Search Documents

By M. Massinaei, S. Abasi, M. Oliazadeh

Reliable measurement and control of the pulp-froth interface (froth depth) in the flotation columns is critical to achieve the desired metallurgical performance. Shallow froths result in a reduction of grade because of particle entrainment and deep froths reduce recovery because of the drop back of entrained and weak hydrophobic particles to the pulp zone. The cleaner circuit at Miduk copper concentrator consists of three parallel MicrocelTM flotation columns 4 m in diameter and 12 m in height. The interface level of the flotation columns is measured by two pressure sensors located at 1.4 and 2.4 m from the cell lip (in the collection zone). In this study the performance of the level detection system at different operating conditions was evaluated. A calibrated float-ultrasonic location system was used for measuring the actual froth depth. The results indicated that the existing level control system was subject to considerable error. The absolute error was found to be 33.27 cm. This was mainly attributed to the constant set-point value assigned to the froth density (ρf=0.3 g/cm3), which actually varies with the operating conditions. The actual froth density at different conditions was calculated and its average value (ρf=0.12 g/cm3) was re-set in the control system. This resulted in substantial reduction in the level-detecting error. Recommendations for more accurate measurement of the interface level were presented. INTRODUCTION Froth flotation is a complicated process because of many involved variables. One of the most significant controlled variables in the flotation process is the pulp-froth interface (froth depth). The froth depth has a profound influence on the metallurgical performance parameters (i.e. grade and recovery). Shallow froths result in grade reduction because of particle entrainment and deep froths reduce recovery resulted from the drop back of entrained and weak hydrophobic particles to the pulp zone (Finch and Dobby, 1990). Various techniques have been developed for measuring the interface level of the flotation cells in the last few decades. These techniques can be classified as: Techniques based on hydrostatic pressure measurements (Finch & Dobby, 1990), Techniques based on the density gradient (float) (Moys & Finch, 1988), Techniques based on conductivity measurements (Uribe-Salas, 1991), Techniques based on temperature measurements (Moys & Finch, 1989).

Jan 1, 2019

By Terry J. Kreidler

In recent years, west-central Arizona and adjacent California have become the focus of geologic and exploration attention because of its excellent exposure of detachment-fault terrane. Detachment faults, normal faults with nearly horizontal fault planes, are the result of regional extension. Rocks on the lower plate consist of mylonitized intrusive, metasedimentary and crystalline rocks highly altered to chlorite; upper plate rocks comprise sedimentary, volcanic, metasedimentary, and metavolcanic rocks. The movement of the detachment fault causes the rocks on the upper plate to be severely fractured and brecciated thus making them Ideal conduits for mineralizing fluids. Mineralization favored the more reactive sedimentary and volcanic rocks of the upper plate. Three gold deposits, located in upper plate rocks, are currently being mined along the Colorado River corridor: the Picacho Mine near Yuma, Arizona, 70 mi south of the study area; the American Girl Mine In southeastern California, 60 mi southwest; and the Copperstone Mine near the southern end of this study area. Samples from the above three mines were used to create a geochemical model of detachment-related gold deposits. Antimony, arsenic, barium, copper, mercury, molybdenum, manganese, tungsten, and zinc all occur In the mine samples in concentrations at least three times greater than found elsewhere in similar rock types. Samples taken by the Bureau from the wilderness study areas contain similar anomalous concentrations of the same elements as well as elevated concentrations of several other elements Including: lead, fluorine, cerium, uranium, and samarium.

Jan 1, 1992

By Ö. Kaya

The removal of gangue minerals from three different graphite ores (Inebolu, Akdag?madeni and Çoraklidere) from Turkey by acid leaching was studied. Acid leaching experiments were applied to the flotation bulk concentrates, which were obtained in determined optimum conditions after preliminary flotation tests. The effects of acid type, acid concentration, leaching temperature and leaching time on the dissolution of gangue minerals were studied. The most suitable leaching conditions were determined to be 20% HCl + 4% HF for acid type and concentration, 85 ºC for leaching temperature and 4 hours for leaching time. After removing the gangue minerals at these optimum conditions, the total carbon contents of the samples from Inebolu, Akdag?madeni and Çoraklidere increased from 23.51% to 40.07%, from 37.93 to 60.47% and from 42.28 to 59.47%, respectively.

