Search Documents

By D. R. Dolinar

The fall of small pieces of rock between roof bolts causes over 80 pct of the ground fall injuries in underground coal mines. Roof screen, if installed on the bolting cycle, can significantly reduce the number of these injuries. As the surface of the roof fails, the screen will have to retain the broken rock without failing or excessive deformation. Welded wire screen is the most common type of screen material used for roof surface control in underground coal mines. The load-deformation characteristics and the load capacity of welded wire screen were evaluated in the laboratory in a specially built test frame. In the frame, the square screen sections were held in place by bolts and bearing plates at the four corners while a center load was applied to the screen. The parameters evaluated included the wire gauge and configuration, the bearing plate loads and bolt spacing. The wire gauge of the tested screen was 4, 6, 8, 9 and 10. Maximum screen capacities for both load and displacement were developed for each of the wire gauge sizes along with the screen stiffness. This information can be used for screen selection and for the evaluation and determination of screen performance. DISCLAIMER: The findings and conclusions in this report have not been formally disseminated by the National Institute for Occupational Safety and Health and should not be construed to represent any agency determination or policy.

Jan 1, 2009

By J. L. Robson, C. M. Bristow

mass flow rates of particles and air (the loading ratio).

Dec 1, 1994

By Loren R. Anderson

Traditionally, an evaluation of the safety of slopes has been based on computing a safety factor against failure. In computing the safety factor, the geometry of the slope, the soil parameters and the pore pressures are treated as deterministic quantities even though they are known to be random variables. A pseudo-three-dimensional probabilistic slope stability model has been developed that treats shear strength as a random variable. The model uses the probability of a slope failure as an assessment of slope reliability. The model can accommodate zoned embankments of soil in which the strength is described by the Mohr-Coulomb strength envelope. Autocorrelation functions are used to describe the spatial correlation of the strength parameters, c and tan ø. Model error can also be included in the analysis. The model has been applied to an existing tailings dam and to several hypothetical examples. These examples are presented to illustrate the influence of the choice of the soil strength variability parameters on the probability of failure. The results show that the critical failure surface based on the minimum safety factor is not necessarily the failure surface that will yield the maximum probability of failure. The analysis of the tailings dam shows that variance reduction can be large and that the model error is the dominant source of uncertainty for the embankment analyzed.

Jan 1, 1982

By Chris Uys, Johan Labuschagne

Sishen Iron Ore Mine, located in the Northern Cape, is an open cast mine excavating approximately 100 million tons rock to produce 25 million tons of high grade haematite ore per annum. The size of the pit is approximately 12 km ‘1.5 km ‘150 metres. The final depth is planned to be around 350 metres. It is hard rock mining operation employing the conventional truck and shovel method. Mining benches are twelve and a half metres in height and are divided into blasting blocks, each consisting of approximately 300 000 tons of material.

Jan 1, 1997

This Bureau of Mines publication contains the texts of the four papers presented at the May 6-7, 1980, seminar on the role of overburden analysis in surface mining. Coverage includes the geologic distribution of pyrite and calcareous material and its relationship to overburden sampling, overburden sampling and analysis, use of soil-overburden data in mine planning and development, and minesoil classification.

Jan 1, 1981

By Howard M. Stainer

Published X-ray mass absorption coefficients were compiled and tabulated. These coefficients are required for various X-ray analytical techniques. Values obtained from 28 authors are listed for 87 elements with both experimental and calculated points included; the wavelengths range from 4.01 to 68 A. Representative graphs are presented for six elements (lithium, nitrogen, iron, silver, holmium, and uranium. A 37-item supplementary bibliography is also included.

Jan 1, 1963

By Jin Qiu

Experiments were performed to determine the extent of minor element elimination that occurred when mixtures of copper smelter dust and copper concentrate, were calcined under vacuum. Almost complete removal of the As, Sb, Bi and Pb occurred due to the conversion of the minor element compounds of these elements into their highly volatile sulphides by reaction with sulphur from the concentrate. Heat and mass balance calculations of the slag-blow in a copper converter found that ~30 tonnes of the vacuum calcine could be used to produce 100 tonnes of copper as white metal. The use of dirty concentrate as the sulphidizing agent in the vacuum calcination means that the minor element treatment capacity of the smelter complex could be increased by 60 %. Also the productivity of the converters may be increased by up to 8 % due to the supply of copper values and oxygen in the calcined mixture.

