated. Crack morphology of untested Ti-6-4-Al3Ti MIL composites has been characterized by optical microscopy. Mechanical tests were performed on Ti-Al3Ti metal-intermetallic laminate (MIL) composites and pure Al3Ti, and the principal mechanisms of damage initiation and accumulation were identified experimentally. The elastic properties and anisotropy of the laminates were calculated and successfully compared with Resonant Ultrasonic Spectroscopy (RUS) measurements. The effect of residual stress on the fracture toughness of the Ti-6-4-Al3Ti MIL composites was analyzed.

Jan 1, 2005

By E. M. Bloomfield, C. A. Jermy

Geotechnical tests were carried out within an area of the coastal sand dune cordon of northern KwaZulu-Natal which is currently being exploited through mining of heavy mineral sands. In situ and laboratory tests were carried out to assess the density, strength and stability of the dune sand material before and after mining. The most stable combination of sand (>63µm) and fines(<63µm) material was determined as well as the effects of compaction on the strength and permeability of the sand dune samples. In situ DCP and density tests showed that the sand dunes fall in density immediately after mining has taken place. However, settlement of the dunes occurs with time and the density increases within the top 2 metres, and particularly once the dunes become re-vegetated. Laboratory tests carried out showed that the dune sand with between 20% and 30% added fines had the highest shear strength and dry density, but the permeability was shown to decrease steadily with increasing fines up to 40% fines added. The addition of fines would result in steadily increasing water flow problems. Compaction of the dune sands was shown to significantly increase the density and the shear strength, but with a corresponding dramatic decrease in the permeability of the material. Slope stability analysis carried out on models of the dunes with increasing fines showed that the addition of fines increases the stability of the dune sands up to a peak of about 30% fines added, and compaction further increases the stability of the dune sands. Despite the benefits of compaction on the stability of the tailings dunes, the loss of permeability is thought to outweigh the benefits as well as the high costs involved. The stability of the tailings dunes greatly increases after re-vegetation. Compaction and densification of the tailings dunes may be necessary within the top 2 m interval if large-scale construction takes place on the sand dunes. Petrographic analysis was performed to understand the granular interactions of the sand and fines fractions, and the effect of the in situ weathering of the dune sands on the stability of the sand dunes. As the fines contents increase the gaps between the sand grains are filled, until a point where the percentage of fines begins to push the sand grains apart.

Jan 1, 2003

By I. G. Townsend, S. A. Buckley, C. I. House

"SummaryBritish Petroleum plc is developing a new gold recovery process known as coal gold agglomeration (CGA) for the recovery of gold from its ores. Liberated gold grains are recovered with high efficiency by adhering to agglomerates of coal and oil. The process is simple, can recover gold grains down to very fine sizes, avoids the large scale use of cyanide and provides the industry with an important new process option.A technical appraisal of the process has been performed on an extensive range of gold bearing materials. Ore types have been identified from which high gold recoveries can be achieved. A spreadsheet based computer program has been used to estimate the preliminary capital and operating costs of the process. Comparison with established gold production costs shows that the process costs of CGA, on the appropriate ore types, are potentially very attractive, which will enable economic treatment of lower grade ores than is currently possible using conventional cyanidation. Treatment of known placer deposits or gravity concentration plant tailings may be the most rapid means of demonstrating the process at a commercial scale prior to more widespread applications.1. INTRODUCTIONWestern world gold production for the 1980s has shown rapid growth sustained by a demand for gold at a favourable price (Fig. 1). Heap leaching and CIP/CIL operations have been responsible for the major part of new production during the 1970s and 1980s with present overall production costs averaging US$200/oz in Canada, USA and Australia and US$265/oz in South Africa [l]. A great deal of research and process development effort in the 1980s has been towards the treatment of refractory ores. Operating costs for the economic processing of these ore types by currently available routes are around US$300/oz [2]."

Jan 1, 1989