Jan 1, 2009

By T Christie

Tertiary volcanic rocks make up a significant proportion of the surficial cover rocks of New Zealand, especially in the Taupo Volcanic Zone. Industrial minerals that are associated with or derived from the volcanic rocks include: amorphous silica, allophane, bentonite, diatomite, ignimbrite building stone, illite clays, halloysite clay, obsidian, perlite, pumice, sulphur, titanomagnetite ironsand and zeolite. Of these: bentonite, ignimbrite building stone, perlite, pumice and titanomagnetite ironsand have been mined and processed for 20 to 30 years, but many of the others require further characterisation of the resource and/or development of markets.   We have compiled interim mineral deposit models for halloysite clays in rhyolite and for zeolites in altered vitric tuffs. These models include geological and mineralogical attributes, which are linked to the underlying volcanic and geothermal processes that have produced the minerals and their source volcanic rocks. Halloysite clay deposits at Matauri Bay (Northland) have formed from hydrothermal alteration and weathering of rhyolite. Clinoptilolite + mordenite zeolite deposits in the Ngakuru area (Rotorua district) have formed from hydrothermal alteration of volcanic glass in lacustrine sediments and ignimbrite. Further refinement and application of these models will result in a better understanding of the mineralogy, localisation and origin of the deposits, with consequent applications in exploration and resource assessments.

Jan 1, 2001

Capture airborne respirable dust generated by an auger-type continuous mining machine to reduce workers' dust exposure. Approach Install a water-powered scrubber system, operating at 1,400 psi, on the sides of the conveyor. The scrubber draws the dusty air from the face area and discharges cleaned air into the face return. How It Works Auger-type continuous miners pose unique ventilation and dust control problems. To protect face workers from the dust, the end of the brattice is usually maintained close to the face to increase ventilation effectiveness. However, it is taken down as the machine cuts toward the exhaust side to allow the machine to complete its cut. Often, the brattice is not reinstalled in a position to most effectively control

Jan 1, 1989

By L. D. Johnson

On a project which is to develop a system to suppress coal dust explosions, a facility has been built and several devices tested. The facility is a 317-foot, 4.5-foot diameter shock tube and to date 53 tests have been carried out with methane-air and methane/coal dust-air as the explosive mixtures. Suppression of slowly propagating (up to 300 ft/sec) flame fronts has been successfully carried out on two tests using the dry chemical extinguishing agent Purple K. Delivery of the material directly into the flame front Seems to be required if effective suppression is to be accomplished.

Jan 1, 1972

By Kwang ‘Min’ Kim, Paul T. Behum

The Old Bevier Aerobic Wetland in Macon County, Missouri, was constructed between 1990 and 1991 by the Missouri Department of Natural Resources’ Land Reclamation Program for the purpose of treating acid mine drainage (AMD). The principal source of the AMD is from an underground mine that operated during the 1920's through 1950's, which was partially exposed during surface mining in the 1960’s. Limestone bedding of an AMD collection system provided alkalinity similar to an anoxic limestone drain (ALD). Because the original aerobic wetland failed when a critical dilution water supply became unavailable, the total acidity of the AMD overwhelmed the limited neutralization ability of the aerobic wetland. The aquatic vegetation deteriorated and treatment became ineffective. The Missouri Land Reclamation Program with the assistance of the Office of Surface Mining, Mid-Continent Regional Coordinating Center rehabilitated the Old Bevier Aerobic Wetland in 2001, incorporating newer technologies to improve the performance. The new system, Old Bevier II treatment facility, consists of a 2-stage vertical flow pond (VFP) with associated oxidation cells and aerobic wetlands. This paper discusses the performance of this passive AMD treatment system, updating an earlier report. The new treatment system has operated with nearly continuous net alkaline discharge and a high iron removal rate. Treatment improves during warm months when emergent vegetation is fully established and biologic activity is greater. Reduction in system efficiency is evident during winter months.