Jan 1, 2005

By C. T. Christensen

The paper gives an outline of the design, installation and performance of a series of mooring and berthing dolphins for a major ferry berth outside the port of Elsinore, Denmark. The Dolphins are large cylindrical bottle shaped and open ended steel piles vibrated into the sandy seabed. They are subsequently equipped with prefabricated fender units. Vehicle access to the ferry is via a fixed ramp and a semi-submerged linkspan. Supplementary passenger access is via a covered gangway steel bridge from an existing gangway facility to a midship door in the ferry«

Jan 1, 1989

By Mark Rybak

On August, 31, 2006, Tropical Storm Ernesto hit the City of Richmond, Virginia. The Battery Park area was hit particularly hard, as flooding forced an evacuation of the area. A large sinkhole collapsed a sewer line in the Battery Park area, blocking the pipe and causing more serious flooding. This case history describes the fast track design, bidding, and construction of an emergency tunnel to bypass the collapsed sewer. Innovative value engineering, tunneling and shaft sinking methods, and final lining design all contributed to the success of this project. The storm inundated Richmond, Virginia with up to twelve inches of rain in some areas causing widespread flooding and damage. One of the hardest hit areas of Richmond was Battery Park. A major trunk sewer in the Battery Park area collapsed causing local combined sewer and storm-water flooding. The collapsed sewer was an 8'-3" wide by 9'-6" high arch sewer that was constructed in the nineteen twenties and later filled over with municipal solid waste and a soil fill cap to current elevations. A sinkhole was created in the area of collapse approximately sixty feet deep and one hundred feet in diameter causing the existing arch sewer to become blocked. As a result of this blockage contaminated flood waters reached depths in low lying areas in excess of twenty five feet. [ ]

Jan 1, 2008

By Howard M. Stainer

Published X-ray mass absorption coefficients were compiled and tabulated. These coefficients are required for various X-ray analytical techniques. Values obtained from 28 authors are listed for 87 elements with both experimental and calculated points included; the wavelengths range from ~0.01 to 68 A. Representative graphs are presented for six elements (lithium, nitrogen, iron, silver, holmium, and uranium. A 37-item supplementary bibliography is also included.

Jan 1, 1963

By Donald Leroux, Jean-François Wilhelmy, Ahmed Bouajila

"A young private R & D organization, COREM celebrated its 10th anniversary in 2009. Managed by a consortium of nine mining and metallurgical companies, COREM has the mandate of increasing the competitiveness of its member companies through the development and transfer of mineral processing innovations. Typical technologies developed by COREM include alternative mineral processing techniques, novel operating strategies, innovative sensors and process simulation software. Many of them were developed in partnership with universities and selected research organizations.Because the COREM membership base is broad (from ferrous to base, to precious metal industries), its R & D program must deliver technologies with applications within a wide spectrum of mineral processes. Comminution, physical (gravity and magnetic) separation, flotation, cyanidation, pelletizing and thermal processes are the main topics of the R & D program. A number of new technologies have been developed and transferred to the plants of member companies. These examples of transferable technologies demonstrate the capability of COREM to impact the bottom-line of its member companies.INTRODUCTIONCOREM is a private mineral-processing R & D organization that operates from its own laboratories and pilot-plant with its own staff of professionals and technicians (about 95 persons). It is managed and financially supported by a consortium of nine mining and metallurgical companies and three provincial and federal ministries. The very ‘down-to-earth’ mission statement of COREM is to increase the competitiveness of the mineral processing plants of its members. The eighteen plants upon which the COREM technology development program is currently based can be found in Québec, Newfoundland and Labrador, New Brunswick, the Netherlands and Botswana."

Jan 1, 2010

By Ned Baker

Details are given of a Hydride Fuel System to provide 5 kg of HZ to fuel a Caterpillar 3304 engine previously modified to operate on hydrogen fuel and intended to power an underground mining vehicle. The Fuel System was installed onto the engine and the Engine/Fuel System tested under cold start conditions and a full range of engine loads and speeds. Refueling tests were also performed. The fuel system tested will support full engine power and allow delivery of at least 3/4-power on a continuous basis, from cold start conditions.

Jan 1, 1983

By John J. Sammarco

The U.S. Bureau of Mines has developed a regulated, intrinsically safe, rechargeable power supply for portable electronic equipment for underground use. The regulated output is ideal for microprocessor power requirements and is suited for operation in hazardous environments. Two rechargeable, sealed batteries are contained within the power supply. Provisions are made to use an external source of power if these batteries fail. Provisions are also made to charge these internal batteries when needed. The circuit is composed of three main circuits: the main regulator circuit, the input protection circuit, and the output protection circuit. The main regulator circuit provides remote voltage sensing, current sensing, fault monitoring, and internal thermal protection. The input protection circuit checks for excessive input current and low battery conditions. The output protection circuit contains two overvoltage detection devices. Schematics, a parts list, and a calibration procedure are provided in this report to enable readers to fabricate the power supply.

Jan 1, 1989

By M. S. Fleming

The objective was to evaluate central lubrication systems for potential use on underground mining equipment. Previous use on continuous mining equipment resulted in poor system performance because of improper selection of lubricants, component failures, and an inconsistent delivery of lubricant to the bearings. The principles and operational characteristics of systems are reviewed and evaluated, and it was concluded that systems are available which can provide reliable central lubrication if properly applied, installed, and maintained. The procedures for applying a system to a continuous miner are discussed. Investigation revealed the lack of significant information on lubrication-related equipment failures and injuries related to maintenance and repair operations, the lack of significant failure rate data for central lubrication system components, and the lack of performance standards for central lubrication systems and components. To continue the development of systems for underground mining equipment it is recommended that a data bank on failures and reliability for equipment with and without central lubrication systems be created, and standardized specifications and performance criteria be developed for central lubrication systems and components which will be used on underground mining equipment.

Jan 1, 1979

By S. R. Borrowman

This investigation by the Bureau of Mines was undertaken to develop information on the extractive metallurgy of thorite ores because potential ore bodies of this mineral have been found recently in Colorado, Idaho, and Montana. Basic information on thorite ore treatment that would be useful in appraising the potential of these and other domestic thorium resources was developed. The work was done mainly on thorite ore containing 3.87 percent ThO2 from the Powderhorn district, Colo., and on a composite sample containing 0.52 percent ThO2 from the Wet Mountains district, Colo. Limited tests of d corroborative nature subsequently were made on a sample containing 2.30 percent ThO2 from the Lemhi Pass area on the Idaho-Montana border.

Jan 1, 1962

By U. B. Kodukula

Attempts are made to evaluate the feasibility of using a water-injection cyclone for the concentration of iron ore fines. The separation characteristics of clay fines, containing large amounts of alumina and silica, from the iron values are discussed. The effects of critical variables, such as injection water rate, truncated cone diameter, spigot opening and vortex finder diameter, on the performance of a water-injection cyclone in terms of iron, alumina and silica grades; iron recoveries; and alumina and silica rejections are discussed. A set of 16 full-factorial experiments (24) was carried out to gain an understanding of the individual and interaction effects of the variables. The results indicate that classifying iron ore fines containing 63.0% iron, 2.5% alumina and 3.5% silica through a water-injection cyclone can produce concentrates with iron grades greater than 66.0% and alumina and silica contents less than 1.5% and 2.0%, respectively, at different study conditions. The achievable iron recovery values are greater than 88%, and alumina and silica rejections are more than 80% and 50%, respectively, within the specific study conditions. While the truncated cone diameter, injection water rate and spigot diameter influences the alumina rejection to a considerable extent, it is mostly influenced by the vortex finder diameter. The iron recovery and silica rejection values are mostly influenced by spigot diameter and truncated cone diameter. The effect of injection water on the concentration characteristics depend on the prevalent truncated cone diameter and spigot diameter conditions.