Jan 1, 2005

By Edward A. McClatchie

A novel nondispersive electro-optical gas analyzer has been designed, fabricated and tested. The instrument is based on a pressure modulated absorption technique. Key features of this new gas analyzer technique include long-term zero and calibration stability. The technique was investigated for the gases carbon dioxide (CO2), carbon monoxide (CO), methane (CH4) and nitrogen dioxide (NO2). The delivered analyzer was capable of measuring the three species CO, CO2 and NO2. It is a compact (300 cu in) package, is battery powered and weighs 15 lbs. Some thirty readings of each gas may be made on a single battery charge.

Jan 1, 1980

By Arun Vathavooran, Adrian Singh, Michael Fletcher, Rainer Imhof

The Imhoflot G-Cell, a new development in the pneumatic flotation technology (which incorporates centrifugal forces in the separating vessel) is a recent innovation in the mineral processing world. The G-Cell was invented by Dr Rainer Imhof and commercialised by Maelgwyn Mineral Services Ltd. In a short time span a number of plants and units have been successfully commissioned in the mineral processing industry. In addition, a number of industrial G-Cell flotation plants are in the process of construction for the purpose of coal preparation and environmental remediation. In this paper two industrial installations have been highlighted together with a pilot plant test programme investigating ultra fine flotation recovery for a base metal operation.

Jan 1, 2007

By J. F. Papp

In the United States, chromium has been consumed in three major markets: chemical, metallurgical, and refractory. The predominant end use for chromium in the United States is in the metallurgical market as an alloying element in the production of stainless steel. In addition to being a major stainless steel-producing country, the United States is a major world producer of chromium-containing chemicals and has used substantial amounts of chromite ore for refractory applications. Chromium use is not easily further subdivided within the chemical and refractory industries because there is insufficient publicly available information to do so; however, chromium use can be subdivided among metallurgical industry uses based on the American Iron and Steel Institute (AISI) reported shipments of stainless steel by market classification (agricultural, aircraft, automotive, etc.). It is the goal of this study to determine the distribution of U.S. chromium apparent consumption among major markets in the United States. The distribution is expressed in the form of dimensionless fractions that are computed based on documented chromium consumption by major market. The distribution of chromium among markets within the metallurgical market is computed in a similar manner. Distribution factors are first computed for the major markets, then for markets that are subdivisions of the metallurgical market. The distribution of chromium among major markets has changed substantially over the time period of analysis. The fraction of chromium consumed by the metallurgical market has increased while that of the chemical and refractory markets has declined. Within the metallurgical market, the service industry market accounts for the greatest fraction of chromium consumption followed by transportation. Electrical, machinery, and fabricated products markets account for a substantial share of the metallurgical chromium consumption.

Jan 1, 2004

By J A. Rowland

When executing a ventilation change the mine ventilation circuit is in a state of flux throughout the entire change period with discrete mine areas both under ventilated and/or over ventilated during the change process. Whilst routine risk reduction strategies such as removing electrical power and people from the mine are commonly deployed it is wise to complete the change in the shortest practical time frame. This not only minimises the chance of unacceptable concentrations of contaminants accumulating around the mine but reduces the impedance on production activities which are routinely suspended during these change periods. This paper firstly highlights the importance of the maintenance of an accurate ventilation model and discusses issues which should be considered to assist to maintain in it a suitable state of health. Further it provides some tips on how to monitor that your model is in an acceptable state of tune so that it can be confidently deployed in the change process. Finally, it details the sequential process how a finely tuned and accurate ventilation model can be utilised to carry out major ventilation changes according to appliance pressure adjustments only and without the need to constantly measure and check resultant branch flows throughout the whole change process. Also discussed are some simple practical tips which will help ensure that the ventilation change process will go according to the devised plan on the day and in the most appropriate order including checking the efficiency and accuracy of the change, after it is completed.

Oct 12, 2022

Macraes Mining Company Limited operates a 2.1 million tonnes per annum gold processing plant at Macraes Flat, Otago. This uses a conventional CIL route to treat oxide ore, and a flotation, grind, CIL route for sulfide ore. This paper describes the design and operation of this process plant.