Jan 1, 2008

By Felix E. Mutschler

Alkaline rock-related precious metal deposits include: • orthomagmatic platinum group elements (PGE) ± gold (Au); • porphyry copper-silver-gold (Cu-Ag-Au, ±PGE); • epithermal Au-only, and Au-Ag-base metals; • submarine exhalative Kuroko-, Cyprus-, seamount- and Yellowjacket-type deposits; and • enigmatic deposits akin to Olympic Dam. Coeval epithermal deposits related to porphyry deposits suggest the two types represent separate immiscible fluids evolved in oxidized, CO2-rich alkaline magma chambers. Alkaline rock provinces develop above mantle hot-spots, but crustal structures control the final distribution of magmas and ore fluids. Prospecting guides for alkaline rock-related precious metal deposits include the presence of evolved alkaline rocks, pervasive K-metasomatic, redox and carbonatic alteration and low level Au (±Te, etc.) anomalies. Although alkaline igneous rocks crop out in less than 1 % of the area of the North American Cordillera and craton, alkaline rock-related ore deposits have produced nearly 13% of the total United States and Canadian lode gold production. Large (31-t or 1 million-oz) deposits are common (Fig. 1), and additional deposits and reserves are being discovered. New genetic models are evolving, making alkaline rock-related precious metal prospects attractive exploration targets.

Jan 1, 1991

By McLennan R. G

The principle of personal safety is as old as the human race. The application of this principle to industry is of much more recent origin, and may be said to be almost exclusively the product of the twentieth century. The enormous strides in technique and production mode prior to the turn of the century had been achieved without any real regard for the crippled human by-products of that expansive era. It was accepted that. accidents were inevitable and formed part of the price that must be paid for production. It was not until 1885 that the first Workmen's Compensation Act was passed in Germany making the employer financially liable for injuries suffered on his plant.With awakening social conscience came the first organised efforts to reduce accidents in industry. Early 19th century literature dealing with the development of powerdriven machinery and the growth of industry in Europe contains many references to the unsafe and unhealthy working conditions that accompanied the change-over from the home workshop to the industrial plant. By the year 1900, there were in Germany - and a little later in England governmental regulations dealing with the guarding of hazardous machinery. American industry, now the acknowledged leader in industrial safety, admits freely that when an organised safety movement commenced in that country, there was already a considerable amount of information available to them from European experience. The steel industry was well to the fore in this work, and in...

Jan 1, 1957

Surface subsidence that results from longwall mining can be large magnitude and can affect significant areas. Conventional methods for subsidence monitoring include leveling, global positioning system (GPS), and photogrammetric surveys. Remote sensing techniques, including aerial LiDAR, terrestrial laser scanning, and satellite-based differential interferometric synthetic aperture radar (DInSAR), are also used to measure deformation associated with subsidence. DInSAR data are different than data from conventional subsidence surveys. Images capture data over large areas (hundreds of kilometers), and each pixel (data point) in an image quantifies the average displacement over an area of square meters. DInSAR data can have fairly high time resolution; imaging periods typically range from weeks to months.

Jan 7, 2020

By J. I. Paige

The Bureau of Mines studied methods for recovering unreacted titanium minerals and petroleum coke from titanium chlorination plant wastes prior to neutralization treatment with lime. The objective was to recover valuable raw materials and to reduce the amount of waste materials that must be treated for disposal. Samples of solid wastes were physically beneficiated by gravity concentration (tabling) to recover titanium minerals containing 69.0 to 92.4 wt-pct Ti02 and by selective carbon flotation to recover petroleum coke containing 94.0 to 96.8 wt-pct C. Laboratory data indicate that the recovered titanium mineral would decrease the amount of solid waste to be disposed of from 32.8 to 53.9 wt-pct. The recovery of coke would further decrease the amount by additional 32.9 wt-pct. Preliminary tests conducted on recovering vanadium, chromium, and columbium from liquors obtained by leaching chlorination residues also have shown that (1) 97 pct of the vanadium was extracted from leach liquors in a two-stage solvent ex-traction procedure and (2) 58 pct of the columbium and 40 pct of the chromium were separated from the leach liquors by an ion exchange technique using a strong acid resin.

Jan 1, 1982