Jan 1, 1992

By Rolland R. Mates

This paper describes the use of post- tensioned rock anchors to reduce the risk of future damage to a residential structure as a result of coal mine subsidence. The project described in this paper was performed by the Office of Surface Mining Reclamation and Enforcement (OSMRE) of the U. S. Department of the Interior. The OSMRE was created to administer Public Law 95-87, the Surface Mining Control and Reclamation Act of 1977. The responsibilities of OSMRE include "reclamation and restoration of land and water resources, adversely affected by past coal mining including prevention, abatement, control of coal mine subsidence. ?('l) Consequently, OSMRE has been addressing mine subsidence problems since its initial subsidence stabilization project in 1979. Stabilization activities have primarily consisted of supporting the overburden material by injecting materials through drilled bore holes into the underground mine voids. Injection of various materials into mine voids, including fly ash mixtures, coal refuse, cement grout, and gravel has proven to be a successful method of reducing mine subsidence-related surface movements, and has been extensively utilized in mitigating mine subsidence problems. However, the cost of drilling for injection can be extremely high in areas where the depth to the coal seam is great.

Jan 1, 1986

By S. Hamilton

Borates are essential to life, and to many products that are essential to an acceptable standard of living. They occur naturally in seawater at an average concentration of five milligrams of boron per liter. Fresh water lakes, rivers, streams and ground water generally have concentrations of about one milligram boron per liter. Borates are also present in soil at concentrations ranging from 0.1 to three milligrams of boron per kilogram. Because most of that boron is locked into insoluble minerals, clay or organic matter, boron deficiency is more widespread than boron enrichment. Borates evaporate into the atmosphere from seawater, rain, snow and hot springs. In rain and snow, natural boron concentrations range from 0.002 and 0.1 milligrams boron per liter. All told, boron moves through the atmosphere at a rate of 5 Mt to 7 Mt/a (5.5 million to 7.7 million stpy).

Jan 1, 2005

The Oregon-Idaho graben evolved after widespread tholeiitic flood basalt volcanism associated with the arrival of the plume head of the Yellowstone hotspot beneath southeastern Oregon approximately 17 - 16 Ma. The north- to north-northeast-trending, 50 km-wide graben evolved between 15.5 and 10.5 Ma during east-west extension. The graben is part of a middle Miocene back-arc rift (1100 km long) that includes the northern Nevada rift, the Baker and LaGrande grabens, and the Chief Joseph dike swarm of the Columbia River Basalt Group. The graben ceased to be a volcanotectonic depression as the cross-cutting western Snake River plain began to evolve at approximately 10.5 Ma. At about 14.3 Ma and continuing to approximately 12.6 Ma the Oregon-Idaho graben began to break up into subbasins that were bounded by intragraben fault zones. The break up was accompanied by a change to calc-alkaline volcanism that persisted within the Oregon-Idaho graben until 8.1 Ma, approximately 2.5 million years after subsidence within the graben ceased. Three intragraben fault zones have been identified and a fourth is inferred. The easternmost, the Devils Gate fault zone, coincides with the magmatic axis of the graben at approximately 14.3 Ma. By approximately 13.5 Ma the magmatic axis had shifted to the west along the Dry Creek Buttes and Wall Rock Ridge fault zones. A diffuse magmatic axis developed at approximately 12 Ma farther to the west where the fourth intragraben fault zone is inferred. In addition to serving as conduits for the ascent of basalt, basaltic andesite, rhyodacite, and rhyolite magmas, the zones focused the discharge of large geothermal systems. The intragraben fault zones display a common evolutionary pattern. The 2 to 3 km-wide zones initially control the distribution of facies in volcaniclastic sediments and the location of basalt hydrovolcanic vents. During this stage, the fault zones may have had no surface expression other than a low elevation change on a relatively low-relief landscape. As relief developed by continued deformation along the fault zones, strike-length of individual faults increased and weakly consolidated volcaniclastic sediments, silicified sediments and hot-spring sinter, and palagonite were eroded from the uplifted blocks and deposited in neighboring subbasins. It is during this stage that the large hot-spring precious-metals bearing prospects evolved. Displacements of over 150 m on a few faults within the zones and possible reversal of the sense of displacement along the zones occurred in this final stage of development. Locally, the fault zones were remobilised during the subsidence of the cross-cutting western Snake River plain. The intragraben fault zones within the Oregon-Idaho graben illustrate the relations among syntectonic volcanism and sedimentation and the evolution of geothermal systems within continental rift systems.

Jan 1, 1995

By Larry Rayburn

Design of cost effective engineered solutions to complex problems requires the team efforts of the owner, the designer and the specialty construction contractor. The basic ingredients of success required to remain competitive and still produce a quality product are creative design based on experience and sound engineering principles, plus practical aspects of constructibility. The three case histories describe creative design/construct approaches that benefited all parties. 1. Introduction The increasing demand placed on specialty contractors to provide cost effective buildable solutions to complex construction problems compels us in the industry to be highly innovative. The practice of geotechnical engineering is considered more of an "art" than perhaps the other disciplines within civil engineering largely because of the basic nature and variability of soil and rock. The geotechnical design engineer must have the knowledge of the components of his design and know the limitations of his equipment and labor force. Thus, for the design/build specialty contractor the potential for creation of unusual solutions to difficult problems is quite high.

Jan 1, 1991

By L. A. Morley

Volume IV of the final report examines the problem of indirect contact of overhead high-voltage power lines by mining personnel. This refers to the contact of energized lines by workers through some intermediate conductor such as a metallic tool or a piece of high-reaching mobile equipment, thus the term "indirect contact." The shock hazard presented by such contact has been a major cause of electrical fatalities associated with mining operations. The report volume is divided into three major areas. The first gives a general background of overhead lines, basic characteristics, and associated hazards, and continues to describe presently used techniques and devices which attempt to alleviate the contact problem. The second area narrows the discussion to the mining industry by presenting a detailed analysis of 39 overhead-line contact accidents in mining since 1970. The third major section uses the information from the first two areas to formulate recommendations to prevent these accidents and subsequent electrocutions at mining operations.

Jan 1, 1982

By F. E. Armstrong

This report describes development and application by the Bureau of Mines of techniques and instruments for using radioactive inert-gas tracers to determine flow paths through petroleum reservoirs that have natural fracture systems and for which water injection has been selected as the stimulative production method. A field test was made to prove the techniques and evaluate instrumentation. The feasibility of applying the techniques and instruments to the solution of reservoir problems in other stimulative methods of production also is discussed. Oil commonly is displaced from sandstone host rocks by the action of a driving force that causes the oil to move through interstices of the rock and into production wells. In addition to the requirements of oil being trapped within the sand pores and the presence of an effective displacement mechanism, the rock itself must have adequate permeability to permit flow of oil and other fluids.

Jan 1, 1961

By P. Hickey

"The object of this paper is to describe how the Iron Ore Company of Canada develops its management personnel. It will elaborate on the practical application of Supervisory Training and Management Development.Why are Supervisory Training and Management Development important? The answer has been the subject of many textbooks. Dr. Ken Blanchard, author and consultant, addressed this issue concisely when he said that effective managers and organizations must do two things, ""get results and develop people"". lPeople development at IOC is best illustrated through its supervisory training and management development programs. For the past twenty-five years IOC has been recognized as an industry leader in the training field. Periodic studies have played their role in establishing and maintaining this distinction. For example, in 1974, the company decided to review and up-date all its training programs. At this time, it established its own Task Force on Training and this resulted in the development of many of our present programs. Today, Supervisory Training (i.e. for first and second level management) at the Carol Project in the Labrador City area consists of various programs including: New Foreman Induction, Foreman Entrance School, Basic Management Skills, Management II, and Effective Presentations."

Jan 1, 1983

By Finlay Campbell

Nickel laterite pressure acid leach plants and reduction roast plants have had a checkered history in their engineering, construction, startup and operational reliability. Many potential projects have been the subject of detailed studies over the last thirty to forty years but relatively few have advanced to commercial production. Four reduction roast plants are currently operating, an additional one was partially constructed but never completed, and another was started up in 1974 and shut down after 12 years operation. Three acid leach plants have been built and commissioned in the last five years, trying to follow the example of the Moa Nickel plant in Cuba. An additional acid leach plant project is currently on hold, following limited construction work, its future subject to review by the owner because of potential cost over-runs. This paper attempts to discuss difficulties that may be encountered as a project is developed and will address factors which may affect production ramp-up schedule, long term production performance and overall production success. Comparisons are made with ramp-up performance at other large metallurgical plants that employ some comparable unit operations. Keywords: Caron, PAL, nickel laterite ore, ramp-up, reliability, process development, equipment design, step-out, commissioning, startup.

Jan 1, 2004